Search NASA⌕ Search

SEARCH · Search NASA

Results for “grid code”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Evaluation of the Lattice-Boltzmann Equation Solver PowerFLOW for Aerodynamic Applications

A careful comparison of the performance of a commercially available Lattice-Boltzmann Equation solver (Power-FLOW) was made with a conventional, block-structured computational fluid-dynamics code (CFL3D) for the flow over a two-dimensional NACA-0012 airfoil. The results suggest that the version of PowerFLOW used in the investigation produced solutions with large errors in the computed flow field; these errors are attributed to inadequate resolution of the boundary layer for reasons related to grid resolution and primitive turbulence modeling. The requirement of square grid cells in the PowerFLOW calculations limited the number of points that could be used to span the boundary layer on the wing and still keep the computation size small enough to fit on the available computers. Although not discussed in detail, disappointing results were also obtained with PowerFLOW for a cavity flow and for the flow around a generic helicopter configuration.

Lockard, David P.↗

Applications Performance on NAS Intel Paragon XP/S - 15#

The Numerical Aerodynamic Simulation (NAS) Systems Division received an Intel Touchstone Sigma prototype model Paragon XP/S- 15 in February, 1993. The i860 XP microprocessor with an integrated floating point unit and operating in dual -instruction mode gives peak performance of 75 million floating point operations (NIFLOPS) per second for 64 bit floating point arithmetic. It is used in the Paragon XP/S-15 which has been installed at NAS, NASA Ames Research Center. The NAS Paragon has 208 nodes and its peak performance is 15.6 GFLOPS. Here, we will report on early experience using the Paragon XP/S- 15. We have tested its performance using both kernels and applications of interest to NAS. We have measured the performance of BLAS 1, 2 and 3 both assembly-coded and Fortran coded on NAS Paragon XP/S- 15. Furthermore, we have investigated the performance of a single node one-dimensional FFT, a distributed two-dimensional FFT and a distributed three-dimensional FFT Finally, we measured the performance of NAS Parallel Benchmarks (NPB) on the Paragon and compare it with the performance obtained on other highly parallel machines, such as CM-5, CRAY T3D, IBM SP I, etc. In particular, we investigated the following issues, which can strongly affect the performance of the Paragon: a. Impact of the operating system: Intel currently uses as a default an operating system OSF/1 AD from the Open Software Foundation. The paging of Open Software Foundation (OSF) server at 22 MB to make more memory available for the application degrades the performance. We found that when the limit of 26 NIB per node out of 32 MB available is reached, the application is paged out of main memory using virtual memory. When the application starts paging, the performance is considerably reduced. We found that dynamic memory allocation can help applications performance under certain circumstances. b. Impact of data cache on the i860/XP: We measured the performance of the BLAS both assembly coded and Fortran coded. We found that the measured performance of assembly-coded BLAS is much less than what memory bandwidth limitation would predict. The influence of data cache on different sizes of vectors is also investigated using one-dimensional FFTs. c. Impact of processor layout: There are several different ways processors can be laid out within the two-dimensional grid of processors on the Paragon. We have used the FFT example to investigate performance differences based on processors layout.

Saini, Subhash↗

High Performance Parallel Methods for Space Weather Simulations

This is the final report of our NASA AISRP grant entitled 'High Performance Parallel Methods for Space Weather Simulations'. The main thrust of the proposal was to achieve significant progress towards new high-performance methods which would greatly accelerate global MHD simulations and eventually make it possible to develop first-principles based space weather simulations which run much faster than real time. We are pleased to report that with the help of this award we made major progress in this direction and developed the first parallel implicit global MHD code with adaptive mesh refinement. The main limitation of all earlier global space physics MHD codes was the explicit time stepping algorithm. Explicit time steps are limited by the Courant-Friedrichs-Lewy (CFL) condition, which essentially ensures that no information travels more than a cell size during a time step. This condition represents a non-linear penalty for highly resolved calculations, since finer grid resolution (and consequently smaller computational cells) not only results in more computational cells, but also in smaller time steps.

