Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

FFT-based model for irradiated aggregate microstructures in concrete

The concrete biological shield of light water reactors is exposed to neutron and gamma irradiation throughout its lifetime, which results in the long-term degradation of the concrete’s mechanical properties. Under neutron irradiation, the concrete’s aggregates are subjected to radiation-induced volumetric expansion (RIVE), which strongly depends on the mineral content of the aggregate and exhibits the largest expansion in silicate-bearing minerals. In this work, the authors used the fast Fourier transform-based code Microstructure-Oriented Scientific Analysis of Irradiated Concrete (MOSAIC) in 2D to model the expansion of five different aggregates provided by the Japan Concrete Aging Management Program (JCAMP). Comparable rock specimens were irradiated at the JEEP-II test reactor. The model uses realistic aggregate microstructure reconstruction based on high-resolution characterization images. The model accounts for anisotropic RIVE, thermal expansion, and the associated initiation and propagation of damage. The RIVE models are calibrated based on expansion data in the literature. The authors assume that damage occurs exclusively at interfaces between the particles that compose an aggregate and that these interfaces also exhibit swelling. Using a micromechanical model, the evolution of Young’s modulus with RIVE is calculated for each aggregate and compared with Russian irradiation data. The modeled linear expansion agrees well with the experimentally measured expansion. Furthermore, the model also predicts that anisotropic RIVE and thermal expansion result in an earlier onset of damage with neutron fluence than in the isotropic case.

36 MATERIALS SCIENCE↗

New In-pile Instrumentation to Support Fuel Cycle Research and Development

New and enhanced nuclear fuels are a key enabler for new and improved reactor technologies. For example, the goals of the next generation nuclear plant (NGNP) will not be met without irradiations successfully demonstrating the safety and reliability of new fuels. Likewise, fuel reliability has become paramount in ensuring the competitiveness of nuclear power plants. Recently, the Office of Nuclear Energy in the Department of Energy (DOE-NE) launched a new direction in fuel research and development that emphasizes an approach relying on first principle models to develop optimized fuel designs that offer significant improvements over current fuels. To facilitate this approach, high fidelity, real-time, data are essential for characterizing the performance of new fuels during irradiation testing. A three-year strategic research program is proposed for developing the required test vehicles with sensors of unprecedented accuracy and resolution for obtaining the data needed to characterize three-dimensional changes in fuel microstructure during irradiation testing. When implemented, this strategy will yield test capsule designs that are instrumented with new sensor technologies for the Advanced Test Reactor (ATR) and other irradiation locations for the Fuel Cycle Research and Development (FC R&D) program. Prior laboratory testing, and as needed, irradiation testing, of these sensors will have been completed to give sufficient confidence that the irradiation tests will yield the required data. Obtaining these sensors must draw upon the expertise of a wide-range of organizations not currently supporting nuclear fuels research. This document defines this strategic program and provides the necessary background information related to fuel irradiation testing, desired parameters for detection, and an overview of currently available in-pile instrumentation. In addition, candidate sensor technologies are identified in this document, and a list of proposed criteria for ranking these technologies. A preliminary ranking of candidate technologies is performed to illustrate the path forward for developing real-time instrumentation that could provide the required data for the FC R&D program. This draft document is a starting point for discussion with instrumentation experts and organizations. It is anticipated that the document will be used to stimulate discussions on a wide-range of sensor technologies and to gain consensus with respect to the path forward for accomplishing the goals of this research program.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Solid electrolytes for solid-state and lithium-sulfur batteries

