Search NASA⌕ Search

SEARCH · Search NASA

Results for “Component effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

Ares I Reaction Control System Propellant Feedline Decontamination Modeling

The objective of the work presented here is to quantify the effects of purge gas temperature, pressure, and mass flow rate on Hydrazine (Hz) decontamination rates of the Ares I Roll Control System and Reaction Control System. A survey of experts in this field revealed the absence of any decontamination rate prediction models. Three basic decontamination methods were identified for analysis and modeling. These include low pressure eduction, high flow rate purge, and pulse purge. For each method, an approach to predict the Hz mass transfer rate, as a function of system pressure, temperature, and purge gas mass flow rate, is developed based on the applicable physics. The models show that low pressure eduction is two orders of magnitude more effective than the high velocity purge, which in turn is two orders of magnitude more effective than the pure diffusion component of pulse purging of deadheads. Eduction subjects the system to low pressure conditions that promote the extraction of Hz vapors. At 120 F, Hz is saturated at approximately 1 psia. At lower pressures and 120 F, Hz will boil, which is an extremely efficient means to remove liquid Hz. The Hz boiling rate is predicted by equating the rate at which energy is added to the saturated liquid Hz through heaters at the tube outer wall with the energy removed from the liquid through evaporation. Boil-off fluxes were predicted by iterating through the range of local pressures with limits set by the minimum allowed pressure of 0.2 psia and maximum allowed wall temperature of 120 F established by the heaters, which gives a saturation pressure of approximately 1.0 psia. Figure 1 shows the resulting boil-off fluxes as a function of local eduction pressure. As depicted in figure 1, the flux is a strong inverse function of eduction pressure, and that minimizing the eduction pressure maximizes the boil-off flux. Also, higher outer wall temperatures lead to higher boil-off fluxes and allow for boil-off over a greater range of eduction pressures.

Pasch, James J.↗

Photometer Performance Assessment in Kepler Science Data Processing

This paper describes the algorithms of the Photometer Performance Assessment (PPA) software component in the science data processing pipeline of the Kepler mission. The PPA performs two tasks: One is to analyze the health and performance of the Kepler photometer based on the long cadence science data down-linked via Ka band approximately every 30 days. The second is to determine the attitude of the Kepler spacecraft with high precision at each long cadence. The PPA component is demonstrated to work effectively with the Kepler flight data.

Li, Jie↗

Status of Solar Sail Technology Within NASA

In the early 2000s, NASA made substantial progress in the development of solar sail propulsion systems for use in robotic science and exploration of the solar system. Two different 20-m solar sail systems were produced and they successfully completed functional vacuum testing in NASA Glenn Research Center's (GRC's) Space Power Facility at Plum Brook Station, Ohio. The sails were designed and developed by ATK Space Systems and L Garde, respectively. The sail systems consist of a central structure with four deployable booms that support the sails. These sail designs are robust enough for deployment in a one-atmosphere, one-gravity environment and were scalable to much larger solar sails perhaps as large as 150 m on a side. Computation modeling and analytical simulations were also performed to assess the scalability of the technology to the large sizes required to implement the first generation of missions using solar sails. Life and space environmental effects testing of sail and component materials were also conducted. NASA terminated funding for solar sails and other advanced space propulsion technologies shortly after these ground demonstrations were completed. In order to capitalize on the $30M investment made in solar sail technology to that point, NASA Marshall Space Flight Center (MSFC) funded the NanoSail-D, a subscale solar sail system designed for possible small spacecraft applications. The NanoSail-D mission flew on board the ill-fated Falcon-1 Rocket launched August 2, 2008, and due to the failure of that rocket, never achieved orbit. The NanoSail-D flight spare will be flown in the Fall of 2010. This paper will summarize NASA's investment in solar sail technology to-date and discuss future opportunities

