Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

Measurement of surface microtopography

Acquisition of ground truth data for use in microwave interaction modeling requires measurement of surface roughness sampled at intervals comparable to a fraction of the microwave wavelength and extensive enough to adequately represent the statistics of a surface unit. Sub-centimetric measurement accuracy is thus required over large areas, and existing techniques are usually inadequate. A technique is discussed for acquiring the necessary photogrammetric data using twin film cameras mounted on a helicopter. In an attempt to eliminate tedious data reduction, an automated technique was applied to the helicopter photographs, and results were compared to those produced by conventional stereogrammetry. Derived root-mean-square (RMS) roughness for the same stereo-pair was 7.5 cm for the automated technique versus 6.5 cm for the manual method. The principal source of error is probably due to vegetation in the scene, which affects the automated technique but is ignored by a human operator.

Wall, S. D.↗

Rubber friction on road surfaces: Experiment and theory for low sliding speeds

We study rubber friction for tire tread compounds on asphalt road surfaces. The road surface topographies are measured using a stylus instrument and atomic force microscopy, and the surface roughness power spectra are calculated. The rubber viscoelastic modulus mastercurves are obtained from dynamic mechanical analysis measurements and the large-strain effective modulus is obtained from strain sweep data. The rubber friction is measured at different temperatures and sliding velocities, and is compared to the calculated data obtained using the Persson contact mechanics theory. We conclude that in addition to the viscoelastic deformations of the rubber surface by the road asperities, there is an important contribution to the rubber friction from shear processes in the area of contact. The analysis shows that the latter contribution may arise from rubber molecules (or patches of rubber) undergoing bonding-stretching-debonding cycles as discussed in a classic paper by Schallamach.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A new process-based and scale-aware desert dust emission scheme for global climate models – Part I: Description and evaluation against inverse modeling emissions

Desert dust accounts for most of the atmosphere's aerosol burden by mass and produces numerous important impacts on the Earth system. However, current global climate models (GCMs) and land-surface models (LSMs) struggle to accurately represent key dust emission processes, in part because of inadequate representations of soil particle sizes that affect the dust emission threshold, surface roughness elements that absorb wind momentum, and boundary-layer characteristics that control wind fluctuations. Furthermore, because dust emission is driven by small-scale (~ 1 km or smaller) processes, simulating the global cycle of desert dust in GCMs with coarse horizontal resolutions (~ 100 km) presents a fundamental challenge. This representation problem is exacerbated by dust emission fluxes scaling nonlinearly with wind speed above a threshold wind speed that is sensitive to land-surface characteristics. Here, we address these fundamental problems underlying the simulation of dust emissions in GCMs and LSMs by developing improved descriptions of (1) the effect of soil texture on the dust emission threshold, (2) the effects of nonerodible roughness elements (both rocks and green vegetation) on the surface wind stress, and (3) the effects of boundary-layer turbulence on driving intermittent dust emissions. We then use the resulting revised dust emission parameterization to simulate global dust emissions in a standalone model forced by reanalysis meteorology and land-surface fields. We further propose (4) a simple methodology to rescale lower-resolution dust emission simulations to match the spatial variability of higher-resolution emission simulations in GCMs. The resulting dust emission simulation shows substantially improved agreement against regional dust emissions observationally constrained by inverse modeling. We thus find that our revised dust emission parameterization can substantially improve dust emission simulations in GCMs and LSMs.

