Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Relating Vegetation Aerodynamic Roughness Length to Interferometric SAR Measurements

In this paper, we investigate the feasibility of estimating aerodynamic roughness parameter from interferometric SAR (INSAR) measurements. The relation between the interferometric correlation and the rms height of the surface is presented analytically. Model simulations performed over realistic canopy parameters obtained from field measurements in boreal forest environment demonstrate the capability of the INSAR measurements for estimating and mapping surface roughness lengths over forests and/or other vegetation types. The procedure for estimating this parameter over boreal forests using the INSAR data is discussed and the possibility of extending the methodology over tropical forests is examined.

Saatchi, Sassan↗

Orbital SAR and Ground-Penetrating Radar for Mars: Complementary Tools in the Search for Water

The physical structure and compositional variability of the upper martian crust is poorly understood. Optical and infrared measurements probe at most the top few cm of the surface layer and indicate the presence of layered volcanics and sediments, but it is likely that permafrost, hydrothermal deposits, and transient liquid water pockets occur at depths of meters to kilometers within the crust. An orbital synthetic aperture radar (SAR) can provide constraints on surface roughness, the depth of fine-grained aeolian or volcanic deposits, and the presence of strongly absorbing near-surface deposits such as carbonates. This information is crucial to the successful landing and operation of any rover designed to search for subsurface water. A rover-based ground-penetrating radar (GPR) can reveal layering in the upper crust, the presence of erosional or other subsurface horizons, depth to a permafrost layer, and direct detection of near-surface transient liquid water. We detail here the radar design parameters likely to provide the best information for Mars, based on experience with SAR and GPR in analogous terrestrial or planetary environments.

Campbell, B. A.↗

Updated Model of Radar Backscatter for Rough Lunar Craters

We reexamined our radar scattering model for young, rough craters [1] based on unpublished data from the 1980's [2]. Our model for scattering from the lunar surface is a mixing model consisting of varying amounts of diffuse and specular components as shown in Figure 1. The specular component, which consists of only opposite-sense circular (OC) echoes, results from the mirror-like surface and sub-surface layers that are smooth to a tenth of a radar wavelength for large (>10 wavelengths) areas oriented perpendicular to the radar's line-ofsight. The diffuse component, which has both OC and same sense (SC) circular echoes, is associated with either surface roughness (wavelength-sized rocks) or ice, and is assumed to be uniformly bright, with backscatter being proportional to the cosine of the incidence angle. Only diffuse scattering contributes to the SC echoes.

Moon↗

Comparison of caprock pore networks which potentially will be impacted by carbon sequestration projects.

Injection of CO2 into underground rock formations can reduce atmospheric CO2 emissions. Caprocks present above potential storage formations are the main structural trap inhibiting CO2 from leaking into overlying aquifers or back to the Earth's surface. Dissolution and precipitation of caprock minerals resulting from reaction with CO2 may alter the pore network where many pores are of the micrometer to nanometer scale, thus altering the structural trapping potential of the caprock. However, the distribution, geometry and volume of pores at these scales are poorly characterized. In order to evaluate the overall risk of leakage of CO2 from storage formations, a first critical step is understanding the distribution and shape of pores in a variety of different caprocks. As the caprock is often comprised of mudstones, we analyzed samples from several mudstone formations with small angle neutron scattering (SANS) and high-resolution transmission electron microscopy (TEM) imaging to compare the pore networks. Mudstones were chosen from current or potential sites for carbon sequestration projects including the Marine Tuscaloosa Group, the Lower Tuscaloosa Group, the upper and lower shale members of the Kirtland Formation, and the Pennsylvanian Gothic shale. Expandable clay contents ranged from 10% to approximately 40% in the Gothic shale and Kirtland Formation, respectively. During SANS, neutrons effectively scatter from interfaces between materials with differing scattering length density (i.e., minerals and pores). The intensity of scattered neutrons, I(Q), where Q is the scattering vector, gives information about the volume and arrangement of pores in the sample. The slope of the scattering data when plotted as log I(Q) vs. log Q provides information about the fractality or geometry of the pore network. On such plots slopes from -2 to -3 represent mass fractals while slopes from -3 to -4 represent surface fractals. Scattering data showed surface fractal dimensions for the Kirtland formation and one sample from the Tuscaloosa formation close to 3, indicating very rough surfaces. In contrast, scattering data for the Gothic shale formation exhibited mass fractal behavior. In one sample of the Tuscaloosa formation the data are described by a surface fractal at low Q (larger pores) and a mass fractal at high Q (smaller pores), indicating two pore populations contributing to the scattering behavior. These small angle neutron scattering results, combined with high-resolution TEM imaging, provided a means for both qualitative and quantitative analysis of the differences in pore networks between these various mudstones.

