Search NASA⌕ Search

SEARCH · Search NASA

Results for “Simulation System”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Simulation evaluation of the advanced control concept for the NASA V/STOL research aircraft (VSRA)

Two candidate control systems for the Vertical/Short Takeoff and Landing (V/STOL) Research Aircraft (VSRA) are described, both of which are limited-authority, digital, fly-by wire variants of the original YAV-8B Harrier control system. The performance of these systems was compared with that of an ideal, full-authority system in simulated, adverse-weather V/STOL shipboard operations using the Ames Research Center's Vertical Motion Simulator. Both systems showed some performance degradation relative to the ideal, but both were adequate to meet VSRA program objectives. The favored system, selected because of safety considerations, was further simulated using a precision visual hovering task that verified its acceptability.

Moralez, E.↗

Thermodynamic Vent System Test in a Low Earth Orbit Simulation

A thermodynamic vent system for a cryogenic nitrogen tank was tested in a vacuum chamber simulating oxygen storage in low earth orbit. The nitrogen tank was surrounded by a cryo-shroud at -40 F. The tank was insulated with two layers of multi-layer insulation. Heat transfer into cryogenic tanks causes phase change and increases tank pressure which must be controlled. A thermodynamic vent system was used to control pressure as the location of vapor is unknown in low gravity and direct venting would be wasteful. The thermodynamic vent system consists of a Joule-Thomson valve and heat exchanger installed on the inlet side of the tank mixer-pump. The combination is used to extract thermal energy from the tank fluid, reducing temperature and ullage pressure. The system was sized so that the tank mixer-pump operated a small fraction of the time to limit motor heating. Initially the mixer used sub-cooled liquid to cool the liquid-vapor interface inducing condensation and pressure reduction. Later, the thermodynamic vent system was used. Pressure cycles were performed until steady-state operation was demonstrated. Three test runs were conducted at tank fills of 97, 80, and 63 percent. Each test was begun with a boil-off test to determine heat transfer into the tank. The lower tank fills had time averaged vent rates very close to steady-state boil-off rates showing the thermodynamic vent system was nearly as efficient as direct venting in normal gravity.

VanOverbeke, Thomas J.↗

Data analysis study and performance evaluation of the scanning laser Doppler system

A simulation program which provided information on theoretically expected vortex spectra, evaluations of potential algorithms, and expected location accuracies for given scan patterns is presented. Field tests using an aircraft engine flow field and aircraft vortices during flyby tests were compared to the results of the simulation. From these studies, a vortex location algorithm was developed which provided vortex location for one or two vortices as a function of time. Results of this algorithm used on data from flyby tests were used to study vortex transport, to evaluate system performance, and to provide suggestions for real-time vortex location algorithms. The results of real-time analysis were compared to those which were expected based on theoretical considerations.

Sonnenschein, C. M.↗

Entry, Descent and Landing Systems Analysis: Exploration Class Simulation Overview and Results

NASA senior management commissioned the Entry, Descent and Landing Systems Analysis (EDL-SA) Study in 2008 to identify and roadmap the Entry, Descent and Landing (EDL) technology investments that the agency needed to make in order to successfully land large payloads at Mars for both robotic and exploration or human-scale missions. The year one exploration class mission activity considered technologies capable of delivering a 40-mt payload. This paper provides an overview of the exploration class mission study, including technologies considered, models developed and initial simulation results from the EDL-SA year one effort.

DwyerCianciolo, Alicia M.↗

SIRIUS: Simulation Infrastructure for Research on Interoperating Unmanned Systems

This paper presents the Simulation Infrastructure for Research on Interoperating Unmanned Systems (SIRIUS), a research framework for simulation and analysis of future conceptual Urban Air Mobility (UAM) operations. SIRIUS is being developed under the auspices of the NASA Air Traffic Management eXploration project, UAM subproject (ATM-X UAM). SIRIUS provides an intuitive, highly configurable graphical user interface to design complex traffic scenarios and airspace configurations representative of conceptual UAM operations. Aircraft simulated with SIRIUS can be equipped with flight-tested capabilities for detect and avoid (DAA), geofencing, distributed merging and spacing, path conformance, and path planning while executing time-constrained, 4D trajectories generated by a UAM ground operations system. Central to the design of the SIRIUS simulation framework is the capability to evaluate the integration and interoperability of ground-based separation services (e.g., strategic separation) with extended DAA functionality (e.g., path monitoring, separation provision, merging and spacing, etc.) The simulation environment also supports modelling of wind, navigation, and sensor uncertainties, as well as communication delays. SIRIUS enables distributed simulation of large-scale scenarios. An interactive graphical analysis capability helps isolate, visualize, and compare relevant vehicle state data and widely used measures of performance metrics across multiple scenarios.

