Search NASA⌕ Search

SEARCH · Search NASA

Results for “3D Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

Assessing the Impact of a Novel TBC Material on Heat Transfer in a Spark Ignition Engine through 3D CFD-FEA Co-Simulation Routine

Thermal barrier coatings (TBCs) have been of interest since the 1970s for application in internal combustion (IC) engines. Thin TBCs exhibit a temperature swing phenomenon wherein wall temperatures dynamically respond to the transient working-gas temperature throughout the engine cycle, thus reducing the temperature difference driving the heat transfer. Determining these varying wall temperatures is necessary to evaluate and study the effect of coatings on wall heat transfer. This study focuses on developing a 3D computational fluid dynamics (CFD)-finite element analysis (FEA) coupled simulation, or co-simulation, routine to determine the wall temperatures of a piston coated with a thin TBC layer subject to spark ignition combustion heat flux. A CONVERGE 3D-CFD model was used to simulate the combustion process in a single-cylinder, light-duty experimental spark ignition (SI) engine. Transient piston heat transfer analysis was conducted using ABAQUS, a FEA package, under the simulated combustion heat flux load. The effect of the temperature swing phenomenon due to this TBC layer was observed in a CFD simulation by implementing the FEA results as the piston thermal boundary conditions. The boundary conditions were passed between the CFD and FEA tools until a quasi-steady state solution was achieved. Furthermore, a reduction in wall heat transfer was observed due to a reduced temperature difference between the wall and the working gas.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Embedding a Critical Point in a Hadron to Quark–Gluon Crossover Equation of State

It is shown how to embed a critical point in a smooth background equation of state so as to yield the critical exponents and critical amplitude ratios expected of a transition in the same universality class as the liquid–gas phase transition and the 3D Ising model. There are only two independent critical exponents; the relations α + 2β + $\gamma$ = 2 and β(δ - 1) = $\gamma$ arise automatically, as does a new relation between the two critical amplitudes. The resulting equation of state has parameters which may be inferred by hydrodynamic modeling of heavy-ion collisions in the Beam Energy Scan II at the Relativistic Heavy Ion Collider.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Tracing the Emergence of Collectivity Phenomena in Small Systems

We study initial state momentum correlations and event-by-event geometry in p+Pb collisions at $\sqrt{2}$ = 5.02 TeV by following the approach of extending the IP-Glasma model to 3D using JIMWLK rapidity evolution. On examining the non-trivial rapidity dependence of the observables, we find that the geometry is correlated over large rapidity intervals, while the initial state momentum correlations have a relatively short range in rapidity. Based on our results, we discuss implications for the relevance of both effects in explaining the origin of collective phenomena in small systems.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Shattered pellet penetration in low and high energy plasmas on DIII-D

Shattered pellet injection (SPI) has been adopted as the baseline disruption mitigation system for ITER, as the radiative payload penetration into DIII-D plasmas from SPI is superior to those using the massive gas injection (MGI) method. Because of the substantial differences in the energy content of ITER plasma and those in present experiments, reliable 3D MHD modeling, benchmarked against present experiments is needed to project to ITER plasmas. In support of these needs, the depth of SPI fragment penetration in DIII-D plasmas was investigated by injecting SPI into two discharges with vastly different energy content and pedestal height. 400 Torr-L pure Ne fragmented pellets at a velocity of about 200 m s−1 were injected into a 0.2 MJ L-mode discharge and a 2 MJ super H-mode discharge. Results show deep penetration of SPI fragments into low-energy plasmas in DIII-D. SPI fragment penetration is reduced as the plasma energy content increases, with some discharges exhibiting penetration that is confined to the outer regions of the plasma. The injected SPI fragments are also spread out over a distance of about 20 cm, which results in some fragments arriving near the end of or after the thermal quench is over.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Advanced manufacturing development of a composite empennage component for l-1011 aircraft

Tooling concepts were developed which would permit co-couring of the hat stiffeners to the skin to form the cover assembly in a single autoclave cycle. These tooling concepts include the use of solid rubber mandrels, foam mandrels, and formed elastometric bladders. A simplification of the root end design of the cover hat stiffeners was accomplished in order to facilitate fabrication. The conversion of the 3D NASTRAN model from level 15 to level 16 was completed and a successful check run accomplished. A detailed analysis of the thermal load requirement for the environmental chambers was carried out. Based on the thermal analysis, best function requirements, load inputs and ease of access, a system involving four chambers, two for the covers containing 6 and 4 specimens, respectively, and two for the spares containing 6 and 4 specimens, respectively, evolved.

