Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - SWEEPBACK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

Design and evaluation of active cooling systems for Mach 6 cruise vehicle wings

Active cooling systems, which included transpiration, film, and convective cooling concepts, are examined. Coolants included hydrogen, helium, air, and water. Heat shields, radiation barriers, and thermal insulation are considered to reduce heat flow to the cooling systems. Wing sweep angles are varied from 0 deg to 75 deg and wing leading edge radii of 0.05 inch and 2.0 inches are examined. Structural temperatures are varied to allow comparison of aluminum alloy, titanium alloy, and superalloy structural materials. Cooled wing concepts are compared among themselves, and with the uncooled concept on the basis of structural weight, cooling system weight, and coolant weight.

Mcconarty, W. A.↗

Flow field predictions for a slab delta wing at incidence

Theoretical results are presented for the structure of the hypersonic flow field of a blunt slab delta wing at moderately high angle of attack. Special attention is devoted to the interaction between the boundary layer and the inviscid entropy layer. The results are compared with experimental data. The three-dimensional inviscid flow is computed numerically by a marching finite difference method. Attention is concentrated on the windward side of the delta wing, where detailed comparisons are made with the data for shock shape and surface pressure distributions. Surface streamlines are generated, and used in the boundary layer analysis. The three-dimensional laminar boundary layer is computed numerically using a specially-developed technique based on small cross-flow in streamline coordinates. In the rear sections of the wing the boundary layer decreases drastically in the spanwise direction, so that it is still submerged in the entropy layer at the centerline, but surpasses it near the leading edge. Predicted heat transfer distributions are compared with experimental data.

Conti, R. J.↗

Exploratory investigation of factors affecting the wing tip vortex

An investigation was conducted in the Langley full-scale tunnel to study some factors affecting the tip vortex of a wing. It was found that there was a pronounced effect of Reynolds number on the tip-vortex core size. An attempt was made to determine what aerodynamic parameters, such as lift, drag, or induced drag, influence the size of the vortex core, but no particular function of the parameters was found to be superior to all others. Various spoilers placed on the upper and lower surfaces of the wing to increase the boundary-layer thickness resulted in a reduction in the vorticity as determined from the tuft grid. Various solid objects placed in the vortex core downstream of the wing tip seemed to decrease the vorticity within the vortex core.

Scheiman, J.↗

Supersonic aerodynamic characteristics of a low-aspect-ratio missile model with wing and tail controls and with tails in line and interdigitated

A study has been made to determine the aerodynamic characteristics of a low-aspect ratio cruciform missile model with all-movable wings and tails. The configuration was tested at Mach numbers from 1.50 to 4.63 with the wings in the vertical and horizontal planes and with the wings in a 45 deg roll plane with tails in line and interdigitated.

Graves, E. B.↗

Analysis of the effect of engine characteristics on the external aerodynamics of STOL wing propulsion systems

The effects of engine presssure ratio, engine size, and engine location on the pressure distribution, lift coefficient, and flow field of a STOL wing propulsion system are presented. The flow variables of the engines are included in the two-dimensional potential flow analysis by considering the effects of mass flow coefficient at the engine inlet and thrust coefficient at the engine exit. A functional relation between these coefficients and engine pressure ratio is given. The results of this study indicate that the effect of engine pressure ratio on the external aerodynamics is a function of engine location. For engines located on the bottom of the wing, the highest pressure ratio engine resulted in the highest lift coefficient. For engines located on the top of the wing, the lowest pressure ratio engine resulted in the highest lift coefficient.

Albers, J. A.↗

Space shuttle: Static aerodynamic characteristics and control effectiveness of two delta wing orbiter configurations (M equals 0.6 to 4.96)

Two 0.00325-scale models of a space shuttle orbiter were tested in trisonic wind tunnel to obtain force, static stability, and control effectiveness data by six component internal strain gauge balance. Two separate configurations were tested; however, the fuselage and basic wing were of one-piece construction. The configurations were varied by replacing the straight wing tip extensions with upswept wing tips. Directional stability was provided for one configuration by a centerline vertical tail. Due to the one-piece body/wing construction, no body-alone data were obtained. The effect of tip fins and vertical tail size were, however, investigated. Both configurations were tested over a Mach range of 0.6 to 4.96 with data taken at angles of attack from minus 4 deg to 60 deg and at angles of sideslip from minus 4 deg to 10 deg.