Johnson, Les↗

Lifetime Assessment of the NEXT Ion Thruster

Ion thrusters are low thrust, high specific impulse devices with required operational lifetimes on the order of 10,000 to 100,000 hr. The NEXT ion thruster is the latest generation of ion thrusters under development. The NEXT ion thruster currently has a qualification level propellant throughput requirement of 450 kg of xenon, which corresponds to roughly 22,000 hr of operation at the highest throttling point. Currently, a NEXT engineering model ion thruster with prototype model ion optics is undergoing a long duration test to determine wear characteristics and establish propellant throughput capability. The NEXT thruster includes many improvements over previous generations of ion thrusters, but two of its component improvements have a larger effect on thruster lifetime. These include the ion optics with tighter tolerances, a masked region and better gap control, and the discharge cathode keeper material change to graphite. Data from the NEXT 2000 hr wear test, the NEXT long duration test, and further analysis is used to determine the expected lifetime of the NEXT ion thruster. This paper will review the predictions for all of the anticipated failure mechanisms. The mechanisms will include wear of the ion optics and cathode s orifice plate and keeper from the plasma, depletion of low work function material in each cathode s insert, and spalling of material in the discharge chamber leading to arcing. Based on the analysis of the NEXT ion thruster, the first failure mode for operation above a specific impulse of 2000 sec is expected to be the structural failure of the ion optics at 750 kg of propellant throughput, 1.7 times the qualification requirement. An assessment based on mission analyses for operation below a specific impulse of 2000 sec indicates that the NEXT thruster is capable of double the propellant throughput required by these missions.

VanNoord, Jonathan L.↗

Improved Measurement of Coherence in Presence of Instrument Noise

A method for correcting measured coherence spectra for the effect of incoherent instrument noise has been developed and demonstrated. Coherence measurements are widely used in engineering and science to determine the extent to which two signals are alike. The signals may come from two different sources or from the same source at different times. The coherence of time-lagged signals from a single source is an excellent indication of the effective lifetime of the signal components as a function of their frequency. Unfortunately, incoherent instrument noise will bias the measurement to lower values and may lead the user of the data to false conclusions about the longevity of significant features. The new method may be used whenever both the signal and noise power spectra are known and the noise is incoherent both with the signal and with itself at the applicable time delays. It provides a corrected coherence spectrum given the measured coherence and power spectra. For powerlaw signal spectra and instrumental white noise, the correction formula takes a particularly simple and explicit form. Since many geophysical signals exhibit powerlaw behavior and most instrument noise spectra approach white noise, the simplified form should be widely applicable in meteorology, oceanography, geology, and planetary geophysics.

Merceret, Francis J.↗

Low Biotoxicity of Mars Analog Soils Suggests that the Surface of Mars May be Habitable for Terrestrial Microorganisms

Recent studies on the interactive effects of hypobaria, low temperatures, and CO2-enriched anoxic atmospheres on the growth of 37 species of mesophilic bacteria identified 14 potential biocidal agents that might affect microbial survival and growth on the martian surface. Biocidal or inhibitory factors include (not in priority): (1) solar UV irradiation, (2) low pressure, (3) extreme desiccating conditions, (4) extreme diurnal temperature fluctuations, (5) solar particle events, (6) galactic cosmic rays, (7) UV-glow discharge from blowing dust, (8) solar UV-induced volatile oxidants [e.g., O2(-), O(-), H2O2, O3], (9) globally distributed oxidizing soils, (10) extremely high salts levels [e.g., MgCl2, NaCl, FeSO4, and MgSO4] in surficial soils at some sites on Mars, (11) high concentrations of heavy metals in martian soils, (12) likely acidic conditions in martian fines, (13) high CO2 concentrations in the global atmosphere, and (14) perchlorate-rich soils. Despite these extreme conditions several studies have demonstrated that dormant spores or vegetative cells of terrestrial microorganisms can survive simulated martian conditions as long as they are protected from UV irradiation. What has not been explored in depth are the effects of potential biotoxic geochemical components of the martian regolith on the survival and growth of microorganisms. The primary objectives of the research included: (1) prepare and characterize Mars analog soils amended with potential biotoxic levels of sulfates, salts, acidifying minerals, etc.; and (2) use the simulants to conduct biotoxicity assays to determine if terrestrial microorganisms from spacecraft can survive direct exposure to the analog soils.

