Search NASA⌕ Search

SEARCH · Search NASA

Results for “loop currents”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Cracking behavior and microstructure of austenitic stainless steels and alloy 690 irradiated in BOR-60 reactor, phase I.

Cracking behavior of stainless steels specimens irradiated in the BOR-60 at about 320 C is studied. The primary objective of this research is to improve the mechanistic understanding of irradiation-assisted stress corrosion cracking (IASCC) of core internal components under conditions relevant to pressurized water reactors. The current report covers several baseline tests in air, a comparison study in high-dissolved-oxygen environment, and TEM characterization of irradiation defect structure. Slow strain rate tensile (SSRT) tests were conducted in air and in high-dissolved-oxygen (DO) water with selected 5- and 10-dpa specimens. The results in high-DO water were compared with those from earlier tests with identical materials irradiated in the Halden reactor to a similar dose. The SSRT tests produced similar results among different materials irradiated in the Halden and BOR-60 reactors. However, the post-irradiation strength for the BOR-60 specimens was consistently lower than that of the corresponding Halden specimens. The elongation of the BOR-60 specimens was also greater than that of their Halden specimens. Intergranular cracking in high-DO water was consistent for most of the tested materials in the Halden and BOR-60 irradiations. Nonetheless, the BOR-60 irradiation was somewhat less effective in stimulating IG fracture among the tested materials. Microstructural characterization was also carried out using transmission electron microscopy on selected BOR-60 specimens irradiated to {approx}25 dpa. No voids were observed in irradiated austenitic stainless steels and cast stainless steels, while a few voids were found in base and grain-boundary-engineered Alloy 690. All the irradiated microstructures were dominated by a high density of Frank loops, which varied in mean size and density for different alloys.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

SPECTROSCOPIC OBSERVATIONS OF Fe XVIII IN SOLAR ACTIVE REGIONS

The large uncertainties associated with measuring the amount of high temperature emission in solar active regions (ARs) represents a significant impediment to making progress on the coronal heating problem. Most current observations at temperatures of 3 MK and above are taken with broadband soft X-ray instruments. Such measurements have proven difficult to interpret unambiguously. Here, we present the first spectroscopic observations of the Fe XVIII 974.86 A emission line in an on-disk AR taken with the SUMER instrument on SOHO. Fe XVIII has a peak formation temperature of 7.1 MK and provides important constraints on the amount of impulsive heating in the corona. Detailed evaluation of the spectra and comparison of the SUMER data with soft X-ray images from the X-Ray Telescope on Hinode confirm that this line is unblended. We also compare the spectroscopic data with observations from the Atmospheric Imaging Assembly (AIA) 94 A channel on the Solar Dynamics Observatory. The AIA 94 A channel also contains Fe XVIII, but is blended with emission formed at lower temperatures. We find that it is possible to remove the contaminating blends and form relatively pure Fe XVIII images that are consistent with the spectroscopic observations from SUMER. The observed spectra also contain the Ca XIV 943.63 A line that, although a factor 2-6 weaker than the Fe XVIII 974.86 A line, allows us to probe the plasma around 3.5 MK. The observed ratio between the two lines indicates (isothermal approximation) that most of the plasma in the brighter Fe XVIII AR loops is at temperatures between 3.5 and 4 MK.

79 ASTRONOMY AND ASTROPHYSICS↗

Termination Methods for REBCO Tape High-Current Cable Conductors

Three types of joint termination methods for a 2G HTS cable have been developed: YBCO-BSCCO, YBCO-YBCO, and Folding-fan soldered terminations. For the YBCO-BSCCO terminator, each YBCO tape of a cable is connected to a BSCCO tape while the other ends of BSCCO tapes are bundled together and soldered inside a copper tube. The same termination was tested more than 30 times in liquid nitrogen and helium without any problems. It was operated at 10 kA in liquid helium and more than 2 kA in liquid nitrogen. The YBCO-BSCCO termination has been confirmed to be very easy to fabricate and convenient for a cable test since it is reusable. A YBCO tape termination method without BSCCO tape also has been proposed. Both terminations will be very useful for 2G HTS cables. These terminations are demountable if they are not soldered at the junction between tapes. Joint resistance is greatly reduced with increasing applied pressure especially for YBCO-YBCO contact joints. However, in the case of a YBCO-BSCCO joint, the BSCCO tapes may degrade at high pressure. The contact pressure should be optimized to obtain low joint resistance. If the contact surfaces of YBCO-BSCCO and YBCO-YBCO terminations are soldered for a permanent joint, the termination resistances are lower, and better uniformity will be achieved. Another termination is the Folding-fan termination. It is a soldered joint. Joint resistance distributions among cable tapes for these termination methods have been evaluated. Mechanical contact joint resistance distributions between YBCO-BSCCO tapes and YBCO-YBCO tapes have been measured under various contact pressures and contact surface conditions at 77 K. By optimization of the applied contact pressure and contact surface treatment techniques the contact joint resistance of a termination joint can be reduced and a better uniformity can be obtained. We also discussed effects on a cable performance due to no-uniformity of termination resistances, a loop resistance between two tapes in a termination of a cable, and a series operation of two 2G YBCO Twisted Stacked-Tape Cable (TSTC) conductors.

