Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Development of a Cure Model for Unsaturated Polyester Resin Systems Based on Processing Conditions

Unsaturated polyester resin (UPR) systems are extensively used in composite materials for applications in the transportation, marine, and infrastructure sectors. There are continually evolving formulations of UPRs that need to be evaluated and optimized for processing. Differential Scanning Calorimetry (DSC) provides valuable insight into the non-isothermal and isothermal behavior of UPRs within a prescribed temperature range. In the present work, non-isothermal DSC tests were carried out between temperatures of 0.0 °C and 250 °C, through different heating and cooling ramp rates. The isothermal DSC tests were carried out between 0.0 and 170 °C. The instantaneous rate of cure of the tested temperatures were measured. The application of an autocatalytic model in a calculator was used to simulate curing behaviors under different processing conditions. As the temperature increased from 10 °C up to 170 °C, the rate of cure reduced, and the heat of reaction increased. The simulated cure behavior from the DSC data showed that the degree of cure (α) maximum value of 71.25% was achieved at the highest heating temperature of 85 °C. For the low heating temperature, i.e., 5 °C, the maximum degree of cure (α) did not exceed 12% because there was not enough heat to activate the catalyst to crosslink further.

Polymer Science↗

Co-Design of Charge Transport Superhighways to Connect Catalytic Sites in Soft Photoelectrochemical Systems

Efficient photon-to-electron-to-molecule conversion requires multi-length scale control over charge transport pathways, where electronic charges are delivered to catalytic sites under high mass transport flux. A fundamental question is how can we co-design charge transport pathways to promote efficient charge transfer to/from catalytic sites in complex three-dimensional architectures? Soft conducting polymer systems offer exceptional promise to provide three-dimensional charge transport networks, where electrolyte (ion and solvent) can interdiffuse to promote long-lived charge carriers and the molecular nature allows for strategic synthetic design of catalytic sites. Herein we combine theoretical and experimental approaches to investigate the earliest stages of photoelectrochemical deposition of near-surface catalytic sites (Pt) on soft bulk heterojunction polymeric semiconductors composed of a prototype donor (PTB7-Th) and a prototype acceptor (N2200) as a model system towards better understanding molecular catalyst-polymer site interactions. We focus initially on photoelectrochemical deposition of low Pt loadings, nanoparticle sizes (formed by progressive nucleation) below 20 nm, for both density functional theory (DFT) modeling studies and for spectroscopic characterization using surface-sensitive X-ray and UV-photoemission (XPS/UPS). DFT modeling of “n-type” N2200 slabs reveal for the first time that sulfur atoms in the thiophene units serve as the lowest-energy adsorption sites for single Pt atoms, while larger Pt clusters engage more complexly with both thiophene and naphthalene diimide (NDI) core sites. Changes in chemical composition observed by X-ray photoelectron spectroscopy (XPS) support the DFT predictions, and the angle-resolved measurements reveal that Pt nucleation initiates at subsurface sites which appear to be localized active domains that promote charge transport/transfer and enable vertical growth toward the surface. These results suggest that light-activated Pt nanoparticle deposition decorates energetically distinct sites, where photoactivity is dictated by the local energetics of those sites, and the fact that they represent the termini of charge transport “super-highways” – a small percentage of the total volume of the donor/acceptor polymeric active layer which carries most of the photocurrent generated during both Pt deposition and photoelectrochemical HER. We posit that these initial studies provide a foundational strategy for design of catalytic sites in the near surface regions of complex polymeric materials and advancing soft semiconductor-based photoelectrochemical systems. Achieving a nanometer-scale understanding of catalyst deposition and the impact of local composition and energetics on that placement, should ultimately provide the design guidelines (co-design) for a broad array of catalysts at sites that optimize that efficiency and maximize platform durability.