Hunter, Paul↗

Certification of CFD heat transfer software for turbine blade analysis

Accurate modeling of heat transfer effects is a critical component of the Turbine Branch of the Turbomachinery and Propulsion Systems Division. Being able to adequately predict and model heat flux, coolant flows, and peak temperatures are necessary for the analysis of high pressure turbine blades. To that end, the primary goal of my internship this summer will be to certify the reliability of the CFD program GlennHT for the purpose of turbine blade heat transfer analysis. GlennHT is currently in use by the engineers in the Turbine Branch who use the FORTRAN 77 version of the code for analysis. The program, however, has been updated to a FORTRAN 90 version which is more robust than the older code. In order for the new code to be distributed for use, its reliability must first be certified. Over the course of my internship I will create and run test cases using the FORTRAN 90 version of GlennHT and compare the results to older cases which are known to be accurate, If the results of the new code match those of the sample cases then the newer version will be one step closer to certification for distribution. In order to complete these it will first be necessary to become familiar with operating a number of other programs. Among them are GridPro, which is used to create a grid mesh around a blade geometry, and FieldView, whose purpose is to graphically display the results from the GlennHT program. Once enough familiarity is established with these programs to render them useful, then the work of creating and running test scenarios will begin. The work is additionally complicated by a transition in computer hardware. Most of the working computers in the Turbine Branch are Silicon Graphics machines, which will soon be replaced by LINUX PC's. My project is one of the first to make use the new PC's. The change in system architecture however, has created several software related issues which have greatly increased the time and effort investments required by the project.Although complications with the project continue to arise, it is expected that the goal of my internship can still be achieved within the remaining time period. Critical steps have been achieved and test scenarios can now be designed and run. At the completion of my internship, the FORTRAN 90 version of GlennHT should be well on its way to certification.

Jordan, William A.↗

Drag Prediction for the DLR-F6 Wing/Body and DPW Wing using CFL3D and OVERFLOW Overset Mesh

A series of overset grids was generated in response to the 3rd AIAA CFD Drag Prediction Workshop (DPW-III) which preceded the 25th Applied Aerodynamics Conference in June 2006. DPW-III focused on accurate drag prediction for wing/body and wing-alone configurations. The grid series built for each configuration consists of a coarse, medium, fine, and extra-fine mesh. The medium mesh is first constructed using the current state of best practices for overset grid generation. The medium mesh is then coarsened and enhanced by applying a factor of 1.5 to each (I,J,K) dimension. The resulting set of parametrically equivalent grids increase in size by a factor of roughly 3.5 from one level to the next denser level. CFD simulations were performed on the overset grids using two different RANS flow solvers: CFL3D and OVERFLOW. The results were post-processed using Richardson extrapolation to approximate grid converged values of lift, drag, pitching moment, and angle-of-attack at the design condition. This technique appears to work well if the solution does not contain large regions of separated flow (similar to that seen n the DLR-F6 results) and appropriate grid densities are selected. The extra-fine grid data helped to establish asymptotic grid convergence for both the OVERFLOW FX2B wing/body results and the OVERFLOW DPW-W1/W2 wing-alone results. More CFL3D data is needed to establish grid convergence trends. The medium grid was utilized beyond the grid convergence study by running each configuration at several angles-of-attack so drag polars and lift/pitching moment curves could be evaluated. The alpha sweep results are used to compare data across configurations as well as across flow solvers. With the exception of the wing/body drag polar, the two codes compare well qualitatively showing consistent incremental trends and similar wing pressure comparisons.

Sclanfani, Anthony J.↗

Discrete Adjoint-Based Design Optimization of Unsteady Turbulent Flows on Dynamic Unstructured Grids

An adjoint-based methodology for design optimization of unsteady turbulent flows on dynamic unstructured grids is described. The implementation relies on an existing unsteady three-dimensional unstructured grid solver capable of dynamic mesh simulations and discrete adjoint capabilities previously developed for steady flows. The discrete equations for the primal and adjoint systems are presented for the backward-difference family of time-integration schemes on both static and dynamic grids. The consistency of sensitivity derivatives is established via comparisons with complex-variable computations. The current work is believed to be the first verified implementation of an adjoint-based optimization methodology for the true time-dependent formulation of the Navier-Stokes equations in a practical computational code. Large-scale shape optimizations are demonstrated for turbulent flows over a tiltrotor geometry and a simulated aeroelastic motion of a fighter jet.

