Search NASA⌕ Search

SEARCH · Search NASA

Results for “Trajectory Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Performance evaluation of an entry research vehicle

The aerodynamic database upon which the missions and the proposed designs of an atmospheric entry research vehicle (ERV) would be based are discussed, along with a trajectory analysis of two missions proposed for the ERV. The ERV is intended as a means to explore reentry techniques, thermal protection systems and cross-range and orbital change maneuvers beyond the operational envelope of the Orbiter. The 25 ft long ERV would have a 13 ft wingspan, allowing it to be launched from the Orbiter bay. The ERV would have atmospheric maneuvering control surfaces and reaction control systems for orbital maneuvers. The total weight would be 12,000 lb. The aerodynamic design for the ERV was developed from wind tunnel, theoretical and Shuttle data for continuum, transition and free-molecule flight regimes. Typical flight profiles for intended missions are outlined.

Powell, R. W.↗

Development and validation of a new guidance device for lateral approach stereotactic breast biopsy

Stereotactic breast biopsy (SBB) is the gold standard for minimally invasive breast cancer diagnosis. Current systems rely on one of two methods for needle insertion: A vertical approach (perpendicular to the breast compression plate) or a lateral approach (parallel to the compression plate). While the vertical approach is more frequently used, it is not feasible in patients with thin breasts (<3 cm thick after compression) or with superficial lesions. Further, existing SBB guidance hardware provides at most one degree of rotational freedom in the needle trajectory, and as such requires a separate skin incision for each biopsy target. The authors present a new design of lateral guidance device for SBB, which addresses the limitations of the vertical approach and provides improvements over the existing lateral guidance hardware. Specifically, the new device provides (1) an adjustable rigid needle support to minimize needle deflection within the breast and (2) an additional degree of rotational freedom in the needle trajectory, allowing the radiologist to sample multiple targets through a single skin incision. This device was compared to a commercial lateral guidance device in a series of phantom experiments. Needle placement error using each device was measured in agar phantoms for needle insertions at lateral depths of 2 and 5 cm. The biopsy success rate for each device was then estimated by performing biopsy procedures in commercial SBB phantoms. SBB performed with the new lateral guidance device provided reduced needle placement error relative to the commercial lateral guidance device (0.89{+-}0.22 vs 1.75{+-}0.35 mm for targets at 2 cm depth; 1.94{+-}0.20 vs 3.21{+-}0.31 mm for targets at 5 cm depth). The new lateral guidance device also provided improved biopsy accuracy in SBB procedures compared to the commercial lateral guidance device (100% vs 58% success rate). Finally, experiments were performed to demonstrate that the new device can accurately sample lesions within thin breast phantoms and multiple lesions through a single incision point. This device can be incorporated directly into the clinical SBB procedural workflow, with no additional electrical hardware, software, postprocessing, or image analysis.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

COMPENSATION OF DETECTOR SOLENOID IN SUPER-B

The SUPER-B detector solenoid has a strong 1.5 T field in the Interaction Region (IR) area, and its tails extend over the range of several meters. The main effect of the solenoid field is coupling of the horizontal and vertical betatron motion which must be corrected in order to preserve the small design beam size at the Interaction Point. The additional effects are orbit and dispersion caused by the angle between the solenoid and beam trajectories. The proposed correction system provides local compensation of the solenoid effects independently for each side of the IR. It includes 'bucking' solenoids to remove the solenoid field tails and a set of skew quadrupoles, dipole correctors and anti-solenoids to cancel linear perturbations to the optics. Details of the correction system are presented.

43 PARTICLE ACCELERATORS↗

Current Activities in the Advanced Exploration Systems ISRU Project

Media Filter MOXIE support: completed flow performance tests and initial dust loading tests of the MOXIE HEPA filter in the Mars Flow Loop Designed and fabricated prototype full-scale scroll filter for testing of renewable filter performance Mars Flow Loop upgrades: installed more sensitive instrumentation, improved imaging, and increased run duration capability Electrostatic Precipitator (ESP) Plasma-physics based model predicts particle charge and trajectory Characterizing dust environment from fluidized-bed injection dust environment using laser sheet visualization and Fine Particle Analyzer Sabatier Design Study Defined the Sabatier design space, including reactor type, thermal management, gas recycling/separation Modeled Sabatier systems with one or two reactors with different types of thermal management Adding thermal management schemes and recycling and gas separation to model Catalyst Screening Performing compression testing on new and used catalyst pellets Performing vibration testing on different catalyst pellet types under different load conditions Preparing to test catalysts for performance and degradation