The stringent demands placed on batteries by emerging vehicle technologies such as plug-in and battery electric vehicles suggest that improvements in the safety and performance of electrochemical energy storage devices, as well as concurrent reductions in their cost, are highly desirable. Current strategies for improving performance have largely focused on Li-ion battery chemistries. In this project went beyond the state of the art by pursuing electrolyte chemistries that will enable the use of Li metal anodes and sulfur cathodes, either concurrently in a solid state Li-S battery, or as a means to achieve a Li metal anode which is stable upon cycling. More specifically, our effort advanced strategies to enable Li metal anodes for myriad beyond Li-ion chemistries . LLZO garnet (Li 7 La 3 Zr 2 O 12 ) is the first bulk-scale ceramic electrolyte to exhibit the combination of superionic conductivity (1mS/cm at 298K), high shear modulus (61 GPa) to suppress Li dendrite penetration, and apparent electrochemical stability (0-6V vs Li/Li + ), thus enabling Li metal anodes. However, to date there are no reports confirming LLZO can tolerate current densities > 1mA/cm 2 , thus demonstrating relevance to PHEV/EV batteries. Our goal was to investigate the mechanisms that govern the Li-LLZO interfacial stability as a function of current density. We determined that defects in polycrystalline LLZO reduce the critical current density (CCD). Primarily contaminants on the LLZO surface and grain boundaries were the primary defects the limited the CCD. Using our experience with synthesis and processing (Sakamoto and Wolfenstine) and sophisticated materials characterization (Nanda), we precisely controlled atomistic and microstructural defects and correlated their effects on controlling the critical current density. These data fed into multi-scale computation models (Siegel and Monroe) to isolate and quantify the roles that each defect played in controlling the critical current density. Bridging this knowledge gap allowed us to demonstrate that LLZO can withstand > 1mA/cm 2 .

25 ENERGY STORAGE↗

U-10Mo Mechanical Property Study Results

A uranium-10wt% molybdenum billet was cast using a vacuum induction meting furnace. The uranium was retrieved from ZPPR stockpiles and had previously been coated with a polymeric coating to prevent oxidation. The coating was removed by mechanically removing the exterior surfaces. After casting total carbon analysis, tensile testing, and microstructural testing was performed. Based on the characterization results ZPPR stockpile depleted uranium can be used as a source of depleted uranium if all coating materials are fully removed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comprehensive Characterization of Helium-Induced Degradation of the Friction Stir Weld on Neutron-Irradiated 304L Stainless Steel

The report describes new experimental results on the mechanical performance of the friction stir welds made on neutron-irradiated 304L stainless steel with helium. The report focuses on helium-related issues (e.g., the helium-induced degradation in the welded joint), aiming at the need to repair irradiated components of nuclear power plants. The friction stir welds analyzed here were previously produced at the US Department of Energy’s Oak Ridge National Laboratory, and initial characterization work was performed, mostly addressing the microstructure and if macroscopic cracks and helium bubbles present. The present work attempts to perform a more comprehensive study to assess mechanical performance (i.e., microhardness distribution, tensile properties, tensile deformation behaviors, and fractography analysis).

36 MATERIALS SCIENCE↗

Final Report on Characterization of Irradiated Sensors and Coupling Adhesive Bonds

This report summarizes characterization via scanning/transmission electron microscopy of the microstructures of the unirradiated and irradiated piezoelectric ultrasonic sensor/aluminum substrate assemblies using four commercially available inorganic coupling adhesives to bond two types of piezoelectric crystals to the substrates. The sample assemblies were irradiated in the PULSTAR reactor at NC State University and ultrasonic data was collected in-situ. ORNL LAMDA Laboratory capabilities were utilized to perform pre- and post-irradiation examination of the sensor assemblies. This document summarizes the PIE performed at the ORNL LAMDA laboratory. The results of the PIE described in this report are consistent with the ultrasonic data collected during irradiation – in particular, high temperature epoxy adhesive seemed to provide the best coupling as compared to the refractory ceramic adhesives. It was determined that the quality of the sensor-adhesive-substrates governed the ultrasonic performance of the sensors. It was also apparent that irradiation did not significantly affect bond quality, which is also supported by the ultrasonic data collected during irradiation. A more comprehensive DOE NSUF Final Report including details of materials selection, sample fabrication, initial ultrasonic testing, irradiation and in-situ ultrasonic testing, positron annihilation lifetime spectroscopy and doppler broadening spectroscopy performed at EPRI and NC State University will be published at the conclusion of the project.

