Search NASA⌕ Search

SEARCH · Search NASA

Results for “hydrogen program”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Experimental evaluation of heat transfer on a 1030:1 area ratio rocket nozzle

A 1030:1 carbon steel, heat-sink nozzle was tested. The test conditions included a nominal chamber pressure of 2413 kN/sq m and a mixture ratio range of 2.78 to 5.49. The propellants were gaseous oxygen and gaseous hydrogen. Outer wall temperature measurements were used to calculate the inner wall temperature and the heat flux and heat rate to the nozzle at specified axial locations. The experimental heat fluxes were compared to those predicted by the Two-Dimensional Kinetics (TDK) computer model analysis program. When laminar boundary layer flow was assumed in the analysis, the predicted values were within 15 percent of the experimental values for the area ratios of 20 to 975. However, when turbulent boundary layer conditions were assumed, the predicted values were approximately 120 percent higher than the experimental values. A study was performed to determine if the conditions within the nozzle could sustain a laminar boundary layer. Using the flow properties predicted by TDK, the momentum-thickness Reynolds number was calculated, and the point of transition to turbulent flow was predicted. The predicted transition point was within 0.5 inches of the nozzle throat. Calculations of the acceleration parameter were then made to determine if the flow conditions could produce relaminarization of the boundary layer. It was determined that if the boundary layer flow was inclined to transition to turbulent, the acceleration conditions within the nozzle would tend to suppress turbulence and keep the flow laminar-like.

Kacynski, Kenneth J.↗

Fluid-thermal-structural study of aerodynamically heated leading edges

A finite element approach for integrated fluid-thermal-structural analysis of aerodynamically heated leading edges is presented. The Navier-Stokes equations for high speed compressible flow, the energy equation, and the quasi-static equilibrium equations for the leading edge are solved using a single finite element approach in one integrated, vectorized computer program called LIFTS. The fluid-thermal-structural coupling is studied for Mach 6.47 flow over a 3-in diam cylinder for which the flow behavior and the aerothermal loads are calibrated by experimental data. Issues of the thermal-structural response are studied for hydrogen-cooled, super thermal conducting leading edges subjected to intense aerodynamic heating.

Deuchamphai, Pramote↗

Nickel-hydrogen cell low-Earth life test update

When individual pressure vessel (IPV) nickel-hydrogen (Ni/H2) cells were selected as the energy storage system for the Space Station Freedom in March of 1986, a limited database existed on life and performance characteristics of these cells in a low earth orbit (LEO) regime. Therefore, NASA LeRC initiated a Ni/H2 cell test program with the primary objectives of building a test facility, procuring cells from existing NASA contracts, and screening several cell designs by life testing in a LEO 35 percent depth of discharge (DOD) scenario. A total of 40 cells incorporating 13 designs were purchased from Yardney, Hughes, and Eagle-Picher. Thirty-two of the cells purchased were 65 A-hr nameplate capacity and eight cells were 50 A-hr. Yardney and Eagle-Picher cells were built with both the Air Force recirculating and the advanced back-to-back electrode stack configurations and incorporated 31 and 26 percent KOH. Acceptance testing of the first delivered cells began in March of 1988, with life testing following in September of that year.Performance comparisons of these cells are made here while specifically addressing life test data relative to the design differences.

Frate, David T.↗

A new facility for advanced rocket propulsion research

A new test facility was constructed at the NASA Lewis Research Center Rocket Laboratory for the purpose of conducting rocket propulsion research at up to 8.9 kN (2000 lbf) thrust, using liquid oxygen and gaseous hydrogen propellants. A laser room adjacent to the test cell provides access to the rocket engine for advanced laser diagnostic systems. The size and location of the test cell provide the ability to conduct large amounts of testing in short time periods, with rapid turnover between programs. These capabilities make the new test facility an important asset for basic and applied rocket propulsion research.

Zoeckler, Joseph G.↗

The pH profile for acid-induced elongation of coleoptile and epicotyl sections is consistent with the acid-growth theory

The acid-growth theory predicts that a solution with a pH identical to that of the apoplast of auxin-treated tissues (4.5.-5.0) should induce elongation at a rate comparable to that of auxin. Different pH profiles for elongation have been obtained, however, depending on the type of pretreatment between harvest of the sections and the start of the pH-incubations. To determine the acid sensitivity under in vivo conditions, oat (Avena sativa L.) coleoptile, maize (Zea mays L.) coleoptile and pea (Pisum sativum L.) epicotyl sections were abraded so that exogenous buffers could penetrate the free space, and placed in buffered solutions of pH 3.5-6.5 without any preincubation. The extension, without auxin, was measured over the first 3 h. Experiments conducted in three laboratories produced similar results. For all three species, sections placed in buffer without pretreatment elongated at least threefold faster at pH 5.0 than at 6.0 or 6.5, and the rate elongation at pH 5.0 was comparable to that induced by auxin. Pretreatment of abraded sections with pH-6.5 buffer or distilled water adjusted to pH 6.5 or above gave similar results. We conclude that the pH present in the apoplast of auxin-treated coleoptile and stems is sufficiently low to account for the initial growth response to auxin.