Ellis, R. R.↗

Preliminary noise tests of the engine-over-the-wing concept. i: 30 deg - 60 deg flap position

The results of preliminary acoustic tests of the engine over the wing concept are summarized. The tests were conducted with a small wing section model (32 cm chord) having two flaps set at the landing position, which is 30 and 60 deg respectively. The engine exhaust was simulated by an air jet from a convergent nozzle having a nominal diameter of 5.1 centimeters. Factors investigated for their effect on noise include nozzle location, wing shielding, flap leakage, nozzle shape, exhaust deflectors, and internally generated exhaust noise.

Reshotko, M.↗

Wind tunnel investigation of a large scale 35 deg swept wing jet transport model with an external blowing triple slotted flap

An investigation was conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an externally jet-augmented flap system that would augment lift and provide direct-lift control. The model had a 35 deg swept wing of aspect ratio 7.82 and two side-by-side engines mounted on a single pylon under each wing close to the fuselage. The lift of the flap system was augmented by jet engine exhaust impingement on the triple-slotted flap surfaces. The rearmost flap provided direct lift control. Results were obtained for several combinations of flap deflections at gross thrust coefficients from 0 to 2.0. Three-component longitudinal data are presented with four engines operating. Limited longitudinal and lateral data are presented for asymmetric and symmetric thrust conditions with three engines operating. For the same overall flap deflection, lift coefficient and maximum lift coefficient were improved 13 and 7 percent compared to coefficients obtained with a double-slotted flap configuration. A maximum lift coefficient of 6.3 was obtained at a gross thrust coefficient of 2.0. At the same flap deflection lateral and directional trim moment requirements with an engine inoperative were reduced 55 and 33 percent, respectively, compared to those with the engines located farther outboard on the wing. Trim moment requirements in pitch were also reduced significantly. However, pitching-moment instability occurred and increased with gross thrust coefficient.

Aoyagi, K.↗

Flight measurements of buffet characteristics of the F-104 airplane for selected wing-flap deflections

A flight program was conducted on the F-104 airplane to investigate the effects of moderate deflections of wing leading- and trailing-edge flaps on the buffet characteristics at subsonic and transonic Mach numbers. Selected deflections of the wing leading and trailing-edge flaps, individually and in combination, were used to assess buffet onset, intensity, and frequency; lift curves; and wing-rock characteristics for each configuration. Increased deflection of the trailing-edge flap delayed the buffet onset and buffet intensity rise to a significantly higher airplane normal-force coefficient. Deflection of the leading-edge flap produced some delay in buffet onset and the resulting intensity rise at low subsonic speeds. Increased deflection of the trailing-edge flap provided appreciable lift increments in the angle-of-attack range covered, whereas the leading-edge flap provided lift increments only at high angles-of-attack. The pilots appreciated the increased maneuvering envelope provided by the flaps because of the improved turn capability.

Friend, E. L.↗

Reduction of wave drag by antisymmetric arrangement of wings and bodies.

The wave interference effects for bodies or wings in a mirror-symmetric arrangement, and in an antisymmetric arrangement are discussed. It is shown that while in the case of a mirror-symmetric arrangement large adverse interference effects can be observed, antisymmetric arrangements provide comparatively much smaller wave drags. The single continuous wing panels also adapt themselves more readily to varying angles of obliquity, and hence, to varying flight speeds. A detailed review is presented of the previous work on the aerodynamic properties and flight stability of oblique elliptic wing combinations. A possible mode of application of these combinations to transport aircraft operating at moderate supersonic speeds is suggested.

Jones, R. T.↗

Wind-tunnel studies of wing wake turbulence.

Description of velocity measurements made in the wake of wings in the Ames 7 x 10 ft wind tunnel. Distributions of velocity components were measured with a three-wire anemometer up to 12 chord lengths downstream of a CV-990 aircraft model and a rectangular wing. Results show that increasing the drag increases the vortex core radius, reduces the maximum tangential velocities, and increases the magnitude of axial velocity defects. For the rectangular wing, axial velocity changes from a defect (wake flow) for angles of attack less than 9 deg to an excess (jet flow) for angles of attack greater than 9 deg. Wind-tunnel measurements of the near flowfield are compared with flight measurements of the far flowfield.

Chigier, N. A.↗

Delta wing separation can dominate shuttle dynamics.

The unsteady aerodynamics of the delta wing, high cross range, shuttle orbiter have been investigated. Three potentially dangerous flow separation phenomena involving the delta wing have been identified, each of which could seriously compromise the flight dynamics. They are (1) leeside shock-induced separation, (2) sudden leading-edge stall, and (3) the subsonic leading-edge vortex and vortex burst. Each of these unsteady flow phenomena can be triggered by control surface deflection. Furthermore, wing stall and control-induced separation effects interact with the relatively large fuselage, causing simultaneous alteration of the lateral-directional stability. Trajectory shaping may be the most powerful means of dealing with these stall effects.

