Search NASA⌕ Search

SEARCH · Search NASA

Results for “structural dynamics testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

Composite load spectra for select space propulsion structural components

The work performed to develop composite load spectra (CLS) for the Space Shuttle Main Engine (SSME) using probabilistic methods. The three methods were implemented to be the engine system influence model. RASCAL was chosen to be the principal method as most component load models were implemented with the method. Validation of RASCAL was performed. High accuracy comparable to the Monte Carlo method can be obtained if a large enough bin size is used. Generic probabilistic models were developed and implemented for load calculations using the probabilistic methods discussed above. Each engine mission, either a real fighter or a test, has three mission phases: the engine start transient phase, the steady state phase, and the engine cut off transient phase. Power level and engine operating inlet conditions change during a mission. The load calculation module provides the steady-state and quasi-steady state calculation procedures with duty-cycle-data option. The quasi-steady state procedure is for engine transient phase calculations. In addition, a few generic probabilistic load models were also developed for specific conditions. These include the fixed transient spike model, the poison arrival transient spike model, and the rare event model. These generic probabilistic load models provide sufficient latitude for simulating loads with specific conditions. For SSME components, turbine blades, transfer ducts, LOX post, and the high pressure oxidizer turbopump (HPOTP) discharge duct were selected for application of the CLS program. They include static pressure loads and dynamic pressure loads for all four components, centrifugal force for the turbine blade, temperatures of thermal loads for all four components, and structural vibration loads for the ducts and LOX posts.

Newell, J. F.↗

The Structure and Dynamics of the Corona - Heliosphere Connection

Determining the source at the Sun of the slow solar wind is one of the major unsolved problems in solar and heliospheric physics. First, we review the existing theories for the slow wind and argue that they have difficulty accounting for both the observed composition of the wind and its large angular extent. A new theory in which the slow wind originates from the continuous opening and closing of narrow open field corridors, the S-Web model, is described. Support for the S-Web model is derived from MHD solutions for the quasisteady corona and wind during the time of the August 1, 2008 eclipse. Additionally, we perform fully dynamic numerical simulations of the corona and heliosphere in order to test the S-Web model as well as the interchange model proposed by Fisk and co-workers. We discuss the implications of our simulations for the competing theories and for understanding the corona - heliosphere connection, in general.

Antiochos, Spiro K.↗

The Structure and Dynamics of the Corona - Heliosphere Connection

Determining the source at the Sun of the slow solar wind is one of the major unsolved problems in solar and heliospheric physics. First, we review the existing theories for the slow wind and argue that they have difficulty accounting for both the observed composition of the wind and its large angular extent. A new theory in which the slow wind originates from the continuous opening and closing of narrow open field corridors, the S-Web model, is described. Support for the S-Web model is derived from MHD solutions for the quasisteady corona and wind during the time of the August 1, 2008 eclipse. Additionally, we perform fully dynamic numerical simulations of the corona and heliosphere in order to test the S-Web model as well as the interchange model proposed by Fisk and co-workers. We discuss the implications of our simulations for the competing theories and for understanding the corona - heliosphere connection, in general.

Antiochos, Spiro K.↗

The prediction of structural response to buffet flow: A state-of-the-art review

Certain aspects of the dynamic system being discussed are reviewed and important structural and aerodynamic quantities of the system are discussed. A theoretical model is presented which relates these quantities to each other. These quantities are then each, in turn, considered in terms of the state of the art of determining the quantities and in terms of areas where further research is needed. The similarity laws and scaling relationships applicable to determining buffet structural response are then discussed, and areas where simplification is required or may be permissible are mentioned. Finally, the various types of model tests pertinent to predicting response of the aircraft structure to buffet flow are discussed.

Hanson, P. W.↗

Program of research in flight dynamics in the JIAFS at NASA-Langley Research Center

The program objectives are fully defined in the original proposal entitled 'Program of Research in Flight Dynamics in the Joint Institute for the Advancement of Flight Sciences (JIAFS) at NASA-Langley Research Center,' which was originated March 20, 1975 and in the renewal of the research program dated December 1, 1991. The program includes four major topics: (1) the improvement of existing methods and development of new methods for flight test data analysis; (2) the application of these methods to real flight test data obtained from advanced airplanes; (3) the correlation of flight results with wind tunnel measurements; and (4) the modeling, and control of aircraft, space structures, and spacecraft.