36 MATERIALS SCIENCE↗

High Strength and Deformation Mechanisms of A l0.3 CoCrFeNi High-Entropy Alloy Thin Films Fabricated by Magnetron Sputtering

Recently, high-entropy alloy thin films (HEATFs) with nanocrystalline structures and high hardness were developed by magnetron sputtering technique and have exciting potential to make small structure devices and precision instruments with sizes ranging from nanometers to micrometers. However, the strength and deformation mechanisms are still unclear. In this work, nanocrystalline Al0.3CoCrFeNi HEATFs with a thickness of ~4 μm were prepared. The microstructures of the thin films were comprehensively characterized, and the mechanical properties were systematically studied. It was found that the thin film was smooth, with a roughness of less than 5 nm. The chemical composition of the high entropy alloy thin film was homogeneous with a main single face-centered cubic (FCC) structure. Furthermore, it was observed that the hardness and the yield strength of the high-entropy alloy thin film was about three times that of the bulk samples, and the plastic deformation was inhomogeneous. Our results could provide an in-depth understanding of the mechanics and deformation mechanism for future design of nanocrystalline HEATFs with desired properties.

36 MATERIALS SCIENCE↗

Review of Swift Heavy Ion Irradiation Effects in CeO2

Cerium dioxide (CeO2) exhibits complex behavior when irradiated with swift heavy ions. Modifications to this material originate from the production of atomic-scale defects, which accumulate and induce changes to the microstructure, chemistry, and material properties. As such, characterizing its radiation response requires a wide range of complementary characterization techniques to elucidate the defect formation and stability over multiple length scales, such as X-ray and neutron scattering, optical spectroscopy, and electron microscopy. In this article, recent experimental efforts are reviewed in order to holistically assess the current understanding and knowledge gaps regarding the underlying physical mechanisms that dictate the response of CeO2 and related materials to irradiation with swift heavy ions. The recent application of novel experimental techniques has provided additional insight into the structural and chemical behavior of irradiation-induced defects, from the local, atomic-scale arrangement to the long-range structure. However, future work must carefully account for the influence of experimental conditions, with respect to both sample properties (e.g., grain size and impurity content) and ion-beam parameters (e.g., ion mass and energy), to facilitate a more direct comparison of experimental results.

42 ENGINEERING↗

Machining Test Specimens from Harvested Zion RPV Segments for Through Wall Attenuation Studies

The decommissioning of the Zion Units 1 and 2 Nuclear Generating Station (NGS) in Zion, Illinois presents a special opportunity for developing a better understanding of materials degradation and other issues associated with extending the lifetime of existing Nuclear Power Plants (NPPs) beyond 60 years of service. In support of extended service and current operations of the US nuclear reactor fleet, the Oak Ridge National Laboratory (ORNL), through the Department of Energy (DOE), Light Water Reactor Sustainability (LWRS) Program, is coordinating and contracting with Zion Solutions, LLC, a subsidiary of Energy Solutions, the selective procurement of materials, structures, and components from the decommissioned reactors. In this paper, we will discuss the acquisition of segments of the Zion Unit 2 Reactor Pressure Vessel (RPV), the cutting of these segments into sections and blocks from the beltline and upper vertical welds and plate material, the current status of machining those blocks into mechanical (Charpy, compact tension, and tensile) test specimens and coupons for chemical and microstructural (TEM, APT, SANS, and nano indention) characterization, as well as the current test plans and possible collaborative projects. Access to service-irradiated RPV welds and plate sections will allow through wall attenuation studies to be performed, which will be used to assess current radiation damage models (Rosseel et al. (2012) and Rosseel et al. (2015)).

Attenuation↗

Hydrothermal corrosion studies on nitride fuels

Uranium mononitride (UN) has been identified as a candidate nuclear fuel for use in the current US light water reactor (LWR) fleet as well as in next generation nuclear plants (NGNP), largely due to its high uranium density and thermal conductivity. However, its hydrothermal corrosion performance in accident scenarios has not been thoroughly investigated. In this work, UN was synthesized using a hydride-de-hydride-nitride thermal synthesis route prior to sintering into dense compacts (> 90% TD). The compacts were corroded in a water filled autoclave up to 350 Celsius degrees and 125 atm. The kinetics of corrosion were characterized through phase analysis, mass loss, and microstructural analysis. The phases observed after hydrothermal corrosion correspond only to UN, UO{sub 2}, and UN{sub 2}; no U{sub 2}N{sub 3} was observed. Additionally, it appears that nitrogen uptake into the lattice of the solid product is a product of lattice strain and peak broadening, especially of the UN{sub 2} phase. UO{sub 2} appears to nucleate on the surface of the UN-UO{sub 2} monoliths and consumes the UN grain boundaries which suggests that in pure UN, UO{sub 2} formation proceeds from the surface and moves towards the core, but in samples with nominal concentrations of UO{sub 2}, oxidation from hydrolysis occurs throughout the bulk of the monoliths. Furthermore, it was demonstrated here that UN and UN-UO{sub 2} composites perform better than previously reported in the literature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Three-dimensional FIB/EBSD characterization of irradiated HfAl{sub 3}-Al composite

