Search NASA⌕ Search

SEARCH · Search NASA

Results for “Material Point Method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Dynamic Tensile Characterization of Thin-Sheet Brittle Metallic Materials

Refractory metals are favorable materials in applications where high strength and ductility are needed at elevated temperatures. In some cases, operating temperatures may be near the melting point of the material. However, as temperature drops, refractory metals typically undergo a significant mechanical response change - ductile-to-brittle transition. These materials may be subjected to high strain rate loading at an ambient temperature state, such as an impact or crash. Knowledge of the high rate material properties are essential for design as well as simulation of impact events. The high rate stress-strain behavior of brittle metallic materials at ambient temperature is rarely studied because of experimental challenges, particularly when failure is involved. Failure typically occurs within the non-gage section of the material, which invalidates any collected stress-strain information. Here, a method to determine a specimen geometry which will produce failures in the gage section is presented. Pure tungsten in thin-sheet form was used as a trial material to select a specimen geometry for high rate Kolsky tension bar experiments. A finite element simulation was conducted to derive a strain correction for more accurate results. The room temperature stress-strain behavior of pure tungsten at a strain rate of 24 s –1 is presented. The outcome of this experimental technique can be applied to other brittle materials for dynamic tensile characterization.

36 MATERIALS SCIENCE↗

Subclinical Cardiotoxicity Detected by Strain Rate Imaging up to 14 months After Breast Radiation Therapy

Purpose: Strain rate imaging (SRI) is a new echocardiographic modality that enables accurate measurement of regional myocardial function. We investigated the role of SRI and troponin I (TnI) in the detection of subclinical radiation therapy (RT)-induced cardiotoxicity in breast cancer patients. Methods and Materials: This study prospectively included 75 women (51 left-sided and 24 right-sided) receiving adjuvant RT to the breast/chest wall and regional lymph nodes. Sequential echocardiographs with SRI were obtained before RT, immediately after RT, and 8 and 14 months after RT. TnI levels were measured on the first and last day of RT. Results: Mean heart and left ventricle (LV) doses were both 9 ± 4 Gy for the left-sided patients and 4 ± 4 Gy and 1 ± 0.4 Gy, respectively, for the right-sided patients. A decrease in strain was observed at all post-RT time points for left-sided patients (−17.5% ± 1.9% immediately after RT, −16.6% ± 1.4% at 8 months, and −17.7% ± 1.9% at 14 months vs −19.4% ± 2.4% before RT, P<.01) but not for right-sided patients. When we considered left-sided patients only, the highest mean dose was given to the anterior left ventricular (LV) wall (25 ± 14 Gy) and the lowest to the inferior LV wall (3 ± 3 Gy). Strain of the anterior wall was reduced after RT (−16.6% ± 2.3% immediately after RT, −16% ± 2.6% at 8 months, and −16.8% ± 3% at 14 months vs −19% ± 3.5% before RT, P<.05), whereas strain of the inferior wall showed no significant change. No changes were observed with conventional echocardiography. Furthermore, mean TnI levels for the left-sided patients were significantly elevated after RT compared with before RT, whereas TnI levels of the right-sided patients remained unaffected. Conclusions: In contrast to conventional echocardiography, SRI detected a regional, subclinical decline in cardiac function up to 14 months after breast RT. It remains to be determined whether these changes are related to clinical outcome. In the meantime, we encourage the use of radiation techniques that minimize the exposure of the anterior LV wall in left-sided patients.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Crystal structure and electron density in the apatite-type ionic conductor La{sub 9.71}(Si{sub 5.81}Mg{sub 0.18})O{sub 26.37}