Takayasu, M.↗

Models and methods for assessing the value of HVDC and MVDC technologies in modern power grids

This report reflects the results of U.S. Department of Energy’s (DOE) Grid Modernization project 0074 “Models and methods for assessing the value of HVDC [high-voltage direct current] and MTDC [multi-terminal direct current] technologies in modern power grids.” The work was done by the Pacific Northwest National Laboratory (PNNL) and Oak Ridge National Laboratory (ORNL) in cooperation with Mid-Continent Independent System Operator (MISO) and Siemens. The main motivation of this study was to show the benefit of using direct current (DC) systems larger than those in existence today as they overlap with the alternating current (AC) systems. Proper use of their flexibility in terms of active/reactive power control and fast response can provide much-needed services to the grid at the same time as moving large blocks of energy to take advantage of cost diversity. Ultimately, the project’s success will enable decision-makers and investors to make well-informed decisions regarding this use of DC systems. This project showed the technical feasibility of HVDC macrogrid for frequency control and congestion relief in addition to bulk power transfers. Industry-established models for commonly used technologies were employed, along with high-fidelity models for recently developed HVDC converter technologies; like the modular multilevel converters (MMCs), a voltage source converters (VSC). Models for General Electric Positive Sequence Load Flow (GE PSLF) and Siemens Power System Simulator (PSS/E), widely used analysis programs, were for the first time adapted to include at the same time both Western Electricity Coordinating Council (WECC) and Eastern Interconnection (EI), the two largest North American interconnections. The high-fidelity models and their control were developed in detail for MMC system and extended to HVDC systems in point-to-point and in three-node multi-terminal configurations. Using a continental-level mixed AC-DC grid model, and using a HVDC macrogrid power flow and transient stability model, the results showed that the HVDC macrogrid relieved congestion and mitigated loop flows in AC networks, and provided up to 24% improvement in frequency responses. These are realistic studies, based on the 2025 heavy summer and EI multi-regional modeling working group (MMWG) 2026 summer peak cases. This work developed high-fidelity models and simulation algorithms to understand the dynamics of MMC. The developed models and simulation algorithms are up to 25 times faster than the existing algorithms. Models and control algorithms for high-fidelity models were designed and tested for point-to-point and multi-terminal configurations. The multi-terminal configuration was tested connecting simplified models of EI, WI, and Electric Reliability Council of Texas (ERCOT). The developed models showed up to 45% improvement in frequency response with the connection of all the three asynchronous interconnections in the United States using fast and advanced DC technologies like the multi-terminal MMC-DC system. Future work will look into developing high-fidelity models of other advanced DC technologies, combining high-fidelity models with the continental-level model, incorporating additional services. More scenarios involving large-scale HVDC and MTDC will be evaluated.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Quantification of functional impact classification on the current U.S. nuclear fleet

Currently, nuclear power generates only a small fraction of the world's electricity, though it does have the potential to meet the needs of the world as long as its production can compete with the alternative energy base load producers. In U.S the commercial nuclear fleet comprises of Light Water Reactors (LWRs), consisting of Pressurized Water Reactors (PWRs) and Boiling Water Reactors (BWRs). Many plants experience multiple events each year, which lead to reactor trips or scrams. This subsequently leads to plants being off the grid, which is not an economically favorable situation in the current energy markets. This study helps identify functional impact (FI) event categories for both PWR's and BWR's. Understanding that not all events and their causes can be anticipated, current industry best practices implement lessons learned to provide challenges and issues identification. In turn these are studied to achieve improved operational practices, and design modifications. This leads to overall enhanced resiliency. FI groups are the categories of initiating events (IE). IEs are unplanned events that occur while a nuclear plant is in critical operation, and requires that the plant be shut down to achieve a stable state. When a risk cannot be eliminated, IEs are identified and studied to reduce the risk and contribute to the identification of mitigations, safer designs and operational practices. Breaking IE events into groups' results in the classification of FI groups. A FI group is a risk-significant event category that could impact the ability of a NPP to remove decay heat from the reactor. Inability to remove decay heat from the reactor has the potential to lead to core damage. For an event to be considered a FI, it must be associated with a manual or automatic reactor trip, irrespective of the order of events. In addition, the plant must be at or above the point of adding heat and the event must happen before or shortly after a reactor trip. One or more FIs may be identified in any individual reactor trip sequence. The relationship between FI sequence, and/or frequency per a plant event is outside the scope of this paper. For example, the loss of offsite power (LOOP) can occur from eternal events (i.e. weather, human, wildlife etc.). This results in an event that requires a transfer of power to an emergency source, such as a generator, which produces a reactor trip and then a closure of main steam isolation valves (MSIVS). The FI applicable to this reactor trip sequence would be LOOP and closure of at least one MSIV in each main steam line. The results presented herein are focused on the analysis and evaluation of FI event categories. Only FI categories that can be found in IE studies, Initialing Events Spreadsheet and are recorded in a historical review of Licensee Event Reports (LERs) from 1988 through 2013. The results of this analysis can support plant decisions, design, procedures, and identify weakness.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Helium-3 Production via Lithium-6 Activation in an Accelerator-Driven Reactor

