Search NASA⌕ Search

SEARCH · Search NASA

Results for “Advanced visualization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

Characterization of Build Parameters and Microstructure in Low Heat Input WAAM of Ni-Based Superalloy Haynes 282

Ni-based superalloy Haynes® 282® is being targeted for various applications in advanced power generation systems for its superior fabricability, weldability, and excellent high temperature creep and corrosion performance. This process optimization study aims to use a low heat-input, high deposition rate, controlled Gas Metal Arc Welding (GMAW) process, Cold Metal Transfer (CMT) by Fronius, attempting to achieve fully dense fabrication and possibly avoid the need for HIP. Twenty-one multilayer blocks (~25x100x40 mm3) were deposited to explore a large set of build parameters variations that focused on varying the travel speed from 14 to 42 inches per minute (ipm) and wire feed speed from 150 to 450 ipm. A strong correlation has been observed between arc energy – controlled primarily by travel and wire feed speed. Initial visual inspection, internal microstructural examination, and computed tomography (CT) have been used to determine the effects of built parameters on evolution of internal porosity and defects. Scanning electron microscopy techniques enabled structural and compositional imaging of heterogeneity and changes in microstructural properties.

additive manufacturing↗

Characterization of Build Parameters and Microstructure in Low Heat Input WAAM of Ni-Based Superalloy Haynes 282

Ni-based superalloy Haynes® 282® is being targeted for various applications in advanced power generation systems for its superior fabricability, weldability, and excellent high temperature creep and corrosion performance. This process optimization study aims to use a low heat-input, high deposition rate, controlled Gas Metal Arc Welding (GMAW) process, Cold Metal Transfer (CMT) by Fronius, attempting to achieve fully dense fabrication and possibly avoid the need for HIP. Twenty-one multilayer blocks (~25x100x40 mm3) were deposited to explore a large set of build parameters variations that focused on varying the travel speed from 14 to 42 inches per minute (ipm) and wire feed speed from 150 to 450 ipm. A strong correlation has been observed between arc energy – controlled primarily by travel and wire feed speed. Initial visual inspection, internal microstructural examination, and computed tomography (CT) have been used to determine the effects of built parameters on evolution of internal porosity and defects. Scanning electron microscopy techniques enabled structural and compositional imaging of heterogeneity and changes in microstructural properties.

additive manufacturing↗

Geometry definition and grid generation for a complete fighter aircraft

Recent advances in computing power and numerical solution procedures have enabled computational fluid dynamicists to attempt increasingly difficult problems. In particular, efforts are focusing on computations of complex three-dimensional flow fields about realistic aerodynamic bodies. To perform such computations, a very accurate and detailed description of the surface geometry must be provided, and a three-dimensional grid must be generated in the space around the body. The geometry must be supplied in a format compatible with the grid generation requirements, and must be verified to be free of inconsistencies. This paper presents a procedure for performing the geometry definition of a fighter aircraft that makes use of a commercial computer-aided design/computer-aided manufacturing system. Furthermore, visual representations of the geometry are generated using a computer graphics system for verification of the body definition. Finally, the three-dimensional grids for fighter-like aircraft are generated by means of an efficient new parabolic grid generation method. This method exhibits good control of grid quality.

Edwards, T. A.↗

Advanced Manufacturing Techniques Demonstrated for Fabricating Developmental Hardware

NASA Glenn Research Center's Engineering Development Division has been working in support of innovative gas turbine engine systems under development by Glenn's Combustion Branch. These one-of-a-kind components require operation under extreme conditions. High-temperature ceramics were chosen for fabrication was because of the hostile operating environment. During the designing process, it became apparent that traditional machining techniques would not be adequate to produce the small, intricate features for the conceptual design, which was to be produced by stacking over a dozen thin layers with many small features that would then be aligned and bonded together into a one-piece unit. Instead of using traditional machining, we produced computer models in Pro/ENGINEER (Parametric Technology Corporation (PTC), Needham, MA) to the specifications of the research engineer. The computer models were exported in stereolithography standard (STL) format and used to produce full-size rapid prototype polymer models. These semi-opaque plastic models were used for visualization and design verification. The computer models also were exported in International Graphics Exchange Specification (IGES) format and sent to Glenn's Thermal/Fluids Design & Analysis Branch and Applied Structural Mechanics Branch for profiling heat transfer and mechanical strength analysis.