Source record↗

The NASA Lewis Research Center: An Economic Impact Study

The NASA Lewis Research Center (LeRC), established in 1941, is one of ten NASA research centers in the country. It is situated on 350 acres of land in Cuyahoga County and occupies more than 140 buildings and over 500 specialized research and test facilities. Most of LeRC's facilities are located in the City of Cleveland; some are located within the boundaries of the cities of Fairview Park and Brookpark. LeRC is a lead center for NASA's research, technology, and development in the areas of aeropropulsion and selected space applications. It is a center of excellence for turbomachinery, microgravity fluid and combustion research, and commercial communication. The base research and technology disciplines which serve both aeronautics and space areas include materials and structures, instrumentation and controls, fluid physics, electronics, and computational fluid dynamics. This study investigates LeRC's economic impact on Northeast Ohio's economy. It was conducted by The Urban Center's Economic Development Program in Cleveland State University's Levin College of Urban Affairs. The study measures LeRC's direct impact on the local economy in terms of jobs, output, payroll, and taxes, as well as the indirect impact of these economic activities when they 'ripple' throughout the economy. To fully explain LeRC's overall impact on the region, its contributions in the areas of technology transfer and education are also examined. The study uses a highly credible and widely accepted research methodology. First, regional economic multipliers based on input-output models were used to estimate the effect of LERC spending on the Northeast Ohio economy. Second, the economic models were complemented by interviews with industrial, civic, and university leaders to qualitatively assess LeRC's impact in the areas of technology transfer and education.

Austrian, Ziona↗

Flight Testing of the Gulfstream Quiet Spike(TradeMark) on a NASA F-15B

Gulfstream Aerospace has long been interested in the development of an economically viable supersonic business jet (SBJ). A design requirement for such an aircraft is the ability for unrestricted supersonic flight over land. Although independent studies continue to substantiate that a market for a SBJ exists, regulatory and public acceptance challenges still remain for supersonic operation over land. The largest technical barrier to achieving this goal is sonic boom attenuation. Gulfstream's attention has been focused on fundamental research into sonic boom suppression for several years. This research was conducted in partnership with the NASA Aeronautics Research Mission Directorate (ARMD) supersonic airframe cruise efficiency technical challenge. The Quiet Spike, a multi-stage telescopic nose boom and a Gulfstream-patented design (references 1 and 2), was developed to address the sonic boom attenuation challenge and validate the technical feasibility of a morphing fuselage. The Quiet Spike Flight Test Program represents a major step into supersonic technology development for sonic boom suppression. The Gulfstream Aerospace Quiet Spike was designed to reduce the sonic boom signature of the forward fuselage for an aircraft flying at supersonic speeds. In 2004, the Quiet Spike Flight Test Program was conceived by Gulfstream and NASA to demonstrate the feasibility of sonic boom mitigation and centered on the structural and mechanical viability of the translating test article design. Research testing of the Quiet Spike consisted of numerous ground and flight operations. Each step in the process had unique objectives, and involved numerous test team members from the NASA Dryden Flight Research Center (DFRC) and Gulfstream Aerospace. Flight testing of the Quiet Spike was conducted at the NASA Dryden Flight Research Center on an F-15B aircraft from August, 2006, to February, 2007. During this period, the Quiet Spike was flown at supersonic speeds up to Mach 1.8 at the maximum design dynamic pressure of 685 pounds per square foot. Extension and retraction tests were conducted at speeds up to Mach 1.4. The design of the Quiet Spike to shape the forward shock wave environment of the aircraft was confirmed during near-field shock wave probing at Mach 1.4. Thirty-two flights were performed without incident and all project objectives were achieved. The success of the Quiet Spike Flight Test Program represents an important step towards developing commercial aircraft capable of supersonic flight over land within the continental United States and in international airspace.

Smolka, James W.↗

Development and Validation of a Multidisciplinary Tool for Accurate and Efficient Rotorcraft Noise Prediction (MUTE)

A physics-based, systematically coupled, multidisciplinary prediction tool (MUTE) for rotorcraft noise was developed and validated with a wide range of flight configurations and conditions. MUTE is an aggregation of multidisciplinary computational tools that accurately and efficiently model the physics of the source of rotorcraft noise, and predict the noise at far-field observer locations. It uses systematic coupling approaches among multiple disciplines including Computational Fluid Dynamics (CFD), Computational Structural Dynamics (CSD), and high fidelity acoustics. Within MUTE, advanced high-order CFD tools are used around the rotor blade to predict the transonic flow (shock wave) effects, which generate the high-speed impulsive noise. Predictions of the blade-vortex interaction noise in low speed flight are also improved by using the Particle Vortex Transport Method (PVTM), which preserves the wake flow details required for blade/wake and fuselage/wake interactions. The accuracy of the source noise prediction is further improved by utilizing a coupling approach between CFD and CSD, so that the effects of key structural dynamics, elastic blade deformations, and trim solutions are correctly represented in the analysis. The blade loading information and/or the flow field parameters around the rotor blade predicted by the CFD/CSD coupling approach are used to predict the acoustic signatures at far-field observer locations with a high-fidelity noise propagation code (WOPWOP3). The predicted results from the MUTE tool for rotor blade aerodynamic loading and far-field acoustic signatures are compared and validated with a variation of experimental data sets, such as UH60-A data, DNW test data and HART II test data.

