Search NASA⌕ Search

SEARCH · Search NASA

Results for “Additive Manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Repurposing the θ (Al 2 Cu) phase to simultaneously increase the strength and ductility of an additively manufactured Al–Cu alloy

The Al–Cu–Mn–Zr (ACMZ) cast family of alloys offers unique properties and value propositions for higher strength, higher temperature lightweight components of future vehicles. Earlier research has demonstrated trade-offs in the selection of the alloy chemistry in which an increase in Cu content from 6 up to 9 wt% improves hot tear resistance but lowers ductility. However, a recent study has demonstrated that higher-Cu (9Cu) ACMZ fabricated with laser powder bed fusion additive manufacturing (AM) results in an increase in both ductility and strength when compared to as-aged microstructure of cast 9Cu alloys. The mechanisms of differing mechanical performance of the cast and AM ACMZ alloys are elucidated in the current paper through the utilization of in situ high energy x-ray diffraction (HEXRD) tensile testing wherein lattice strains of different phases are calculated and correlated to their stresses. The ACMZ alloys consisted of theta (θ) and theta prime (θ') phases (both Al 2 Cu in nominal composition) within an aluminum matrix. The larger micron-size θ phase which decorated the grain boundaries in 9Cu ACMZ cast alloys recorded small lattice strains, while the submicron, homogeneously distributed θ phase in the 9Cu ACMZ AM alloy recorded considerably higher lattice strains. The maximum stress reached in the θ phase for the cast 9Cu alloy was found to be ~280 MPa, which was lower than the AM 9Cu alloy which registered a maximum stress of ~1.4 GPa. These measurements indicate that delayed fracture of the finer intermetallic phases simultaneously improves the ductility and strength of AM 9Cu alloy relative to the cast 9Cu alloy, which exhibits early fracture of the larger intermetallic particles.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Controlling microstructure and B2 ordering kinetics in Fe–Al system through additive manufacturing

Multi-material fabrication between steel and aluminum is challenging because of the formation of several intermetallic phases. Embrittling B2 ordered intermetallics form in the steel rich side and are stable till about 60% of Al dilution in steel. In this work by using multi-length scale characterization coupled with integrated computational process and thermokinetic modeling, we show that the ordered B2 intermetallics in the steel rich side of the Fe–Al system forms via a nucleation and growth mechanism. The extent of B2 ordered intermetallics can be controlled by modifying the directed energy deposition-additive manufacturing (DED-AM) process parameters. Our findings lay the foundation for enabling fabrication of crack-free functionally graded compositions between the two alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Boundary Topology Optimization Approach for Lightweighting Electric Machines Inspired by Additive Manufacturing

Minimizing the mass in electric machines while maintaining superior performance has become a new requirement for the advancement of drivetrains used in wind energy and electric mobility. Topology optimization for light-weighting electric machines using traditional approaches typically explore a restricted design space allowed by standard parametrizable geometry and manufacturing, while advanced methods like cell-based density approaches suffer from a lack of robust manufacturability constraints during the optimization process. To overcome these drawbacks, we explore a grid-independent, boundary TO where the outer shape of the magnet is parameterized using Bezier curves. We conduct a design of experiments (DOE) to study the effect of different magnet shapes on machine performance by varying the control points on the Bezier curves. A machine-learning based surrogate model is constructed using the data from the DOE to quantify the relationship between the control points, air-gap torque and mass. The control points are then optimized to maximize the torque density. The approach is used for minimizing electrical steel mass in the IEA-15MW radial flux direct-drive wind turbine generator. The free-from boundary TO resulted in smooth and concise shapes that can be easily additively manufactured with upto 20-ton reduction in electrical steel mass.

additive manufacturing↗
NASA NTRSDate not supplied

High-Throughput Strategies that Encompass Experiments and Machine Learning to Predict the Mechanical Properties of Additive Manufactured Aerospace Alloys

Small Punch Test (SPT) uses a thin disk of material to predict mechanical properties. While SPT has existed for decades, it has been used largely as a qualitative evaluator of mechanical properties. Recent advances in computational modeling have enabled the extraction of uniaxial stress-strain response from the measured SPT load-displacement data. Due to small sample volumes and unidirectional testing, SPT is conducive to high-throughput automation and ideally suited to extract properties from high-cost materials. Aerospace alloys have been of recent interest to the Additive Manufacturing (AM) community due to AM’s unique ability to fabricate complex designs not possible, or extremely arduous, with conventional manufacturing. In this research, SPT, coupled with Materials Informatics and computational modeling, is used to develop relevant Process-Structure-Property relationships to decrease the cost and time of process optimization for AM aerospace alloys, namely Inconel 718, Inconel 625, and Niobium C103.