14 SOLAR ENERGY↗

Process-Dependent Properties in Colloidally Synthesized “Giant” Core/Shell Nanocrystal Quantum Dots

Due to their characteristic bright and stable photoluminescence, semiconductor nanocrystal quantum dots (NQDs) have attracted much interest as efficient light emitters for applications from single-particle tracking to solid-state lighting. Despite their numerous enabling traits, however, NQD optical properties are frustratingly sensitive to their chemical environment, exhibit fluorescence intermittency ('blinking'), and are susceptible to Auger recombination, an efficient nonradiative decay process. Previously, we showed for the first time that colloidal CdSe/CdS core/shell nanocrystal quantum dots (NQDs) comprising ultrathick shells (number of shell monolayers, n, > 10) grown by protracted successive ionic layer adsorption and reaction (SILAR) leads to remarkable photostability and significantly suppressed blinking behavior as a function of increasing shell thickness. We have also shown that these so-called 'giant' NQDs (g-NQDs) afford nearly complete suppression of non-radiative Auger recombination, revealed in our studies as long biexciton lifetimes and efficient multiexciton emission. The unique behavior of this core/shell system prompted us to assess correlations between specific physicochemical properties - beyond shell thickness - and functionality. Here, we demonstrate the ability of particle shape/faceting, crystalline phase, and core size to determine ensemble and single-particle optical properties (quantum yield/brightness, blinking, radiative lifetimes). Significantly, we show how reaction process parameters (surface-stabilizing ligands, ligand:NQD ratio, choice of 'inert' solvent, and modifications to the SILAR method itself) can be tuned to modify these function-dictating NQD physical properties, ultimately leading to an optimized synthetic approach that results in the complete suppression of blinking. We find that the resulting 'guiding principles' can be applied to other NQD compositions, allowing us to achieve non-blinking behavior in the near-infrared. Lastly, in addition to realizing novel light-emission properties by refining nanoscale architectures at the single-NQD level, we also investigate collective properties by assembling our core/shell NQDs into larger scale arrays.

36 MATERIALS SCIENCE↗

Overview of the multifaceted activities towards development and deployment of nuclear-grade FeCrAl Alloys

A large effort is underway under the leadership of US DOE Fuel Cycle R&D program to develop advanced FeCrAl alloys as accident tolerant fuel (ATF) cladding to replace Zr-based alloys in light water reactors. The primary motivation is the excellent oxidation resistance of these alloys in high-temperature steam environments right up to their melting point (roughly three orders of magnitude slower oxidation kinetics than zirconium). A multifaceted effort is ongoing to rapidly advance FeCrAl alloys as a mature ATF concept. The activities span the broad spectrum of alloy development, environmental testing (high-temperature high-pressure water and elevated temperature steam), detailed mechanical characterization, material property database development, neutron irradiation, thin tube production, and multiple integral fuel test campaigns. Instead of off-the-shelf commercial alloys that might not prove optimal for the LWR fuel cladding application, a large amount of effort has been placed on the alloy development to identify the most optimum composition and microstructure for this application. The development program is targeting a cladding that offers performance comparable to or better than modern Zr-based alloys under normal operating and off-normal conditions. This paper provides a comprehensive overview of the systematic effort to advance nuclear-grade FeCrAl alloys as an ATF cladding in commercial LWRs.

Field, Kevin G↗

Overview of the multifaceted activities towards development and deployment of nuclear-grade FeCrAl alloys

A large effort is underway under the leadership of US DOE Fuel Cycle Research program to develop advanced FeCrAl alloys as accident tolerant fuel (ATF) cladding to replace Zr-based alloys in light water reactors. The primary motivation is the excellent oxidation resistance of these alloys in high-temperature steam environments right up to their melting point (roughly three orders of magnitude slower oxidation kinetics than zirconium). A multifaceted effort is ongoing to rapidly advance FeCrAl alloys as a mature ATF concept. The activities span the broad spectrum of alloy development, environmental testing (high-temperature high-pressure water and elevated temperature steam), detailed mechanical characterization, material property database development, neutron irradiation, thin tube production, and multiple integral fuel test campaigns. Instead of off-the-shelf commercial alloys that might not prove optimal for the LWR fuel cladding application, a large amount of effort has been placed on the alloy development to identify the most optimum composition and microstructure for this application. The development program is targeting a cladding that offers performance comparable to or better than modern Zr-based alloys under normal operating and off-normal conditions. This paper provides a comprehensive overview of the systematic effort to advance nuclear-grade FeCrAl alloys as an ATF cladding in commercial LWRs. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Digitalization mapping and assessment process supporting ION strategic transformation activities

