Search NASA⌕ Search

SEARCH · Search NASA

Results for “MONOCRYSTALS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Nanostructured light-absorbing crystalline CuIn{sub (1–x)}Ga{sub x}Se{sub 2} thin films grown through high flux, low energy ion irradiation

A hybrid effusion/sputtering vacuum system was modified with an inductively coupled plasma (ICP) coil enabling ion assisted physical vapor deposition of CuIn{sub 1−x}Ga{sub x}Se{sub 2} thin films on GaAs single crystals and stainless steel foils. With <80 W rf power to the ICP coil at 620–740 °C, film morphologies were unchanged compared to those grown without the ICP. At low temperature (600–670 °C) and high rf power (80–400 W), a light absorbing nanostructured highly anisotropic platelet morphology was produced with surface planes dominated by (112){sub T} facets. At 80–400 W rf power and 640–740 °C, both interconnected void and small platelet morphologies were observed while at >270 W and above >715 °C nanostructured pillars with large inter-pillar voids were produced. The latter appeared black and exhibited a strong (112){sub T} texture with interpillar twist angles of ±8°. Application of a negative dc bias of 0–50 V to the film during growth was not found to alter the film morphology or stoichiometry. The results are interpreted as resulting from the plasma causing strong etching favoring formation of (112){sub T} planes and preferential nucleation of new grains, balanced against conventional thermal diffusion and normal growth mechanisms at higher temperatures. The absence of effects due to applied substrate bias suggests that physical sputtering or ion bombardment effects were minimal. The nanostructured platelet and pillar films were found to exhibit less than one percent reflectivity at angles up to 75° from the surface normal.

36 MATERIALS SCIENCE↗

Diamond sensors and polycapillary lenses for X-ray absorption spectroscopy

Diamond sensors are evaluated as incident beam monitors for X-ray absorption spectroscopy experiments. These single crystal devices pose a challenge for an energy-scanning experiment using hard X-rays due to the effect of diffraction from the crystalline sensor at energies which meet the Bragg condition. This problem is eliminated by combination with polycapillary lenses. The convergence angle of the beam exiting the lens is large compared to rocking curve widths of the diamond. A ray exiting one capillary from the lens meets the Bragg condition for any reflection at a different energy from the rays exiting adjacent capillaries. This serves to broaden each diffraction peak over a wide energy range, allowing linear measurement of incident intensity over the range of the energy scan. Extended X-ray absorption fine structure data are measured with a combination of a polycapillary lens and a diamond incident beam monitor. These data are of comparable quality to data measured without a lens and with an ionization chamber monitoring the incident beam intensity.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Molecular dynamics simulation of self-rotation effects on ultra-precision polishing of single-crystal copper

Understanding the behaviors of the material removal mechanism of ultra-precision polishing process has been a critical issue of generating well-formed surface. In order to make clear the abrasive self-rotation effects on material removal at the atomic level, a three-dimensional molecular dynamics (MD) model is conducted to study the mechanics of ultra-precision polishing on single-crystal copper with a diamond abrasive and the effects of abrasive self-rotation velocity and direction. Morse potential energy function and EAM potential energy function are applied to model the copper/diamond and copper/copper interactions, respectively. The simulation results show that the deformation mechanism of single-crystal copper is due to the formation and movement of dislocations in the specimen. In addition, with the increasing of abrasive self-rotation velocity, the deformation mechanism falls from cutting to plowing regimes. The abrasive self-rotation velocity and direction have effects on the morphology and quality of the specimen surface, distribution and evolution of defects under the surface of the specimen. Also, the interatomic force between abrasive and specimen is studied to account for the effects of different polishing conditions.

36 MATERIALS SCIENCE↗

Influence of crystal mosaicity on axial channeling effects and lattice site determination of impurities

Using the electron emission channeling and Rutherford backscattering/channeling techniques, the influence of the mosaicity of a thin film on the axial channeling of charged particles was investigated. It is found that crystal mosaicity leads to a broadening and a degradation of the experimental channeling effects. This phenomenon, which is shown to be of major importance when assessing the lattice site of impurities in a single crystal, can be modeled quantitatively by using the mosaic tilt and twist components derived from X-ray rocking curve scans. As a case study, we illustrate that our approach allows to accurately determine the lattice site of Er in AlN, despite the significant influence of mosaicity on the channeling measurements.