54 ENVIRONMENTAL SCIENCES↗

Journal Pre-proof3D printed polylactic acid and acrylonitrile butadiene styrene fluidicstructures for biological applications: tailoring bio-material interfaceviasurface modification

Three-dimensional (3D) printing is a rapidly growing technology that best fits for cell culture and other biological applications due to its potential to build immensely complex structures from customized designs. However, use of 3D printed structures for cell adhesion, proliferation, and activation requires tailoring of surface characteristics. In this context, this work investigates the use of two biocompatible 3D printable polymer materials, Poly-L-lactic Acid (PLA) and Acrylonitrile Butadiene Styrene (ABS) for bio applications, and the effect of their post-printing surface modification processes to achieve desired bio functionality. Three post-printing surface modification techniques, alkaline hydrolysis, ultraviolet ozone plasma irradiation and gold thin film deposition are performed with the objective of introducing useful levels of surface functionalities. Poly-L-lysine (PLL) labelled with FITC chromophore is immobilized on the surface modified samples following standard protocols. The effect of surface roughness and porosity of the 3D printed structures on the polypeptide immobilization is compared on as-printed versus mechanically polished surfaces. Different characterization methods, viz., Fluorescence microscopy, Raman Spectroscopy and UV–vis spectroscopy, are used to study the efficacy of the surface modification and PLL immobilization techniques. Our results demonstrated denser PLL attachment on polished hydrolyzed PLA and ABS surfaces which enables the use of these printable polymers for a range of applications such as tissue scaffolds and microfluidics.

3D Printing, PLA, ABS, Biodegradable Polymer, Surf↗

Reaction of Hydrazine with Solution- and Vacuum-Prepared Selectively Terminated Si(100) Surfaces: Pathways to the Formation of Direct Si–N Bonds

Here, the reactivity of liquid hydrazine (N 2 H 4 ) with respect to H-, Cl-, and Br-terminated Si(100) surfaces was investigated to uncover the principles of nitrogen incorporation into the interface. This process has important implications in a wide variety of applications, including semiconductor surface passivation and functionalization, nitride growth, and many others. The use of hydrazine as a precursor allows for reactions that exclude carbon and oxygen, the primary sources of contamination in processing. In this work, the reactivity of N 2 H 4 with H- and Cl-terminated surfaces prepared by traditional solvent-based methods and with a Br-terminated Si(100) prepared in ultrahigh vacuum was compared. The reactions were studied with X-ray photoelectron spectroscopy, atomic force microscopy, and scanning tunneling microscopy, and the observations were supported by computational investigations. The H-terminated surface led to the highest level of nitrogen incorporation; however, the process proceeds with increasing surface roughness, suggesting possible etching or replacement reactions. In the case of Cl-terminated (predominantly dichloride) and Br-terminated (monobromide) surfaces, the amount of nitrogen incorporation on both surfaces after the reaction with hydrazine was very similar despite the differences in preparation, initial structure, and chemical composition. Density functional theory was used to propose the possible surface structures and to analyze surface reactivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Calibration, modeling, parameterization, and verification of the instrument transfer function of an interferometric microscope

Interferometric microscopes are used to measure surface roughness, from which the computed power spectral density function can be used to extract bandwidth-limited values of the various surface properties, such as root-mean-square (rms) height and slope errors. Measurements with a microscope equipped with different objectives that have an overlapping spatial frequency range usually give different rms results over the common frequency bandwidth. This is a result of different instrument transfer functions (ITFs) that attenuate spatial frequencies by different amounts over the overlapping range. We report on the use of binary pseudo-random array (BPRA) standards to characterize the ITF of an interferometric microscope with the various objectives. We use a simple model of a 1D binary Results show that the spectrum for an undersampled array is a cosine function, rather than a straight line, constant white noise spectrum. We have an analytical model of the ITF that includes the effects of an obscured aperture and defocus, in addition to the usual parameters of numerical aperture, wavelength, and sampling period. In addition, the model includes the effect of aliasing of spatial frequency components beyond the Nyquist back into the sub-Nyquist region. We compare the model PSD predictions to the measurements performed with different objectives. Departures of the measured PSDs from the model predictions indicate that there are higher-order ITF corrections yet to be identified and included in the model.