Source record↗

Effects of stratospheric lapse rate on numerically simulated thunderstorm cloud top structure

The study of overshooting midlatitude severe thunderstorm tops has led to the detection of some intriguing patterns. This paper provides a summary of an investigation of the effects of stratospheric stability on thunderstorm cloud top structure, taking into account the utilization of a fully three-dimensional (3D) anelastic model discussed by Schlesinger (1975, 1978, 1984). The layout of model experiments is discussed, giving attention to initial environmental soundings, and initial forcing. The time variation of the vertical velocity extreme is examined, and a description of the mature storm structure is presented. Constant-altitude plane views throughout storm depth are considered along with cloud top height fields. With the stratospheric lapse, the warm region is small and breaks down into separate spots with secondary cold spots downshear of them.

Schlesinger, R. E.↗

Analysis of the low gravity tolerance of Bridgman-Stockbarger crystal growth. I - Steady and impulse accelerations

The effects of steady and impulse-type residual accelerations on dopant distributions during directional solidification in 2D and 3D 'generic' models of the Bridgman-Stockbarger technique are investigated using numerical methods. The calculations are based on the thermophysical properties of molten germanium doped with a low concentration of gallium. A Chebyshev collocation pseudospectral method is used for the solution of the governing momentum-, mass-, species-, and heat-transfer equations. Only convection caused by temperature gradients is considered. It is found that lateral nonuniformity in composition is very sensitive to the orientation of the steady component of the residual gravity vector and to the particular operating conditions under consideration. It is also found that laterally or radially averaged composition profiles are alone insufficient to describe the extent of residual convection in a spacecraft environment. The effects of impulse-type disturbances can be severe and can extend for times on the order of 1000 sec after the termination of the impulse.

Alexander, J. Iwan D.↗

Space shuttle main engine computed tomography applications

For the past two years the potential applications of computed tomography to the fabrication and overhaul of the Space Shuttle Main Engine were evaluated. Application tests were performed at various government and manufacturer facilities with equipment produced by four different manufacturers. The hardware scanned varied in size and complexity from a small temperature sensor and turbine blades to an assembled heat exchanger and main injector oxidizer inlet manifold. The evaluation of capabilities included the ability to identify and locate internal flaws, measure the depth of surface cracks, measure wall thickness, compare manifold design contours to actual part contours, perform automatic dimensional inspections, generate 3D computer models of actual parts, and image the relationship of the details in a complex assembly. The capabilities evaluated, with the exception of measuring the depth of surface flaws, demonstrated the existing and potential ability to perform many beneficial Space Shuttle Main Engine applications.

Sporny, Richard F.↗

On dipolarization and its relation to the substorm current wedge

The near-earth properties of magnetospheric substorms are investigated using the Hesse and Birn (1991) self-consistent 3D MHD model of magnetotail activity. The simulation shows that an increase of Bz, a decrease of the cross-tail current, and an increase of region-1 field-aligned currents occurs roughly simultaneously, consistent with the empirical picture described by McPherron et al. (1973). It was also found that the region where the cross-tail current is reduced and diverted is located tailward from the dipolarization region. The results indicate that the apparent tailward propagation of the dipolarization effects does not support an earlier suggestion that the underlying process is initiated further earthward.

Hesse, Michael↗

Rate calculations for the simultaneous vibrational relaxation and dissociation of nitrogen

Experimental data on vibrational relaxation and dissociation rates in highly nonequilibrium gases are scarce. Recently there have been several attempts at generating these rates by direct calculation of inelastic collision cross-sections. Some issues that need to be considered if such calculations are to be used as a basis for analysis and design are examined. In particular, the following are examined: (1) collinear vs 3D scattering models, (2) accurate intermolecular potentials, (3) closed channels and acceleration schemes, (4) thermal averaging and thermal rates, and (5) code validation. It has been necessary to confront these issues during the course of N2-N2 and N2-N inelastic cross-section calculations.