In-Situ Resource Utilization↗

Intelligent UAS Sense-and-Avoid Utilizing Global Constraints

Sense-and-avoid (SAA) is a critical research topic for enabling the operation of Unmanned Aircraft Systems (UAS) in civilian airspace. SAA involves two planning related problems: 1) plan-recognition to predict the future trajectory of nearby aircraft, and 2) path planning to avoid conflicts with nearby aircraft that pose a threat. We have designed and built components of a novel intelligent sense-and-avoid (iSAA) reasoning framework that takes into account information about aircraft type, transponder code, communications, local routes, airports, airspace, terrain, and weather to more accurately predict near- and medium-term trajectories of nearby aircraft. By using this additional information both the on-board control software and the ground-based UAS operator can make more informed, intelligent decisions to effectively predict and avoid conflicts and maintain separation. While this capability benefits all categories of UASs operating under both Instrument Flight Rules (IFR) and Visual Flight Rules (VFR), it is absolutely essential for allowing smaller UASs to operate VFR at low altitude in uncontrolled airspace for operations such as survey work, wildlife tracking, aerial photography, utilities inspection, crop dusting, and package delivery.

unmanned aircraft systems↗

Orbit Control Operations for the Cassini-Huygens Mission

The Cassini-Huygens spacecraft was launched in 1997 as an international and collaborative mission to study Saturn and its many moons. After a seven-year cruise, Cassini began orbiting Saturn for a four- year tour. This tour consists of 157 planned maneuvers, and their back-up locations, designed to target 52 encounters, mostly of Saturn's largest moon Titan. One of the mission's first activities was to release the Huygens probe to Titan in December 2004. Currently in its last year of the prime mission, Cassini-Huygens continues to obtain valuable data on Saturn, Titan, and Saturn's other satellites. Return of this information is in large part due to a healthy spacecraft and successful navigation. A two-year extended mission, beginning July 2008, will offer the opportunity to continue science activities. With a demanding navigation schedule that compares with the prime tour, the Cassini Navigation team relies on operations procedures developed during the prime mission to carry-out the extended mission objectives. Current processes for orbit control operations evolved from the primary navigational requirement of staying close to predetermined targeting conditions according to Cassini science sequence planning. The reference trajectory is comprised of flyby conditions to be accomplished at minimal propellant cost. Control of the planned reference trajectory orbit, and any trajectory updates, is achieved with the execution of Orbit Trim Maneuvers (OTMs). The procedures for designing, processing, and analyzing OTMs during Cassini operations is presented. First, a brief overview of the Cassini-Huygens Mission is given, followed by a general description of navigation. Orbit control and maneuver execution methods are defined, along with an outline of the orbit control staffing and operations philosophy. Finally, an example schedule of orbit control operations is shown.

navigation↗

Imaging Shielded Configurations Using Near-Horizontal and Near-Vertical Trajectory Cosmic-Ray Muons

This work will describe the proof-of-concept research applying muon tomography technologies based on drift tube systems to create images using near–horizontal trajectory muons. To date, the majority of imaging studies using cosmic-ray muons have used near–vertical trajectory muons. This work compares imaging results using near–vertical trajectory muons with results using near–horizontal trajectory muons. The muon flux is much lower for the near–horizontal trajectory muons, so requiring longer imaging times, but the average muon energy is higher, so the horizontal results are expected to better differentiate high-Z materials. The muon tracking system is easily configurable and can be oriented to capture near–vertical trajectory or near– horizontal trajectory cosmic-ray muons. The software can track each muon passing through the system, and generate 3-D images of the scene. The experimental design and preliminary results will be presented, including the comparisons of detection efficiency, image resolution, and integration times.

muon, passive, imaging, tomography, cosmic↗

Aerocapture - A system design for planetary exploration

The paper presents the results of a study that developed conceptual designs of an atmospheric entry system with moderate to high L/D ratios to establish the concepts of aerocapture into low circular Mars orbits from hyperbolic flyby trajectories. The payloads considered in this study were those currently conceived for the Mars Sample Return (MSR) mission including single mission (SM) and multi-mission (MM) modes. The design concepts developed are also applicable (with small modification) for establishment of closed orbits about Venus and Saturn. The MSR mission payload requires an orbiter, lander, ascent vehicle, and rover, with a total mass of approximately 4000 kg. The emphasis during the study was placed on development of concepts for aerodynamic configuration, the aeroshell design, and a guidance, navigation, and control subsystem.