The existing fleet of commercial nuclear power plants (NPPs) are an important asset in the nation’s portfolio of electrical generating resources. Their continued safe and reliable operation are critical to providing a large source of carbon-free electricity to power the nation’s economy. The United States Department of Energy’s (DOE) Light Water Reactor Sustainability (LWRS) Program develops the scientific bases, methods, and tools, for the continued safe and economical operation of the nation's commercial NPPs. The Plant Modernization Pathway within LWRS Program focuses on providing guidance to industry on the full-scale implementation of modernization solutions for NPPs that significantly reduce the technical and financial risks associated with modernization. This research is focused on helping the nuclear industry understand how to digitize and digitalize their NPPs so that they can design their modernization solutions to be scalable, sustainable, and integrated both laterally and horizontally within their organization. That is, this research creates a digital transformation in NPPs by reshaping cultural mindsets and by identifying business efficiencies. In partnership with industry, and using four previously established guiding principles for digitalization, this research supported NPP modernization through assessing readiness for digitalization as a means to achieve integrated operations for nuclear. Specifically, this research created an assessment to review an entire organization’s work processes to gather information about the digitalization health of the plant. The assessment tools were administered to plant employees, and the results were used to develop a digitalization plan. The survey assessment identified the optimal candidate processes that would most benefit from a digitalization initiative which were revealed through analytical frameworks. One analysis calculated mean digitalization health indicator scores for all endorsed activities which allowed the researchers to rank and color code the results for easy identification. Individual health indicator scores are also provided, should our industry partner wish to understand these findings according to their own organizational priorities, business considerations and desired end-state. The results were also analyzed from the perspective that organizations are comprised of different types of innovators (e.g., generators, optimizers, conceptualizers, and implementers), which differentially affects the organization’s ability to comprehend and adapt to change (i.e., opportunities to innovate). Understanding the relative composition of innovator types at an NPP allows them to gather insights into the strengths and weaknesses they have in innovating how work is performed. For the utility that partnered with this research team, the results showed that implementers make up the largest portion of respondents and conceptualizers the smallest portion. Knowing the proportion of innovator types gave this organization insights on how they can effectively implement their innovation solutions. Additionally, the results were analyzed from a technical, economic, and risk perspective to identify and quantify work reduction opportunities (WROs). Recognizing that not all cost-saving opportunities are the same, a Technical, Economic and Risk Assessment (TERA) was performed to evaluate WROs to identify areas of greatest potential and lowest risk. The key results from TERA included a digitalization opportunity score for each activity, and a calculation of potential cost savings. These two outputs formed the bases for calculating a priority index and rank for the activities/processes assessed. From the prioritization calculations, TERA can then help the utility 1) decide what digitalization priorities to invest money in implementing and then 2) calculates how much should be invested in the digitalization initiatives selected to achieve cost savings and/or an acceptable return on investment. Last, onsite interviews revealed several inefficiencies in the standard work processes that occur cross-departmentally that are due to the absence of digitized and digitalized processes. Examples of these include time spent scanning paper documents and then uploading the documents electronically, obtaining signatures, and searching for desired information. This represents a digital but not digitalized process. Over 15 opportunities to improve work processes were identified through this multi-method digitalization assessment. The various analytical assessments used (e.g., TERA, digitalization health indicator scores), as well as discussions with the utility partner, corroborated that all the opportunities identified had a strong potential to make work processes more efficient and to improve overall performance of the NPP.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The importance of chain connectivity in the formation of non-covalent interactions between polymers and single-walled carbon nanotubes and its impact on dispersion