NASA Discipline Plant Biology↗

The influence of calcium and pH on growth in primary roots of Zea mays

We investigated the interaction of Ca2+ and pH on root elongation in Zea mays L. cv. B73 x Missouri 17 and cv. Merit. Seedlings were raised to contain high levels of Ca2+ (HC, imbibed and raised in 10 mM CaCl2) or low levels of Ca2+ (LC, imbibed and raised in distilled water). In HC roots, lowering the pH (5 mM MES/Tris) from 6.5 to 4.5 resulted in strong, long-lasting growth promotion. Surprisingly, increasing the pH from 6.5 to 8.5 also resulted in strong growth promotion. In LC roots acidification of the medium (pH 6.5 to 4.5) resulted in transient growth stimulation followed by a gradual decline in the growth rate toward zero. Exposure of LC roots to high pH (pH shift from 6.5 to 8.5) also promoted growth. Addition of EGTA resulted in strong growth promotion in both LC and HC roots. The ability of EGTA to stimulate growth appeared not to be related to H+ release from EGTA upon Ca2+ chelation since, 1) LC roots showed a strong and prolonged response to EGTA, but only a transient response to acid pH, and 2) promotion of growth by EGTA was observed in strongly buffered solutions. We also examined the pH dependence of the release of 45Ca2+ from roots of 3-day-old seedlings grown from grains imbibed in 45Ca2+. Release of 45Ca2+ from the root into agar blocks placed on the root surface was greater the more acidic the pH of the blocks. The results indicate that Ca2+ may be necessary for the acid growth response in roots.

Non-NASA Center↗

Somatic proembryo production from excised, wounded zygotic carrot embryos on hormone-free medium: evaluation of the effects of pH, ethylene and activated charcoal

Wounded zygotic embryos of cultivated carrot produce somatic proembryos on hormone-free nutrient medium containing 1 mM NH4+ as the sole nitrogen source. Continued maintenance of proembryos on this medium leads to a "pure" culture of preglobular stage proembryos (PGSPs). Ethylene had no effect on this process. Also, somatic embryo production was not affected by growing cultures on activated charcoal-impregnated filter papers. However, somatic proembyros initiated on activated charcoal papers were not maintainable as PGSPs and developed into later embryo stages. Normally, medium pH dropped from 5.7 to 4 during each subculture period, but when using activated charcoal papers the pH endpoint was around 6 - 7 due to a leachable substance(s) within the filter papers. When powdered, activated charcoal was used in the medium as an adsorbent of products potentially released after wounding, pH dropped at the normal rate and to the expected levels; proembryos did not mature into later embryo stages and were maintainable exclusively as PGSPs. Low pH (approximately 4) is detrimental to proembyro production, but is essential to maintaining PGSPs on hormone-free nutrient medium, whereas a sustained pH > or = 5.7 allows continued development of PGSPs into later embryo stages.

NASA Program Space Biology↗

Pathways of proton transfer in the light-driven pump bacteriorhodopsin

The mechanism of proton transport in the light-driven pump bacteriorhodopsin is beginning to be understood. Light causes the all-trans to 13-cis isomerization of the retinal chromophore. This sets off a sequential and directed series of transient decreases in the pKa's of a) the retinal Schiff base, b) an extracellular proton release complex which includes asp-85, and c) a cytoplasmic proton uptake complex which includes asp-96. The timing of these pKa changes during the photoreaction cycle causes sequential proton transfers which result in the net movement of a proton across the protein, from the cytoplasmic to the extracellular surface.