Nielsen, Eric J.↗

Modeling Vortex Generators in the Wind-US Code

A source term model which simulates the effects of vortex generators was implemented into the Wind-US Navier Stokes code. The source term added to the Navier-Stokes equations simulates the lift force which would result from a vane-type vortex generator in the flowfield. The implementation is user-friendly, requiring the user to specify only three quantities for each desired vortex generator: the range of grid points over which the force is to be applied and the planform area and angle of incidence of the physical vane. The model behavior was evaluated for subsonic flow in a rectangular duct with a single vane vortex generator, supersonic flow in a rectangular duct with a counterrotating vortex generator pair, and subsonic flow in an S-duct with 22 co-rotating vortex generators. The validation results indicate that the source term vortex generator model provides a useful tool for screening vortex generator configurations and gives comparable results to solutions computed using a gridded vane.

Dudek, Julianne C.↗

Assessment of Radiative Heating Uncertainty for Hyperbolic Earth Entry

This paper investigates the shock-layer radiative heating uncertainty for hyperbolic Earth entry, with the main focus being a Mars return. In Part I of this work, a baseline simulation approach involving the LAURA Navier-Stokes code with coupled ablation and radiation is presented, with the HARA radiation code being used for the radiation predictions. Flight cases representative of peak-heating Mars or asteroid return are de ned and the strong influence of coupled ablation and radiation on their aerothermodynamic environments are shown. Structural uncertainties inherent in the baseline simulations are identified, with turbulence modeling, precursor absorption, grid convergence, and radiation transport uncertainties combining for a +34% and ..24% structural uncertainty on the radiative heating. A parametric uncertainty analysis, which assumes interval uncertainties, is presented. This analysis accounts for uncertainties in the radiation models as well as heat of formation uncertainties in the flow field model. Discussions and references are provided to support the uncertainty range chosen for each parameter. A parametric uncertainty of +47.3% and -28.3% is computed for the stagnation-point radiative heating for the 15 km/s Mars-return case. A breakdown of the largest individual uncertainty contributors is presented, which includes C3 Swings cross-section, photoionization edge shift, and Opacity Project atomic lines. Combining the structural and parametric uncertainty components results in a total uncertainty of +81.3% and ..52.3% for the Mars-return case. In Part II, the computational technique and uncertainty analysis presented in Part I are applied to 1960s era shock-tube and constricted-arc experimental cases. It is shown that experiments contain shock layer temperatures and radiative ux values relevant to the Mars-return cases of present interest. Comparisons between the predictions and measurements, accounting for the uncertainty in both, are made for a range of experiments. A measure of comparison quality is de ned, which consists of the percent overlap of the predicted uncertainty bar with the corresponding measurement uncertainty bar. For nearly all cases, this percent overlap is greater than zero, and for most of the higher temperature cases (T >13,000 K) it is greater than 50%. These favorable comparisons provide evidence that the baseline computational technique and uncertainty analysis presented in Part I are adequate for Mars-return simulations. In Part III, the computational technique and uncertainty analysis presented in Part I are applied to EAST shock-tube cases. These experimental cases contain wavelength dependent intensity measurements in a wavelength range that covers 60% of the radiative intensity for the 11 km/s, 5 m radius flight case studied in Part I. Comparisons between the predictions and EAST measurements are made for a range of experiments. The uncertainty analysis presented in Part I is applied to each prediction, and comparisons are made using the metrics defined in Part II. The agreement between predictions and measurements is excellent for velocities greater than 10.5 km/s. Both the wavelength dependent and wavelength integrated intensities agree within 30% for nearly all cases considered. This agreement provides confidence in the computational technique and uncertainty analysis presented in Part I, and provides further evidence that this approach is adequate for Mars-return simulations. Part IV of this paper reviews existing experimental data that include the influence of massive ablation on radiative heating. It is concluded that this existing data is not sufficient for the present uncertainty analysis. Experiments to capture the influence of massive ablation on radiation are suggested as future work, along with further studies of the radiative precursor and improvements in the radiation properties of ablation products.