In this study we investigate the formation of non-covalent electron donor acceptor (EDA) interactions between polymers and single-walled carbon nanotubes (SWNTs) with the goal of optimizing interfacial adhesion and homogeneity of nanocomposites without modifying the SWNT native surface. Nanocomposites of SWNTs and three sets of polymer matrices with varying composition of electron donating 2-(dimethylamino)ethyl methacrylate (DMAEMA) or electron accepting acrylonitrile (AN) and cyanostyrene (CNSt) were prepared, quantitatively characterized by optical microscopy and Raman spectroscopy (Raman mapping, Raman D* peak shifts) and qualitatively compared through thick film composite visualization. The experimental data show that copolymers with 30 mol% DMAEMA, 45 mol% AN, 23 mol% CNSt and polyacrylonitrile homopolymer have the highest extent of intermolecular interaction, which translates to an optimum SWNT spatial dispersion among the series. These results are found to correlate very well with the intermolecular interaction energies obtained from quantum density functional theory calculations. Both experimental and computational results also illustrate that chain connectivity is critical in controlling the accessibility of the functional groups to form intermolecular interactions. This means that an adequate distance between interacting functional groups on a polymer chain is needed in order to allow efficient intermolecular contact. Thus, controlling the amount of electron donating or withdrawing moieties throughout the polymer chain will direct the extent of EDA interaction, which enables tuning the SWNT dispersion.

36 MATERIALS SCIENCE↗

Application of the Differential Evolution Method to Solving Inverse Transport Problems

The differential evolution method, a powerful stochastic optimization algorithm that mimics the process of evolution in nature, is applied to inverse transport problems with several unknown parameters of mixed types, including interface location identification, source composition identification, and material mass density identification, in spherical and cylindrical radioactive source/shield systems. In spherical systems, measurements of leakages of discrete gamma-ray lines are assumed, while in cylindrical systems, measurements of scalar fluxes of discrete lines at points outside the system are assumed. The performance of the differential evolution algorithm is compared to the Levenberg-Marquardt method, a standard gradient-based technique, and the covariance matrix adaptation evolution strategy, another stochastic technique, on a variety of numerical test problems with several (i.e., three or more) unknown parameters. Numerical results indicate that differential evolution is the most adept method for finding the global optimum for these problems. In spherical geometry, differential evolution implemented serially is run-time competitive with gradient-based methods, while a parallel version of differential evolution would be run-time competitive with gradient-based techniques in cylindrical geometry. A hybrid differential evolution/Levenberg-Marquardt method is also introduced, and numerical results indicate that it can be a fast and robust optimizer for inverse transport problems.

99 GENERAL AND MISCELLANEOUS↗

MA Doping Analysis on Breeding Capability and Protected Plutonium Production of Large FBR

Spent fuel from LWR can be seen as long-live waste if it is not recycled or as a 'new fuel' resource if it is recycled into the reactors. Uranium and plutonium have been used for 'new fuel' resources from LWR spent fuel as MOX fuel type which is loaded into thermal reactor or fast reactor types. Other actinides from the spent fuel such as neptunium, americium and curium as minor actinide (MA) are considered to be loaded into the reactors for specific purposes, recently. Those purposes such as for increasing protected plutonium production and breeding capability for protected plutonium as well as in the same time those amount of MA can be reduced to a small quantity as a burner or transmutation purpose. Some investigations and scientific approaches are performed in order to increase a material ''barrier'' in plutonium isotope composition by increasing the even mass number of plutonium isotope such as Pu-238, Pu-240 and Pu-242 as plutonium protected composition. Higher material barrier which related to intrinsic properties of plutonium isotopes with even mass number (Pu-238, Pu-240 and Pu-242), are recognized because of their intense decay heat (DH) and high spontaneous fission neutron (SFN) rates. Those even number mass of plutonium isotope contribute to some criteria of plutonium characterization which will be adopted for present study such as IAEA, Pellaud and Kessler criteria (IAEA, 1972; Pellaud, 2002; and Kessler, 2007). The present paper intends to evaluate the breeding capability as a fuel sustainability index of the reactors and to analyze the composition of protected plutonium production of large power reactor based on the FaCT FBR as reference (Ohki, et al., 2008). Three dimensional FBR core configuration has been adopted which is based on the core optimization calculation of SRAC-CITATION code as reactor core analysis and JENDL-3.3 is adopted for nuclear data library. Some MA doping materials are loaded into the blanket regions which can be considered as breeding region for protected plutonium production. Breeding capability of the reactor can be increased effectively by increasing MA doping rate while criticality condition of the reactor is reduced by doping MA. Adopting MA cycle is also effective to increase the isotopic Pu-238 production in plutonium vector composition for denaturing purpose of plutonium.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