Schuerger, A. C.↗

DC and Structured Electric Fields Observed on the C/NOFS Satellite and Their Association with Longitude, Plasma Density, and Solar Activity

Observations of DC electric fields and associated E x B plasma drifts gathered by the Vector Electric Field Investigation (VEFI) on the Air Force Communication/Navigation Outage Forecasting System (C/NOFS) satellite are presented. We show statistical averages of the vector fields and resulting E x B plasma flows for the first three years of operations as a function of season, longitude, local time, and Fl 0.7 conditions. Magnetic field data from the VEFI science magnetometer are used to compute the plasma flows. Although typically displaying eastward and outward-directed fields during the day and westward and downward-directed fields at night, the data from DC electric field detector often reveal variations from this pattern that depend on longitude, solar activity, and plasma density. Clear "wave-4" tidal effects in both electric field components have been detected and will be presented. Zonal plasma drifts show a marked variation with solar activity and may be used as a proxy for neutral winds at night. Evidence for pre-reversal enhancements in the meridional drifts that depend on solar activity is present for some longitudes, and are corroborated by clear evidence in the plasma density data that the spacecraft journeyed below the F-peak during evenings when the rise in the ionosphere is most pronounced. In addition to DC electric fields, the data reveal considerable electric field structures at large scales (approx 100's of km) that are usually confined to the nightside. Although such electric field structures are typically associated with plasma density depletions and structures, what is surprising is the number of cases in which large amplitude, structured DC electric fields are observed without a significant plasma density counterpart structure, including their appearance at times when the ambient plasma density appears relatively quiescent. We investigate the mapping of structured electric fields along magnetic field lines from distant locations and consider tropospheric thunderstorm sources to explain some of the observations. The dependence of the structuring on season and solar activity will be reported and discussed.

Pfaff, Robert↗

Sprayable Phase Change Coating Thermal Protection Material

NASA has expressed a need for reusable, environmentally friendly, phase change coating that is capable of withstanding the heat loads that have historically required an ablative thermal insulation. The Space Shuttle Program currently relies on ablative materials for thermal protection. The problem with an ablative insulation is that, by design, the material ablates away, in fulfilling its function of cooling the underlying substrate, thus preventing the insulation from being reused from flight to flight. The present generation of environmentally friendly, sprayable, ablative thermal insulation (MCC-l); currently use on the Space Shuttle SRBs, is very close to being a reusable insulation system. In actual flight conditions, as confirmed by the post-flight inspections of the SRBs, very little of the material ablates. Multi-flight thermal insulation use has not been qualified for the Space Shuttle. The gap that would have to be overcome in order to implement a reusable Phase Change Coating (PCC) is not unmanageable. PCC could be applied robotically with a spray process utilizing phase change material as filler to yield material of even higher strength and reliability as compared to MCC-1. The PCC filled coatings have also demonstrated potential as cryogenic thermal coatings. In experimental thermal tests, a thin application of PCC has provided the same thermal protection as a much thicker and heavier application of a traditional ablative thermal insulation. In addition, tests have shown that the structural integrity of the coating has been maintained and phase change performance after several aero-thermal cycles was not affected. Experimental tests have also shown that, unlike traditional ablative thermal insulations, PCC would not require an environmental seal coat, which has historically been required to prevent moisture absorption by the thermal insulation, prevent environmental degradation, and to improve the optical and aerodynamic properties. In order to reduce the launch and processing costs of a reusable space vehicle to an affordable level, refurbishment costs must be substantially reduced. A key component of such a cost effective approach is the use of a reusable, phase change, thermal protection coating.