Johnston, Christopher O.↗

Modeling Vortex Generators in a Navier-Stokes Code

A source-term model that simulates the effects of vortex generators was implemented into the Wind-US Navier-Stokes code. The source term added to the Navier-Stokes equations simulates the lift force that would result from a vane-type vortex generator in the flowfield. The implementation is user-friendly, requiring the user to specify only three quantities for each desired vortex generator: the range of grid points over which the force is to be applied and the planform area and angle of incidence of the physical vane. The model behavior was evaluated for subsonic flow in a rectangular duct with a single vane vortex generator, subsonic flow in an S-duct with 22 corotating vortex generators, and supersonic flow in a rectangular duct with a counter-rotating vortex-generator pair. The model was also used to successfully simulate microramps in supersonic flow by treating each microramp as a pair of vanes with opposite angles of incidence. The validation results indicate that the source-term vortex-generator model provides a useful tool for screening vortex-generator configurations and gives comparable results to solutions computed using gridded vanes.

Dudek, Julianne C.↗

Implicit Large-Eddy Simulations of Hot and Cold Supersonic Jets in Loci-CHEM

This paper introduces a 4th-order accurate low-dissipation flux scheme for use on un- structured CFD codes, and compares this flux scheme with two others for LES calculations of hot and cold supersonic jets. The flux schemes are compared with experimental profiles of jet centerline Mach number, total temperature and total pressure, with jet spreading rate data, and with near- field acoustic measurements. The influence of grid resolution on these solution accuracy is also evaluated. The new low-dissipation flux scheme is shown to be stable on a high-speed compressible turbulent ow problem, and to be significantly more accurate than the existing baseline flux approach.

C I Morris↗

Relativistic Modeling Capabilities in Perseus Extended MHD Simulation Code for HED Plasmas

This project is submitted in response to DE-FOA-0001153, and will be carried out by Dr. Charles Seyler and Dr. Nathaniel Hamlin as post doc under the direction of Professor Seyler. The objectives are to enable PERSEUS to self-consistently model relativistic high-energy-density (HED) laboratory and astrophysical phenomena. Electrons and ions in a plasma are generally modeled either as fluids using a two-fluid code, like PERSEUS, or as particles using a Particle-In- Cell (PIC) code. Nonrelativistic PERSEUS solves the two-fluid equations, formulated in terms of a generalized Ohm’s law (GOL), so as to model about nine orders of magnitude in density variation using a local semi-implicit method. Relativistic PERSEUS preserves this structure and therefore retains these advantageous properties, enabling it to model a broader range of relativistic HED phenomena than previous codes. We have also overcome a major technical challenge associated with solving a relativistic system of equations relating conserved quantities (momentum, energy, etc.) to primitive variables (density, velocity, and pressure). We have thus far developed a relativistic version of PERSEUS and demonstrated that it recovers expected nonrelativistic results. We are currently using relativistic PERSEUS to model two HED phenomena, namely laser-plasma interactions and X-pinches, both of which show spectroscopic evidence of relativistic electrons. In an X-pinch, a section of wire carrying sufficiently large current forms a plasma column that pinches down to a point-like source, generating X-rays for use in radiographic imaging. Laser-plasma interactions have been simulated using PIC codes, and we use their results as a benchmark for comparison. However, neither PIC codes nor existing two-fluid schemes can simulate X-pinches, due to the broad range of densities which have thus far made such a simulation computationally prohibitive. In both laser-plasma interaction and Xpinch simulations, we have observed relativistic phenomena that PERSEUS could not previously model. This includes relativistic channeling of a laser into an over-dense deuterium gas (i.e. induced transparency), consistent with PIC simulation results, along with energetic electrons and ions following an X-pinch and likely accompanied by strong X-ray emission, consistent with experimental observations of energetic X-rays. This proposal includes our latest simulation results. We will improve computational efficiency with techniques that allow the use of a less refined numerical grid. This will enable extensions to three-dimensional geometries. We will improve modeling of laser-plasma interactions and X-pinches, including radiative transport processes, in order to improve comparisons with PIC simulations and experimental diagnostics. We will also model power loss through electrode surface plasmas in magnetically insulated transmission lines (MITLs). We will model relativistic astrophysical phenomena in both astrophysical and HED regimes, which could shed light on the validity of laboratory astrophysics for certain problems. These phenomena are currently modeled using PIC codes and existing relativistic two-fluid codes, neither of which can model the range of length scales of which relativistic PERSEUS is capable. There is strong potential for this project to have a broad impact on both the astrophysical and laboratory plasma communities. In the laboratory community, our work is applicable to those concerned with laser-plasma interactions such as laser-driven fusion, and those in the dense Z pinch community concerned with X-pinches and electrode surface plasmas. An improved understanding of the mechanisms of hard (i.e. high-energy) X-ray generation will likely make important contributions toward the use of X-pinches for radiography through the harnessing or mitigation of hard X-rays, depending on the application. The modeling of electrode surface plasmas, including vacuum electron flow, will improve our understanding of power loss to various loads.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Direct simulation Monte Carlo on petaflop supercomputers and beyond