NASA Discipline Number 52-30↗

Limiting concentrations of activated mononucleotides necessary for poly(C)-directed elongation of oligoguanylates

Selected imidazolide-activated nucleotides have been subjected to hydrolysis under conditions similar to those that favor their template-directed oligomerization. Rate constants of hydrolysis of the P-N bond in guanosine 5'-monophosphate 2-methylimidazolide (2-MeImpG) and in guanosine 5'-monophosphate imidazolide (ImpG), kh, have been determined in the presence/absence of magnesium ion as a function of temperature and polycytidylate [poly(C)] concentration. Using the rate constant of hydrolysis of 2-MeImpG and the rate constant of elongation, i.e., the reaction of an oligoguanylate with 2-MeImpG in the presence of poly(C) acting as template, the limiting concentration of 2-MeImpG necessary for oligonucleotide elongation to compete with hydrolysis can be calculated. The limiting concentration is defined as the initial concentration of monomer that results in its equal consumption by hydrolysis and by elongation. These limiting concentrations of 2-MeImpG are found to be 1.7 mM at 37 degrees C and 0.36 mM at 1 degrees C. Boundary conditions in the form of limiting concentration of activated nucleotide may be used to evaluate a prebiotic model for chemical synthesis of biopolymers. For instance, the limiting concentration of monomer can be used as a basis of comparison among catalytic, but nonenzymatic, RNA-type systems. We also determined the rate constant of dimerization of 2-MeImpG, k2 = 0.45 +/- 0.06 M-1 h-1 in the absence of poly(C), and 0.45 +/- 0.06 less than or equal to k2 less than or equal to 0.97 +/- 0.13 M-1 h-1 in its presence at 37 degrees C and pH 7.95.(ABSTRACT TRUNCATED AT 250 WORDS).

NASA Discipline Number 52-20↗

Beagle to the Moon: An Experiment Package to Measure Polar Ice and Volatiles in Permanently Shadowed Areas or Beneath the Lunar Surface

Near the beginning of the next decade we will see the launch of scientific payloads to the lunar surface to begin laying the foundations for the return to the moon in the Vision for Space Exploration. Shortly thereafter, astronauts will return to the lunar surface and have the ability to place scientific packages on the surface that will provide information about lunar resources and compositions of materials in permanently shadowed regions of the moon (1). One of the important questions which must be answered early in the program is whether there are lunar resources which would facilitate "living off the land" and not require the transport of resources and consumables from Earth (2). The Beagle science package is the ideal payload (3) to use on the lunar surface for determining the nature of hydrogen, water and lunar volatiles found in the polar regions which could support the Vision for Space Exploration

Gibson, E. K.↗

Purge Monitoring Technology for Gaseous Helium (GHe) Conservation

John C. Stennis Space Center provides rocket engine propulsion testing for the NASA space programs. Since the development of the Space Shuttle, every Space Shuttle Main Engine (SSME) has gone through acceptance testing before going to Kennedy Space Center for integration into the Space Shuttle. The SSME is a large cryogenic rocket engine that used Liquid Oxygen (LO2) and Liquid Hydrogen (LH2) as propellants. Due to the extremely cold cryogenic conditions of this environment, an inert gas, helium, is used as a purge for the engine and propellant lines since it can be used without freezing in the cryogenic environment. As NASA moves forward with the development of the new ARES V launch system, the main engines as well as the upper stage engine will use cryogenic propellants and will require gaseous helium during the development testing of each of these engines. The main engine for the ARES V will be similar in size to the SSME.

Dickey, Jonathan↗

Behavior under LOCA conditions on enhanced accident tolerant chromium coated zircaloy-4 claddings

For enhanced accident tolerant fuels for light water reactors application, chromium coatings on zirconium based nuclear fuel claddings are developed and studied at CEA in the framework of the French CEA-EDF-AREVA collaborative program. The results obtained so far, mainly on Zircaloy-4 substrate, show very good corrosion resistance in nominal conditions and significant enhancement of the resistance of the material to oxidation in steam at high temperature (HT), up to 1300 Celsius degrees, with a drastic decrease of hydrogen release and/or pick-up. The present paper reports some new results obtained on chromium coated Zircaloy-4 claddings tested in loss-of-coolant accident (LOCA) conditions. In order to investigate the potential effect of the coating on the cladding mechanical behavior at HT and the capacity of the coating to sustain significant substrate deformation (i.e., during ballooning until burst occurrence) without generalized cracking/peeling, a preliminary limited set of internal pressure creep and temperature ramp tests have been performed in steam environment thanks to the EDGAR facility. The thermal-mechanical tests were done for testing/burst temperatures ranging from 600 C. degrees (α{sub Zr} phase domain) up to 1000 C. degrees (β{sub Zr} phase domain) on 50 cm long low-tin Zircaloy-4 cladding samples with a 15 μm thick outer chromium coating. It is shown that: -) whatever the applied temperature/pressure values, the chromium coating is still fully adherent after having experienced ballooning and burst, including at the vicinity of the burst opening where the Zircaloy-4 clad substrate is highly deformed; -) a HT strengthening effect of the coating on the overall creep clad behavior is evidenced when compared to uncoated Zircaloy-4 cladding materials tested in the same conditions; -) as a consequence, it is observed that, in the 600-750 C. degrees temperature range (α{sub Zr} phase domain) and after burst occurrence, the balloon sizes (i.e., 'uniform' and maximum hoop strains) are generally reduced when compared to uncoated materials; -) regarding the burst mechanism in the β{sub Zr} phase temperature range (1000 C. degrees), it is interesting to observe that, even if some ballooning occurred prior to the cladding failure, the actual burst openings are generally very small (in the order of 1 mm{sub 2} or less), reducing the risk of fuel fragments dispersal in the coolant.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Some NASA Perspectives on H2