36 MATERIALS SCIENCE↗

Thermal conductivity of Er{sup +3}:Y{sub 2}O{sub 3} films grown by atomic layer deposition

Cross-plane thermal conductivity of 800, 458, and 110 nm erbium-doped crystalline yttria (Er{sup +3}:Y{sub 2}O{sub 3}) films deposited via atomic layer deposition was measured using the 3ω method at room temperature. Thermal conductivity results show 16-fold increase in thermal conductivity from 0.49 W m{sup −1}K{sup −1} to 8 W m{sup −1}K{sup −1} upon post deposition annealing, partially due to the suppression of the number of the -OH/H{sub 2}O bonds in the films after annealing. Thermal conductivity of the annealed film was ∼70% lower than undoped bulk single crystal yttria. The cumulative interface thermal resistivity of substrate-Er{sup +3}:Y{sub 2}O{sub 3}-metal heater was determined to be ∼2.5 × 10{sup −8} m{sup 2} K/W.

36 MATERIALS SCIENCE↗

Photo-Seebeck effect in tetragonal PbO single crystals

We report the observation of photo-Seebeck effect in tetragonal PbO crystals. The photo-induced carriers contribute to the transport phenomena, and consequently the electrical conductivity increases and the Seebeck coefficient decreases with increasing photon flux density. A parallel-circuit model is used to evaluate the actual contributions of photo-excited carriers from the measured transport data. The photo-induced carrier concentration estimated from the Seebeck coefficient increases almost linearly with increasing photon flux density, indicating a successful photo-doping effect on the thermoelectric property. The mobility decreases by illumination but the reduction rate strongly depends on the illuminated photon energy. Possible mechanisms of such photon-energy-dependent mobility are discussed.

36 MATERIALS SCIENCE↗

Magnetic field induced discontinuous spin reorientation in ErFeO{sub 3} single crystal

The spin reorientation of ErFeO{sub 3} that spontaneously occurs at low temperature has been previously determined to be a process involving the continuous rotation of Fe{sup 3+} spins. In this work, the dynamic process of spin reorientation in ErFeO{sub 3} single crystal has been investigated by AC susceptibility measurements at various frequencies and static magnetic fields. Interestingly, two completely discontinuous steps are induced by a relatively large static magnetic field due to the variation in the magnetic anisotropy during this process. It provides deeper insights into the intriguing magnetic exchange interactions which dominate the sophisticated magnetic phase transitions in the orthoferrite systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Polymer/metal hybrid multilayers modified Schottky devices

Insulating, polymethylmethacrylate (PMMA), and semiconducting, poly(3-hexylthiophene) (P3HT), nanometer thick polymers/Au nanoparticles based hybrid multilayers (HyMLs) were fabricated on p-Si single-crystal substrate. An iterative method, which involves, respectively, spin-coating (PMMA and P3HT deposition) and sputtering (Au nanoparticles deposition) techniques to prepare Au/HyMLs/p-Si Schottky device, was used. The barrier height and the ideality factor of the Au/HyMLs/p-Si Schottky devices were investigated by current-voltage measurements in the thickness range of 1–5 bilayers. It was observed that the barrier height of such hybrid layered systems can be tuned as a function of bilayers number and its evolution was quantified and analyzed.

36 MATERIALS SCIENCE↗

Structure disorder degree of polysilicon thin films grown by different processing: Constant C from Raman spectroscopy

Flat, low-stress, boron-doped polysilicon thin films were prepared on single crystalline silicon substrates by low pressure chemical vapor deposition. It was found that the polysilicon films with different deposition processing have different microstructure properties. The confinement effect, tensile stresses, defects, and the Fano effect all have a great influence on the line shape of Raman scattering peak. But the effect results are different. The microstructure and the surface layer are two important mechanisms dominating the internal stress in three types of polysilicon thin films. For low-stress polysilicon thin film, the tensile stresses are mainly due to the change of microstructure after thermal annealing. But the tensile stresses in flat polysilicon thin film are induced by the silicon carbide layer at surface. After the thin film doped with boron atoms, the phenomenon of the tensile stresses increasing can be explained by the change of microstructure and the increase in the content of silicon carbide. We also investigated the disorder degree states for three polysilicon thin films by analyzing a constant C. It was found that the disorder degree of low-stress polysilicon thin film larger than that of flat and boron-doped polysilicon thin films due to the phase transformation after annealing. After the flat polysilicon thin film doped with boron atoms, there is no obvious change in the disorder degree and the disorder degree in some regions even decreases.