The gold-standard definition of the Direct Simulation Monte Carlo (DSMC) method is given in the 1994 book by Bird [Molecular Gas Dynamics and the Direct Simulation of Gas Flows (Clarendon Press, Oxford, UK, 1994)], which refined his pioneering earlier papers in which he first formulated the method. In the intervening 25 years, DSMC has become the method of choice for modeling rarefied gas dynamics in a variety of scenarios. The chief concern to applying DSMC to more dense or even continuum flows is its computational expense compared to continuum computational fluid dynamics methods. The dramatic (nearly billion-fold) increase in speed of the largest supercomputers over the last 30 years has thus been a key enabling factor in using DSMC to model a richer variety of flows, due to the method’s inherent parallelism. We have developed the open-source SPARTA DSMC code with the goal of running DSMC efficiently on the largest machines, both current and future. It is largely an implementation of Bird’s 1994 formulation. In this work, we describe algorithms used in SPARTA to enable DSMC to operate in parallel at the scale of many billions of particles or grid cells, or with billions of surface elements. We highlight a few examples of the kinds of fundamental physics questions and engineering applications that DSMC can address at these scales.

97 MATHEMATICS AND COMPUTING↗

Measuring magnetic fields in laser-driven coils with dual-axis proton deflectometry

Abstract By driving hot electrons between two metal plates connected by a wire loop, high power lasers can generate multi-tesla, quasi-static magnetic fields in miniature coil targets. Many experiments involving laser-coil targets rely on proton deflectometry directed perpendicular to the coil axis to extract a measurement of the magnetic field. In this paper, we show that quantitative measurements using perpendicular probing are complicated by the presence of GV m −1 electric fields in the target that develop on sub-ns timescales. Probing parallel to the coil axis with fiducial grids is shown to reliably separate the electric and magnetic field measurements, giving current estimates of I ≈ 5 kA in 1 mm- and 2 mm-diameter wire loops. An analytic model of proton deflection in electric and magnetic fields is used to benchmark results from the particle-in-cell code and help deconvolve the magnetic and electric field deflections. Results are used to motivate a new experimental scheme that combines a single-plate target with axial proton probing and direct current measurements. This scheme has several important advantages over the traditional target and diagnostic set-up, enabling the robust measurement of coil magnetic fields and plasma properties, as well as making it easier to validate different theoretical models at a range of laser intensities.