54 ENVIRONMENTAL SCIENCES↗

Local Composition and Topography of Nb3Sn Diffusion Coatings on Niobium

The potential for energy savings and for increased gradient continues to bring attention to Nb3Sn-coated niobium as a future SRF cavity technology. We prepared these materials by vapor diffusion coating on polycrystalline and single crystal niobium. The effect of changing substrate preparation, coating parameters, and post-treatment was examined by AFM and SEM/EDS. The AFM data were analyzed in terms of power spectral density (PSD). We found little effect of pre-coating topography on the resulting surface roughness. The PSD curves from the coated samples show some surprising kinship to those obtained from BCP-treated surfaces. SEM/EDS revealed no compositional non-uniformities at the micron scale. Authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177

Pudasaini, U.↗

Predicting Fueled Experiment Swelling and Thermal Expansion Using STAR-CCM+

An experiment being designed at Idaho National Laboratory (INL) has an unusual temperature requirement. The surface temperature must remain above 300 C over the irradiation lifetime. The fuel in this experiment is composed of uranium-nitride (UN) tri-structural-isotropic (TRISO) particles encased in a cylindrical, SiC matrix. Increased swelling of SiC at lower temperatures is the basis for this lower temperature limit. For a typical thermal analysis, the focus is on some upper limit of the center-line temperature. This tends to be a more straight-forward process where the analyst makes a series of worst-case assumptions and demonstrates that the experiment - even under those conditions - cannot exceed the maximum temperature. The model used to ensure the experiment will always have a surface temperature in excess of 300 C has been developed using STAR-CCM+. Notable properties of the simulation include - Full 3D fluid and heat transfer modeling; - Geometry input taken directly from design engineer's CAD files; - Fuel swelling and thermal conductivity as functions of displacements per atom (DPA) and temperature; - Radial thermal expansion of fuel, rodlet, and capsule; - Jump gap and surface roughness implemented using equations from BISON. These things together have yielded a model with sufficient detail to predict minimum surface temperatures with the greatest precision attainable with available data. The only notable approximation is the zirconia insulator, which will actually be a sphere. This particular shape was chosen to expedite meshing, while maintaining a realistic degree of physical contact with adjacent components. Given temperature and irradiation dependent data for thermal conductivity and fuel swelling of a SiC matrix, it was possible to perform an in-depth thermal analysis to find an optimal configuration of radial gas gaps. Of greatest importance was that the fuel surface temperature remain above 300 C. This criteria was met with a healthy margin, even when considering machining tolerances of ±1 mil on the gas gaps.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Progress Toward Evaluating Roughness-Resolved Aerothermodynamic Simulations for the Mars Sample Return Earth Entry System

This work pursues the efficient Navier-Stokes simulation, using NASA’s standard LAURA and DPLR simulation tools, of the flowfield and convective heating resulting from the patterned-roughness surface of the Mars Sample Return (MSR) Earth Entry System (EES). This type of simulation has been infeasible for past NASA missions. However, for EES, the combination of a patterned roughness heatshield approximated with a sinusoidal pattern, the zero degrees angle of attack nominal flow, and the supersonic boundary layer edge Mach number, all combine to make these roughness resolved grid simulations feasible. The patterned roughness and zero degrees angle of attack nominal flow allow the simulation domain to be reduced to a thin axial flowfield slice that captures a minimum of single period of the roughness pattern. With a periodic boundary condition applied along the boundaries of this slice, simulation on the reduced domain is identical to the full domain but with significant cost saving. The supersonic boundary layer edge Mach number prevents the upstream influence, which allows the smooth stagnation region to be frozen. This freezing of the stagnation region flow is required because of the numerical instability resulting from the tight spacing of the grid in the axial direction as the stagnation point is approached. Applying the developed analysis approach to a peak heating EES case results in a roughness augmentation factor for the convective heating of 1.32, which agrees well with correlations that predict values between 1.30 and 1.37. Analysis approach developed in this work provides the framework for future studies of turbulence modeling impacts and the influence of an ablating surface.