A superstructure optimization approach for process synthesis under complex reaction networks

Here in this work, we present mixed integer linear programming methods for the synthesis of processes that involve complex reaction networks. Specifically, we consider the modeling of reactors and interconnecting streams in systems where the composition of the reactor inlet streams can vary substantially, thereby making the determination of the limiting component as well as the calculation of the stream heating/cooling and power requirements challenging. First, towards the modeling of reactors, we develop an extent-based method which detects the limiting reactant of each reaction occurring in parallel with others, based on the inlet flows of the reactants. Second, we develop a computationally tractable method for the calculation of the work and heating/cooling duty needed to condition any stream of a process based on simple calculations that can be performed offline. Finally, we present how the two aforementioned components can be integrated in an optimization model generated based on a process superstructure. We demonstrate the application of the developed methods for the synthesis of a biorefinery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Application of Advanced Materials Processing to Enable Direct Production of Fast Reactor Fuel Alloys

Argonne National Laboratory (the Contractor), located in Lemont, IL, and Oklo, Inc. (the Participant), headquartered in Sunnyvale, CA, entered into a Cooperative Research and Development Agreement (CRADA) to integrate advanced electrorefining co-deposition and molten-salt monitoring technologies to produce a uranium-transuranic (U/TRU) alloy within a controlled composition range that can be used as fast reactor fuel for Oklo, Inc.’s advanced reactor technology. Argonne performed the integration of electrorefining and process monitoring technologies, determined operating parameters for producing U/TRU alloys, and developed optimized design and operating parameters for co-deposition of U/TRU alloys. Oklo, Inc. worked with Argonne and the Nuclear Regulatory Commission (NRC) to provide the necessary process documentation to begin implementing pyroprocessing technology in the fast reactor fuel production process. Outcomes of this project included a pilot-scale co-deposition cathode design and technical basis for the operation of the co-deposition electrorefiner to produce U/TRU alloys with controlled composition.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Bridging the Gap Between Pure and Mixed-Gas Performance of Thin-Film Composite Membranes

This study examines the influence of cell design on mixed-gas testing with PolyActive™ TFC membranes, featuring pure-gas CO₂ permeance of 1700–3100 GPU, representative of state-of-the-art CO₂/N₂ separation membranes. By designing and 3D-printing a counter-current permeation cell with optimized flow efficiency, we achieved a 33–41% increase in mixed-gas CO₂ permeance compared to traditional cells. Additionally, a comparison of sweep-gas and vacuum permeation methods revealed that vacuum operation mitigates downstream polarization, enhancing mixed-gas CO₂ permeance by 41%. These results underscore the critical role of permeation cell design and testing methods in accurately evaluating membrane performance, with significant implications for scaling up TFC membranes and optimizing industrial processes.

3D printing↗

Parametric Optimization of Nanostructured Alumina Forming Austenitic Alloys

Alumina-forming austenitic (AFA) alloys provide excellent oxidation resistance through the formation of a stable alumina scale, but their relatively high Ni content might limit application in core structural components because of helium generation and swelling under irradiation. Increasing the density of nanoscale features in the microstructure is a promising route to improve sink strength and mitigate these effects. Conventional oxide dispersion–strengthened (ODS) steels achieve this through mechanical alloying (MA), but the approach is costly and difficult to scale. In this milestone, additive manufacturing was applied as an alternative pathway to fabricate nanostructured AFA (NAFA) alloys with dual precipitation of oxides and nitrides enabled by reactive atmosphere processing. In FY25, two compositions, NAFA-1 (AFA-05) and NAFA-2, were produced and compared. Both alloys achieved densities above 99% of theoretical values, but NAFA-2 exhibited microcracking associated with Nb-rich intermetallic formation, indicating the need for further chemistry optimization. Nitrogen and oxygen uptake was confirmed on selected builds, demonstrating the intended dual-precipitate dispersion. Mechanical testing showed that AM-processed NAFA alloys exceed conventionally produced ODS steels in high-temperature tensile strength and fracture toughness. Preliminary Cu ion irradiation results further suggest improved resistance compared to wrought austenitic alloys. While the current alloys are promising for their compatibility in high-temperature air or liquid Pb environments, modifications to composition will be required for long-term operation in high-temperature impure sodium systems. Future work will focus on refining alloy chemistry to suppress laser powder bed fusion–induced cracking and scaling production to reactor-relevant dimensions using directed energy deposition as a pathway toward net-shape cladding fabrication.