In this paper, the possibility of using an accelerator-driven subcritical reactor to produce helium-3 is explored. Current supply of helium-3 in the United States is running low. Helium-3 has many applications in neutron detection, high-energy physics, and national security, and has a growing demand in the scientific community for its properties. The main source of helium-3 in the United States is from dismantling nuclear arms, where tritium is allowed to decay into helium-3. There are no current, significant future plans for increasing helium-3 production. However, the projected demand of this isotope is expected to increase dramatically, with greater research into aneutronic fusion, and allotments of helium for the Spallation Neutron Source, and ITER expected in years to come. Tritium, with a half-life of 12.3 years, will take time to decay to helium-3, which means production needs to start now to counter the future deficit. This helium-3 production system sets out to be an economical, and safe solution for this future deficit. A zirconium-lithium mixture is utilized as a target for breeding helium-3. Specifically, the target rods will consist of lithium aluminate pellets with diameters ranging from 100 to 500 microns, dispersed within a zirconium matrix. Lithium targets in pellet form were chosen over a solid rod, or annulus, in order to reduce self-shielding effects within the lithium, and to further facilitate tritium loading and containment within the zirconium. Additionally, a stainless steel 316 cladding surrounds the target rods, to further reduce outgassing of helium. The core is made up of 6480 fuel pins, enriched to 4.75% wt% U-235/U, and 3660 lithium pins in mixed assemblies arranged in hexagonal lattices, with the lithium enriched to 75% lithium-6, and a total lithium loading of approximately 70 kg. An accelerator is used as a neutron source, firing 800 MeV protons at a liquid lead target loop. Neutronics analysis and burnup calculation were performed with the aid of MCNP6. (authors)

07 ISOTOPE AND RADIATION SOURCES↗

Identified corrosion and erosion mechanisms in SCO2 Brayton Cycles.

Supercritical Carbon Dioxide (S-CO2) is an efficient and flexible working fluid for power production. Research to interface S-CO2 systems with nuclear, thermal solar, and fossil energy sources is currently underway. To proceed, we must address concerns regarding compatibility of materials, at high temperature, and compatibility between significantly different heat transfer fluids. Dry, pure S-CO2 is thought to be relatively inert [1], while the addition of ppm levels of water and oxygen result in formation of a protective chromia layer and iron oxide [2]. Thin oxides are favorable as diffusion barriers, and for their minimal impact on heat transfer. While S-CO2 is typically understood to be the secondary fluid, many varieties of primary fluids exist for nuclear applications. Molten salts, for use in the Molten Salt Reactor concept, are given as an example to contrast the materials requirements of primary and secondary fluids. Thin chromia layers are soluble in molten salt systems (nitrate, chloride, and fluoride based salts) [3-8], making materials selection for heat exchangers a precarious balancing act between high temperature oxidation (S-CO2) and metal dissolution (salt side of heat exchanger). Because concerns have been raised regarding component lifetimes, S-CO2 work has begun to characterize starting materials and to establish a baseline by analysis of 1) as-received stainless steel piping, and 2) piping exposed to S-CO2 under typical operating conditions with Sandia National Laboratories Brayton systems. A second issue discovered by SNL involves substantial erosion in the turbine blade and inlet nozzle. It is believed that this is caused by small particulates that originate from different materials around the loop that are entrained by the S-CO2 to the nozzle, where they impact the inlet nozzle vanes, causing erosion. We believe that, in some way, this is linked to the purity of the S-CO2, the corrosion contaminants, and the metal particulates that are present in the loop and its components.