A thermal neutron-absorbing composite comprised of 28.4 vol.% HfAl{sub 3} intermetallic particles in an Al matrix, developed for use in a conduction-cooled thermal neutron filter, will enable fast flux irradiation of materials and fuels in an existing pressurized water test reactor. In this paper, an EBSD-FIB characterization approach is used to observe the microstructural changes of the HfAl{sub 3}-Al composite in response to simulated long-term neutron irradiation. Using a focused ion beam (FIB), the sample was fabricated to 25 μm x 25 μm x 20 μm and mounted on a transmission electron microscopy (TEM) grid. A series of operations were carried out repeatedly on the sample's top surface to prepare it for scanning electron microscopy (SEM). First, a ∼ 100-nm layer was removed by high voltage FIB milling. Then, several cleaning passes were performed on the newly exposed surface using low voltage FIB milling to improve the SEM image quality. The surface was then scanned by Electron Backscattering Diffraction (EBSD) to obtain a two-dimensional image. After 50 to 100 two-dimensional images were collected, the images were stacked to reconstruct a three-dimensional model using DREAM.3D software. Two such reconstructed three dimensional models were obtained from samples of the original and post-irradiation HfAl{sub 3}-Al composite, from which the most significant microstructural change caused by neutron irradiation appears to be the size reduction of both HfAl{sub 3} and Al grains. Possible causes include thermal expansion and related thermal strain from thermal neutron capture. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Characterization of Intrinsic Fiber Optic Temperature Sensors by In-core and Furnace Testing

Increased research and development in nuclear technology has raised the demand for novel sensors and instrumentation to meet data objectives, and survive in different conditions and environments, beyond conventional light water reactor (LWR) environments. Expediting the deployment of advanced nuclear technologies by developing, demonstrating, and qualifying advanced reactor fuel forms necessitates a deeper understanding of how irradiation affects fuels and materials' performance. To achieve a more comprehensive understanding of fuels and materials performance, researchers require more specialized experiments and measurements. The demand for innovative sensors to support nuclear fuel development arises from the complexity of materials' behavior under irradiation and the challenges of deploying instrumentation in Material Test Reactors (MTRs) for irradiation tests. Additionally, measurements of material properties require integrated measurement systems to characterize thermal properties, mechanical properties, chemistry, and microstructure [1]. Among the potential measurement techniques, optical fiber-based sensors have been identified as potential sensors to measure different physical phenomena such as temperature, strain, pressure, and fluid level. Optical fiber sensors have the capability to provide multi-sensing and multiplexing instrumentation, allowing the measurement of different physical parameters within a single sensor configuration, and transmitting data collected at multiple locations through a single fiber. They offer immunity to electromagnetic interference, electrical passivity, compatibility with various sensing methodologies, and cost-effectiveness. Beyond their widespread use in telecommunications, silica fiber-based instruments are utilized in industrial applications, even at temperatures reaching 300?400°C, such as distributed temperature sensing in oil and gas recovery. The Department of Energy (DOE) is interested in using fiber optics to support fuel cycle development [2]. Fiber optics are an excellent candidate for harsh environment sensing, including sensing at very high temperatures (1900oC for sapphire optical fibers). Distributed fiber optic sensing has been deployed in other harsh environments like coal gasification plants [3]. Distributed strain sensing, which operates similarly to distributed temperature sensing, has been deployed to monitor underground mines and fibers have been imbedded in soil to monitor sink-hole development [4][5]. The application of fiber optic sensors to advanced reactor development is a promising area of research.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Breaking Boundaries: Deformation Processing Techniques for the Next Generation of Lightweight and High-Strength Materials

This chapter emphasizes the importance of solid phase processing (SPP) techniques in developing advanced materials for lightweight and high-strength applications. SPP methods like friction stir welding, and shear-assisted processing can create new microstructures and process materials in novel ways. SPP can enhance mechanical performance via various strengthening mechanisms like solid solution supersaturation, Hall-Petch and Orowan effects, and misorientation angle grain boundaries. The potential for in situ alloying or joining of components with near-net shape and low energy inputs, even for immiscible systems with high enthalpies of mixing, is also discussed. The chapter explores the concept of metastability through microstructural manipulation and the role of advanced characterization for atomistic understanding. The formation of metastable grain, shear-driven chemical mixing, and transformation pathways are also discussed. Finally, the emerging trends for SPP and the challenges that need to be addressed before realizing the full potential of these techniques are presented.