Reding, J. P.↗

Numerical method for design of minimum-drag supersonic wing camber with constraints on pitching moment and surface deformation

A numerical method, based on linearized theory, for designing minimum-drag supersonic wing camber surfaces of arbitrary planform for a given lift, with options for constraining the pitching moment and/or the surface deformation at the trailing edge of the root chord and for selecting any desired combination of eight specified wing-loading distributions to be employed in the optimization procedure is presented. Two examples are given to illustrate applications of the method. The results indicate that relatively small drag penalties are incurred in designing wings to be self-trimming and to have a reasonable camber surface.

Sorrells, R. B.↗

Longitudinal aerodynamic and propulsion characteristics of a propulsive-wing V/STOL model at high subsonic speeds

The aerodynamic and propulsion characteristics of a 1/6-scale propulsive-wing V/STOL air-powered model was investigated over the Mach number range from 0.40 to 0.96 and at angles of attack from -5 deg to 15 deg for several fan rotational speeds. Three fanduct-exit configurations were tested, including two exit areas. The model with 25-percent-thick wing had a drag-rise Mach number of 0.85, which is typical of aircraft with thinner, conventional, unswept wings.

Salters, L. B., Jr.↗

Jet noise of an augmentor wing-advanced supersonic transport

A preliminary mission study was made of the range and jet noise of an advanced supersonic transport (AST) employing an augmentor wing and four duct burning turbofan engines. The airplane weight and aerodynamic characteristics of the Boeing 2707-300 airplane with a gross weight of 750,000 pounds and 234 passengers was used for the study. Engine thrust was fixed at 58,000 pounds per engine and engine size was increased to obtain the required thrust at reduced power settings for jet noise reduction. Turbofan engine core noise was reduced to FAR 36 noise levels and lower by proper selection of turbine inlet temperature, bypass ratio and fan pressure ratio. The study showed that an augmentor wing can reduce the bypass jet noise sufficiently so that total noise levels below FAR 36 can be attained without significant range penalties if the augmentor wing can be designed without severe weight and performance penalties.

Franciscus, L.↗

Analysis of high-aspect-ratio jet-flap wings of arbitrary geometry

An analytical technique to compute the performance of an arbitrary jet-flapped wing is developed. The solution technique is based on the method of Maskell and Spence in which the well-known lifting-line approach is coupled with an auxiliary equation providing the extra function needed in jet-flap theory. The present method is generalized to handle straight, uncambered wings of arbitrary planform, twist, and blowing (including unsymmetrical cases). An analytical procedure is developed for continuous variations in the above geometric data with special functions to exactly treat discontinuities in any of the geometric and blowing data. A rational theory for the effect of finite wing thickness is introduced as well as simplified concepts of effective aspect ratio for rapid estimation of performance.

Lissaman, P. B. S.↗

Dual-fuselage aircraft having yawable wing and horizontal stabilizer

An aircraft configuration consisting of a pair of fuselages parallel to each other and connected by a main wing and a horizontal stabilizer which pivot on the fuselages is described. The pivotal attachment allows the wing to be yawed relative to the fuselages for high speed flight while at the same time spreading the weight and volume distribution of the aircraft along the direction of flight. The main wing is curved upward at the tips to compensate for any roll tendencies caused by its yawed position.

Jones, R. T.↗

Noise tests of a model engine-over-the-wing STOL configuration using a multijet nozzle with deflector

Noise data were obtained with a small scale model stationary STOL configuration that used an eight lobe mixer nozzle with deflector mounted above a 32-cm-chord wing section. The factors varied to determine their effect upon the noise were wing flap angle, nozzle shape, nozzle location, deflector configuration, and jet velocity. The noise from the mixer nozzle model was compared to the noise from a model using a circular nozzle of the same area. The mixer nozzle model was quieter at the low to middle frequencies, while the circular nozzle was quieter at high frequencies. The perceived noise level (PNL) was calculated for an aircraft 10 times larger than the model. The PNL at 500 feet for the mixer nozzle turned out to be within 1 db of the PNL for the circular nozzle. For some configurations at highly directional broadband noise, which could be eliminated by changes in nozzle and/or deflector location, occurred below the wing.

Olsen, W. A.↗