Redding, Chip↗

An Open-Access Nuclear Knowledge and Innovation Toolkit to Make Use of Nuclear World and Increase Collaboration

Nuclear engineering began as an urgent weapons development program in the early 1940s, involving work in enrichment, reactor design, shielding design, and isotope production. This work led to investigations of peaceful uses of nuclear technology, including nuclear power production and applications of radiation. Such peaceful technologies, often derived from experience gained through the weapons program, often maintained some level or attitude of secrecy. As the field continued to develop, that secrecy led to different specializations developing with different sets of terminology and methods of computation. For example, radiation safety used buildup and shielding factors while reactor designers use diffusivity and cross sections. Impressive amounts of work went into theory and application development in each sub-field over the next few decades, with much of the work left without adequate documentation or with important documentation made only within the organization. This situation has led to a loss of knowledge and experience, a lack of collaboration across nuclear sub-fields, and immense amounts of time and effort spent on redundant work. This paper proposes an open-access system that combines preserving and passing on the knowledge in all nuclear sub-fields with tools to make that knowledge useful, referred to as the Nuclear Knowledge and Innovation Toolkit (NuKIT). Knowledge would be captured in user-entered and expert-verified databases of reactors, applications of radiation, isotope production methods, and other pertinent nuclear information complete with technical information and tags that can be used to organize and investigate the data. Tools include community tools like forums and the ability to create collaborative projects; visualization and presentation tools; and an online programming system that allows code sharing, collaborative editing, database manipulation, and integration with all other tools. Finally, NuKIT is envisioned to include commercialization tools to allow freelance work and to compensate data entry/moderation work to help encourage participation. Eventually, integration with industry-standard tools like MCNP, SCALE, etc. is expected. This paper will present some proposed work in the context of its use for isotopes and radiation application, as well as possible work to be done in the context of the Combined Materials Experimental Toolkit (CoMET) being developed by the Nuclear Science User Facilities (NSUF) program. It should be noted that any work done towards this system, by any group, will advance the full system. It should also be noted that similar work previously done can be integrated into NuKIT.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Advancing \textit{otsdaq}: Enhancements for Usability, Accuracy, and Robustness

High-energy physics (HEP) experiments require data acquisition (DAQ) systems that can orchestrate complex detector operations, high data throughput, and responsive, real-time feedback to operators. Traditional DAQ stacks, which are often bespoke, command-line driven and highly specific, impose large learning curves on users. The Off-The-Shelf Data Acquisition (\textit{otsdaq}) framework was created to address these issues by offering a highly customizable and scalable browser-based ’desktop’ environment, in which experiment-specific control and monitoring applications can be easily deployed and integrated. Although the initial development of the \textit{otsdaq} software was aimed at the Fermilab Test Beam Facility, \textit{otsdaq} is now being leveraged for broader deployment, including the upcoming Mu2e experiment, where real-time monitoring of field-programmable gate array (FPGA)-based Data Transfer Controllers (DTCs), Clock and Fanout (CFO) boards, and several other subsystems are critical. We contribute a set of targeted improvements to \textit{otsdaq}: bitmap visualization functionality for configured data, improved and corrected delta-based DTC throughput metrics, version control (VC)-backed source navigation for console messages, custom navigation hooks to eliminate disruptive user interface glitches, and copy-to-clipboard support for macro execution history. These changes improve usability, reduce debugging time, and increase accuracy in performance data as Mu2e moves toward commissioning.