36 MATERIALS SCIENCE↗

Sustainable Energy Solutions Task 5.1:Expand the Number of Faculty Working in Wind Energy: Wind Energy Supply Chain and Logistics

Wind as a source of energy has gained a significant amount of attention because it is free and green. Construction of a wind farm involves considerable investment, which includes the cost of turbines, nacelles, and towers as well as logistical costs such as transportation of oversized parts and installation costs such as crane-rental costs. The terrain effects at the project site exert considerable influence on the turbine assembly rate and the project duration, which increases the overall installation cost. For higher capacity wind turbines (>3MW), the rental cost of the cranes is significant. In this study, the impact of interest rate, sales price of electricity, terrain effects and availability of cranes on the duration of installation and payback period for the project is analyzed. Optimization of the logistic activities involved during the construction phase of a wind farm contributes to the reduction of the project duration and also increases electricity generation during the construction phase.

17 WIND ENERGY↗

Additive Manufacturing of High-Entropy Alloys: A Review

Owing to the reduced defects, low cost, and high efficiency, the additive manufacturing (AM) technique has attracted increasingly attention and has been applied in high-entropy alloys (HEAs) in recent years. It was found that AM-processed HEAs possess an optimized microstructure and improved mechanical properties. However, no report has been proposed to review the application of the AM method in preparing bulk HEAs. Hence, it is necessary to introduce AM-processed HEAs in terms of applications, microstructures, mechanical properties, and challenges to provide readers with fundamental understanding. Specifically, we reviewed (1) the application of AM methods in the fabrication of HEAs and (2) the post-heat treatment effect on the microstructural evolution and mechanical properties. Compared with the casting counterparts, AM-HEAs were found to have a superior yield strength and ductility as a consequence of the fine microstructure formed during the rapid solidification in the fabrication process. The post-treatment, such as high isostatic pressing (HIP), can further enhance their properties by removing the existing fabrication defects and residual stress in the AM-HEAs. Furthermore, the mechanical properties can be tuned by either reducing the pre-heating temperature to hinder the phase partitioning or modifying the composition of the HEA to stabilize the solid-solution phase or ductile intermetallic phase in AM materials. Moreover, the processing parameters, fabrication orientation, and scanning method can be optimized to further improve the mechanical performance of the as-built-HEAs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Modeling and simulation of InGaN/GaN quantum dots solar cell

Currently, quantum dots have attracted attention in the field of optoelectronics, and are used to overcome the limits of a conventional solar cell. Here, an In{sub 0.25}Ga{sub 0.75}N/GaN Quantum Dots Solar Cell has been modeled and simulated using Silvaco Atlas. Our results show that the short circuit current increases with the insertion of the InGaN quantum dots inside the intrinsic region of a GaN pin solar cell. In contrary, the open circuit voltage decreases. A relative optimization of the conversion efficiency of 54.77% was achieved comparing a 5-layers In{sub 0.25}Ga{sub 0.75}N/GaN quantum dots with pin solar cell. The conversion efficiency begins to decline beyond 5-layers quantum dots introduced. Indium composition of 10 % improves relatively the efficiency about 42.58% and a temperature of 285 K gives better conversion efficiency of 13.14%.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A comparative study of ethanol production using dilute acid, ionic liquid and AFEX™ pretreated corn stover