Crystal structure and electron density in the apatite-type ionic conductor La{sub 9.71}(Si{sub 5.81}Mg{sub 0.18})O{sub 26.37} have been investigated at 302, 674 and 1010 K by Rietveld refinement and a whole-pattern fitting approach based on the maximum-entropy method (MEM) using synchrotron X-ray powder diffraction data. Second harmonic generation measurements indicated that the space group of this material is centrosymmetric. Among the possible hexagonal groups P6{sub 3}/m, P6{sub 3} and P3-bar the former is correct for La{sub 9.71}(Si{sub 5.81}Mg{sub 0.18})O{sub 26.37}. Rietveld refinements suggested an oxygen interstitial site (0.03,0.15,0.85) near the hexagonal axis. MEM analyses revealed that the Si{sub 0.97}Mg{sub 0.03} atom has covalent bonds with four adjacent oxygen atoms to form a tetrahedron. The oxygen O4 atom located at the 2a site (0.0,0.0,1/4) exhibited large atomic displacement parameters along the c axis and electron density mapping also indicated the wide distribution consistent with migration of oxygen ions in this direction. - Graphical abstract: Equielectron density surfaces at 1.0 A{sup -3} of apatite-type La{sub 9.71}(Si{sub 5.81}Mg{sub 0.18})O{sub 26.37} at 302 K. O4 atoms have large distribution along the <001> direction (white arrows).

36 MATERIALS SCIENCE↗

Synthesis, electronic transport and magnetic properties of Zr{sub 1-x}Y{sub x}NiSn, (x=0-0.25) solid solutions

The crystal structure of the Zr{sub 1-x}Y{sub x}NiSn half-Heusler solid solutions is synthesized and their crystal structure is determined. Electrical resistivity and thermoelectric Seebeck coefficient are measured in the 80-380 K temperature range, whereas magnetic susceptibility is measured at 290 K. It is established that substitution of Zr host atoms by Y in the ZrNiSn intermetallic semiconductor is equivalent to doping by acceptor impurities. Self-consistent ab initio calculations, based on the full potential local orbital (FPLO) minimum basis method, are performed to investigate the electronic and thermoelectric properties of these alloys. Spin polarized within the framework of the coherent potential approximation (CPA) are included. - Graphical abstract: Both approaches experimental and calculations point to the same conclusions. Resistivity and thermopower measurements assert that doping of ZrNiSn based compound by the Y as acceptor impurity induces the insulator-metal transition and leads the S value sign reverse.

36 MATERIALS SCIENCE↗

Quantifying the distribution of paste-void spacing of hardened cement paste using X-ray computed tomography

The distribution of paste-void spacing in cement-based materials is an important feature related to the freeze-thaw durability of these materials, but its reliable estimation remains an unresolved problem. Herein, we evaluate the capability of X-ray computed tomography (CT) for reliable quantification of the distribution of paste-void spacing. Using X-ray CT images of three mortar specimens having different air-entrainment characteristics, we calculate the distributions of paste-void spacing of the specimens by applying previously suggested methods for deriving the exact spacing of air-void systems. This methodology is assessed by comparing the 95th percentile of the cumulative distribution function of the paste-void spacing with spacing factors computed by applying the linear-traverse method to 3D air-void system and reconstructing equivalent air-void distribution in 3D. Results show that the distributions of equivalent void diameter and paste-void spacing follow lognormal and normal distributions, respectively, and the ratios between the 95th percentile paste-void spacing value and the spacing factors reside within the ranges reported by previous numerical studies. This experimental finding indicates that the distribution of paste-void spacing quantified using X-ray CT has the potential to be the basis for a statistical assessment of the freeze-thaw durability of cement-based materials. - Highlights: Black-Right-Pointing-Pointer The paste-void spacing in 3D can be quantified by X-ray CT. Black-Right-Pointing-Pointer The distribution of the paste-void spacing follows normal distribution. Black-Right-Pointing-Pointer The spacing factor and 95th percentile of CDF of paste-void spacing are correlated.

36 MATERIALS SCIENCE↗

Combinatorial Exploration and Mapping of Phase Transformation in a Ni–Ti–Co Thin Film Library

Combinatorial synthesis and high-throughput characterization of a Ni–Ti–Co thin film materials library are reported for exploration of reversible martensitic transformation. The library was prepared by magnetron co-sputtering, annealed in vacuum at 500 °C without atmospheric exposure, and evaluated for shape memory behavior as an indicator of transformation. Composition, structure, and transformation behavior of the 177 pads in the library were characterized using high-throughput wavelength dispersive spectroscopy (WDS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and four-point probe temperature-dependent resistance (R(T)) measurements. A new, expanded composition space having phase transformation with low thermal hysteresis and Co > 10 at. % is found. Unsupervised machine learning methods of hierarchical clustering were employed to streamline data processing of the large XRD and XPS data sets. Through cluster analysis of XRD data, we identified and mapped the constituent structural phases. Finally, composition–structure–property maps for the ternary system are made to correlate the functional properties to the local microstructure and composition of the Ni–Ti–Co thin film library.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Local doping of graphene devices by selective hydrogen adsorption