Mohammed, A. [Unlisted, US]↗

Visualization of High Latitude Ion Upflow in Support of the Image Mission

The study of the magnetosphere is a 400 year old science that began with the publication by Gilbert, in 1600, of his hypotheses that the Earth was a giant magnet. Since then we have learned many things about the magnetosphere, particularly in the last 40 years of the space age, but we still have many unanswered questions. In spite of the many thousands of observations of this system we still lack a global understanding of how it works. This is due to its large size and tenuous nature that mean that any measurement made of the fields or particles involved only give one a knowledge of the local conditions at a given time. To gain a global perspective through such observations would require the simultaneous operation of thousands of satellites spread throughout the magnetospheric system in addition to observations made on the ground. Such a program would be impractical at least from financial considerations. What is needed for the advancement of magnetospheric physics is to develop the same capabilities that astrophysicists, solar physicists and meteorologists have been using for years --- the ability to stand back from the object under study and see it in its entirety. The challenge for doing this for the magnetosphere is that the particle densities are very low and the material is, for the most part, not luminous. In the last 25 years several ideas have been proposed that would allow at least the imaging of certain portions of the magnetosphere. These include imaging of the plasmasphere through the resonant scattering of solar 304 A from He+ ions, imaging of various hot plasma populations (i.e. the ring current, plasmasheet, upflowing ionospheric ions, etc.) from the neutral atoms that result when ions of these populations charge exchange with the hydrogen geocorona, and imaging the aurora at various wavelengths in the far ultraviolet. In addition, a novel technique for probing various boundaries in the magnetosphere by bouncing low frequency radio waves off of them has been extensively studied. Such a technique is analogous to the way the under water world can be probed with sonar. About five years ago NASA convened a science working group to study the possibility of flying a magnetospheric imaging mission. This resulted in a number of proposals for such a mission, one of which was selected to be the first MIDEX mission, to be launched in early 2000. The mission is called IMAGE (Imager for Magnetopause to Aurora Global Exploration) and its P.I. is J. Burch at SwRI. The IMAGE spacecraft will carry imagers to view the plasmasphere, aurora, ring current, inner plasmasheet, and upflowing ionospheric ions as well as a radio sounder to probe the location, shape and dynamics of the magnetopause, plasmapause, etc. Between its selection last April and the non advocacy mission review, which takes place next spring, the IMAGE teams needs to further refine the design of the mission and its instruments. The theory and modeling (T&M) subgroup of this team has the task of demonstrating what kind of images the instruments on IMAGE will see as well as showing that useful scientific information can be extracted from such images. As a central element to the efforts of the T&M subgroup we have decided to simulate and create synthetic images for the magnetic cloud event of October, 1995. In this event a large cloud, with high plasma densities and strong magnetic fields, ejected from the sun collided with the earth's magnetosphere triggering a three day period of intense magnetic storms and substorms. This event was observed from a number of different spacecraft and on the ground so we have a good data set to work with. In our work we will place the IMAGE spacecraft in the magnetosphere on its proposed orbit, with its proposed instruments, to see what it would see had it been there. Existing models of the plasmasphere, ring current and magnetopause will be run for this event to give the structures for the imaging instruments. There are several models which are lacking and which need to be developed. These include a model for the cusp, the inner plasmasheet and the upflowing ions. My task this summer was to develop the upflowing ion model and use it to create synthetic images.

Wilson, Gordon R.↗

Technology Enabling Zero-EPZ Micro Modular Reactors: Fabrication of Zirconium Hydride with Controlled Hydrogen Loading

This report completes Milestone M2.2.2 - ZrH pellet fabricated with controlled hydride loading: ZrH1.5±0.1 single phase pellets fabricated with controlled and thermally stable hydride loading. Hydrogen content to be quantified and single-phase confirmed by X-ray diffraction. In this milestone, we report the successful fabrication of delta-phase zirconium hydride pellets using the ORNL bulk metal hydriding system. The successful deployment of zirconium hydride moderator in advanced reactors requires development of a consistent and affordable production pathway along with implementation of a hydrogen retention solution throughout the reactor life. Fabrication of delta-phase zirconium hydride is challenging since the absorption of a large amount of hydrogen into alpha-zirconium induces significant volume expansion and the present hydrogen concentration gradient results in cracking. A fully programmable hydriding system with continuous hydrogen partial pressure and flow control to facilitate processing of massive metal hydride has been developed at ORNL. In this report, the working principle of the hydriding system will be introduced. Characterization of the produced zirconium hydride includes X-ray powder diffraction to identify the present phases and X-ray Computed Tomography to visualize the internal microstructure (including cracks). The results indicate that single delta-phase zirconium hydride pellets with various sizes have been successfully produced.