This presentation provides the NASA perspective for government and industry technology developers world-wide who are exploring the potential for hydrogen (H2) in aviation applications including electric aircraft, airport vehicles, and airport related equipment. NASA’s H2 interest has been related to vehicle-level technology development and integration only, but NASA is keenly aware of the necessity of work focused on solving the challenges of H2 airport infrastructure. Some historical perspectives are provided on NASA efforts in H2 fuel cell development for space and aeronautics applications. NASA’s current research portfolio includes some investigation of H2 energy storage and hydrocarbon conversion for fuel cells on electric aircraft. There is no current emphasis on the other H2-related challenges. Over the years NASA has conducted research into “Quiet Green Transport” with a H2 fuel cell powered aircraft, an Emissionless Aircraft Study with Non Flow Through – Regenerative Fuel Cell (NFT-RFC) technology which captures the water, and an H2 fuel cell powered Unmanned Aerial Vehicle (UAV) study. NASA has flown a long endurance UAV using a RFC in the Low Emissions Alternative Power (LEAP) program. Recently, NASA conducted feasibility studies on hybrid SOFC with onboard hydrocarbon fuel reformation for aircraft primary propulsive power and secondary power under the Fostering Ultra-Efficient, Low-Emitting Aviation Power (FUELEAP) program. NASA currently has a multiyear program with the Center for Cryogenic High-Efficiency Electrical Technologies for Aircraft (CHEETA) to explore the benefits of using cryogenic H2 on aircraft for fuel cell propulsion and to provide superconductivity in electrical power management on the aircraft.

Power↗

Selective Conversion of CO 2 to Methanol on a In 2 O 3– x –TiO 2 (110) Interface: Importance of Oxide–Oxide Interactions

Methanol is a strategic energy vector for the storage and delivery of energy and is a widely used precursor for the synthesis of many high-value chemicals. The hydrogenation of carbon dioxide (CO 2 ) into methanol is a key process in industrial operations. Here, in this study, we show that an oxide-oxide interface generated by a low loading (0.15 ML) of In 2 O 3-x on a TiO 2 (110) substrate has a high activity and selectivity as a catalyst for the CO 2 + 3H 2 → CH 3 OH + H 2 O process. The properties of the In 2 O 3-x -TiO 2 interface under reaction conditions were investigated using a combination of synchrotron-based ambient pressure X-ray photoelectron spectroscopy (AP-XPS), temperature programmed desorption (TPD), and catalytic testing. The In 2 O 3-x overlayer spread out on top of the titania and was rich in defects and O vacancies that activated CO 2 and H 2 as reactants, without destroying CH 3 O and CH 3 OH as reaction products. The In 2 O 3-x /TiO 2 (110) catalyst is at least one order of magnitude more active than bulk indium oxide while maintaining a very high selectivity (~80%) towards methanol production. Under the rich hydrogen environment of methanol synthesis, the oxide-oxide interactions allowed only a partial reduction of the In cations, preventing the formation of metal alloys as seen in the case of catalysts with metal-indium oxide interfaces. Thus, the dispersion of low loadings of In 2 O 3-x on a stable oxide substrate is a valid and low-cost approach for generating efficient catalysts for CO 2 valorization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A program for calculating expansion-tube flow quantities for real-gas mixtures and comparison with experimental results

A computer program written in FORTRAN 4 language is presented which determines expansion-tube flow quantities for real test gases CO2 N2, O2, Ar, He, and H2, or mixtures of these gases, in thermochemical equilibrium. The effects of dissociation and first and second ionization are included. Flow quantities behind the incident shock into the quiescent test gas are determined from the pressure and temperature of the quiescent test gas in conjunction with: (1) incident-shock velocity, (2) static pressure immediately behind the incident shock, or (3) pressure and temperature of the driver gas (imperfect hydrogen or helium). The effect of the possible existence of a shock reflection at the secondary diaphragm of the expansion tube is included. Expansion-tube test-section flow conditions are obtained by performing an isentropic unsteady expansion from the conditions behind the incident shock or reflected shock to either the test-region velocity or the static pressure. Both a thermochemical-equilibrium expansion and a frozen expansion are included. Flow conditions immediately behind the bow shock of a model positioned at the test section are also determined. Results from the program are compared with preliminary experimental data obtained in the Langley 6-inch expansion tube.