N-type graphene fabricated by exposure to hydrogen gas has been previously studied. Based on this property of graphene, herein, we demonstrate local doping in single-layer graphene using selective adsorption of dissociative hydrogen at 350 K. A graphene field effect transistor was produced covered with PMMA on half of the graphene region. The charge neutrality point of the PMMA-window region shifted to a negative gate voltage (V{sub G}) region prominently compared with that of the PMMA-covered region. Consequently, a single graphene p-n junction was obtained by measuring the V{sub G}-dependent resistance of the whole graphene region. This method presents opportunities for developing and controlling the electronic structure of graphene and device applications.

36 MATERIALS SCIENCE↗

Structural crossover in a supercooled metallic liquid and the link to a liquid-to-liquid phase transition

Time-resolved synchrotron measurements were carried out to capture the structure evolution of an electrostatically levitated metallic-glass-forming liquid during free cooling. The experimental data shows a crossover in the liquid structure at ~1000 K, about 115 K below the melting temperature and 150 K above the crystallization temperature. The structure change is characterized by a dramatic growth in the extended-range order below the crossover temperature. Molecular dynamics simulations have identified that the growth of the extended-range order was due to an increased correlation between solute atoms. These results provide structural evidence for a liquid-to-liquid-phase-transition in the supercooled metallic liquid.

Glass transitions↗

Growing intermetallic single crystals using in situ decanting

High temperature metallic solution growth is one of the most successful and versatile methods for single crystal growth, and is particularly suited for exploratory synthesis. The method commonly utilizes a centrifuge at room temperature and is very successful for the synthesis of single crystal phases that can be decanted from the liquid below the melting point of the silica ampoule. In this paper, we demonstrate the extension of this method that enables single crystal growth and flux decanting inside the furnace at temperatures above 1200°C. This not only extends the number of available metallic solvents that can be used in exploratory crystal growth but also can be particularly well suited for crystals that have a rather narrow exposed solidification surface in the equilibrium alloy phase diagram.

36 MATERIALS SCIENCE↗

Dependence on pressure of the refractive indices of wurtzite ZnO, GaN, and AlN

We have measured both the ordinary and extraordinary refractive index of m-plane cuts of wurtzite ZnO, GaN, and AlN single crystals at room temperature and as a function of hydrostatic pressure up to 8 GPa. For that purpose we have developed an alternative optical interference method, called bisected-beam method, which leads, in general, to high contrast interference fringes. Its main feature, however, is to be particularly suitable for high pressure experiments with the diamond anvil cell, when the refractive index of the sample is low and similar to that of diamond and/or the pressure transmitting medium, as is the case here. For all three wide-gap materials we observe a monotonous decrease of the ordinary and extraordinary refractive indices with increasing pressure, being most pronounced for GaN, less marked for ZnO, and the smallest for AlN. The frequency dependence of the refractive indices was extrapolated to zero energy using a critical-point-plus-Lorentz-oscillator model of the ordinary and extraordinary dielectric function. In this way, we determined the variation with pressure of the electronic part (no-phonon contribution) of the static dielectric constant epsilon(infinity). Its volume derivative, r = d ln epsilon(infinity)/d ln V, serves as single scaling coefficient for comparison with experimental and/or theoretical results for other semiconductors, regarding the pressure effects on the dielectric properties. We have obtained an ordinary/extraordinary average value (r) over bar of 0.49(15) for ZnO, 1.22(9) for GaN, and 0.32(4) for AlN. With the values for the ordinary and extraordinary case being within experimental uncertainty, there is thus no apparent change in dielectric anisotropy under pressure for these wurtzite semiconductors. Results are discussed in terms of the pressure-dependent electronic band structure of the materials.