36 MATERIALS SCIENCE↗

Multi-Disciplinary Analysis for Future Launch Systems Using NASA's Advanced Engineering Environment (AEE)

A new engineering environment constructed for the purposes of analyzing and designing Reusable Launch Vehicles (RLVs) is presented. The new environment has been developed to allow NASA to perform independent analysis and design of emerging RLV architectures and technologies. The new Advanced Engineering Environment (AEE) is both collaborative and distributed. It facilitates integration of the analyses by both vehicle performance disciplines and life-cycle disciplines. Current performance disciplines supported include: weights and sizing, aerodynamics, trajectories, propulsion, structural loads, and CAD-based geometries. Current life-cycle disciplines supported include: DDT&E cost, production costs, operations costs, flight rates, safety and reliability, and system economics. Involving six NASA centers (ARC, LaRC, MSFC, KSC, GRC and JSC), AEE has been tailored to serve as a web-accessed agency-wide source for all of NASA's future launch vehicle systems engineering functions. Thus, it is configured to facilitate (a) data management, (b) automated tool/process integration and execution, and (c) data visualization and presentation. The core components of the integrated framework are a customized PTC Windchill product data management server, a set of RLV analysis and design tools integrated using Phoenix Integration's Model Center, and an XML-based data capture and transfer protocol. The AEE system has seen production use during the Initial Architecture and Technology Review for the NASA 2nd Generation RLV program, and it continues to undergo development and enhancements in support of its current main customer, the NASA Next Generation Launch Technology (NGLT) program.

Monell, D.↗

New Flight Rules to Enable the Era of Aerial Mobility in the National Airspace System

In the 21st Century, new aviation markets, vehicle types, and technologies are fast emerging, inspiring new operational concepts for the National Airspace System such as Unmanned Aircraft Systems Traffic Management and Urban Air Mobility. These novel operations envision a dramatic increase in aerial mobility, or the ability to navigate freely through the airspace with unprecedented access and operational flexibility. Implementing these concepts presents a major challenge to the existing operational modes of Visual Flight Rules (VFR) and Instrument Flight Rules (IFR), developed under the limitations of early 20th Century technology and procedures to ensure safe navigation and separation from traffic. To meet this challenge and to support the needs of operators in the 21st Century and beyond, this paper proposes that VFR and IFR be augmented by new flight rules – Digital Flight Rules (DFR) – that leverage modern and emerging technologies and are not bound by restrictions borne of the state of technology 75-100 years ago. The objective of DFR is to provide safe and unfettered access to the airspace to all participating vehicle operators under all visibility conditions without incurring the limitations in operational flexibility inherent to IFR and even VFR. Advancements in communications, navigation, surveillance, aircraft connectivity, information access, automation technology, and supporting ground infrastructure provide the opportunity for the vehicle operator to engage at an unprecedented level in managing their flights regardless of flight visibility. Under DFR, these advancements enable the vehicle operator to assume full responsibility for traffic separation and therefore full trajectory management authority in all visibility conditions and airspace regions. The changes in roles and responsibilities are expected to enable greater airspace access and operational flexibility than afforded by IFR and VFR, thus enabling the emergence of new operations and a new era of advanced aerial mobility.

Mobility↗

Digital Flight: Enabling the Era of Scalable Mobility in the National Airspace System

In the 21st Century, new aviation markets, vehicle types, and technologies are fast emerging, inspiring new operational concepts for the National Airspace System such as Unmanned Aircraft Systems Traffic Management and Urban Air Mobility. These novel operations envision a dramatic increase in aerial mobility, or the ability to navigate freely through the airspace with unprecedented access and operational flexibility. Implementing these concepts presents a major challenge to the existing operational modes of Visual Flight Rules (VFR) and Instrument Flight Rules (IFR), developed under the limitations of early 20th Century technology and procedures to ensure safe navigation and separation from traffic. To meet this challenge and to support the needs of operators in the 21st Century and beyond, this paper proposes that VFR and IFR be augmented by new flight rules – Digital Flight Rules (DFR) – that leverage modern and emerging technologies and are not bound by restrictions borne of the state of technology 75-100 years ago. The objective of DFR is to provide safe and unfettered access to the airspace to all participating vehicle operators under all visibility conditions without incurring the limitations in operational flexibility inherent to IFR and even VFR. Advancements in communications, navigation, surveillance, aircraft connectivity, information access, automation technology, and supporting ground infrastructure provide the opportunity for the vehicle operator to engage at an unprecedented level in managing their flights regardless of flight visibility. Under DFR, these advancements enable the vehicle operator to assume full responsibility for traffic separation and therefore full trajectory management authority in all visibility conditions and airspace regions. The changes in roles and responsibilities are expected to enable greater airspace access and operational flexibility than afforded by IFR and VFR, thus enabling the emergence of new operations and a new era of advanced aerial mobility.