Gonzales, David A.↗

The VRT gas turbine combustor - Phase II

An innovative annular combustor configuration is being developed for aircraft and other gas turbine engines. This design has the potential of permitting higher turbine inlet temperatures by reducing the pattern factor and providing a major reduction in NO(x) emission. The design concept is based on a Variable Residence Time (VRT) technique which allows large fuel particles adequate time to completely burn in the circumferentially mixed primary zone. High durability of the combustor is achieved by dual-function use of the incoming air. In Phase I, the feasibility of the concept was demonstrated by water analogue tests and 3D computer modeling. The flow pattern within the combustor was as predicted. The VRT combustor uses only half the number of fuel nozzles of the conventional configuration. In Phase II, hardware was designed, procured, and tested under conditions simulating typical supersonic civil aircraft cruise conditions to the limits of the rig. The test results confirmed many of the superior performance predictions of the VRT concept. The Hastelloy X liner showed no signs of distress after nearly six hours of tests using JP5 fuel.

Melconian, Jerry O.↗

Lunar crane system

In many lunar construction scenarios, mechanical cranes in some form will be indispensible in moving large masses around with various degrees of fine positioning. While thorough experience exists in the use of terrestrial cranes new thinking is required about the design of cranes to be used in extraterrestrial construction. The primary driving force for this new thinking is the need to automate the crane system so that space cranes can be operated as telerobotic machines with a large number of automatic capabilities. This is true because in extraterrestrial construction human resources will need to be critically rationed. The design problems of mechanisms and control systems for a lunar crane must deal with at least two areas of performance. First, the automated crane must be capable of maneuvering a large mass, so that when the mass arrives at the target position there are only small vibrations. Secondly, any residue vibrations must be automatically damped out and a fine positioning must be achieved. For extraterrestrial use there are additional challenges to a crane design - for example, to design a crane system so that it can be transformed for other construction uses. This initial project in crane design does not address such additional issues, although they may be the subject of future CSC research. To date the Center has designed and analyzed many mechanisms. The fundamental problem of trade-offs between passively stabilizing the load and actively controlling the load by actuators was extensively studied. The capability of 3D dynamics modeling now exists for such studies. A scaled model of a lunar crane was set up and it has been most fruitful in providing basic understanding of lunar cranes. Due to an interesting scaling match-up, this scaled model exhibits the load vibration frequencies one would expect in the real lunar case. Using the analytical results achieved to date, a laboratory crane system is now being developed as a test bed for verifying a wide variety of mechanisms and control designs. Future development will be aimed at making the crane system a telerobotic test bed into which external sensors such as computer vision systems, and other small robotic devices such as CSC lunar rovers, will be integrated.

Mikulas, Martin M., Jr.↗

The coupling of the troposphere and stratosphere

A linear, time-dependent, primitive-equation, 3D numerical model is used to investigate the dynamical coupling between the troposphere and stratosphere through the vertical propagation of planetry waves. Attention is given to the roles of the tropopause in affecting the propagation of planetary waves and to the extent to which the stratosphere can determine its own wave driving, i.e., the sensitivity of the generation of the wave activity in the troposphere to the change of zonal wind in the stratosphere. Two maxima in Eliassen-Palm (EP) flux convergence are found for wave 1 in high latitudes, one in the upper stratosphere and the other in the upper troposphere. For wave 2 there is a third maximum north of the zero wind line in the tropical stratosphere. The formation of the maximum in EP-flux convergence in the upper troposphere is related to the dissipation of non-WKBJ waves near a local maximum of the refractive index. The existence of the local maximum in refractive index at the tropopause is a result of the great gradient of the buoyancy frequency as well as the vertical shear of the zonal flow there.