Earth Entry System↗

Numerical Investigation of Roughness Effects on Transition on Spherical Capsules

The state of the boundary layer on space re-entry vehicles significantly affects the design of the thermal protection system. However, the physical mechanism that leads to the laminar-turbulent boundary-layer transition on blunt spherical capsules remains an open question in literature. This work numerically assesses the potential of roughness-induced non-modal disturbance growth on re-entry capsules with a spherical-section forebody by optimal transient-growth theory and direct numerical simulation. Two different sets of wind-tunnel experiments are considered. Optimal transient-growth studies have been performed for the blunt capsule experiments at Mach 5.9 in the Hypersonic Ludwieg tube Braunschweig (HLB) of the Technische Universitat Braunschweig. In some of these measurements, the capsule model was equipped with a specifically designed patch of distributed micron-sized surface roughness. The transient-growth results for the HLB capsule are compared to corresponding numerical data for a Mach 6 blunt capsule experiment in the Adjustable Contour Expansion (ACE) facility of the Texas A&M University (TAMU) at lower Reynolds number. Similar trends are observed for both configurations. In particular, a rather low maximum energy gain is noted for the surface temperature conditions of the experiments. It is shown that the surface temperature dependence of the optimal transient-growth results is very similar for both capsule configurations. Moreover, the generation of stationary disturbances by well-defined roughness patches on the capsule surface is studied for the conditions of the HLB experiment using direct numerical simulations (DNS). To help explain the observed laminar-turbulent transition downstream of the roughness patch in some of the HLB capsule experiments, additional simulations were carried out to study the evolution of unsteady perturbations within the steady disturbance flow field due to the roughness patch. However, the DNS did not provide any indication of modal or non-modal disturbance growth in the wake of the roughness patch, and hence, the physical mechanism underlying the observed onset of transition remains unknown.

Hein, Stefan↗

Impact of the ongoing Amazonian deforestation on local precipitation: A GCM simulation study

Numerical simulation experiments were conducted to delineate the influence of in situ deforestation data on episodic rainfall by comparing two ensembles of five 5-day integrations performed with a recent version of the Goddard Laboratory for Atmospheres General Circulation Model (GCM) that has a simple biosphere model (SiB). The first set, called control cases, used the standard SiB vegetation cover (comprising 12 biomes) and assumed a fully forested Amazonia, while the second set, called deforestation cases, distinguished the partially deforested regions of Amazonia as savanna. Except for this difference, all other initial and prescribed boundary conditions were kept identical in both sets of integrations. The differential analyses of these five cases show the following local effects of deforestation. (1) A discernible decrease in evapotranspiration of about 0.80 mm/d (roughly 18%) that is quite robust in the averages for 1-, 2-, and 5-day forecasts. (2) A decrease in precipitation of about 1.18 mm/d (roughly 8%) that begins to emerge even in 1-2 day averages and exhibits complex evolution that extends downstream with the winds. (3) A significant decrease in the surface drag force (as a consequence of reduced surface roughness of deforested regions) that, in turn, affects the dynamical structure of moisture convergence and circulation. The surface winds increase significantly during the first day, and thereafter the increase is well maintained even in the 2- and 5-day averages.

Walker, G. K.↗

Deposition and characterization of molybdenum thin films using dc-plasma magnetron sputtering

Molebdenum (Mo) thin films were deposited on well-cleaned soda-lime glass substrates using DC-plasma magnetron sputtering. In the design of experiment deposition was optimized for maximum beneficial characteristics by monitoring effect of process variables such as deposition power (100–200 W). Their electrical, structural and morphological properties were analyzed to study the effect of these variables. The electrical resistivity of Mo thin films could be reduced by increasing deposition power. Within the range of analyzed deposition power, Mo thin films showed a mono crystalline nature and the crystallites were found to have an orientation along [110] direction. The surface morphology of thin films showed that a highly dense micro structure has been obtained. The surface roughness of films increased with deposition power. The adhesion of Mo thin films could be improved by increasing the deposition power. Atomic force microscopy was used for the topographical study of the films and to determine the roughness of the films. X-ray diffractrometer and scanning electron microscopy analysis were used to investigate the crystallinity and surface morphology of the films. Hall effect measurement system was used to find resistivity, carrier mobility and carrier density of deposited films. The adhesion test was performed using scotch hatch tape adhesion test. Mo thin films prepared at deposition power of 200 W, substrate temperature of 23°C and Ar pressure of 0.0123 mbar exhibited a mono crystalline structure with an orientation along (110) direction, thickness of ∼550 nm and electrical resistivity value of 0.57 × 10{sup −4} Ω cm.

36 MATERIALS SCIENCE↗

Erosion of phosphor bronze under cavitation attack in a mineral oil

Experimental investigations on erosion of a copper alloy, phosphor bronze, under cavitation attack in a viscous mineral oil are presented. The details of pit formation and erosion were studied using scanning electron microscopy. The mean depth of penetration, the variations in surface roughness, and the changes in erosion pit size were studied. Cavitation pits formed initially over the grain boundaries while the surface grains were plastically deformed. Erosion of surface grains occurred largely by ductile fracture involving microcracking and removal in layers. The ratio h/a of the depth h to half width a of cavitation pits increased with test duration from 0.047 to 0.55.