High-throughput Testing↗
DOE OSTI2020

High-throughput additive manufacturing and characterization of refractory high entropy alloys

Refractory High Entropy Alloys (RHEAs) and Refractory Complex Concentrated Alloys (RCCAs) are high-temperature structural alloys ideally suited for use in harsh environments. While these alloys have shown promising structural properties at high temperatures that exceed the practical limits of conventional alloys, such as Ni-based superalloys, exploration of the complex phase-space of these materials remains a significant challenge. We report on a high-throughput alloy processing and characterization methodology, leveraging laser-based metal additive manufacturing (AM) and mechanical testing techniques, to enable rapid exploration of RHEAs/RCCAs. We utilized in situ alloying and compositional grading, unique to AM processing, to rapidly-produce RHEAs/RCCAs using readily available and inexpensive commercial elemental powders. We demonstrate this approach with the MoNbTaW alloy system, as a model material known for having exceptionally high strength at elevated temperature when processed using conventional methods (e.g., casting). Microstructure analysis, chemical composition, and strain rate dependent hardness of AM-processed material are presented and discussed in the context of understanding the structure-properties relationships of RHEAs/RCCAs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Functional fiber-optic sensors embedded in stainless steel components using ultrasonic additive manufacturing for distributed temperature and strain measurements

The nuclear industry is progressing toward microreactors that can be factory assembled and deployed to remote regions for reliable, scalable power generation. However, the reduced power output requires enhanced monitoring capabilities to reduce staffing and eventually move toward autonomous control to improve the economics of microreactors. The ability to embed sensors such as fiber-optics, which can provide spatially distributed temperature and strain measurements, within microreactor components for real-time health monitoring would be particularly advantageous. Recent advances in ultrasonic additive manufacturing (UAM) have demonstrated the successful embedding of fiber-optics in soft materials such as Al and Cu by placing the sensors in machined cavities and ultrasonically welding over the top with thin foils. This article reports the first successful embedment of fiber-optic sensors and thermocouples within a common nuclear reactor material, SS304, via UAM. UAM parameters were first explored with simple plate geometries before moving to more complex geometries, such as pipes and other test articles for heat pipe–based microreactors. Select samples were sectioned for microscopy to evaluate the sensor/foil and foil/foil interfaces from samples fabricated by using 100% SS304 foils vs. foils plated with a Ni coating to improve UAM bonding. Furthermore, embedding metal-coated, low-bend loss fibers resulted in greatly reduced signal attenuation and adequate compressive residual strain in the embedded region to ensure successful strain coupling. Pipe specimen functional testing was performed by monitoring temperature and strain during transient and steady-state thermal testing.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Development of Computational Materials Workflows for Additively Manufactured Metallic Materials to Enable Accelerated Prediction of Fatigue Performance

The maturation of computational materials approaches for fatigue performance prediction in a qualification and certification process is stifled by the ability to validate complex, microstructure-based simulations. Such a validation strategy bears immediate challenges including generating accurate virtual microstructures, efficiently solving physics-based mechanical simulations over relevant spatial and temporal scales, and acquiring high-fidelity calibration and validation data at the appropriate length scale. This presentation will overview these common challenges and present a case study to demonstrate a computational materials workflow for additively manufactured metallic materials. In this study, process-specific defects are characterized using segmented X-Ray micro-computed tomography measurements and overlaid on virtual microstructures. Accelerated crystal plasticity-based fatigue simulations are performed to demonstrate cyclic evolution and localization of mechanical fields in the vicinity of defects in response to their precise spatial configuration. An example of how this computational materials workflow may support next-generation qualification is discussed.