Richardson, Rod W.↗

NASA Marshall Space Flight Center Tri-gas Thruster Performance Characterization

Historically, spacecraft reaction control systems have primarily utilized cold gas thrusters because of their inherent simplicity and reliability. However, cold gas thrusters typically have a low specific impulse. It has been determined that a higher specific impulse can be achieved by passing a monopropellant fluid mixture through a catalyst bed prior to expulsion through the thruster nozzle. This research analyzes the potential efficiency improvements from using tri-gas, a mixture of hydrogen, oxygen, and an inert gas, which in this case is helium. Passing tri-gas through a catalyst causes the hydrogen and oxygen to react and form water vapor, ultimately heating the exiting fluid and generating a higher specific impulse. The goal of this project was to optimize the thruster performance by characterizing the effects of varying several system components including catalyst types, catalyst lengths, and initial catalyst temperatures.

Dorado, Vanessa↗

Treatment of Solid Rocket Motors that Complies with Established Protocols to Ensure Planetary Protection

This presentation discusses recent work being conducted by the National Aeronautics and Space Administration (NASA) at Marshall Space Flight Center (MSFC) to evaluate various methods that could be employed to provide for planetary protection of those solar system bodies that are candidates for extraterrestrial life, thus preventing contamination of such bodies. MSFC is presently involved in the development phase of the Europa Lander De-Orbital Stage (DOS) braking motor. In order to prevent bio-contamination of this Jovian satellite, three paths are currently being considered. The first is (1) Bio-Reduction of those microscopic organisms in or on the vehicle (in this case a solid rocket motor (SRM)) that might otherwise be transported during the mission. Possible methods being investigated include heat sterilization, application or incorporation of biocide materials, and irradiation. While each method can be made to work, effects on the SRM's components (propellant, liner, insulation, etc.) could well prove deleterious. A second path would be use of (2) Bio-Barrier material(s). So long as such barrier(s) can maintain their integrity, planetary protection should be afforded. Under the harsh conditions encountered during extended spaceflight (vacuum, temperature extremes, radiation), however, such barrier(s) could well experience a breach. Finally, a third path would be to perform (3) Pyrotechnic Sterilization of the SRM during its end-of-mission phase. Multiple pyrotechnic units would be triggered to ensure activation of such an event and provide for a final sterilization before vehicle impact. In light of Europa's stringent bio-reduction targets, the final and best choice to minimize risk will probably be some combination of the above.

Stefanski, Philip L.↗

Fabrication and Performance of NiCuCoFeMn High Entropy Alloy Nanopastes for Brazing Inconel 718

Overview: High entropy alloys (HEAs) are a class of metallic alloys consisting of 5 plus elemental components and have four core effects - 1. High mixing entropy - 2. Sluggish diffusion kinetics - 3. High lattice distortion - 4. Cocktail effect; Boron-free, silicon-free brazing materials for nickel superalloys to avoid brittle intermetallic and eutectic phase formation; Size-dependent melting point depression can eliminate the need for boron, silicon and other melting point depressants; A Ni-Mn-Fe-Co-Cu HEA with low solidus and liquidus temperatures (1080 °C and 1150 °C) was developed; Low solidus and liquidus temperatures of the HEA combined with the nanoscale melting point depression in this study; Bulk HEA fabricated by induction melting of elemental powders; HEA nanoparticles (NPs) fabricated by ball milling of the HEA micropowder; Inconel 718 was laser brazed in air using the HEA and bulk and NP performances are compared.

Bridges, Denzel↗

High-Resolution Mapping of SO2 Using Airborne Observations from the GeoTASO Instrument During the KORUS-AQ Field Study: PCA-Based Vertical Column Retrievals