Goni, AR↗

Monte Carlo Simulations of Crystal Defects in Open Ensembles

Zero- and two-dimensional crystal defects form in open statistical ensembles, such as the grand canonical, that are usually inaccessible with conventional simulation techniques. This longstanding challenge is overcome with a new Hamiltonian Monte Carlo method that samples energy-biased gradual transformations. In conclusion, the method enables free energy calculations for nonideal point defects and the direct prediction of finite-temperature interface structures.

Grain boundaries↗

Visualization of Dynamic Vortex Structures in Magnetic Films with Uniaxial Anisotropy (Micromagnetic Simulation)

Three-dimensional computer simulation of dynamic processes in a moving domain boundary separating domains in a soft magnetic uniaxial film with planar anisotropy is performed by numerical solution of Landau-Lifshitz-Gilbert equations. The developed visualization methods are used to establish the connection between the motion of surface vortices and antivortices, singular (Bloch) points, and core lines of intrafilm vortex structures. A relation between the character of magnetization dynamics and the film thickness is found. The analytical models of spatial vortex structures for imitation of topological properties of the structures observed in micromagnetic simulation are constructed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Cohesive Zone Modeling in Geomaterial

The purpose of the two projects discussed in this report is to use the cohesive zone method to evaluate fracture properties of geomaterials. Two experimental tests, the push-out test and the notched three-point bend test, were modeled computationally using finite element analysis and cohesive zone modeling to extract load and displacement information and ultimately determine failure behavior. These results are to be compared with experimental tests when they are available. The first project used the push-out test to investigate the shear bond strength at the cement- shale interface. The second project explored the effects of scaling a notched three-point bending specimen to study fracture toughness characteristics. The bond strength and fracture toughness of a material and its interfaces are important parameters to consider in subsurface applications so that zonal isolation can be achieved.

42 ENGINEERING↗

Evaluation of Attila and MCNP computational methods for dose and exposure estimation

Radiation transport calculations are often used to estimate dose or exposure to components and personnel surrounding a radiation source. The sources for these calculations are decaying radionuclides within various nuclear materials. Historically, dose calculations use MCNP (Monte Carlo N-Particle) transport code as the primary particle transport tool without a secondary computational tool to validate the results from the MCNP simulations [1]. The goal of this study is to make an independent check of the Monte Carlo solution from MCNP6 Version 6.2.1 with the discrete ordinates solution from Attila 10.2.0 Beta 3. As an example problem for this study, water-filled, stainless-steel vessels, modeled with an unstructured mesh (UM) with both MCNP and Attila [2], are exposed to 252Cf and 60Co point sources. This report also includes a discussion of the limitations of unstructured mesh in a MCNP calculation.

61 RADIATION PROTECTION AND DOSIMETRY↗

Hydrothermal synthesis and luminescent properties of NaLa(MoO{sub 4}){sub 2}:Dy{sup 3+} phosphor

Pompon-like NaLa(MoO{sub 4}){sub 2}:Dy{sup 3+} phosphors have been successfully prepared via a hydrothermal method using ammonia as pH value regulator. The hydrothermal process was carried out under aqueous condition without the use of any organic solvent, surfactant, and catalyst. The experimental results demonstrate that the obtained NaLa(MoO{sub 4}){sub 2}:Dy{sup 3+} phosphor powders are single-phase scheelite structure with tetragonal symmetry. Moreover, the phosphor under the excitation of 390 and 456 nm exhibited blue emission (486 nm) and yellow emission (574 nm), corresponding to the {sup 4}F{sub 9/2}{yields}{sup 6}H{sub 15/2} transition and {sup 4}F{sub 9/2}{yields}{sup 6}H{sub 13/2} transition of Dy{sup 3+} ions, respectively. In addition, the yellow-to-blue emission intensity ratio (Y/B) can be changed with the doped concentration of Dy{sup 3+} ions. All chromaticity coordinates of the obtained NaLa(MoO{sub 4}){sub 2}:Dy{sup 3+} phosphors are located in the white-light region. The results indicate that this kind of phosphor may has potential applications in the fields of near UV-excited and blue-excited white LEDs. - Graphical abstract: It can be seen from the SEM images that a pompon-like shape was obtained with an average diameter of about 1 {mu}m, and it is composed of many nanoflakes. Highlights: Black-Right-Pointing-Pointer Pompon-like NaLa(MoO{sub 4}){sub 2}:Dy{sup 3+} phosphors have been successfully prepared via a hydrothermal method. Black-Right-Pointing-Pointer Blue emission at 486 nm and yellow emission at 574 nm were obtained from the samples. Black-Right-Pointing-Pointer The yellow-to-blue emission intensity ratio (Y/B) can be changed with the doped concentration of Dy{sup 3+} ions. Black-Right-Pointing-Pointer NaLa(MoO{sub 4}){sub 2}:Dy{sup 3+} can be efficiently excited by the blue light and the near ultraviolet light.