Andrew Peters↗

Development of an adaptive failure detection and identification system for detecting aircraft control element failures

A methodology for designing a failure detection and identification (FDI) system to detect and isolate control element failures in aircraft control systems is reviewed. An FDI system design for a modified B-737 aircraft resulting from this methodology is also reviewed, and the results of evaluating this system via simulation are presented. The FDI system performed well in a no-turbulence environment, but it experienced an unacceptable number of false alarms in atmospheric turbulence. An adaptive FDI system, which adjusts thresholds and other system parameters based on the estimated turbulence level, was developed and evaluated. The adaptive system performed well over all turbulence levels simulated, reliably detecting all but the smallest magnitude partially-missing-surface failures.

Bundick, W. Thomas↗

An Approach for Utilizing Power Flow Modeling for Simulations of Hybrid Electric Propulsion Systems

This paper describes an approach to creating simulations of the electric components for a hybrid electric propulsion system. The proposed modeling technique is based on power/load flow modeling and is designed to provide a modular framework that includes buses, lines, and other electrical components that can be connected together to form the electrical distribution system. The purpose of this paper is to detail an electric distribution system modeling technique and to demonstrate how these models may be integrated with turbomachinery simulations. These general modeling techniques were created to be utilized for system and control design studies. Additionally, steady-state and dynamic performance for a proposed model example is compared with data from a hardware in the loop simulation.

Chapman, Jeffryes W.↗

Low-g simulation testing of propellant systems using neutral buoyancy

A two liquid, neutral buoyancy technique is being used to simulate propellant behavior in a weightless environment. By equalizing the density of two immiscible liquids within a container (propellant tank), the effect of gravity at the liquid interface is balanced. Therefore the surface-tension forces dominate to control the liquid/liquid system configuration in a fashion analogous to a liquid/gas system in a zero gravity environment.

Balzer, D. L.↗

Evaluating Performance of UAS Detect-And-Avoid System Using a Fast-Time Simulation Tool

Most unmanned aircraft systems will be required to be equipped with a Detect-and-Avoid (DAA) system. The surveillance performance of the DAA system to detect and track intruder aircraft will depend on the encounter geometries that unmanned aircraft are expected to have with other aircraft in the airspace. The performance of DAA alerting and avoidance system is also dependent on the timeliness of alerting for UAS pilots to give a sufficient time to determine and command a resolution maneuver to avoid well clear separation violations. This presentation introduces general background of UAS DAA systems and concept of well clear separation standard to satisfy see and avoid regulations. The presentation shows the several UAS mission profiles and analysis of the encounter geometries that were simulated using historical VFR traffic data and some proposed UAS missions. This presentation introduces several potential metrics for evaluating the performance of a DAA system and shows the results that measured through fast-time simulation with traffic scenarios that include NAS-wide VFR manned aircraft and IFR UAS flights. At the end, some research areas will be briefly discussed.

UAS↗

A simulation of the instrument pointing system for the Astro-1 mission

NASA has recently completed a shuttle-borne stellar ultraviolet astronomy mission known as Astro-1. A three axis instrument pointing system (IPS) was employed to accurately point the science instruments. In order to analyze the pointing control system and verify pointing performance, a simulation of the IPS was developed using the multibody dynamics software TREETOPS. The TREETOPS IPS simulation is capable of accurately modeling the multibody IPS system undergoing large angle, nonlinear motion. The simulation is documented and example cases are presented demonstrating disturbance rejection, fine pointing operations, and multiple target pointing and slewing of the IPS.