Chen, Ping↗

Factors regulating ozone over the United States and its export to the global atmosphere

Attention is given to the factors regulating summertime O3 over the U.S. and its export to the global atmosphere, which are examined via a 3-mo simulation involving a continental-scale 3D photochemical model. It is found that reducing NO(x) emissions by 50 percent from 1985 levels would decrease rural O3 concentrations over the eastern U.S. by about 15 percent under almost all meteorological conditions, while reducing anthropogenic hydrocarbon emissions by 50 percent would have less than a 4 percent effect except in the largest urban plumes. The correlation between O3 concentrations and temperature observed at eastern U.S. sites is attributed in part to the association of high temperatures with regional stagnation, and in part to an actual dependence of O3 production on temperature driven primarily by conversion of NO(x) to PAN.

Jacob, Daniel J.↗

Meso-beta scale numerical simulation studies of terrain-induced jet streak mass and momentum perturbations

An in-depth analysis of observed gravity waves and their relationship to precipitation bands over the Montana mesonetwork during the 11-12 July 1981 CCOPE case study indicated two episodes of coherent waves. While geostrophic adjustment, shearing instability, and terrain were all implicated separately or in combination as possible wave generation mechanisms, the lack of upper-air data within the wave genesis region made it difficult to define the genesis processes from observations alone. The first part of this paper, 3D Numerical Modeling Studies of Terrain-Induced Mass/Momentum Perturbations, employs a mesoscale numerical model to help diagnose the intricate early wave generation mechanisms during the first observed gravity wave episode. The meso-beta scale numerical model is used to study various simulations of the role of multiple geostrophic adjustment processes in focusing a region for gravity wave genesis. The second part of this paper, Linear Theory and Theoretical Modeling, investigates the response of non-resting rotating homogeneous and continuously stratified Boussinesq models of the terrestrial atmosphere to temporally impulsive and uniformly propagating three-dimensional localized zonal momentum sources representative of midlatitude jet streaks. The methods of linear perturbation theory applied to the potential vorticity (PV) and wave field equations are used to study the geostrophic adjustment dynamics. The total zonal and meridional wind perturbations are separated into geostrophic and ageostrophic components in order to define and follow the evolution of both the primary and secondary mesocirculations accompanying midlatitude jetogenesis forced by geostrophic adjustment processes. This problem is addressed to help fill the gap in understanding the dynamics and structure of mesoscale inertia-gravity waves forced by geostrophic adjustment processes in simple two-dimensional quiescent current systems and those produced by mesoscale numerical models simulating the orographic and diabatic perturbation of three-dimensional quasi-geostrophically balanced synoptic scale jet streaks associated with complex baroclinic severe storm producing environments.

Lin, Yuh-Lang↗

Geometry modeling and grid generation using 3D NURBS control volume

The algorithms for volume grid generation using NURBS geometric representation are presented. The parameterization algorithm is enhanced to yield a desired physical distribution on the curve, surface and volume. This approach bridges the gap between CAD surface/volume definition and surface/volume grid generation. Computational examples associated with practical configurations have shown the utilization of these algorithms.

Yu, Tzu-Yi↗

Meshing of a Spiral Bevel Gearset with 3D Finite Element Analysis

Recent advances in spiral bevel gear geometry and finite element technology make it practical to conduct a structural analysis and analytically roll the gearset through mesh. With the advent of user specific programming linked to 3D solid modelers and mesh generators, model generation has become greatly automated. Contact algorithms available in general purpose finite element codes eliminate the need for the use and alignment of gap elements. Once the gearset is placed in mesh, user subroutines attached to the FE code easily roll the gearset through mesh. The method is described in detail. Preliminary results for a gearset segment showing the progression of the contact lineload is given as the gears roll through mesh.

Bibel, George D.↗

Virtual Reality Simulation of the Effects of Microgravity in Gastrointestinal Physiology

The ultimate goal of this research is to create an anatomically accurate three-dimensional (3D) simulation model of the effects of microgravity in gastrointestinal physiology and to explore the role that such changes may have in the pharmacokinetics of drugs given to the space crews for prevention or therapy. To accomplish this goal the specific aims of this research are: 1) To generate a complete 3-D reconstructions of the human GastroIntestinal (GI) tract of the male and female Visible Humans. 2) To develop and implement time-dependent computer algorithms to simulate the GI motility using the above 3-D reconstruction.

Compadre, Cesar M.↗