Liu, Yi↗

CFD Study of the J2-X LOX Two-Bladed Inducer in the Presence of a Circumferential Groove

Results are presented of a computational fluid dynamics (CFD) study done in support of water flow experiments of the J-2X Oxidizer Turbopump (OTP) 2-bladed inducer with a circumferential groove that were conducted at Marshall Space Flight Center (MSFC). Sub-scale water flow testing results indicate that the circumferential groove greatly reduces synchronous cavitation and subsequent bearing loads at a minimal performance cost, but the energy reappears as high order cavitation (HOC) that spans a relatively large frequency range. Thus, HOC may have implications for the full-scale OTP inducer in terms of reduced structural margin at higher mode frequencies. Simulations using the LOCI-Stream CFD program were conducted in order to explore the root physical cause of the HOC. It was found that the axial recirculation pattern in the circumferential groove causes high-swirl fluid to interact with the nearly-axial incoming fluid just above the inducer blades. The high-shear interface between the fluids is Kelvin-Helmholtz unstable, resulting in trains of low pressure regions or 'pearls' forming near the upstream edge of the groove. When the pressure in these regions becomes low enough and they get cut by the blade leading edge, HOC is thought to occur. Although further work is required, the numerical models indicate that the root cause of HOC is hydrodynamic. That is, the pearls are always present, even when cavitation is not. Comparisons to ongoing water flow experiments will be discussed, as well as predictions for the full-scale OTP inducer.

Coker, Robert↗

Characterization of Subsurface Flow Dynamics for Forecasting of Solar Activity

Evolution of large-scale magnetic field structures in the solar photosphere and corona is controlled by motions beneath the visible surface of the Sun. Subsurface plasma flows play a critical role in formation and evolution of active regions and their activity. We analyze subsurface flow maps provided by the local helioseismology pipeline from the Helioseismic and Magnetic Imager (HMI) data on board the Solar Dynamics Observatory, and investigate links between flow characteristics and magnetic activity. The primary goal is to determine flow descriptors, which can improve solar activity forecasts. In particular, by employing machine learning classifiers, we test how the flow helicity and velocity shear descriptors can improve the prediction of initiation of flares and CME eruptions.

Kosovichev, Alexander↗

Design and Fabrication of the Langley Aerodrome No. 8 - Distributed Electric Propulsion VTOL Testbed

The Langley Aerodrome No. 8 (LA-8) is a distributed electric propulsion, vertical takeoff and landing (VTOL) aircraft that is being used for wind tunnel testing and free flight testing at the NASA Langley Research Center. The intent of the LA-8 project is to provide a low-cost, modular test bed for technologies in the area of Advanced Air Mobility which includes electric urban and short regional flight. The methods used on the LA-8 provide a rapid means to verify aerodynamic, acoustic, and flight dynamics analysis of new electric VTOL and short takeoff and landing (STOL) designs. In addition, the flight vehicle will be used to help develop test processes for FAA flight vehicle airworthiness certification and for the development of robust flight control algorithms that are tolerant of failures. A new approach is being used on test vehicle design that makes extensive use of 3-D printing. Although materials used in 3-D printing have less strength than traditional materials used for NASA’s wind tunnel and flight models, strategic placement of load-carrying structures allows the aircraft to meet structural criteria while also enabling easy changes to be made in the vehicle design, such as the outer mold line. Modularity of the vehicle’s main components allows rapid changes to the vehicle configuration for comparative evaluation of alternate designs. Finally, a description is given of detailed inertia measurements of the flight vehicle using compound pendulum swing methods.

Urban air mobility↗

In-space construction and dynamics of large space structures

The types of equipment and structures that will be required to construct very large spacecraft in space are discussed. One of the basic issues that must be resolved is the appropriate mix of humans and machines in the construction process. While the use of robots offers the potential for reducing the number of extra-vehicular activity (EVA) hours required for particular construction operations, the availability of humans greatly increases the reliability of complex construction tasks. A hybrid system is described which makes the best use of man and machine to provide a highly reliable and versatile construction approach. Such a system will provide an efficient method for constructing large spacecraft until fully automated, robotic devices can be perfected. Details are given on an extensive ground test program which was designed to evaluate and demonstrate large spacecraft construction. A discussion is presented on the use of the Space Station Freedom, or an appropriate derivative, as a construction facility. Finally, a construction scenario and assembly timelines are presented for constructing a 20-meter-diameter high precision reflector.