Whorton, M.↗

Extraction and Separation Modeling of Orion Test Vehicles with ADAMS Simulation

The Capsule Parachute Assembly System (CPAS) project has increased efforts to demonstrate the performance of fully integrated parachute systems at both higher dynamic pressures and in the presence of wake fields using a Parachute Compartment Drop Test Vehicle (PCDTV) and a Parachute Test Vehicle (PTV), respectively. Modeling the extraction and separation events has proven challenging and an understanding of the physics is required to reduce the risk of separation malfunctions. The need for extraction and separation modeling is critical to a successful CPAS test campaign. Current PTV-alone simulations, such as Decelerator System Simulation (DSS), require accurate initial conditions (ICs) drawn from a separation model. Automatic Dynamic Analysis of Mechanical Systems (ADAMS), a Commercial off the Shelf (COTS) tool, was employed to provide insight into the multi-body six degree of freedom (DOF) interaction between parachute test hardware and external and internal forces. Components of the model include a composite extraction parachute, primary vehicle (PTV or PCDTV), platform cradle, a release mechanism, aircraft ramp, and a programmer parachute with attach points. Independent aerodynamic forces were applied to the mated test vehicle/platform cradle and the separated test vehicle and platform cradle. The aero coefficients were determined from real time lookup tables which were functions of both angle of attack ( ) and sideslip ( ). The atmospheric properties were also determined from a real time lookup table characteristic of the Yuma Proving Grounds (YPG) atmosphere relative to the planned test month. Representative geometries were constructed in ADAMS with measured mass properties generated for each independent vehicle. Derived smart separation parameters were included in ADAMS as sensors with defined pitch and pitch rate criteria used to refine inputs to analogous avionics systems for optimal separation conditions. Key design variables were dispersed in a Monte Carlo analysis to provide the maximum expected range of the state variables at programmer deployment to be used as ICs in DSS. Extensive comparisons were made with Decelerator System Simulation Application (DSSA) to validate the mated portion of the ADAMS extraction trajectory. Results of the comparisons improved the fidelity of ADAMS with a ramp pitch profile update from DSSA. Post-test reconstructions resulted in improvements to extraction parachute drag area knock-down factors, extraction line modeling, and the inclusion of ball-to-socket attachments used as a release mechanism on the PTV. Modeling of two Extraction parachutes was based on United States Air Force (USAF) tow test data and integrated into ADAMS for nominal and Monte Carlo trajectory assessments. Video overlay of ADAMS animations and actual C-12 chase plane test videos supported analysis and observation efforts of extraction and separation events. The COTS ADAMS simulation has been integrated with NASA based simulations to provide complete end to end trajectories with a focus on the extraction, separation, and programmer deployment sequence. The flexibility of modifying ADAMS inputs has proven useful for sensitivity studies and extraction/separation modeling efforts. 1

Fraire, Usbaldo, Jr.↗

Multi-disciplinary coupling for integrated design of propulsion systems

Effective computational simulation procedures are described for modeling the inherent multi-disciplinary interactions for determining the true response of propulsion systems. Results are presented for propulsion system responses including multi-discipline coupling effects via (1) coupled multi-discipline tailoring, (2) an integrated system of multidisciplinary simulators, (3) coupled material-behavior/fabrication-process tailoring, (4) sensitivities using a probabilistic simulator, and (5) coupled materials/structures/fracture/probabilistic behavior simulator. The results show that the best designs can be determined if the analysis/tailoring methods account for the multi-disciplinary coupling effects. The coupling across disciplines can be used to develop an integrated interactive multi-discipline numerical propulsion system simulator.

Chamis, C. C.↗

Thermal control for the ground simulation of a space IR sensor system

Active and passive thermal controls for simulations of a space IR sensor system operating in cryogenic temperatures were designed, built, and tested from a component level to a system level. The test results from component tests and integrated system tests have compared very well with theoretical predictions, and thus verify component and integrated thermal math models. These verified models can be modified for use to predict flight systems thermal performance. Thermal vacuum simulations and demonstrations of a space IR system consisted of a target and background scene generator, telescope mirrors supported by a graphite-epoxy metering structure, and an IR sensor. These components are required to operate at cryogenic temperature levels. Each component has its unique thermal control needs. Descriptions are presented of thermal control systems for the test article from component design level to integrated system level along with discussions of component and integrated demonstration tests, and correlation of test data with thermal finite difference models.

Lee, E.↗

A piloted simulation of the backup control system engagement for the YAH-64

A piloted simulator experiment, designed to evaluate and optimize certain backup control system (BUCS) engagement parameters and to provide pilot familiarization with aircraft response prior to flight test of the BUCS in the YAH-64 Advanced Attack Helicopter, is described. Key elements of the simulation were the representation of a control system jam, the pilot's breaking of a shear pin in the jammed control, and the resultant BUCS engagement. To minimize the excursions in aircraft motion which could result from the pilot's control inputs after shear pin breakage, the BUCS control function is blended in gradually. The experiment's results indicate that optimum time to full control authority after shear pin breakage is three seconds in all axes for certain critical tasks. Special pilot training in the recovery from a control system jam may be necessary to minimize unacceptably large aircraft transients in the off-axis.

Blanken, C. L.↗