Fleming, Darryn D.↗

Machine learning assisted phase and size-controlled synthesis of iron oxide particles

Synthesis of iron oxides with specific phases and particle sizes is a crucial challenge in various fields, including materials science, energy storage, biomedical applications, environmental science, and earth science. However, despite significant advances in this area, much of the current palette of particle outcomes has been based on time-consuming trial-and-error exploration of synthesis conditions. The present study was designed to explore a very different approach to 1) predict the outcome of synthesis from specified reaction parameters based on using machine learning (ML) techniques, and 2) correlate sets of parameters to obtain products with desired outcomes by a newly designed recommendation algorithm. To achieve this, four ML algorithms were tested, namely random forest, logistic regression, support vector machine, and k-nearest neighbor. Among the models, random forest outperformed the others, attaining 96% and 81% accuracy when predicting the phase and size of iron oxide particles in the test dataset. Surprisingly, the permutation feature importance analysis revealed that volume, which may strongly relate to pressure, was one of the important features, along with precursor concentration, pH, temperature, and time, influencing the phase and size of iron oxide particles during synthesis. To verify the robustness of the random forest models, prediction and experimental results were compared based on 24 randomly generated methods in additive and non-additive systems not included in the datasets. The predictions of product phase and particle size from the models agreed well with the experimental results. Furthermore, a searching and ranking algorithm was developed to recommend potential synthesis parameters for obtaining iron oxide products with the desired phase and particle size from previous studies in the dataset. Furthermore, this study lays the foundation for a closed-loop approach in materials synthesis and preparation, beginning with suggesting potential reaction parameters from the dataset and predicting potential outcomes, followed by conducting experiments and analyses, and ultimately enriching the dataset.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Overlooked Potential of Sulfated Zirconia: Reexamining Solid Superacidity Toward the Controlled Depolymerization of Polyolefins

Closed-loop recycling via an efficient chemical process can help alleviate the global plastic waste crisis. However, conventional depolymerization methods for polyolefins, which compose more than 50% of plastics, demand high temperatures and pressures, employ precious noble metals, and yield complex mixtures of products limited to single-use fuels or oils. Superacidic sulfated zirconia (SZrO) with Hammet Acidity Functions (H 0 ) = -12 (i.e., stronger than 100% H 2 SO 4 ) is an industrially deployed heterogeneous catalyst capable of activating hydrocarbons under mild conditions and is shown to decompose polyolefins at ambient pressure and temperatures near 200 °C. Additionally, confinement of active sites in porous supports is known to radically increase selectivity, coking and sintering resistance, and acid site activity, presenting a possible approach to low-energy polyolefin depolymerization. However, a critical examination of the literature on SZrO led us to a surprising conclusion: despite 40 years of catalytic study, engineering, and industrial use, the surface chemistry of SZrO is poorly understood. Ostensibly spurred by SZrO's impressive catalytic activity, the application-driven study of SZrO has resulted in deleterious ambiguity in requisite synthetic conditions and insufficient characterization of acidity, porosity, and active site structure. Here, this ambiguity has produced significant knowledge gaps surrounding the synthesis, structure, and mechanisms of hydrocarbon activation for optimized SZrO, stunting the potential of this catalyst in olefin cracking and other industrially relevant reactions, such as isomerization, esterification, and alkylation. Toward mitigating these long extant issues, we herein identify and highlight these current shortcomings and knowledge gaps, propose explicit guidelines for characterization of and reporting on characterization of solid acidity, and discuss the potential of pore-confined superacids in the efficient and selective depolymerization of polyolefins.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Outdoor Test Bed Performance of a Power Line Sensor Using a Real-Time Event Simulator

This report summarizes the design and application of an outdoor power line sensor testbed (OPLST) with a real-time simulator and power meter to compare a potential transformer (PT) and current transformer (CT) versus an advanced line-post sensor. The OPLST was created to validate advanced medium-voltage (20/34.5 kV) outdoor power line sensors used in electrical distribution systems. Electrical utilities have installed metering and relay-protection transformers like PTs and CTs for several decades. The PTs/CTs are iron core measurement transformers based on the electromagnetic induction principle and provide reliable data in normal grid operation. However, new outdoor power line sensors (OPLS) using other technologies like voltage divider, Rogowski coil and optical principles have become available and may have favorable performance and costs compared to PTs/CTs. Therefore, the importance of testing these technologies with the PT/CT, to compare the measured phase voltage/current at different power grid scenarios is crucial to understand the performance of these new OPLS. For this study a G&W Electric Model CVS-36-O power line sensor was chosen as the OPLS to test with voltage/current signals. An OPAL-RT Technologies Model OP4510 real-time simulator and Schweitzer Engineering Laboratories Model SEL-735 power meter were installed with the 20/34.5 kV OPLST to compare the measured transient events collected from an advanced OPLS and the PT/CT. This system is installed at the Distributed Energy Communications and Control (DECC) lab, Oak Ridge National Laboratory (ORNL). The simulator generated different power grid scenarios (electrical faults, capacitor bank operation, service restoration, etc.), and its analog-output signals were connected to the voltage/current amplifiers that feed the 20/34.5 kV aerial cable loop through the PT/CT devices. Additional PT/CT devices were also wired with the medium voltage aerial cable loop to measure the phase current/voltage signals and server as references. After each test, common format for transient data exchange (COMTRADE) files were collected from the SEL-735 power meter and used to compare the performance of the OPLS with the PT/CT. The behavior of analog signals, harmonic components, total harmonic distortion and crest factors were assessed and found favorable for the G&W sensor as compared to the reference PT/CT.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Developing Highly Sensitive Micro-Biosensors for in-situ Monitoring Mercury and Chromium(IV) Contaminants by Genetically-evolving and Computer-designing Metal-binding Proteins