Takacs, PZ↗

Evaluation of MS-122 mold releases

Miller Stephenson polytetrafluoroethylene-based mold releases were evaluated; the mold releases include MS-122E, MS-122SE, MS-122AD, MS-122ADL, and MS-122XD. The mold releases were tested for cure inhibition of Sylgard 184 90/10. These mold releases were also tested for sheer flow stability through a defined gap on a uranium alloy surface. Mold releases MS-122E, MS-122SE, MS-122AD, MS-122ADL, and MS-122XD were all tested. SEM images comparing the lay down of each mold release on a flat silicon surface were also compared. MS-122 XD showed signs of cure inhibition of Sylgard 184 90/10. All mold releases were detected on uranium alloy surfaces via Infrared Spectroscopy (FT-IR) after flowing Sylgard 184 90/10 across the uranium surface indicating the mold release coating is stable under flow. All SEM images of the mold releases studied are comparable showing rough surfaces with micron-sized particles.

36 MATERIALS SCIENCE↗

Real-time measurement of ice growth during simulated and natural icing conditions using ultrasonic pulse-echo techniques

Results of tests to measure ice accretion in real-time using ultrasonic pulse-echo techniques are presented. Tests conducted on a 10.2 cm diameter cylinder exposed to simulated icing conditions in the NASA Lewis Icing Research Tunnel and on an 11.4 cm diameter cylinder exposed to natural icing conditions in flight are described. An accuracy of + or - 0.5 mm is achieved for real-time ice thickness measurements. Ice accretion rate is determined by differentiating ice thickness with respect to time. Icing rates measured during simulated and natural icing conditions are compared and related to icing cloud parameters. The ultrasonic signal characteristics are used to detect the presence of surface water on the accreting ice shape and thus to distinguish between dry ice growth and wet growth. The surface roughness of the accreted ice is shown to be related to the width of the echo signal received from the ice surface.

Hansman, R. J., Jr.↗

Microwave backscatter coefficients of artificially grown first-year sea ice

The radar backscattering coefficient of simulated first year sea ice was measured at 5.2, 9.6, 13.6, and 16.6 GHz, using a dual-antenna FM-CW scatterometer. The measurements were corrected for antenna separation and beamwidth, to obtain true values of scattering coefficient. Above 15 deg, snow-covered and rough gray ice have similar angular responses, while the decrease in scattering coefficient with incidence angle is more rapid for smoother surfaces. True scattering coefficients and surface roughness data estimated with an antenna-beamwidth correction based on a physical-optics model give values close to those measured.

Xue, D.↗

Science synergism study for EOS on evolution of desert surfaces

The effectiveness of EOS data as a basis for the study of desert surfaces' evolution is presently evaluated for both long and short term geomorphic evolution. Attention is given to the usefulness of such sensor systems planned for EOS as MODIS for regional vegetation distribution/variability monitoring, HIRIS for visible-near IR observations, TIMS for lithological identification, HMMR and SSMI for soil characteristics, LASA for atmospheric profiles, SAR for surface roughness, ALT for two-dimensional topography, ACR for the calibration of imaging sensors, and ERBE for climate modeling and regional surface albedo variation determinations.

Farr, Tom G.↗

Ground truth measurement for the analysis of airborne SAR data recorded over Oberpfaffenhofen, FRG, 1989