Cruz, M. I.↗

An Operational Concept for Flying FMS Trajectories in Center and TRACON Airspace

Current Flight Management Systems (FMS) do a good job of constructing and flying an optimal trajectory for a single aircraft. Unfortunately, flight crews are often unable to fly these FMS routes during arrivals at busy airports. The Center TRACON Automation System (CTAS) has been designed to aid Center and TRACON (Terminal Radar Approach Control) controllers in assigning runways, sequencing and vectoring all classes of aircraft. CTAS bases its advisories on trajectory predictions for arriving aircraft using algorithms very similar to those in airborne FMS systems. This paper presents near and far term operational concepts for how a ground ATM (air traffic management) automation system like CTAS could work more effectively with the airborne automation in FMS equipped aircraft. The concepts for a more compatible air-ground system include: 1) a common route databases for both CTAS and FMS; 2) datalink to downlink information on aircraft weight, final approach speed and trajectory intent and to uplink wind information; 3) new FMS functions to allow flight crews to easily update their FMS trajectory to match the trajectory suggested by the ground automation with voice clearances, and 4) in the far term, datalink to downlink user preferred trajectories and to uplink trajectory clearances in the terminal area. The paper analyses some of the human factors issues that may result in allowing aircraft to fly FMS routes during enroute descent and in the terminal area. A series of linked human in the loop flight deck and air traffic control simulations and a field test with the NASA 757 are being conducted at NASA's Ames and Langley Research Centers to address these issues and to evaluate the operational feasibility of these approaches to more efficient flight and increased airport throughput.

Palmer, Everett↗

Missed Thrust Analysis and Design for Low Thrust Cislunar Transfers

This paper details the analysis of the missed thrust problem for low thrust cislunar transfers. Missed thrust analysis is completed for a reference NRHO to DRO transfer that is designed to maximize the final mass without consideration of robustness to unexpected loss of thrust. A new missed thrust design method is presented to include the robustness of the transfer as part of the optimization problem by including a minimal number of branching trajectories tied to the start of thrust arcs in the reference transfer and optimizing them all simultaneously. Results from variations of this approach are presented for and compared to the reference transfer designed without consideration for missed thrust. The results show that this new method can reduce the additional propellant required for recovery from an unexpected 7-day outage by up to 90% without significant increase to the propellant required to complete the reference transfer.

Grebow, Daniel J.↗

Pulse Detonation Engine Air Induction System Analysis

A preliminary mixed-compression inlet design concept for potential pulse-detonation engine (PDE) powered supersonic aircraft was defined and analyzed. The objectives of this research were to conceptually design and integrate an inlet/PDE propulsion system into a supersonic aircraft, perform time-dependent CFD analysis of the inlet flowfield, and to estimate the installed PDE cycle performance. The study was baselined to a NASA Mach 5 Waverider study vehicle in which the baseline over/under turboramjet engines were replaced with a single flowpath PDE propulsion system. As much commonality as possible was maintained with the baseline configuration, including the engine location and forebody lines. Modifications were made to the inlet system's external ramp angles and a rotating cowl lip was incorporated to improve off-design inlet operability and performance. Engines were sized to match the baseline vehicle study's ascent trajectory thrust requirement at Mach 1.2. The majority of this study was focused on a flight Mach number of 3.0. The time-dependent Navier Stokes CFD analyses of a two-dimensional approximation of the inlet was conducted for the Mach 3.0 condition. The Lockheed Martin Tactical Aircraft Systems-developed FALCON CFD code with a two equation 'k-1' turbulence model was used. The downstream PDE was simulated by an array of four sonic nozzles in which the flow areas were rapidly varied in various opening/closing combinations. Results of the CFD study indicated that the inlet design concept operated successfully at the Mach 3.0 condition, satisfying mass capture, total pressure recovery, and operability requirements. Time-dependent analysis indicated that pressure and expansion waves from the simulated valve perturbations did not effect the inlet's operability or performance.