36 MATERIALS SCIENCE↗

Surface state dominated transport in topological insulator Bi{sub 2}Te{sub 3} nanowires

We report on low temperature magnetoresistance measurements on single-crystalline Bi{sub 2}Te{sub 3} nanowires synthesized via catalytic growth and post-annealing in a Te-rich atmosphere. The observation of Aharonov-Bohm oscillations indicates the presence of topological surface states. Analyses of Subnikov-de Haas oscillations in perpendicular magnetoresistance yield extremely low two-dimensional carrier concentrations and effective electron masses, and very high carrier mobilities. All our findings are in excellent agreement with theoretical predictions of massless Dirac fermions at the surfaces of topological insulators.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of carrier density and valence states on superconductivity of oxygen annealed Fe{sub 1.06}Te{sub 0.6}Se{sub 0.4} single crystals

The variations of carrier density and valence states in oxygen annealed Fe{sub 1.06}Te{sub 0.6}Se{sub 0.4} single crystals were studied systematically. It was found that the carrier density n{sub H} increases after oxygen annealing by Hall coefficient measurements. The X-ray photoelectron spectroscopy experiments reveal that the oxygen annealing changes Fe{sup 0} and Te{sup 0} states to Fe{sup 2+/3+} and Te{sup 4+}, respectively, while the valence variation of Se is negligible. Our results indicate that the improvement of superconductivity, such as the zero resistance transition temperature T{sub c}{sup zero}, shielding and Meissner fraction value 4πχ and upper critical field H{sub c2}, could be closely related to the proper manipulation of n{sub H} and the valence states by oxygen annealing in the system.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Sputtering of Si, SiC, InAs, InP, Ge, GaAs, GaSb, and GaN by electrosprayed nanodroplets

This article presents a characterization of the damage caused by energetic beams of electrosprayed nanodroplets striking the surfaces of single-crystal semiconductors including Si, SiC, InAs, InP, Ge, GaAs, GaSb, and GaN. The sputtering yield (number of atoms ejected per projectile's molecule), sputtering rate, and surface roughness are measured as functions of the beam acceleration potential. The maximum values of the sputtering yields range between 1.9 and 2.2 for the technological important but difficult to etch SiC and GaN respectively, and 4.5 for Ge. The maximum sputtering rates for the non-optimized beam flux conditions used in our experiments vary between 409 nm/min for SiC and 2381 nm/min for GaSb. The maximum sputtering rate for GaN is 630 nm/min. Surface roughness increases modestly with acceleration voltage, staying within 2 nm and 20 nm for all beamlet acceleration potentials and materials except Si. At intermediate acceleration potentials, the surface of Si is formed by craters orders of magnitude larger than the projectiles, yielding surface roughness in excess of 60 nm. The effect of projectile dose is studied in the case of Si. This parameter is correlated with the formation of the large craters typical of Si, which suggests that the accumulation of damage following consecutive impacts plays an important role in the interaction between beamlet and target.

36 MATERIALS SCIENCE↗

Phase change in terahertz waves emitted from differently doped graphite: The role of carrier drift

We investigate characteristics of THz waves radiated from differently doped graphite samples excited by femtosecond laser pulses. Between n-type single-crystalline graphite and p-type polycrystalline graphite films, we observe the phase reversal of THz waves regardless of excitation energy variations around K-valley. In addition, variations in other parameters such as excitation fluence and azimuthal angle produce no changes in the phase of THz waves, which correlate well with the opposite dipole polarization between differently doped samples rather than unidirectional diffusive transport.

36 MATERIALS SCIENCE↗

Distributions of methyl group rotational barriers in polycrystalline organic solids

We bring together solid state {sup 1}H spin-lattice relaxation rate measurements, scanning electron microscopy, single crystal X-ray diffraction, and electronic structure calculations for two methyl substituted organic compounds to investigate methyl group (CH{sub 3}) rotational dynamics in the solid state. Methyl group rotational barrier heights are computed using electronic structure calculations, both in isolated molecules and in molecular clusters mimicking a perfect single crystal environment. The calculations are performed on suitable clusters built from the X-ray diffraction studies. These calculations allow for an estimate of the intramolecular and the intermolecular contributions to the barrier heights. The {sup 1}H relaxation measurements, on the other hand, are performed with polycrystalline samples which have been investigated with scanning electron microscopy. The {sup 1}H relaxation measurements are best fitted with a distribution of activation energies for methyl group rotation and we propose, based on the scanning electron microscopy images, that this distribution arises from molecules near crystallite surfaces or near other crystal imperfections (vacancies, dislocations, etc.). An activation energy characterizing this distribution is compared with a barrier height determined from the electronic structure calculations and a consistent model for methyl group rotation is developed. The compounds are 1,6-dimethylphenanthrene and 1,8-dimethylphenanthrene and the methyl group barriers being discussed and compared are in the 2–12 kJ mol{sup −1} range.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Realization of single-termination SrTiO{sub 3} (100) surfaces by a microwave-induced hydrothermal process