Mobility↗

Overview of an Exploratory, Real-Time, Multi-Pilot Simulation Study of Early eVTOL Operations at Non-Towered Vertiports

This paper provides a report out on an exploratory, multi-aircraft/multi-pilot, real-time simulation study conducted by NASA of early commercial powered-lift, Urban Air Mobility (UAM) operations at a non-towered vertiport. As used in this paper, vertiport refers to the primary ground and airspace elements facilitating the takeoff and landing of electric vertical takeoff and landing (eVTOL) aircraft with central emphasis on a vertipad, i.e. the physical touch-down and lift-off area and surrounding approach , departure, local pattern procedures. The study, known as the Piloted UML-2 ConOps Study (PUCS), had two high-level goals. The first goal was providing preliminary insights and observations relevant to the piloting and flight operations of early, commercial UAM operations aligned with the initial stage of the FAA’s Advanced Air Mobility (AAM) Implementation Plan and the second level NASA’s UAM Maturity Level (UML) scale. The second goal was evaluating a novel, medium-fidelity, extensible, many-pilot, real-time simulation capability known as the UAM Flyers developed by NASA. The Flyers are intended to allow rapid development, screening, evaluation, and demonstrations of potential Concepts of Operation (ConOps) for UAM flight operations and airspace management in a modular and low-cost, real-time, human-in-the-loop rapid simulation prototyping environment. For this study, ten Flyer cockpits were configured to evaluate flight operations through a non-towered vertiport with pilot interfaces and displays (external and in-cockpit) appropriate for operations under visual flight rules (VFR) and employing flight and communication procedures representative of current operations at non-towered airports. The presented results include an achieved operational tempo; durations of individual flight tasks for approaches and departures; off-nominal events and triggers; and pilot comments regarding potential procedural and technology improvements.

Urban Air Mobility↗

Overview of an Exploratory, Multi-Pilot Simulation Study of Early eVTOL Operations at Non-Towered Vertiports

This paper provides a report out on an exploratory, multi-aircraft/multi-pilot, real-time simulation study conducted by NASA of early commercial powered-lift, Urban Air Mobility (UAM) operations at a non-towered vertiport. As used in this paper, vertiport refers to the primary ground and airspace elements facilitating the takeoff and landing of electric vertical takeoff and landing (eVTOL) aircraft with central emphasis on a vertipad, i.e. the physical touch-down and lift-off area and surrounding approach , departure, local pattern procedures. The study, known as the Piloted UML-2 ConOps Study (PUCS), had two high-level goals. The first goal was providing preliminary insights and observations relevant to the piloting and flight operations of early, commercial UAM operations aligned with the initial stage of the FAA’s Advanced Air Mobility (AAM) Implementation Plan and the second level NASA’s UAM Maturity Level (UML) scale. The second goal was evaluating a novel, medium-fidelity, extensible, many-pilot, real-time simulation capability known as the UAM Flyers developed by NASA. The Flyers are intended to allow rapid development, screening, evaluation, and demonstrations of potential Concepts of Operation (ConOps) for UAM flight operations and airspace management in a modular and low-cost, real-time, human-in-the-loop rapid simulation prototyping environment. For this study, ten Flyer cockpits were configured to evaluate flight operations through a non-towered vertiport with pilot interfaces and displays (external and in-cockpit) appropriate for operations under visual flight rules (VFR) and employing flight and communication procedures representative of current operations at non-towered airports. The presented results include an achieved operational tempo; durations of individual flight tasks for approaches and departures; off-nominal events and triggers; and pilot comments regarding potential procedural and technology improvements.