Pegg, R. J.↗

Design of Quasi-Terminator Orbits near Primitive Bodies

Quasi-terminator orbits are a class of quasi-periodic orbits around a primitive body that exist in the vicinity of the well-known terminator orbits. The inherent stability of quasi-terminator trajectories and their wide variety of viewing geometries make them a very compelling option for primitive body mapping missions. In this paper, we discuss orbit design methodologies for selection of an appropriate quasi-terminator orbit that would meet the needs of a specific mission. Convergence of these orbits in an eccentric, higher-fidelity model is also discussed with an example case at Bennu, the target of the upcoming NASA's OSIRIS-REx mission.

mapping↗

CONTROL OF NONLINEAR DYNAMICS BY ACTIVE AND PASSIVE METHODS FOR THE NSLS-II INSERTION DEVICES

Nonlinear effects from insertion devices are potentially a limiting factor for the electron beam quality of modern ring-based light sources, i.e., the on and off-dynamical aperture, leading to reduced injection efficiency and beam lifetime. These effects can be modelled by e.g. kick maps ({approx}1/{gamma}{sup 2}) and controlled by e.g. first-order thin or thick magnetic kicks introduced by 'magic fingers,' 'L-shims,' or 'current strips'. However, due to physical or technological constraints, these corrections are typically only partial. Therefore, a precise model is needed to correctly minimize the residual nonlinear effects for the entire system. We outline a systematic method for integrated design and rapid prototyping based on evaluation of the 3D magnetic field and control of the local trajectory with RADIA, and particle tracking with Tracy-3 for validation. The optimal geometry for the compensating magnetic fields is determined from the results of these simulations using a combination of linear algebra and genetic optimization.

43 PARTICLE ACCELERATORS↗

Comparison of the Effects of Velocity and Range Triggers on Trajectory Dispersions for the Mars 2020 Mission

Mars 2020, the next planned U.S. rover mission to land on Mars, is based on the design of the successful 2012 Mars Science Laboratory (MSL) mission. Mars 2020 retains most of the entry, descent, and landing (EDL) sequences of MSL, including the closed-loop entry guidance scheme based on the Apollo guidance algorithm. However, unlike MSL, Mars 2020 will trigger the parachute deployment and descent sequence on range trigger rather than the previously used velocity trigger. This difference will greatly reduce the landing ellipse sizes. Additionally, the relative contribution of each models to the total ellipse sizes have changed greatly due to the switch to range trigger. This paper considers the effect on trajectory dispersions due to changing the trigger schemes and the contributions of these various models to trajectory and EDL performance.

Dutta, Soumyo↗

VAPRE: A tool to support the design optimization of planetary entry probe missions

The importance of the atmospheric data collected by planetary entry probes has been emphasized since the results of Galileo in 1995 and are reflected in the interest . The results add to our fundamental understanding about the formation and the evolution of our solar system. Of special interest are the Outer Planets Saturn, Uranus and Neptune, serving as missing puzzle pieces to the existing data sets. In order to maximize the data and science return from those missions, the tool VAPRE is developed to facilitate the design optimization of planetary entry probe missions by increasing the trade-space. Using a data set of interplanetary trajectories, it assesses the change in availability and accessibility of entry sites on the planets with respect to their latitudes depending on the hyperbolic arrival velocity. In this paper, we introduce the motivation behind the implementation of VAPRE, the science and engineering input gathered to bridge the knowledge between both fields, the design structure of the implementation as well as the significance and future development and potential of the tool VAPRE for future mission concept developments for planetary probe and lander missions.

Simon, Amy↗

Propulsive maneuver design for the Mars Exploration Rover mission

Starting from approximately 150 candidate Martian landing sites, two distinct sites have been selected for further investigation by sophisticated rovers. The two rovers, named 'Spirit' and 'Opportunity', begin the surface mission respectively to Gusec Crater and Meridiani Planum in January 2004. the rovers are essentially robotic geologists, sent on a mission to research for evidence in the rocks and soil pertaining to the historical presence of water and the ability to possibly sustain life. Before this scientific search can commence, precise trajectory targeting and control is necessary to achieve the entry requirements for the selected landing sites within the constraints of the flight system. The maneuver design challenge is to meet or exceed these requirements while maintaining the necessary design flexibility to accommodate additional project concerns. Opportunities to improve performance and reduce risk based on trajectory control characteristics are also evaluated.