A microwave-induced hydrothermal etching of SrTiO{sub 3} (100) single crystal surfaces in deionized water and subsequent annealing in oxygen atmosphere results in single-terminated and atomically flat terraces for pure and niobium-doped substrates as confirmed through one unit-cell step height and uniform phase by atomic force microscopy. This process that requires 3 min of moderate microwave radiation completely avoids the use of hydrofluoric acid (HF) and related point defects due to fluorine in the crystal surface. The advantages of a safe, inexpensive, and environmentally neutral process hold promise to replace the existing standard protocol for substrate preparation based on buffered HF.

36 MATERIALS SCIENCE↗

Electronic band structure imaging of three layer twisted graphene on single crystal Cu(111)

Few layer graphene (FLG) is grown on single crystal Cu(111) by Chemical Vapor Deposition, and the electronic valence band structure is imaged by Angle-Resolved Photo-Emission Spectroscopy. It is found that graphene essentially grows polycrystalline. Three nearly ideal Dirac cones are observed along the Cu Γ{sup ¯}K{sup ¯} direction in k-space, attributed to the presence of ∼4° twisted three layer graphene with negligible interlayer coupling. The number of layers and the stacking order are compatible with Raman data analysis demonstrating the complementarity of the two techniques for a more accurate characterization of FLG.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Adsorption calorimetry during metal vapor deposition on single crystal surfaces: Increased flux, reduced optical radiation, and real-time flux and reflectivity measurements

Thin films of metals and other materials are often grown by physical vapor deposition. To understand such processes, it is desirable to measure the adsorption energy of the deposited species as the film grows, especially when grown on single crystal substrates where the structure of the adsorbed species, evolving interface, and thin film are more homogeneous and well-defined in structure. Our group previously described in this journal an adsorption calorimeter capable of such measurements on single-crystal surfaces under the clean conditions of ultrahigh vacuum [J. T. Stuckless, N. A. Frei, and C. T. Campbell, Rev. Sci. Instrum. 69, 2427 (1998)]. Here we describe several improvements to that original design that allow for heat measurements with ∼18-fold smaller standard deviation, greater absolute accuracy in energy calibration, and, most importantly, measurements of the adsorption of lower vapor-pressure materials which would have previously been impossible. These improvements are accomplished by: (1) using an electron beam evaporator instead of a Knudsen cell to generate the metal vapor at the source of the pulsed atomic beam, (2) changing the atomic beam design to decrease the relative amount of optical radiation that accompanies evaporation, (3) adding an off-axis quartz crystal microbalance for real-time measurement of the flux of the atomic beam during calorimetry experiments, and (4) adding capabilities for in situ relative diffuse optical reflectivity determinations (necessary for heat signal calibration). These improvements are not limited to adsorption calorimetry during metal deposition, but also could be applied to better study film growth of other elements and even molecular adsorbates.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Enhanced ferroelectric properties and thermal stability of nonstoichiometric 0.92(Na{sub 0.5}Bi{sub 0.5})TiO{sub 3}-0.08(K{sub 0.5}Bi{sub 0.5})TiO{sub 3} single crystals

Bi deficient, Mn doped 0.92(Na{sub 0.5}Bi{sub 0.5})TiO{sub 3}-0.08(K{sub 0.5}Bi{sub 0.5})TiO{sub 3} single crystals were grown by carefully controlled top-seeded solution growth method. Local structures were investigated by transmission electron microscopy. The site occupation and valence state of manganese were characterized by electron paramagnetic resonance spectrum. The leakage current density in the as-grown single crystals is effectively depressed. The introduced defect complexes suppress the temperature induced phase transformation, increasing the depolarization temperature (165 °C) and thermal stability of ferroelectric properties.

36 MATERIALS SCIENCE↗