The Geostationary Trace gas and Aerosol Sensor Optimization (GeoTASO) instrument is an airborne hyperspectral spectrometer measuring backscattered solar radiation in the ultraviolet (290–400 nm) and visible (415–695 nm) wavelength regions. This paper presents high-resolution sulfur dioxide (SO2) maps over the Korean Peninsula, produced by SO2 retrievals from GeoTASO measurements during the Korea–United States Air Quality Field Study (KORUS-AQ) from May to June 2016. The highly sensitive GeoTASO instrument with a spatial resolution of ~250 m × 250 m can detect point emission sources of SO2 within its fields of view, even without merging multiple overlapping observations. To retrieve SO2 vertical columns from the GeoTASO measurements, we apply an algorithm based on principal component analysis (PCA), which is effective in suppressing noise and biases in SO2 retrievals. The retrievals successfully capture SO2 plumes and various point sources such as power plants, a petrochemical complex, and a steel mill, located in South Chungcheong Province, some of which are not detected by a ground-based in situ measurement network. Spatial distributions of SO2 from GeoTASO observations in source areas are consistent with those from the Stack Tele-Monitoring System reports and airborne in situ SO2 measurements. Comparisons of SO2 retrievals from GeoTASO and existing satellite sensors demonstrate the significance of high-resolution SO2 observations, by indicating that GeoTASO detects small SO2 emission sources that are not precisely resolved by single overpasses of satellites. To assess future geostationary SO2 observations having a higher spatial resolution, we upscale the GeoTASO SO2 retrievals to a spatial resolution of the Geostationary Environment Monitoring Spectrometer (GEMS). Since the upscaled GeoTASO retrievals also detect SO2 plumes clearly, we expect from GEMS to identify even small SO2 emission sources over Asia.

Chong, Heesung↗

Flight-Test Evaluation of Airframe Noise Mitigation Technologies

A series of flight tests targeting airframe noise reduction was planned and executed under the NASA Flight Demonstrations and Capabilities project. The objectives of the tests were two-fold: to evaluate the aeroacoustic performance of several noise reduction technologies in a relevant environment and to generate a comprehensive database for advancing the state of the art in simulation-based airframe noise prediction methodologies. These technologies – an Adaptive Compliant Trailing Edge flap, main landing gear fairings, and gear cavity treatments – were integrated on a NASA Gulfstream G-III aircraft to determine their effectiveness, both on a component-level (individually) and a system-level (combined) basis. With the aircraft flying an approach pattern and the engines set at ground idle, extensive acoustic measurements were acquired using a phased microphone array system. Detailed analyses of the gathered acoustic data clearly demonstrate that significant noise reduction was achieved for the flap and main landing gear components.

Khorrami, Mehdi R.↗

Development of Acoustic Mufflers for Cabin Noise Reduction in Orion Spacecraft

Controlling cabin acoustic noise levels in the Crew Module (CM) of the Orion spacecraft is critical to ensure adequate speech intelligibility, to avoid fatigue, and prevent any possibility of temporary and permanent hearing loss to the crew. The primary source of cabin noise for the on-orbit phase of the mission is from the Environmental Control and Life Support System (ECLSS) which recycles and conditions breathing air and maintains cabin pressurization through its duct network and components. Unfortunately, as a side effect, noise from the ECLSS fans propagates through theses ducts and emanate into the cabin habitable volume via the ECLSS inlet and outlets. To mitigate excessive duct-borne noise, two ECLSS mufflers have been designed to provide significant acoustic transmission loss (TL) so that the cabin noise requirements can be met. Each muffler is meant to be installed in the ducting of the ECLSS air inlet and outlet sides, respectively. Packaging constraints and tight volume requirements necessitated the mufflers to be of complex geometry and compatible with the bends of the ECLSS duct layout. To design and characterize the acoustic performance of the inlet and outlet mufflers, computational acoustic models were developed using the Finite Element Method (FEM) with 𝑤𝑎𝑣𝑒଺ vibroacoustic software. Characterization of the acoustic material and perforations in the mufflers were addressed with poroelastic theory. Once the mufflers were designed on paper and its TL predicted, prototypes of these mufflers were created using additive manufacturing. The muffler prototypes were subsequently tested for acoustic TL in the laboratory with various con-figurations of acoustic materials. Comparing the analytical predictions to the test performance yielded excellent correlation for acoustic TL and demonstrated significant broadband noise attenuation. The ECLSS mufflers are currently scheduled to be installed on the Artemis II Crew Module (CM) of the Orion spacecraft and will provide significant cabin comfort to crew during the mission.