Opportunity↗

BXS Re-calibration

Early in the commissioning it was noticed by Cecile Limborg that the calibration of the BXS spectrometer magnet seemed to be different from the strength of the BX01/BX02 magnets. First the BX01/BX02 currents were adjusted to 135 MeV and the beam energy was adjusted to make the horizontal orbit flat. Then BX01/BX02 magnets were switched off and BXS was adjusted to make the horizontal orbit in the spectrometer line flat, without changing the energy of the beam. The result was that about 140-141 MeV were required on the BXS magnet. This measurement was repeated several times by others with the same results. It was not clear what was causing the error: magnet strength or layout. A position error of about 19 mm of the BXS magnet could explain the difference. Because there was a significant misalignment of the vacuum chamber in the BXS line, the alignment of the whole spectrometer line was checked. The vacuum chamber was corrected, but the magnets were found to be in the proper alignment. So we were left with one (or conceivably two) magnet calibration errors. Because BXS is a wedged shaped magnet, the bend angle depends on the horizontal position of the incoming beam. As mentioned, an offset of the beam position of 19 mm would increase or decrease the bend angle roughly by the ratio of 135/141. The figure of 19 mm is special and caused a considerable confusion during the design and measurement of the BXS magnet. This is best illustrated in Figure 1 which was taken out of the BXS Traveler document. The distance between the horizontal midplanes of the poles and the apex of the beam path was chosen to be 19 mm so the beam is close to the good field region throughout its entire path. Thus it seemed possible that there was an error that resulted in the beam not being on this trajectory, or conversely, that the magnetic measurements were done on the wrong trajectory and the magnet was then mis-calibrated. Mechanical measurements of the vacuum chamber made in the tunnel indicated that the vacuum chamber was in fact in the proper position with respect to the magnet - not 19 mm off to one side - so the former possibility was discounted. Review of the Fiducial Report and an interview with Keith Caban convinced me that there was no error in the coordinate system used for magnet measurements. I went and interviewed Andrew Fischer who did the magnetic measurements of BXS. He had extensive records, including photographs of the setups and could quickly answer quite detailed questions about how the measurement was done. Before the interview, I had a suspicion there might have been a sign flip in the x coordinate which because of the wedge would result in the wrong path length and a miscalibration. Andrew was able to pin-point how this could have happened and later confirmed it by looking an measurement data from the BXG magnet done just after BXS and comparing photographs. It turned out that the sign of the horizontal stage travel that drives the measurement wire was opposite that of the x coordinate in the Traveler, and the sign difference wasn't applied to the data. The origin x = 0 was set up correctly, but the wire moved in the opposite direction to what was expected, just as if the arc had been flipped over about the origin. To quantitatively confirm that this was the cause of the observed difference in calibration I used the 'grid data', which was taken with a Hall probe on the BXS magnet originally to measure the FINT (focusing effect) term, and combined it with the Hall probe data taken on the flipped trajectory, and performed the field integral on a path that should give the same result as the design path. This is best illustrated in Figure 2. The integration path is coincident with the desired path from the pivot points (x = 0) outward. Between the pivot points the integration path is a mirror image of the design path, but because the magnet is fairly uniform, for this portion it gives the same result. Most of the calibration error resulted simply from the different path length between the design path and the measured path. The results of the integration on the equivalent path are given in Table 1. The corrected calibration has been used to generate a new polynomial for BXS which was implemented in the control system.

43 PARTICLE ACCELERATORS↗

Aeroassist flight experiment aerodynamics and aerothermodynamics

The problem is to determine the transitional flow aerodynamics and aerothermodynamics, including the base flow characteristics, of the Aeroassist Flight Experiment (AFE). The justification for the computational fluid dynamic (CFD) Application stems from MSFC's system integration responsibility for the AFE. To insure that the AFE objectives are met, MSFC must understand the limitations and uncertainties of the design data. Perhaps the only method capable of handling the complex physics of the rarefied high energy AFE trajectory is Bird's Direct Simulation Monte Carlo (DSMC) technique. The 3-D code used in this analysis is applicable only to the AFE geometry. It uses the Variable Hard Sphere (VHS) collision model and five specie chemistry model available from Langley Research Center. The code is benchmarked against the AFE flight data and used as an Aeroassisted Space Transfer Vehicle (ASTV) design tool. The code is being used to understand the AFE flow field and verify or modify existing design data. Continued application to lower altitudes is testing the capability of the Numerical Aerodynamic Simulation Facility (NASF) to handle 3-D DSMC and its practicality as an ASTV/AFE design tool.

Brewer, Edwin B.↗