Search NASA⌕ Search

SEARCH · Search NASA

Results for “High gradient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

Comparison of solution approaches for minimum-fuel, low-thrust, power-limited orbital transfers

An initial assessment of the feasibility of a function space gradient method for computing solutions to minimum-fuel power-limited transfers encompassing a wide range of thrust to weight ratios is conducted. Three transfers between coplanar ellipses are used as test cases. The gradient method performs best at the high end of the thrust to weight ratio range. At the lower end, there is reduced sensitivity of the fuel consumption to the control profiles. The minimum fuel consumption and the trajectory are computed quite accurately but the control profiles are in error. An approximate analytical solution, obtained by Edelbaum using the method of averaging, is discussed.

Mease, Kenneth D.↗

Thermoelastic vibration test techniques

The structural integrity of proposed high speed aircraft can be seriously affected by the extremely high surface temperatures and large temperature gradients throughout the vehicle's structure. Variations in the structure's elastic characteristics as a result of thermal effects can be observed by changes in vibration frequency, damping, and mode shape. Analysis codes that predict these changes must be correlated and verified with experimental data. The experimental modal test techniques and procedures used to conduct uniform, nonuniform, and transient thermoelastic vibration tests are presented. Experimental setup and elevated temperature instrumentation considerations are also discussed. Modal data for a 12 by 50 inch aluminum plate heated to a temperature of 475 F are presented. These data show the effect of heat on the plate's modal characteristics. The results indicated that frequency decreased, damping increased, and mode shape remained unchanged as the temperature of the plate was increased.

Kehoe, Michael W.↗

Determination of the effects of heating on modal characteristics of an aluminum plate with application to hypersonic vehicles

The structural integrity of proposed high speed aircraft can be seriously affected by the extremely high surface temperatures and large temperature gradients throughout the vehicle's structure. Variations in the structure's elastic characteristics as a result of thermal effects can be seen by changes in vibration characteristics. Analysis codes that predict these changes must be correlated and verified with experimental data. Analytical and experimental modal test results are given from uniform, nonuniform, and transient thermoelastic vibration tests of a 12 x 50 x 0.19 aluminum plate. The data show the effect of heat on the modal characteristics of the plate. The results showed that frequencies decreased, damping increased, and mode shapes remained unchanged as the temperature of the plate increased. Analytical predictions provided good correlation with experimental results.

Snyder, H. Todd↗

Modeling of the heat transfer in bypass transitional boundary-layer flows

A low Reynolds number k-epsilon turbulence model and conditioned momentum, energy and turbulence equations were used to predict bypass transition heat transfer on a flat plate in a high-disturbance environment with zero pressure gradient. The use of conditioned equations was demonstrated to be an improvement over the use of the global-time-averaged equations for the calculation of velocity profiles and turbulence intensity profiles in the transition region of a boundary layer. The approach of conditioned equations is extended to include heat transfer and a modeling of transition events is used to predict transition onset and the extent of transition on a flat plate. The events, which describe the boundary layer at the leading edge, result in boundary-layer regions consisting of: (1) the laminar, (2) pseudolaminar, (3) transitional, and (4) turbulent boundary layers. The modeled transition events were incorporated into the TEXSTAN 2-D boundary-layer code which is used to numerically predict the heat transfer. The numerical predictions in general compared well with the experimental data and revealed areas where additional experimental information is needed.

Simon, Frederick F.↗

Infrared Rugates by Molecular Beam Epitaxy

Rugates are optical structures that have a sinusoidal index of refraction (harmonic gradient-index field). As their discrete high/ low index filter counterparts, they can be used as narrow rejection band filters. However, since rugates do not have abrupt interfaces, they tend to have a smaller absorption, hence deliver a higher in band reflectivity. The absence of sharp interfaces makes rugates even more desirable for high-energy narrow band reflectors. In this application, the lack of a sharp interface at the maximum internal standing wave electric field results in higher breakdown strengths. Our method involves fabricating rugates, with molecular beam epitaxy, on GaAs wafers as an Al(x)Ga(1-x)As single-crystal film.