Lastovich, Michael↗

Brazing ZrO{sub 2} ceramic to Ti–6Al–4V alloy using NiCrSiB amorphous filler foil: Interfacial microstructure and joint properties

Reliable brazing of ZrO{sub 2} ceramic and Ti–6Al–4V alloy was achieved using NiCrSiB amorphous filler foil. The interfacial microstructure of ZrO{sub 2}/Ti–6Al–4V joints was characterized by scanning electron microscope, energy dispersive spectrometer and micro-focused X-ray diffractometer. The effects of brazing temperature on the interfacial microstructure and joining properties of brazed joints were investigated in detail. Active Ti of Ti–6Al–4V alloy dissolved into molten filler metal and reacted with ZrO{sub 2} ceramic to form a continuous TiO reaction layer, which played an important role in brazing. Various reaction phases including Ti{sub 2}Ni, Ti{sub 5}Si{sub 3} and β-Ti were formed in brazed joints. With an increasing of brazing temperature, the TiO layer thickened gradually while the Ti{sub 2}Ni amount reduced. Shear test indicated that brazed joints tend to fracture at the interface between ZrO{sub 2} ceramic and brazing seam or Ti{sub 2}Ni intermetallic layer. The maximum average shear strength reached 284.6 MPa when brazed at 1025 °C for 10 min. - Graphical Abstract: Interfacial microstructure of ZrO{sub 2}/TC4 joint brazed using NiCrSiB amorphous filler foil was: ZrO{sub 2}/TiO/Ti{sub 2}Ni + β-Ti + Ti{sub 5}Si{sub 3}/β-Ti/Widmanstätten structure/TC4. - Highlights: • Brazing of ZrO{sub 2} ceramic and Ti-6Al-4V alloy was achieved. • Interfacial microstructure was TiO/Ti{sub 2}Ni + β + Ti{sub 5}Si{sub 3}/β/Widmanstätten structure. • The formation of TiO produced the darkening effect of ZrO{sub 2} ceramic. • The highest joining strength of 284.6MPa was obtained.

36 MATERIALS SCIENCE↗

Microstructural characteristics of σ phase and P phase in Ru-containing single crystal superalloys

Microstructural instability caused by topologically close-packed (TCP) phase precipitation restricts the useful compositional range of advanced Ni-base single crystal superalloys in industrial applications. Limited systematic investigations of TCP formers (Cr and Mo) additions on microstructural evolution of both the σ phase and the P phase in Ru-containing single crystal superalloys have been reported. In this study, the microstructural characteristics of σ phase and P phase were investigated in three Ru-containing superalloys with different levels of Cr and Mo additions at 950 °C and 1100 °C by using phase extraction, X-ray diffraction, scanning electron microscope and high resolution transmission electron microscopy. The experimental results indicated that the high level additions of Cr and Mo promoted the formation of σ phase and P phase, respectively. The amount of σ phase was much higher than that of P phase after long term exposure at 950 °C and 1100 °C. The sheet-like σ phase existed in the alloy with higher Cr addition after thermal exposure at 950 °C and 1100 °C for 1000 h, while the needle-like P phase precipitated in high Mo content alloy after thermal exposure at 1100 °C for 1000 h and the intergrowth of σ phase and P phase was observed after thermal exposure at 950 °C for 500 h. Both the σ phase and P phase were enriched in Re, W, Cr and Mo, but the σ phase contained more Re and Cr while the P phase contained more Mo and Ni, and Ru was found in both phases. The nucleation of σ phase was much easier than P phase due to the more ledge steps in the interfacial structure between σ phase and matrix, as well as the higher partitioning ratios of Re, Cr and Mo. This study is helpful to understand the microstructural evolution of σ phase and P phase, and to optimize the alloy design in Ru-containing superalloys. - Highlights: •Microstructures of σ phase and P phase were characterized in detail. •Cr and Mo influenced the precipitation of σ phase and P phase, respectively. •Partitioning ratios and interfacial relationship decided precipitation behaviors.