36 MATERIALS SCIENCE↗

Nonlinear Resonance Response of Porous Beam-Type Implants Corresponding to Various Morphology Shapes for Bone Tissue Engineering Applications

Having excellent biocompatibility and apatite mineralization as well as efficient mechanical properties makes bredigite as one of the most attractive bioceramics. A beam-type porous biological implant in a 3D-printed architecture is designed with micron pore size. The surface properties, morphology, and size of the composed powders are evaluated using Scherrer and Williamson-Hall equation. The effect of MNPs deposition into the bredigite bioceramics and correlation with temperature effect on roughness of the prepared bio-nanocomposite are also investigated for hyperthermia application potential. The composed powders are characterized by x-ray diffraction, and then scanning electron microscopy (SEM), differential scanning calorimetry, thermogravimetric analysis (weight change, TGA), and atomic force microscopy are utilized to evaluate the surface topography. The resonance response is the tendency of a bone scaffold to respond at prominent amplitude while the frequency of its oscillations is equal to the structure’s natural frequency of vibration. Therefore, based on the obtained mechanical properties via the experimental approach for the bio-nanocomposite material, an analytical solution based upon the multiple-timescale method is carried out to analyze the nonlinear primary resonance of a 3D-printed porous beam-type biological implant under uniform-distributed load. According to SEM observations, there are hard agglomerates in the bredigite-magnetite nanoparticles (Br-MNPs) bio-nanocomposite material with low weight fraction of MNPs. However, they are broken down by increasing the amount of MNPs. Also, it is displayed that for lower MNPs weight fraction, the height of jump phenomenon related to the nonlinear resonance response is maximum and minimum for, respectively, irregular and mesoporous shapes of morphology, but their associated forcing amplitudes related to the bifurcation points are minimum and maximum, respectively.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Using molecular dynamics to predict the solidus and liquidus of mixed oxides ( Th , U ) O 2 , ( Th , Pu ) O 2 and ( Pu , U ) O 2

Molecular dynamics (MD) was used to establish a mechanistic basis for the experimentally observed reduction in liquidus and solidus temperatures below the melting point of the end-members for the mixed oxides (Th,U)O 2 , (Th, Pu) O 2 and (Pu, U) O 2 . This dip is found at additions of the oxide with higher melting point to the oxide with the lower melting point. There are many causes suggested for the dip; here the distribution of the cation Frenkel energy for the mixed oxides caused by the local environment is proposed as a contributor. Furthermore, a variant of the moving interface method which yields information on the position of the solidus and liquidus boundaries, is used to predict the phase diagrams of these systems.

36 MATERIALS SCIENCE↗

Evidence for nitrogen binding to surface defects for topological insulator Bi 2 Se 3

Using scanning tunneling spectroscopy and theoretical simulations we have studied the effects of nitrogen gas exposure on the electronic density of states of Bi 2 Se 3 , a well-studied topological insulator. In carefully controlled measurements, Bi 2 Se 3 crystals were initially cleaved in a helium gas environment and then exposed to a 22 SCFH flow of ultra-high purity N 2 gas. We observe a resulting change in the spectral curves, with the exposure effect saturating after approximately 50 min, ultimately bringing the Dirac point about 50 meV closer to the Fermi level. Furthermore, these results are compared to density functional theory calculations, which support a picture of N 2 molecules physisorbing near Se vacancies. Furthermore, ab initio molecular dynamics simulations aided by a Blue Moon ensemble method reveal the dissociative adsorption of N 2 molecules which then bind strongly to Se vacancies at the surface. In this scenario, the binding of the N atom to a Se vacancy site removes the surface defect state created by the vacancy and changes the position of the Fermi energy with respect to the Dirac point.

36 MATERIALS SCIENCE↗