Rao, B. C. S.↗

On estimating total daily evapotranspiration from remote surface temperature measurements

A method for calculating daily evapotranspiration from the daily surface energy budget using remotely sensed surface temperature and several meteorological variables is presented. Vaules of the coefficients are determined from simulations with a one-dimensional boundary layer model with vegetation cover. Model constants are obtained for vegetation and bare soil at two air temperature and wind speed levels over a range of surface roughness and wind speeds. A different means of estimating the daily evapotranspiration based on the time rate of increase of surface temperature during the morning is also considered. Both the equations using our model-derived constants and field measurements are evaluated, and a discussion of sources of error in the use of the formulation is given.

Carlson, Toby N.↗

The coefficient of restitution of ice particles in glancing collisions: Experimental results for unfrosted surfaces

Both Saturn's rings and planetesimal disks are made up of particles in Keplerian orbits. Inelastic collisions between these particles regulate their dynamical evolution and possible aggregation. We present an experiment to simulate glancing collisions in Saturn's rings and in planetesimal disks and thus measure contributions to the energy loss for both normal and tangential velocity components. In this experiment, a spherical iceball mounted on a long-period, two dimensional pendulum is made to impact a flat ice surface in a low-temperature environment. This paper describes the experimental apparatus in detail and presents results for smooth unfrosted surfaces. The energy loss for tangential motion is suprisingly low, indicating that very little friction is present at low impact speeds for relatively smooth ice surfaces and temperatures near 100 K. We have also investigated room-temperature collisions of a rubber ball on a rough surface to understand the energy loss in situations where the tangential friction force is not small. In this analogous case, the energy loss is maximum for impact angles in the range 45 deg-60 deg.

Supulver, Kimberley D.↗

To Land on Europa

The Science Definition Team (SDT) for NASA's Jupiter Icy Moons Orbiter (JIMO) Mission recommends including a lander as an integral part of the science payload of the JIMO Mission. The Europa Surface Science Package (ESSP) could comprise up to 25% of science payload resources. We have identified several key scientific and technical issues for such a lander, including 1) the potential effects of propellant contamination of the landng site, 2) the likely macroscopic surface roughness of potential landing sites, and 3) the desire to sample materials from depths of approximately 1 m beneath the surface. Discussion and consensus building on these issues within the science community is a prerequisite for establishing design requirements.

Shirley, James H.↗

Neutral ion sources in precision manufacturing

Ion figuring of optical components is a relatively new technology that can alleviate some of the problems associated with traditional contact polishing. Because the technique is non contacting, edge distortions and rib structure print through do not occur. This initial investigation was aimed at determining the effect of ion figuring on surface roughness of previously polished or ductile ground ceramic optical samples. This is the first step in research directed toward the combination of a pre-finishing process (ductile grinding or polishing) with ion figuring to produce finished ceramic mirrors. The second phase of the project is focusing on the development of mathematical algorithms that will deconvolve the ion beam profile from the surface figure errors so that these errors can be successfully removed from the optical components. In the initial phase of the project, multiple, chemical vapor deposited silicon carbide (CVD SiC) samples were polished or ductile ground to specular or near-specular roughness. These samples were then characterized to determine topographic surface information. The surface evaluation consisted of stylus profilometry, interferometry, and optical and scanning electron microscopy. The surfaces, were ion machined to depths from 0-5 microns. The finished surfaces were characterized to evaluate the effects of the ion machining process with respect to the previous processing methods and the pre-existing subsurface damage. The development of the control algorithms for figuring optical components has been completed. These algorithms have been validated with simulations and future experiments have been planned to verify the methods. This paper will present the results of the initial surface finish experiments and the control algorithms simulations.

Fawcett, Steven C.↗

Effects of roughness on the radar response to soil moisture of bare ground

The radar response to soil moisture content was experimentally determined for three different bare fields with considerably different surface roughnesses at eight frequencies in the 2 to 8 GHz band and for Horizontal transmit-Horizontal receive (HH) and Vertical transmit-Vertical receive (VV) polarizations. Analysis of the data indicated that the effect of roughness on the radar backscattering coefficient can be minimized by proper choice of the radar parameters. If, in addition, sensitivity to soil moisture variations and system design constraints are considered, the following radar parameters for an operational soil moisture mapper are recommended: frequency= 4 GHz, angle of incidence range= 7 deg to 15 deg and either HH or VV polarization. The corresponding sensitivity is about 0.25 db/ 0.01 gram/cubic cm.

Batlivala, P. P.↗

Study of Taxiing Problems Associated with Runway Roughness

This paper briefly summarizes available statistical data on airplane taxi operations, examines the profiles and power spectra of four selected runways and taxiways covering a wide range of surface roughness, considers (on the basis of theoretical and experimental results) the loads resulting from taxiing on such runways over a range of speeds and, by synthesis of the aforementioned results, proposes new criteria for runway and taxiway smoothness which are applicable to new construction and may also be used as a guide for determining when repairs are necessary.

Milwitzky, Benjamin↗