Urban Air Mobility↗

Experimental research of graphite behavior under the air ingress accident condition of High Temperature Gas-cooled Reactor - 18752

As the major component of both cladding and grid spacer materials of High Temperature Gas-cooled Reactor (HTGR), graphite plays an important role on heat removal during the severe accident sequence. However, its heat transfer behavior in high temperature condition may be affected by the oxidation of graphite when the air or steam ingresses in an accident. In this research, an experiment was conducted to analyze the graphite heat transfer behavior in high temperature oxidable environment. An assembly including two graphite rings was used as the test section. It was heated up by a tungsten wire, which is installed inside the inner graphite ring and be joule heated. Temperature was measured by several K-type thermos-couples in certain positions. Argon gas was injected in advance to avoid the unwanted oxidation by the oxygen in the air. Air was injected into the gap between two graphite rings once the temperature of the inner ring reached target point to create the oxidable environment. Based on the results, a rapid increase of inner graphite ring's temperature can be observed after starting injected the air, and a rapid decrease after stopped the injection. It might due to the chemical reaction heat during the graphite surface oxidation. By comparing the steady state before and after air injection, the inner specimen s temperature is a little bit lower after the oxidation, which suggests that its ability of radiation heat transfer might be enhanced a little bit by oxidation. By visualized the test section, coarser surface at the inner graphite ring can be observed after the oxidation. In addition, about 8.9% mass loss of the oxidized graphite can also be found from the posttest examination. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

SCALE Code System

The SCALE Code System is a widely-used modeling and simulation suite for nuclear safety analysis and design that is developed, maintained, tested, and managed by the Reactor and Nuclear Systems Division (RNSD) of Oak Ridge National Laboratory (ORNL). SCALE provides a comprehensive, verified and validated, user-friendly tool set for criticality safety, reactor and lattice physics, radiation shielding, spent fuel and radioactive source term characterization, and sensitivity and uncertainty analysis. Since 1980, regulators, licensees, and research institutions around the world have used SCALE for safety analysis and design. SCALE provides an integrated framework with dozens of computational modules including three deterministic and three Monte Carlo radiation transport solvers that are selected based on the desired solution strategy. SCALE includes current nuclear data libraries and problem-dependent processing tools for continuous-energy (CE) and multigroup (MG) neutronics and coupled neutron-gamma calculations, as well as activation, depletion, and decay calculations. SCALE includes unique capabilities for automated variance reduction for shielding calculations, as well as sensitivity and uncertainty analysis. SCALE’s graphical user interfaces assist with accurate system modeling, visualization of nuclear data, and convenient access to desired results.SCALE 6.2 provides many new capabilities and significant improvements of existing features.New capabilities include:• ENDF/B-VII.1 nuclear data libraries CE and MG with enhanced group structures,• Neutron covariance data based on ENDF/B-VII.1 and supplemented with ORNL data,• Covariance data for fission product yields and decay constants,• Stochastic uncertainty and correlation quantification for any SCALE sequence with Sampler,• Parallel calculations with KENO,• Problem-dependent temperature corrections for CE calculations,• CE shielding and criticality accident alarm system analysis with MAVRIC,• CE depletion with TRITON (T5-DEPL/T6-DEPL),• CE sensitivity/uncertainty analysis with TSUNAMI-3D,• Simplified and efficient LWR lattice physics with Polaris,• Large scale detailed spent fuel characterization with ORIGAMI and ORIGAMI Automator,• Advanced fission source convergence acceleration capabilities with Sourcerer,• Nuclear data library generation with AMPX, and• Integrated user interface with Fulcrum.Enhanced capabilities include:• Accurate and efficient CE Monte Carlo methods for eigenvalue and fixed source calculations,• Improved MG resonance self-shielding methodologies and data,• Resonance self-shielding with modernized and efficient XSProc integrated into most sequences,• Accelerated calculations with TRITON/NEWT (generally 4x faster than SCALE 6.1),• Spent fuel characterization with 1470 new reactor-specific libraries for ORIGEN,• Modernization of ORIGEN (Chebyshev Rational Approximation Method [CRAM] solver, API for high-performance depletion, new keyword input format)• Extension of the maximum mixture number to values well beyond the previous limit of 2147 to ~2 billion,• Nuclear data formats enabling the use of more than 999 energy groups,• Updated standard composition library to provide more accurate use of natural abundances, andvi• Numerous other enhancements for improved usability and stability.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