As a preliminary investigation to the joint multiparameter SIR-C/X-SAR shuttle experiment of NASA/JPL (USA), DLR (FRG), and PSN (Italy) which is scheduled for the year 1992 an airborne SAR campaign was conducted over Oberpfaffenhofen, FRG, in August 1989. Primarily this campaign was planned to test and verify equipment and algorithms developed at the DLR to calibrate multifrequency polarimetric SAR data. Oberpfaffenhofen is designated as one of the super test sites for the SIR-C/X-SAR experiment which will be imaged under all circumstances except severe mission errors. A super test site drives radar parameters and look directions and the recorded SAR data will be calibrated. In addition ancillary data will be available for the site. During the airborne STAR campaign conducted in the week of August 14th 1989 various sensor types were used to record remote sensing data over the calibration test site and its vicinity: the polarimetric DC-8 JPL-SAR (P-, L-, C-band), the DLR airborne SAR (C-, X-band), color infrared aerial photography (DLR), and the truck-mounted scatterometer (C- and X-band) of the Institute for Navigation, University of Stuttgart (INS). Because of this variety of different sensor types used and out of the fact that sufficiently large forested and agriculturally used areas were planned to be covered by these sensors, the interest of several German research groups involved in investigations concerning SAR land applications arose. The following groups carried out different ground-truth measurements: University of Bonn, Institute for plant cultivation (plant morphology and moisture content); University of Braunschweig, Institute for Geography (soil moisture and surface roughness); University of Freiburg, Institute for Geography (dielectric soil properties, landuse); and University of Munich, Institute for Geography (landuse inventory, plant, surface, and soil parameters). This paper presents the joint ground truth activities of the Institute for Geography, University of Munich, and the German Remote Sensing Data Center of the DLR.

Bayer, T.↗

Epitaxial two dimensional aluminum films on silicon (111) by ultra-fast thermal deposition

Aluminum thin films are known for their extremely rough surface, which is detrimental for applications such as molecular electronics and photonics, where protrusions cause electrical shorts or strong scattering. We achieved atomically flat Al films using a highly non-equilibrium approach. Ultra-fast thermal deposition (UFTD), at rates >10 nm/s, yields RMS roughness of 0.4 to 0.8 nm for 30-50 nm thick Al films on variety of substrates. For UFTD on Si(111) substrates, the top surface follows closely the substrate topography (etch pits), indicating a 2D, layer-by-layer growth. The Al film is a mixture of (100) and (111) grains, where the latter are commensurate with the in-plane orientation of the underlying Si (epitaxy). We show the use of these ultra-smooth Al films for highly reproducible charge-transport measurements across a monolayer of alkyl phosphonic acid as well as for plasmonics applications by directly patterning them by focused ion beam to form a long-range ordered array of holes. UFTD is a one-step process, with no need for annealing, peeling, or primer layers. It is conceptually opposite to high quality deposition methods, such as MBE or ALD, which are slow and near-equilibrium processes. For Al, though, we find that limited diffusion length (and good wetting) is critical for achieving ultra-smooth thin films.

36 MATERIALS SCIENCE↗

Supersonic Traveling Crossflow Wave Characteristics in Ground and Flight Tests

This paper continues analysis of data acquired in a series of supersonic crossflow transition experiments on a 65° swept- wing model tested in both wind tunnel and flight. Flow visualization data are summarized to provide context for the swept-wing instability mechanisms of interest. Unsteady pressure measurements obtained near the wing model leading edge (LE) are studied using 2nd- and 3rd-order statistical methods to extract traveling crossflow wave characteristics from these data. Comparisons between tunnel and flight data with boundary-layer (BL) Linear Stability Theory (LST) predictions provide insights into BL transition phenomena similarities and differences observed in tests using the same swept-wing model configurations. Comparisons of unsteady pressure data results for wing LE configurations with and without distributed-roughness-element (DRE) patterns installed, suggest traveling crossflow disturbance growth is reduced when this type of flow control is applied. A brief stud y of different background surface roughness levels on the wing LE suggests the potential for another flow control approach to promote laminar flow on swept wings using streamwise-biased surface finishes.

Lewis R Owens↗

Attachment-Line Transition Due to Roughness on a 76 Degree Swept Cylinder at Mach 1.6

Experiments were conducted on a 76 deg. swept cylinder to establish the conditions for the attachment-line transition process with, and without, surface roughness in a low-disturbance ("quiet"), Mach number 1.6 flow. Local flow parameters were estimated from pressure measurements. These were in good agreement with predictions from an Euler code (CFL3D) and a boundary layer code (BL3D). Hot-wires and Schlieren photography were used to determine the state of the boundary layer. It was found that, for a near-adiabatic wall condition and a smooth surface, the attachment-line, boundary-layer remained laminar up to the highest attainable Reynolds number (R-bar of 790). Transition under the influence of trip wires was found to depend on wind-tunnel disturbance levels and the onset conditions have been established. Results suggest that current design practice, which is based upon data from conventional ("noisy") tunnels, may be highly conservative.