Mikulas, Martin M., Jr.↗

The navigation system of the JPL robot

The control structure of the JPL research robot and the operations of the navigation subsystem are discussed. The robot functions as a network of interacting concurrent processes distributed among several computers and coordinated by a central executive. The results of scene analysis are used to create a segmented terrain model in which surface regions are classified by traversibility. The model is used by a path planning algorithm, PATH, which uses tree search methods to find the optimal path to a goal. In PATH, the search space is defined dynamically as a consequence of node testing. Maze-solving and the use of an associative data base for context dependent node generation are also discussed. Execution of a planned path is accomplished by a feedback guidance process with automatic error recovery.

Thompson, A. M.↗

Correlation and assessment of structural airplane crash data with flight parameters at impact

Crash deceleration pulse data from a crash dynamics program on general aviation airplanes and from transport crash data were analyzed. Structural airplane crash data and flight parameters at impact were correlated. Uncoupled equations for the normal and longitudinal floor impulses in the cabin area of the airplane were derived, and analytical expressions for structural crushing during impact and horizontal slide out were also determined. Agreement was found between experimental and analytical data for general aviation and transport airplanes over a relatively wide range of impact parameter. Two possible applications of the impulse data are presented: a postcrash evaluation of crash test parameters and an assumed crash scenario.

Carden, H. D.↗

Construction and Utilization of a Beowulf Computing Cluster: A User's Perspective

Lockheed Martin Space Operations - Stennis Programs (LMSO) at the John C Stennis Space Center (NASA/SSC) has designed and built a Beowulf computer cluster which is owned by NASA/SSC and operated by LMSO. The design and construction of the cluster are detailed in this paper. The cluster is currently used for Computational Fluid Dynamics (CFD) simulations. The CFD codes in use and their applications are discussed. Examples of some of the work are also presented. Performance benchmark studies have been conducted for the CFD codes being run on the cluster. The results of two of the studies are presented and discussed. The cluster is not currently being utilized to its full potential; therefore, plans are underway to add more capabilities. These include the addition of structural, thermal, fluid, and acoustic Finite Element Analysis codes as well as real-time data acquisition and processing during test operations at NASA/SSC. These plans are discussed as well.

Woods, Judy L.↗

Multi-Terrain Earth Landing Systems Applicable for Manned Space Capsules

A key element of the President's Vision for Space Exploration is the development of a new space transportation system to replace the Shuttle that will enable manned exploration of the moon, Mars, and beyond. NASA has tasked the Constellation Program with the development of this architecture, which includes the Ares launch vehicle and Orion manned spacecraft. The Orion spacecraft must carry six astronauts and its primary structure should be reusable, if practical. These requirements led the Constellation Program to consider a baseline land landing on return to earth. To assess the landing system options for Orion, a review of current operational parachute landing systems such as those used for the F-111 escape module and the Soyuz is performed. In particular, landing systems with airbags and retrorockets that would enable reusability of the Orion capsule are investigated. In addition, Apollo tests and analyses conducted in the 1960's for both water and land landings are reviewed. Finally, tests and dynamic finite element simulations to understand land landings for the Orion spacecraft are also presented.

Fasanella, Edwin L.↗

Multi-Terrain Earth Landing Systems Applicable for Manned Space Capsules

A key element of the President's Vision for Space Exploration is the development of a new space transportation system to replace Shuttle that will enable manned exploration of the moon, Mars, and beyond. NASA has tasked the Constellation Program with the development of this architecture, which includes the Ares launch vehicle and Orion manned spacecraft. The Orion spacecraft must carry six astronauts and its primary structure should be reusable, if practical. These requirements led the Constellation Program to consider a baseline land landing on return to earth. To assess the landing system options for Orion, a review of current operational parachute landing systems such as those used for the F-111 escape module and the Soyuz is performed. In particular, landing systems with airbags and retrorockets that would enable reusability of the Orion capsule are investigated. In addition, Apollo tests and analyses conducted in the 1960's for both water and land landings are reviewed. Finally, tests and dynamic finite element simulations to understand land landings for the Orion spacecraft are also presented.

Fasanella, Edwin L.↗

Workshop on Structural Dynamics and Control Interaction of Flexible Structures

The Hubble Space Telescope features the most exacting line of sight jitter requirement thus far imposed on a spacecraft pointing system. Consideration of the fine pointing requirements prompted an attempt to isolate the telescope from the low level vibration disturbances generated by the attitude control system reaction wheels. The primary goal was to provide isolation from axial component of wheel disturbance without compromising the control system bandwidth. A passive isolation system employing metal springs in parallel with viscous fluid dampers was designed, fabricated, and space qualified. Stiffness and damping characteristics are deterministic, controlled independently, and were demonstrated to remain constant over at least five orders of input disturbance magnitude. The damping remained purely viscous even at the data collection threshold of .16 x .000001 in input displacement, a level much lower than the anticipated Hubble Space Telescope disturbance amplitude. Vibration attenuation goals were obtained and ground test of the vehicle has demonstrated the isolators are transparent to the attitude control system.

Davis, L. P.↗