In a biorefinery producing cellulosic biofuels, biomass pretreatment will significantly influence the efficacy of enzymatic hydrolysis and microbial fermentation. Comparison of different biomass pretreatment techniques by studying the impact of pretreatment on downstream operations at industrially relevant conditions and performing comprehensive mass balances will help focus attention on necessary process improvements, and thereby help reduce the cost of biofuel production. An on-going collaboration between the three US Department of Energy (DOE) funded bioenergy research centers (Great Lakes Bioenergy Research Center (GLBRC), Joint BioEnergy Institute (JBEI) and BioEnergy Science Center (BESC)) has given us a unique opportunity to compare the performance of three pretreatment processes, notably dilute acid (DA), ionic liquid (IL) and ammonia fiber expansion (AFEX TM ), using the same source of corn stover. Separate hydrolysis and fermentation (SHF) was carried out using various combinations of commercially available enzymes and engineered yeast (Saccharomyces cerevisiae 424A) strain. The optimal commercial enzyme combination (Ctec2: Htec2: Multifect Pectinase, percentage total protein loading basis) was evaluated for each pretreatment with a microplate-based assay using milled pretreated solids at 0.2% glucan loading and 15 mg total protein loading/g of glucan. The best enzyme combinations were 67:33:0 for DA, 39:33:28 for IL and 67:17:17 for AFEX. The amounts of sugar (kg) (glucose: xylose: total gluco- and xylo-oligomers) per 100 kg of untreated corn stover produced after 72 hours of 6% glucan loading enzymatic hydrolysis were: DA (25:2:2), IL (31:15:2) and AFEX (26:13:7). Additionally, the amounts of ethanol (kg) produced per 100 kg of untreated corn stover and the respective ethanol metabolic yield (%) achieved with exogenous nutrient supplemented fermentations were: DA (14.0, 92.0%), IL (21.2, 93.0%) and AFEX (20.5, 95.0%), respectively. The reason for lower ethanol yield for DA is because most of the xylose produced during the pretreatment was removed and not converted to ethanol during fermentation. Compositional analysis of the pretreated biomass solids showed no significant change in composition for AFEX treated corn stover, while about 85% of hemicellulose was solubilized after DA pretreatment, and about 90% of lignin was removed after IL pretreatment. As expected, the optimal commercial enzyme combination was different for the solids prepared by different pretreatment technologies. Due to loss of nutrients during the pretreatment and washing steps, DA and IL pretreated hydrolysates required exogenous nutrient supplementation to ferment glucose and xylose efficiently, while AFEX pretreated hydrolysate did not require nutrient supplementation.

09 BIOMASS FUELS↗

Atomic-Level Understanding of Surface Reconstruction Based on Li[Ni x Mn y Co 1–x–y ]O 2 Single-Crystal Studies

The stability of cathode particle surfaces that are directly exposed to the electrolyte is one of the most crucial and determining factors for cathode performance at high operating voltages. Theory has predicted a strong dependence of surface stability on chemical compositions as well as surface facets of layered oxides, yet conflicting results on the correlations exist as most experimental studies focus on cycled secondary particles recovered from composite electrodes. Here, we synthesize well-formed Li[Ni x Mn y Co 1–x–y ]O 2 (NMC) single-crystal samples, carefully define pristine surface properties, and then monitor their evolution with cycling. Atomic-resolution scanning transmission electron microscopy (STEM) imaging and electron energy loss spectroscopy (EELS) analysis show the formation of a surface reconstruction layer (SRL) as well as an extended surface reduction layer on pristine, Li-permeable non-(001) surfaces, even before cycling. We reveal a transition region with chemical gradient, in which the layered structure gradually densifies and eventually transforms into the SRL on the top surface. Contrary to these observations, no SRL is observed on pristine, Li-impermeable (001) surfaces, revealing the facet-dependent nature of surface reconstructions during particle synthesis. Upon electrochemical cycling, significant composition-and facet-dependent SRL growth is observed. The driving force and mechanism for surface reconstruction are further discussed. The present study provides insights into the origin as well as the nature of SRLs, highlighting the significance of surface engineering in cathode material optimization.

25 ENERGY STORAGE↗