Coleman, Colin P.↗

The response of the SSM/I to the marine environment. Part 2: A parameterization of the effect of the sea surface slope distribution on emission and reflection

Based on a geometric optics model and the assumption of an isotropic Gaussian surface slope distribution, the component of ocean surface microwave emissivity variation due to large-scale surface roughness is parameterized for the frequencies and approximate viewing angle of the Special Sensor Microwave/Imager. Independent geophysical variables in the parameterization are the effective (microwave frequency dependent) slope variance and the sea surface temperature. Using the same physical model, the change in the effective zenith angle of reflected sky radiation arising from large-scale roughness is also parameterized. Independent geophysical variables in this parameterization are the effective slope variance and the atmospheric optical depth at the frequency in question. Both of the above model-based parameterizations are intended for use in conjunction with empirical parameterizations relating effective slope variance and foam coverage to near-surface wind speed. These empirical parameterizations are the subject of a separate paper.

Petty, Grant W.↗

Synchronizing spatio-temporal chaos with imperfect models: A stochastic surface growth picture

We study the synchronization of two spatially extended dynamical systems where the models have imperfections. We show that the synchronization error across space can be visualized as a rough surface governed by the Kardar-Parisi-Zhang equation with both upper and lower bounding walls corresponding to nonlinearities and model discrepancies, respectively. Two types of model imperfections are considered: parameter mismatch and unresolved fast scales, finding in both cases the same qualitative results. The consistency between different setups and systems indicates that the results are generic for a wide family of spatially extended systems.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electrical passivation and chemical functionalization of SiC surfaces by chlorine termination

We have developed a straightforward plasma-based method which yields chlorine-terminated n-type 6H-SiC surfaces. Atomic force microscopy shows that the surface roughness is not affected by the plasma processing. Additionally, x-ray photoelectron spectroscopy reveals a significant reduction in oxygen, and a corresponding rise of chlorine core level intensities, following halogen termination. Contact potential difference and surface photovoltage measurements show formation of negative surface dipoles and approximately flat band surface potentials after chlorine termination of (0001) n-type 6H-SiC (built-in voltage V{sub bi}<20 meV). Starting from halogenated surfaces, we demonstrate both ultraviolet light-induced and thermally-induced functionalization with alkene-derived self-assembled organic monolayers.

36 MATERIALS SCIENCE↗

EFFECT OF SURFACE CONDITION ON SPALLATION BEHAVIOR OF OXIDE SCALE ON SS 441 SUBSTRATE USED IN SOFC

As operating temperature of SOFC decreases, ferritic stainless steel has attracted a great deal of attention for its use as an interconnect in SOFCs because of its gas-tightness, low electrical resistivity, ease of fabrication, and cost-effectiveness. However, oxidation reaction of the metallic interconnects in a typical SOFC working environment is unavoidable. The growth stresses in the oxide scale and on the scale/substrate interface combined with the thermal stresses induced by thermal expansion coefficient mismatch between the oxide scale and the substrate may lead to scale delamination/buckling and eventual spallation during stack cooling, which can lead to serious cell performance degradation. Therefore, the interfacial adhesion strength between the oxide scale and substrate is crucial to the reliability and durability of the metallic interconnect in SOFC operating environments. In this paper, we investigated the effect of the surface conditions on the interfacial strength of oxide scale and SS441 substrate experimentally. Contrary to the conventional sense, it was found that rough surface of SS441 substrate will decrease the interfacial adhesive strength of the oxide scale and SS441 substrate

oxide scale spallation↗