computational materials↗
DOE OSTI2022

Novel Tube Design for Superheater Heat Exchanger Enabled Via Additive Manufacturing

Superheater tubes are critical boiler components that operate at relatively higher temperatures and pressure. Amongst the primary concerns for these tubes is the deposition of ash particles on the tube surface, leading to the reduced thickness of the tube due to material corrosion, consequently causing early creep failure of the component. In this research, a novel tube design has been proposed which resembles a teardrop or ogive shape to reduce the drag and concurrently improve the creep life of the superheater tubes. To administer the practicality of novel tubes, metal additive manufacturing (AM), for instance, laser-powder bed fusion (L-PBF), has been proposed. These unconventional designs were assessed and compared with the baseline circular tube design for mechanical design requirements (hoop stress and creep life) and the particle and flue gas flow characteristics around the differently shaped tubes. A thermomechanical finite element (FE) analysis was performed for hoop stress calculations. This study also emphasizes on effect of circumferential thermal variation on hoop stress distribution in tubes. Therefore, a detailed two-dimensional (2D) thermal simulation has been performed to report the circumferential thermal variation on the tube. A computational fluid dynamics (CFD) analysis coupled with particle tracing was performed for gas flow visualization and particle tracing around the proposed shapes and baseline circular-shaped tube design. The Schlieren optic setup was built and leveraged for qualitative validation of the proposed design. The complete design methodology established in the paper shows teardrop-shaped tubes better in terms of drag and creep life in contrast to the circular-shaped tube.

42 ENGINEERING↗
DOE OSTI2022

A New Shape Optimization Approach for Lightweighting Electric Machines Inspired by Additive Manufacturing

Minimizing the mass in electric machines while maintaining superior performance is a new requirement for the advancement of drivetrains used in wind energy and electric mobility. Topology optimization (TO) for lightweighting electric machines using traditional approaches typically explores a restricted design space allowed by standard parametrizable geometry and manufacturing, while advanced methods, such as cell-based density approaches, suffer from a lack of robust manufacturability constraints during the optimization process. To overcome these drawbacks, we explore a grid-independent, boundary optimization where the outer shape of the magnet is parameterized using Bezier curves. We conduct a design of experiments (DOE) to study the effect of different magnet shapes on machine performance by varying the control points on the Bezier curves. A machine-learning-based surrogate model is constructed using the data from the DOE to quantify the relationship between the control points, air-gap torque, and mass. The control points are then optimized to maximize the torque density. The approach is used for minimizing electrical steel mass in the International Energy Agency (IEA) 15-MW radial flux direct-drive wind turbine generator. The new approach to shape optimization resulted in smooth and concise shapes that can be easily additively manufactured with up to a 20-ton reduction in electrical steel mass.

additive manufacturing↗
DOE OSTI2022

A New Shape Optimization Approach for Lightweighting Electric Machines Inspired by Additive Manufacturing: Preprint

Minimizing the mass in electric machines while maintaining superior performance is a new requirement for the advancement of drivetrains used in wind energy and electric mobility. Topology optimization (TO) for lightweighting electric machines using traditional approaches typically explores a restricted design space allowed by standard parametrizable geometry and manufacturing, while advanced methods, such as cell-based density approaches, suffer from a lack of robust manufacturability constraints during the optimization process. To overcome these drawbacks, we explore a grid-independent, boundary TO where the outer shape of the magnet is parameterized using Bezier curves. We conduct a design of experiments (DOE) to study the effect of different magnet shapes on machine performance by varying the control points on the Bezier curves. A machine-learning-based surrogate model is constructed using the data from the DOE to quantify the relationship between the control points, air-gap torque, and mass. The control points are then optimized to maximize the torque density. The approach is used for minimizing electrical steel mass in the International Energy Agency (IEA) 15-MW radial flux direct-drive wind turbine generator. The free-form boundary TO resulted in smooth and concise shapes that can be easily additively manufactured with up to a 20-ton reduction in electrical steel mass.

additive manufacturing↗
DOE OSTI2023

Design and additive manufacturing of optimized electrodes for energy storage applications