The Cambrian Evolutionary Explosion: Novel Evidence from Fossils Studied by X-ray Tomography

The Cambrian explosion (from 542 million years to 488 million years ago) is one of the greatest mysteries in evolutionary biology. It wasn't until this period that complex organisms became common and diverse. the magnitude of the event can be understood based on the contrast between the biota and the degree of diversity of the fossils from both sides. great advances have been made in Cambrian palaeontology over the past century, especially the discovery of the well-preserved soft-bodied fauna from the Middle Cambrian Burgess Shale and the Lower Cambrian Maotianshan Shale deposits. The Cambrian side of the "Cambrian explosion" is richly illustrated and contrasts greatly with the Precambrian side. The study of these extraordinarily preserved fossil biota is extremely difficult. A major challenge is 3-D reconstruction and determining the patter of the cell organization in Weng'an embryos and their buried structures in Maotianshan Shale fossils. This talk will show that two recent technological approaches, propagation phase contrast synchrotron x-ray microtomography and microtomography, provide unique analytical tools that permit the nondestructive computational examination and visualization of the internal and buried characters in virtual sections in any plane, and virtual 3-D depictions of internal structures.

59 BASIC BIOLOGICAL SCIENCES↗

MATE (Materials for Advanced Turbine Engines) Program, Project 3. Volume 2: Design, fabrication and evaluation of an oxide dispersion strengthened sheet alloy combustor liner

The suitability of wrought oxide dispersion strengthened (ODS) superalloy sheet for gas turbine engine combustor applications was evaluated. Two yttria (Y2O3) dispersion strengthened alloys were evaluated; Incoloy MA956 and Haynes Development Alloy (HDA) 8077 (NiCrAl base). Preliminary tests showed both alloys to be potentially viable combustor materials, with neither alloy exhibiting a significant advantage over the other. MA956 was selected as the final alloy based on manufacturing reproducibility for evaluation as a burner liner. A hybrid PW2037 inner burner liner containing MA956 and Hastelloy X components and using a louvered configuration was designed and constructed. The louvered configuration was chosen because of field experience and compatibility with the bill of material PW2037 design. The simulated flight cycle for the ground based engine tests consisted of 4.5 min idle, 1.5 min takeoff and intermediate conditions in a PW2037 engine with average uncorrected combustor exit temperature of 1527 C. Post test evaluation consisting of visual observations and fluorescent penetrant inspections was conducted after 500 cycles of testing. No loss of integrity in the burner liner was shown.

Bose, S.↗

NASA advanced design program. Design and analysis of a radio-controlled flying wing aircraft

The main challenge of this project was to design an aircraft that will achieve stability while flying without a horizontal tail. The project focused on both the design, analysis and construction of a remotely piloted, elliptical shaped flying wing. The design team was composed of four sub-groups each of which dealt with the different aspects of the design, namely aerodynamics, stability and control, propulsion, and structures. Each member of the team initially researched the background information pertaining to specific facets of the project. Since previous work on this topic was limited, most of the focus of the project was directed towards developing an understanding of the natural instability of the aircraft. Once the design team entered the conceptual stage of the project, a series of compromises had to be made to satisfy the unique requirements of each sub-group. As a result of the numerous calculations and iterations necessary, computers were utilized extensively. In order to visualize the design and layout of the wing, engines and control surfaces, a solid modeling package was used to evaluate optimum design placements. When the design was finalized, construction began with the help of all the members of the project team. The nature of the carbon composite construction process demanded long hours of manual labor. The assembly of the engine systems also required precision hand work. The final product of this project is the Elang, a one-of-a-kind remotely piloted aircraft of composite construction powered by two ducted fan engines.

Source record↗