Mercury has been well known as an environmental pollutant to the environment and to cause serious effects on human health for several decades. To effectively control mercury pollution and reduce mercury damages, the sensitive determination of mercury is essential. Currently, many different types of sensor-based assays have been developed, while the whole-cell biosensor has been gaining increasingly attentions due to its easy reproducibility and the possibility to greatly reduce the cost. However, significant improvements on the specificity, sensitivity, stability and simplicity of the whole-cell biosensor are still needed prior to its eventual commercialization. Sponsored by US Department of Energy under the contract agreement DE-FG02-07ER64410, we applied the special synthetic biology and directed evolution strategies to improve the effectiveness and performance of whole-cell biosensors. We have constructed different whole-cell biosensors for the mercuric ion and methylmercury detection with metalloregulator MerR, fluorescent protein mCherry and organomercurial lyase MerB. By introducing the mercuric transporter MerT, we were able to increase the detection sensitivity of whole-cell biosensors by at least one fold. By introducing the bio-amplification genetic circuit based on the gene cascade expression system of $P_{RM-}cI$ from bacteriophage λ and Pm-XylS2 from Pseudomonas putida, we have increased the detection sensitivity of whole-cell biosensors by 1~2 folds in our tested conditions. With the directed evolution of MerR and subsequent high-throughput screening via color assay and microplate screening, we have dramatically increased the detection sensitivity by up to 10 folds at low concentration of mercury (II) of 1-10nM. Structural modeling and computational analysis of the mutated MerR showed that many mutations could cause the change of a loop to helix, which could be responsible for the increased mercury sensitivity.

02 PETROLEUM↗

Noncommutative fermions and quarkonia decays

The recent introduction of a deformed nonminimal version of the noncommutative standard model in the enveloping-algebra approach, having a one-loop renormalizable gauge sector involving a higher order gauge term, motivates us to consider the possibility of extending the fermion sector with additional deformations, i.e. higher order fermionic terms. Since the renormalizability properties of the fermion sector of the model are not yet fully known, we work with an effective fermion Lagrangian, which includes noncommutative higher order terms involving a contraction with the noncommutative {theta} tensor aside from the star products, so that these terms annihilate in the commutative limit. Some of these terms violate CPT in the weak sector, and some violate CP in the strong and hypercharge sectors. We apply this framework to the re-evaluation of the decay rates of quarkonia (qq{sub 1}=J/{psi}, {upsilon}) into two photons. These decays, which are forbidden in the ordinary standard model, had been previously studied as possible signals for noncommutativity, but not in the framework of the better behaved deformed nonminimal version of the noncommutative standard model. Weak CPT or strong-hypercharge CP violating interactions do not contribute to the result. If the parameters of the model take natural values, for the vast majority of configurations the resulting branching ratios are enhanced with respect to their values in the minimal version of the noncommutative standard model. Also for more than half of the parameter space, the rates are larger than the maximal rates that were calculated in the undeformed version of the nonminimal noncommutative standard model. Tuning the dimensionless parameters the predicted branching ratios can fall within the current experimental bounds.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Power Hardware-In-the-Loop Hydropower and Ultracapacitor Hybrid Testbed

Widespread deployment of a proof-of-concept technological solution for power system performance improvement can be accelerated through onsite demonstration and pilot projects. Digital real-time simulation with power hardware-in-the-loop in controlled lab environment is the precursor to de-risk the timely and efficient execution of field demonstration and pilot projects. However, the detailed process of development, characterization, and calibration of such high fidelity simulation testbed needs to be documented in a reproducible and publicly accessible manner to leverage across broader research and development communities. This paper presents such a laboratory testbed to study black start capability of a run-of-river hydro + ultracapacitor hybrid system. Beside the high-fidelity model of the islanded grid with hydropower unit, the testbed includes the energy storage, grid following inverter, and grid emulator hardware. Several aspects such as storage characterization, control and various parameter settings necessary to capture frequency transients during load restoration are described in a comprehensive manner, which led to an effective and timely execution of black start field demonstration with an actual hydropower plant.