Miller, C. G., III↗

X-43D Conceptual Design and Feasibility Study

NASA s Next Generation Launch Technology (NGLT) Program, in conjunction with the office of the Director of Defense Research and Engineering (DDR&E), developed an integrated hypersonic technology demonstration roadmap. This roadmap is an integral part of the National Aerospace Initiative (NAI), a multi-year, multi-agency cooperative effort to invest in and develop, among other things, hypersonic technologies. This roadmap contains key ground and flight demonstrations required along the path to developing a reusable hypersonic space access system. One of the key flight demonstrations required for systems that will operate in the high Mach number regime is the X-43D. As currently conceived, the X-43D is a Mach 15 flight test vehicle that incorporates a hydrogen-fueled scramjet engine. The purpose of the X-43D is to gather high Mach number flight environment and engine operability information which is difficult, if not impossible, to gather on the ground. During 2003, the NGLT Future Hypersonic Flight Demonstration Office initiated a feasibility study on the X-43D. The objective of the study was to develop a baseline conceptual design, assess its performance, and identify the key technical issues. The study also produced a baseline program plan, schedule, and cost, along with a list of key programmatic risks.

Johnson, Donald B.↗

Preliminary Process and Instrumentation Design of Advanced Reactor Integration with Refineries and Hydrogen Production Facilities

With the ongoing push to decarbonize energy use and especially greenhouse gas emissions across all sectors, there are incentives to investigate how nuclear reactors may be used to generate clean energy and be used in various energy economies beyond just the electrical grid. Two initial integrations, high temperature steam electrolysis (HTSE) and oil refineries, are investigated in this first DOE Integrated Energy Systems (IES) program detailed industrial integration design report. Increasingly detailed reports are anticipated both for the industries discussed in this report and for additional industries in the future of the program. This report is a robust starting point showing how integration thermodynamic analysis establishes the requirements on the reactor and methods by which those requirements can be evaluated for specific reactor designs. Two Advanced Reactor Demonstration Program awardees are selected as representative designs for their respective technologies: NuScale for light-water reactors (LWRs) and X-Energy for high temperature gas reactors (HTGRs). Other reactor technologies or specific reactor configurations would require specific analysis similar to what is done in this report, thus this report can be a reference point by which to extend this work to other nuclear plant designs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Understanding Fundamental Material Degradation Processes in High Temperature Aggressive Chemomechanical Environments

The objective of this project is to develop a fundamental understanding of the mechanisms that limit materials durability for very high-temperature applications. Current design limitations are based on material strength and corrosion resistance. This project will characterize the interactions of high-temperature creep, fatigue, and environmental attack in structural metallic alloys of interest for the very high-temperature gas-cooled reactor (VHTR) or Next–Generation Nuclear Plant (NGNP) and for the associated thermo-chemical processing systems for hydrogen generation. Each of these degradation processes presents a major materials design challenge on its own, but in combination, they can act synergistically to rapidly degrade materials and limit component lives. This research and development effort will provide experimental results to characterize creep-fatigue-environment interactions and develop predictive models to define operation limits for high-temperature structural material applications. Researchers will study individually and in combination creep-fatigue-environmental attack processes in Alloys 617, 230, and 800H, as well as in an advanced Ni-Cr oxide dispersion strengthened steel (ODS) system. For comparison, the study will also examine basic degradation processes in nichrome (Ni-20Cr), which is a basis for most high-temperature structural materials, as well as many of the superalloys. These materials are selected to represent primary candidate alloys, one advanced developmental alloy that may have superior high-temperature durability, and one model system on which basic performance and modeling efforts can be based. The research program is presented in four parts, which all complement each other. The first three are primarily experimental in nature, and the last will tie the work together in a coordinated modeling effort. The sections are (1) dynamic creep-fatigue-environment process, (2) subcritical crack processes, (3) dynamic corrosion – crack initiation processes, and (4) modeling.

36 MATERIALS SCIENCE↗