Bradford, P. (ORCID:0000000296186342)↗

Simulink Modeling and Dynamic Study of Fixed-Speed, Variable-Speed, and Ternary Pumped Storage Hydropower

Pumped Storage Hydropower (PSH) is one of the most popular energy storage technologies in the world. It uses an upper reservoir to store water which can be later used during high-demand. In the United States, most of the energy storage capability actually corresponds to PSH. Moreover, PSH also brings multiple benefits to grid operation. This report presents the Simulink models of three common PSH technologies: Fixed-Speed (FS), Variable-Speed (VS), and Ternary (T)-PSH. These models are available to the general public on this GitHub repository, which contains the MATLAB model initialization files, the Simulink model files, and supplementary MATLAB code used to obtain the figures in this work. For each PSH model, an introductory description of the model components and other relevant functionalities are provided. For further information regarding the models and the initialization parameters, the reader is referred to the shared files in the repository. This report also presents the dynamic behavior of each model. The response of such models to a load event is analyzed and matched with each model's features. A custom IEEE 39 bus case is employed for the FS and T-PSH simulations, while the VS-PSH is simulated on a simplified three-bus test system due to the computational complexity of the model. For the T-PSH, the steady-state and the switching between several operating modes are also studied in this work.

13 HYDRO ENERGY↗

Comparison of viscous-shock-layer solutions by time-asymptotic and steady-state methods

Two flow-field codes employing the time- and space-marching numerical techniques were evaluated. Both methods were used to analyze the flow field around a massively blown Jupiter entry probe under perfect-gas conditions. In order to obtain a direct point-by-point comparison, the computations were made by using identical grids and turbulence models. For the same degree of accuracy, the space-marching scheme takes much less time as compared to the time-marching method and would appear to provide accurate results for the problems with nonequilibrium chemistry, free from the effect of local differences in time on the final solution which is inherent in time-marching methods. With the time-marching method, however, the solutions are obtainable for the realistic entry probe shapes with massive or uniform surface blowing rates; whereas, with the space-marching technique, it is difficult to obtain converged solutions for such flow conditions. The choice of the numerical method is, therefore, problem dependent. Both methods give equally good results for the cases where results are compared with experimental data.

Gupta, R. N.↗

Computer program for plotting and fairing wind-tunnel data

A detailed description of the Langley computer program PLOTWD which plots and fairs experimental wind-tunnel data is presented. The program was written for use primarily on the Langley CDC computer and CALCOMP plotters. The fundamental operating features of the program are that the input data are read and written to a random-access file for use during program execution, that the data for a selected run can be sorted and edited to delete duplicate points, and that the data can be plotted and faired using tension splines, least-squares polynomial, or least-squares cubic-spline curves. The most noteworthy feature of the program is the simplicity of the user-supplied input requirements. Several subroutines are also included that can be used to draw grid lines, zero lines, axis scale values and lables, and legends. A detailed description of the program operational features and each sub-program are presented. The general application of the program is also discussed together with the input and output for two typical plot types. A listing of the program code, user-guide, and output description are presented in appendices. The program has been in use at Langley for several years and has proven to be both easy to use and versatile.

Morgan, H. L., Jr.↗

NASA Ames Research Center's parabolized Navier-Stokes code - A critical evaluation of heat-transfer predictions

The viscous supersonic/hypersonic flow over a biconic configuration was numerically simulated using the NASA Ames Research Center's Parabolized Navier-Stokes (PNS) code, and results obtained for the effects of various computational parameters on the heat transfer are compared with experimental results. The PNS code is found to provide accurate results for heat transfer parameters using low smoothing coefficient values, assuming that the radial spacing is at some small value and that the body is simple in cross section. For the cases considered, the nominal value of the spatial step size was 0.05, and the grid density was 45 points in the meridional direction and 30 points in the radial direction.

Chaussee, Denny S.↗

Explicit and implicit solution of the Navier-Stokes equations on a massively parallel computer

The design, implementation, and performance of a two-dimensional time-accurate Navier-Stokes solver for the CM2 supercomputer are described. The program uses a single processor for each grid point. Two different time-stepping methods have so far been implemented: an explicit third-order Runge-Kutta method and an implicit approximation-factorization method. The CM2 results are checked against those of a mature well-vectorized Cray 2 program, both for correctness and performance. The code is found to be correct, and the performance in some cases is up to several times that of the Cray 2.

Levit, Creon↗