13 HYDRO ENERGY↗

Dynamics of Organophosphate‐Induced Structural Changes in Acetylcholinesterase Revealed by Time‐Resolved Small‐Angle X‐Ray Scattering and Inelastic Neutron Scattering

Organophosphates (OPs), the active compounds in nerve agents and insecticides such as paraoxon (POX), exert their toxic effects by irreversibly inhibiting acetylcholinesterase (AChE). Currently available antidotes for OP toxicity can reactivate AChE, but reactivation rates are slow which can lead to irreversible nervous system damage or death. We hypothesize that better antidotes with accelerated reactivation rates can be developed by understanding the structural dynamics of OP‐AChE conjugates. Previous steady‐state small‐angle X‐ray scattering (SAXS) experiments showed that POX and certain other OPs induce quaternary structural changes in human AChE (hAChE) that were reversible by oxime antidotes. To characterize the dynamics of these OP‐induced structural changes we have used time‐resolved SAXS (TR‐SAXS) and inelastic neutron scattering (INS). Stopped‐flow TR‐SAXS experiments were performed at BL‐4 at the Stanford Synchrotron Radiation Lightsource by mixing a molar excess of POX (500 μM) with hAChE (50 μM). Scattering data were collected every 20 msec during the first 1000 msec after mixing. Changes in the solution structure of hAChE during this period occurred with k obs = 0.13(±0.01) s −1 . This rate of structural change is comparable to the rate of hAChE inactivation observed using biochemical assays. INS data were collected at the Cold Neutron Chopper Spectrometer at the Spallation Neutron Source at Oakridge National Laboratory using 100 mg samples of hAChE and POX‐hAChE that were lyophilized and rehydrated in D 2 O. INS data collected at 120 K (to prevent translational motions) were used to compare the vibrational density states of native and POX‐conjugated hAChE. The POX‐conjugated hAChE exhibited an increased number of vibrational states, particularly those associated with regional motions such as loop dynamics, whereas global collective motions remained unchanged. Molecular dynamics simulations were used to simulate the vibrational spectra and identify the region(s) in hAChE that contributed to the differences in the INS experimental data. In aggregate, these studies provide experimental evidence for OP conjugate‐induced changes in hAChE dynamics that has to be considered in the design of antidotes for OP poisoning that have improved efficacy and patient outcomes. Support or Funding Information This work was supported by the CounterACT Program, National Institutes of Health Office of the Director, Grant 1U01NS083451 from NINDS, and by grants to SSRL and ORNL from the U.S. Department of Energy, and the National Institutes of Health. This abstract is from the Experimental Biology 2018 Meeting. There is no full text article associated with this abstract published in The FASEB Journal .

Blumenthal, Donald K.↗

Liquid Salt Heat Exchanger Technology for VHTR Based Applications

The objective of this research is to evaluate performance of liquid salt fluids for use as a heat carrier for transferring high-temperature process heat from the very high-temperature reactor (VHTR) to chemical process plants. Currently, helium is being considered as the heat transfer fluid; however, the tube size requirements and the power associated with pumping helium may not be economical. Recent work on liquid salts has shown tremendous potential to transport high-temperature heat efficiently at low pressures over long distances. This project has two broad objectives: To investigate the compatibility of Incoloy 617 and coated and uncoated SiC ceramic composite with MgCl 2 -KCl molten salt to determine component lifetimes and aid in the design of heat exchangers and piping; and, To conduct the necessary research on the development of metallic and ceramic heat exchangers, which are needed for both the helium-to-salt side and salt-to-process side, with the goal of making these heat exchangers technologically viable. The research will consist of three separate tasks. The first task deals with material compatibility issues with liquid salt and the development of techniques for on-line measurement of corrosion products, which can be used to measure material loss in heat exchangers. Researchers will examine static corrosion of candidate materials in specific high-temperature heat transfer salt systems and develop an in situ electrochemical probe to measure metallic species concentrations dissolved in the liquid salt. The second task deals with the design of both the intermediate and process side heat exchanger systems. Researchers will optimize heat exchanger design and study issues related to corrosion, fabrication, and thermal stresses using commercial and in-house codes. The third task focuses integral testing of flowing liquid salts in a heat transfer/materials loop to determine potential issues of using the salts and to capture realistic behavior of the salts in a small scale prototype system. This includes investigations of plugging issues, heat transfer, pressure drop, and the corrosion and erosion of materials in the flowing system.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Autonomous System Subversion Tactics: Prototypes and Recommended Countermeasures