Supercapacitors exhibit fast charging/discharging ability and have attracted considerable attention within the automotive, aerospace, and telecommunication industries. Porous carbons, prized for their high electrical conductivity and high surface area, have been attractive candidates for supercapacitor electrodes. Moving to thick electrodes is one strategy to further increase energy density due to a higher volume fraction of active material. However, thick electrodes suffer from sluggish charged species transport, which is why thin electrodes are currently favored. In this work, we investigate the use of computational optimization and additive manufacturing to design and fabricate thick porous electrodes with improved performance. Electrode performance was maximized by designing their morphologies via topology optimization and printing by projection micro stereolithography (PμSL) using commercial resin (PR48). The PR48 resin was then pyrolyzed (PR48-P) to create the final conductive electrode. The optimized PR48-P electrodes exhibited 99% improvement in capacitance compared to control electrodes printed with cubic lattice morphologies. To further improve performance, we formulated a resin combining graphene oxide (GO) and trimethylolpropane triacrylate (TMPTA). Electrodes printed with 3 wt% GO in TMPTA exhibited improved capacitance retention after pyrolysis compared to the PR48-P electrodes. Finally, this work demonstrates the benefits of using topology optimization to design electrodes and material development to improve functional properties of 3D printable electrodes.

25 ENERGY STORAGE↗
DOE OSTI2024

Preliminary Assessment of Additively Manufactured Cooling Channel Performance for Helium-Cooled Blanket Concepts

Sufficient cooling of the blanket first wall remains a critical challenge for the design and deployment of fusion power plants. Helium has been targeted as a potential blanket coolant due to its inertness and low neutron interactivity, among other advantages. However, the low thermal mass of helium creates a need for heat transfer enhancements in coolant channels to provide adequate cooling to the blanket’s first wall. Toward this end, a series of ribbed flow channels of various rib cross sections and configurations has been produced via additive manufacturing (AM) to study the efficacy of AM for first wall heat transfer enhancement and the optimization of heat transfer geometries. Helium cooling performance is studied in AM test articles at 4 MPa operating pressure, Reynolds numbers up to 197 000, and outer surface heat fluxes up to 42 kW/m 2 in the recently commissioned helium flow loop experiment (HFLE). Preliminary results of this study are presented herein. Heat transfer performance of nominally smooth (i.e., featureless) AM channels is quantified via measured Nusselt numbers and friction factors and compared to off-the-shelf smooth pipe experiments. Results are compared to existing correlations and used to discuss the effects of the AM processes on thermal-hydraulic performance. It is seen that the inherent roughness of the AM channels leads to an increase in both heat transfer coefficient and pressure drop when compared to the conventional pipe. In conclusion, recommendations are made for future studies based on these findings and additional considerations for the deployment of AM blanket cooling components.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Characterization of Additively Manufacture GRCop-42 and GRCop-84

GRCop-42 (Cu-4 at.% Cr-2 at.% Nb) is a copper-based alloy optimized for high temperature, high thermal conductivity applications such as regenerative cooled rocket engine liners. For this application, it is important to minimize contamination such as trace elements and ceramic inclusions. NASA initiated a series of ten builds by eight companies to assess the repeatability of GRCop-42 between vendors and machines. Utilizing inductively coupled plasma – atomic emission spectroscopy (ICP-AES) and energy dispersive spectroscopy (EDS) techniques allowed for identification of contaminants and quantification of their chemistry. In addition, additive manufacturing (AM) creates a unique microstructure that is often highly textured in the build (Z) direction. Electron backscattered diffraction (EBSD) was used to begin quantifying the degree of crystallographic texture in the copper matrix grains. It was also used to identify the crystallographic form of Cr2Nb, the main strengthening phase, present in the samples. Results showed the presence of ceramic inclusions, highly textured grains, and both the low and high temperature phases of Cr2Nb being present.

copper↗
DOE OSTI2021

An integrated manifold learning approach for high-dimensional data feature extractions and its applications to online process monitoring of additive manufacturing