36 MATERIALS SCIENCE↗

Synthesis of porous Ti–50Ta alloy by powder metallurgy

Highlights: • The proposed preview milling with the next sintering enables the homogeneous porous Ti50Ta (wt).% alloy to be obtained • The α and β nanocrystalline phases were prepared by ball milling. • For the longest sintering time there is complete diffusion of preview milled initial powders • The press and sinter route is proved to be a promising alternative for melted Ti-based biomaterials. - Abstract: The aim of the present study was to assess the possibility of producing porous Ti50Ta (wt%) alloys using powder metallurgy by characterizing the material properties. The influence of the sintering time on the microstructure, mechanical properties, and corrosion behaviour of the produced alloy was investigated. The samples were examined using scanning electron microscopy (SEM), transmission electron microscopy (TEM), optic microscopy, X-ray diffraction (XRD) and nanoindentation methods. The XRD results confirmed that nanocrystalline α and β phases were formed during high-energy ball milling. A longer sintering time of 72 h allowed complete interdiffusion of the elements in the pre-milled initial powders. The sintering time significantly influenced the microstructure and porosity. Additionally, the corrosion resistance of the Ti-Ta samples in Ringer's solution was characterized and differences were observed between the samples sintered at different temperatures. The open-circuit potential (E{sub OCP}) and the corrosion potential (E{sub CORR}) of all samples were similar. The sintered Ti50Ta (wt%) alloy showed better corrosion resistance than equivalent Ti or Ta reference samples. We concluded that these alloys had suitable properties for medical implant applications in the future.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Determination of Thermodynamic Properties of Si-B Alloys

This study establishes the thermodynamic properties of the Si-B binary alloy system. The electromotive force (emf) as a function of temperature (823 K to 923 K) was measured using solid-state electrochemical cells, represented as(−) Pt,Ar/{Si∥CaF_2∥} {Si−B(alloy)}/Ar,Pt(+) Using the experimental emf data obtained from the solid-state heterogeneous phase equilibrium, the activities of Si and B in Si-B alloys were calculated. The integral Gibbs energy of mixing (ΔG{sup M}) of alloys were calculated from the activity of Si and B. A large negative deviation from ideality was found for the integral Gibbs energy of mixing (ΔG{sup M}) of the binary Si-B system. From the activities of Si and B, the Gibbs energies of formation (ΔG{sub f}{sup 0}) of phases present were calculated. The ΔG{sub f}{sup 0} of SiB{sub 3}, the most thermodynamically stable phase, was calculated as − 13.13 ± 0.19 kJ/mole-atoms at 923 K. The heterogeneous phases and microstructure after the equilibrium study of the electrode were characterized using XRD, SEM, and EDS analyses.

36 MATERIALS SCIENCE↗

Characterization, organic modification of wollastonite coated with nano-Mg(OH){sub 2} and its application in filling PA6

Highlights: • Wollastonite is first inorganic modified by coating nano-Mg(OH){sub 2} and then organic modified with silane. • Filling 30% of this composite powder in PA6 the mechanical properties, the heat distortion temperature and oxygen index of the PA6 composites were notably enhanced. - Abstract: Nano-Mg(OH){sub 2} was deposited on the surface of wollastonite (MW) powder with heterogeneous nucleation method and then modified with silane. The microstructure and surface properties of wollastonite (W) and MW powders were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray spectrometry (EDS) and X-ray diffraction (XRD), respectively. The microstructure of W, MW and silane modified MW (SMW) powders were characterized by Fourier translation infrared spectroscopy (FTIR). The mechanical properties, heat distortion temperature (HDT) and oxygen index (OI) of PA6 composites having different fillers were discussed. It was shown that the surface of wollastonite was coated with a layer of 33 nm thickness of Mg(OH){sub 2} grains and the distribution of which was uniform. The number of the hydroxyl groups on the surface of wollastonite powder increased after coated with Mg(OH){sub 2}. Filling 30% of SMW powder in PA6 the mechanical properties, HDT and OI were notably enhanced.

36 MATERIALS SCIENCE↗