Indranil Dandaroy↗

Folded Optical Design for High Fidelity Atmospheric Emulation With A Spatial Light Modulator

Atmospheric emulators based on spatial light modulators offer the ability to test atmospheric propagation effects on a laser communication component’s performance in the laboratory setting. To create a high-fidelity atmospheric emulator, details of the optical design are key. This paper discusses the optical design choices and refinements that enabled the creation of a system that was verified to recreate multi-layer turbulence with high fidelity up to D/r 0 =50. Optical design choices that affect the fidelity discussed in this paper include the characteristics of the input laser, the spatial light modulator, the holograms, the image relay optical components, and the spatial filter. Also included in this paper is a comparison of the chosen folded optical layout to an alternative angled layout.

Atmospheric turbulence↗

Folded Optical Design for High Fidelity Atmospheric Emulation With A Spatial Light Modulator

Atmospheric emulators based on spatial light modulators offer the ability to test atmospheric propagation effects on a laser communication component’s performance in the laboratory setting. To create a high-fidelity atmospheric emulator, details of the optical design are key. This paper discusses the optical design choices and refinements that enabled the creation of a system that was verified to recreate multi-layer turbulence with high fidelity up to D/r0 =50. Optical design choices that affect the fidelity discussed in this paper include the characteristics of the input laser, the spatial light modulator, the holograms, the image relay optical components, and the spatial filter. Also included in this paper is a comparison of the chosen folded optical layout to an alternative angled layout.

Atmospheric turbulence↗

Assembly and Integration Status of a High Fidelity Ground Test Bed for the Water Processor Assembly

The Water Recovery System (WRS) is a critical component of life support aboard the International Space Station (ISS) and will play an essential role in future missions beyond Low Earth Orbit (LEO). Its primary functional units – the Urine Processor Assembly (UPA), Brine Processor Assembly (BPA), and Water Processor Assembly (WPA) – must be evaluated for extended operation, dormancy resilience, material obsolescence, and reliability under exploration-driven constraints. Ground testing is vital for developing these technologies and generating statistically relevant reliability assessments, which requires extended runtime under integrated, Flight-like conditions. Currently, no high-fidelity, fully integrated WPA ground test bed exists to support these objectives. To address this gap, NASA is developing a WPA test bed at Marshall Space Flight Center (MSFC) that combines downgraded ISS flight hardware with functionally flight-like components in a cost-effective configuration while maintaining priority hardware investigations. This paper describes the current status of hardware assembly and integration, outlines key challenges such as simulating microgravity effects and mitigating obsolescence, and presents future test objectives including software development, reliability assessments, dormancy studies, and exploration-oriented upgrades.

Mary-Elizabeth Davis↗

Assembly and Integration Status of a High Fidelity Ground Test Bed for the Water Processor Assembly

The Water Recovery System (WRS) is a critical component of life support aboard the International Space Station (ISS) and will play an essential role in future missions beyond Low Earth Orbit (LEO). Its primary functional units – the Urine Processor Assembly (UPA), Brine Processor Assembly (BPA), and Water Processor Assembly (WPA) – must be evaluated for extended operation, dormancy resilience, material obsolescence, and reliability under exploration-driven constraints. Ground testing is vital for developing these technologies and generating statistically relevant reliability assessments, which requires extended runtime under integrated, Flight-like conditions. Currently, no high-fidelity, fully integrated WPA ground test bed exists to support these objectives. To address this gap, NASA is developing a WPA test bed at Marshall Space Flight Center (MSFC) that combines downgraded ISS flight hardware with functionally flight-like components in a cost-effective configuration while maintaining priority hardware investigations. This paper describes the current status of hardware assembly and integration, outlines key challenges such as simulating microgravity effects and mitigating obsolescence, and presents future test objectives including software development, reliability assessments, dormancy studies, and exploration-oriented upgrades.

Water Processor Assembly↗