As an effective dimension reduction and feature extraction technique, manifold learning has been successfully applied to high-dimensional data analysis. With the rapid development of sensor technology, a large amount of high-dimensional data such as image streams can be easily available. Thus, a promising application of manifold learning is in the field of sensor signal analysis, particular for the applications of online process monitoring and control using high-dimensional data. The objective of this study is to develop a manifold learning-based feature extraction method for process monitoring of Additive Manufacturing (AM) using online sensor data. Due to the non-parametric nature of most existing manifold learning methods, their performance in terms of computational efficiency, as well as noise resistance has yet to be improved. To address this issue, this study proposes an integrated manifold learning approach termed multi-kernel metric learning embedded isometric feature mapping (MKML-ISOMAP) for dimension reduction and feature extraction of online high-dimensional sensor data such as images. Based on the extracted features with the utilization of supervised classification and regression methods, an online process monitoring methodology for AM is implemented to identify the actual process quality status. Finally, in the numerical simulation and real-world case studies, the proposed method demonstrates excellent performance in both prediction accuracy and computational efficiency.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ultrasonic Characterization of Material Properties in Metal Components Additively Manufactured by Powder Bed Fusion

We present the methodology for using pulsed-echo ultrasound to characterize the properties of additively manufactured (AM) metal components and their response to changes in the fabrication settings. We show how to accurately characterize anisotropy in these properties and when such characterization can be performed noninvasively. Our approach, when applied to 3D-printed stainless steel samples, reveals a significant heterogeneity between the surface and internal properties of the AM part and the anisotropy in material properties in the build and transverse directions.

Walton, Kenneth↗
DOE OSTI2023

Assessment of Process Modeling Tools for Determining Variability in Additively Manufactured Parts

The Advanced Materials and Manufacturing Technologies (AMMT) program aims to accelerate the development, qualification, demonstration, and deployment of advanced materials and manufacturing technologies to enable reliable and economical nuclear energy However, the unique aspects of additive manufacturing (AM) materials in terms of their processing history, microstructure, and properties, are a major barrier for qualification and certification of nuclear components. Much of this challenge may be attributed to component scale variations in microstructure and properties that are driven by local influences of process conditions and geometry on thermal history, melt pool dynamics, and corresponding microstructure evolution. Computational modeling tools may be helpful in this regard to aid in predicting and controlling this level of variability. The purpose of this report is to review the current state-of-the-art for process modeling with regards to metal AM. For this purpose, we consider specifically the case study of laser powder bed fusion (LPBF) processing of SS316, a family of alloys that are both commonly used in nuclear energy applications and suitable for AM processing. The report first introduces the necessary components of a process modeling workflow, followed by a review of the current status of each. At the end, application of these modeling tools to understanding variability in AM process given their current state are considered, and recommendations for future development are proposed

36 MATERIALS SCIENCE↗
NASA NTRS2017

Systems and Methods for Fabricating Objects Including Amorphous Metal Using Techniques Akin to Additive Manufacturing

Systems and methods in accordance with embodiments of the invention fabricate objects including amorphous metals using techniques akin to additive manufacturing. In one embodiment, a method of fabricating an object that includes an amorphous metal includes: applying a first layer of molten metallic alloy to a surface; cooling the first layer of molten metallic alloy such that it solidifies and thereby forms a first layer including amorphous metal; subsequently applying at least one layer of molten metallic alloy onto a layer including amorphous metal; cooling each subsequently applied layer of molten metallic alloy such that it solidifies and thereby forms a layer including amorphous metal prior to the application of any adjacent layer of molten metallic alloy; where the aggregate of the solidified layers including amorphous metal forms a desired shape in the object to be fabricated; and removing at least the first layer including amorphous metal from the surface.

Hofmann, Douglas↗
NASA NTRS2019

Fracture Control and Structural Certification Guidance for Additive Manufactured Spacecraft Structures

This paper offers a NASA perspective on guidance for fracture control and structural certification of "fracture critical" additive manufactured spacecraft structures. Results of a recent industry survey on the need for maturing NASA guidance for AM certification are presented for the first time. The survey results are placed in the context of a description of what NASA standards in this area already exist, where the gaps are, and what work to address the gaps is underway.

McElroy, Mark↗