One of the fielding requirements for Advanced and Small Modular Reactors (AR/SMR) is the ability to support remote and autonomous operations. Autonomous Control Systems (ACS) are found on platforms such as Autonomous Space Vehicles, Cruise Missiles, and advanced driver-assistance systems. Each of these ACS implementations depends upon a set of decision support subsystems responsible for supporting Autonomous Mission Managers (names vary based upon field and author preferences). These Autonomous Mission Managers receive inputs from system sensors (e.g., LIDAR collection from an automobile travelling down a street; transients from a nuclear reactor), and perform a set of classifications (e.g., Red Traffic Light; Small Pedestrian at 10m; Load Rejection; Single Coolant Pump Trip), and then use these classifications in combination with recommendation algorithms to achieve platform goals (e.g., Stop the Vehicle at the Traffic Light, Avoid the Small Pedestrian; Trip the Reactor to prevent a Safety Event). The design, implementation, and fielding of an ACS capability will alter the cyber-attack surface such that existing risk management plans will need to be updated to include how to protect and defend against data-science and decision-support-system attack classes. These attack classes would include protection of the design and training environments where algorithm selection and testing and training data would be obvious attack vectors. These attack classes would also require an informed set of detection and response procedures to identify anomalous behaviors and document best practices for anomaly assessment and vulnerability mitigation and remediation. Last year we published a Cyber Threat Assessment Methodology for Autonomous and Remote Operations for AR/SMRs along with a companion publication on Cyber Attack and Defense Use Cases. The focus of the methodology was on describing and enumerating ACS processes, components, and functions such that security engineers could: evaluate subversion options against the target; identify threat actor attributes and capabilities derived from each subversion option; and identify security controls and response countermeasures. The Use Cases document offered detailed methodology examples including an assessment of a Military Base SMR, an Autonomous System Decision Loop, and implementation of AR/SMR Machine Learning algorithms. Our proposal at the end of last year was to focus on implementation of subversion prototypes related to the last Use Case area: AR/SMR Machine Learning (ML) Algorithms. We included six attack scenarios in our Use Cases paper: a Poisoning Attack against ML functions implemented using an FPGA; a Trojaning Attack against ML classifiers exploiting the excitability of Nuclear Engineers; a Backdooring Attack against ML Training environments to ensure persistence of an attack vector; a False Positive Evasion Attack against multi-factor Access Control Systems using clever inputs; an Inference Attack against ML models by an Insider with access to the Operational environment; and an Adversarial Reprogramming Attack against a Material Access Control Video Surveillance System. At the beginning of this year these six attack scenarios were provided to our research teams at Georgia Tech and Idaho State University and each team successfully implemented a subversion attack against a ML implementation to include transient misclassifications. While this is a notable outcome from this type of research, this paper offers the reader insight into not only how to structure and execute these types of attacks, but into the thought process behind how the researcher investigated the problem space, performed initial algorithm implementation, and the trial-and-error behind arriving at the successful subversion prototypes. We include in this paper a set of associated Scenarios on how these subversion prototypes could be implemented and an initial set of guidance for AR/SMR architects, Nuclear Regulators, and Cyber Defenders to implement awareness and defense capabilities into their current operational portfolios.

42 ENGINEERING↗

Enhancing VHTR Passive Safety and Economy with Thermal Radiation Based Direct Reactor Auxiliary Cooling System

One of the most important requirements for Gen. IV Very High Temperature Reactor (VHTR) is passive safety. Currently all the gas cooled version of VHTR designs use Reactor Vessel Auxiliary Cooling System (RVACS) for passive decay heat removal. The decay heat first is transferred to the core barrel by conduction and radiation, and then to the reactor vessel by thermal radiation and convection; finally the decay heat is transferred to natural circulated air or water systems. RVACS can be characterized as a surface based decay heat removal system. The RVACS is especially suitable for smaller power reactors since small systems have relatively larger surface area to volume ratio. However, RVACS limits the maximum achievable power level for modular VHTRs due to the mismatch between the reactor power (proportional to volume) and decay heat removal capability (proportional to surface area). When the relative decay heat removal capability decreases, the peak fuel temperature increases, even close to the design limit. Annular core designs with inner graphite reflector can mitigate this effect; therefore can further increase the reactor power. Another way to increase the reactor power is to increase power density. However, the reactor power is also limited by the decay heat removal capability. Besides the safety considerations, VHTRs also need to be economical in order to compete with other reactor concepts and other types of energy sources. The limit of decay heat removal capability set by using RVACS has affected the economy of VHTRs. A potential alternative solution is to use a volume-based passive decay heat removal system, called Direct Reactor Auxiliary Cooling Systems (DRACS), to remove or mitigate the limitation on decay heat removal capability. DRACS composes of natural circulation loops with two sets of heat exchangers, one on the reactor side and another on the environment side. For the reactor side, cooling pipes will be inserted into holes made in the outer or inner graphite reflector blocks. There will be gaps between these cooling pipes and their corresponding surrounding graphite surfaces. Graphite has an excellent heat conduction property. By taking advantage of this feature, we can have a volume-based method to remove decay heat. The scalability can be achieved, if needed, by employing more rows of cooling pipes to accommodate higher decay heat rates. Since heat can easily conduct through the graphite regions between the holes made for the cooling pipes, those cooling pipes located further away from the active core region can still be very effective in removing decay heat. By removing the limit on the decay heat removal capability due to the limited available surface area as in a RVACS, the reactor power and power density can be significantly increased, without losing the passive heat removal feature. This paper will introduce the concept of using DRACS to enhance VHTR passive safety and economics. Three design options will be discussed, depending on the cooling pipe locations. Analysis results from a lumped volume based model and CFD simulations will be presented.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

$H \to \gamma\gamma$ search and direct photon pair production differential cross section

At a hadron collider, diphoton (γγ) production allows detailed studies of the Standard Model (SM), as well as as searches for new phenomena, such as new heavy resonances, extra spatial dimensions or cascade decays of heavy new particles. Within the SM, continuum γγ+X production is characterized by a steeply-falling γγ mass spectrum, on top of which a heavy resonance decaying into γγ can potentially be observed. In particular, this is considered one of the most promising discovery channels for a SM Higgs boson at the LHC, despite the small branching ratio of BR (H → γγ) {approx} 0.2% for 110 < M Higgs < 140 GeV. At the Tevatron, the dominant SM Higgs boson production mechanism is gluon fusion, followed by associated production with a W or Z boson, and vector boson fusion. While the SM Higgs production rate at the Tevatron is not sufficient to observe it in the γγ mode, the Hgg and Hγγ couplings, being loop-mediated, are particularly sensitive to new physics effects. Furthermore, in some models beyond the SM, for instance, fermiophobic Higgs, with no couplings to fermions, the BR (H → γγ) can be enhanced significantly relative to the SM prediction, while has the SM-like production cross sections except the gluon fusion is absent. In this thesis, we present a search for a light Higgs boson in the diphoton final state using 4.2 ± 0.3 fb -1 of the D0 Run II data, collected at the Fermilab Tevatron collider from April 2002 to December 2008. Good agreement between the data and the SM background prediction is observed. Since there is no evidence for new physics, we set 95% C.L. limits on the production cross section times the branching ratio (σ x BR(H → γγ)) relative to the SM-like Higgs prediction for different assumed Higgs masses. The observed limits (σ(limit)/σ(SM)) range from 11.9 to 35.2 for Higgs masses from 100 to 150 GeV, while the expected limits range from 17.5 to 32.0. This search is also interpreted in the context of the particular fermiophobic Higgs model. The corresponding results have reached the same sensitivity as a single LEP experiement, setting a lower limit on the fermiophobic Higgs of M h f > 102.5 GeV (M h f > 107.5 GeV expected). We are slightly below the combined LEP limit (M h f > 109.7 GeV). We also provide access to the M h f > 125 GeV region which was inaccessible at LEP. During the study, we found the major and irreducible background direct γγ (DPP) production is not well modelled by the current theoretical predictions: RESBOS, DIPHOX or PYTHIA. There is ~20% theoretical uncertainty for the predicted values. Thus, for our Higgs search, we use the side-band fitting method to estimate DPP contribution directly from the data events. Furthermore, DPP production is also a significant background in searches for new phenomena, such as new heavy resonances, extra spatial dimensions, or cascade decays of heavy new particles. Thus, precise measurements of the DPP cross sections for various kinematic variables and their theoretical understanding are extremely important for future Higgs and new phenomena searches. In this thesis, we also present a precise measurement of the DPP single differential cross sections as a function of the diphoton mass, the transverse momentum of the diphoton system, the azimuthal angle between the photons, and the polar scattering angle of the photons, as well as the double differential cross sections considering the last three kinematic variables in three diphoton mass bins, using 4.2 fb -1 data. These results are the first of their kind at D0 Run II, and in fact the double differential measurements are the first of their kind at Tevatron. The results are compared with different perturbative QCD predictions and event generators.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