Rona, M.↗

Thermoelastic vibration test techniques

The structural integrity of proposed high speed aircraft can be seriously affected by the extremely high surface temperatures and large temperature gradients throughout the vehicle's structure. Variations in the structure's elastic characteristics as a result of thermal effects can be observed by changes in vibration frequency, damping, and mode shape. Analysis codes that predict these changes must be correlated and verified with experimental data. The experimental modal test techniques and procedures used to conduct uniform, nonuniform, and transient thermoelastic vibration tests are presented. Experimental setup and elevated temperature instrumentation considerations are also discussed. Modal data for a 12 by 50 inch aluminum plate heated to a temperature of 475 F are presented. These data show the effect of heat on the plate's modal characteristics. The results indicated that frequency decreased, damping increased, and mode shape remained unchanged as the temperature of the plate was increased.

Kehoe, Michael W.↗

Refraction of high frequency noise in an arbitrary jet flow

Refraction of high frequency noise by mean flow gradients in a jet is studied using the ray-tracing methods of geometrical acoustics. Both the two-dimensional (2D) and three-dimensional (3D) formulations are considered. In the former case, the mean flow is assumed parallel and the governing propagation equations are described by a system of four first order ordinary differential equations. The 3D formulation, on the other hand, accounts for the jet spreading as well as the axial flow development. In this case, a system of six first order differential equations are solved to trace a ray from its source location to an observer in the far field. For subsonic jets with a small spreading angle both methods lead to similar results outside the zone of silence. However, with increasing jet speed the two prediction models diverge to the point where the parallel flow assumption is no longer justified. The Doppler factor of supersonic jets as influenced by the refraction effects is discussed and compared with the conventional modified Doppler factor.

Khavaran, Abbas↗

Development of an Innovative Algorithm for Aerodynamics-Structure Interaction Using Lattice Boltzmann Method

The lattice Boltzmann equation (LBE) is a kinetic formulation which offers an alternative computational method capable of solving fluid dynamics for various systems. Major advantages of the method are owing to the fact that the solution for the particle distribution functions is explicit, easy to implement, and the algorithm is natural to parallelize. In this final report, we summarize the works accomplished in the past three years. Since most works have been published, the technical details can be found in the literature. Brief summary will be provided in this report. In this project, a second-order accurate treatment of boundary condition in the LBE method is developed for a curved boundary and tested successfully in various 2-D and 3-D configurations. To evaluate the aerodynamic force on a body in the context of LBE method, several force evaluation schemes have been investigated. A simple momentum exchange method is shown to give reliable and accurate values for the force on a body in both 2-D and 3-D cases. Various 3-D LBE models have been assessed in terms of efficiency, accuracy, and robustness. In general, accurate 3-D results can be obtained using LBE methods. The 3-D 19-bit model is found to be the best one among the 15-bit, 19-bit, and 27-bit LBE models. To achieve desired grid resolution and to accommodate the far field boundary conditions in aerodynamics computations, a multi-block LBE method is developed by dividing the flow field into various blocks each having constant lattice spacing. Substantial contribution to the LBE method is also made through the development of a new, generalized lattice Boltzmann equation constructed in the moment space in order to improve the computational stability, detailed theoretical analysis on the stability, dispersion, and dissipation characteristics of the LBE method, and computational studies of high Reynolds number flows with singular gradients. Finally, a finite difference-based lattice Boltzmann method is developed for inviscid compressible flows.

Mei, Ren-Wei↗

An Alternative Hypothesis for How Microgravity Improves Macromolecular Crystal Quality

There is a substantial body of experimental evidence, from this and other laboratories, that strongly suggests that for many proteins crystal nucleation and growth is by addition of associated species that are preformed by reversible concentration-driven self association processes in the bulk solution. We have developed a self-association model for the crystal nucleation and growth of the protein chicken egg lysozyme. The model accounts for the obtained crystal symmetry, explains the observed surface structures, and shows the importance of the symmetry obtained by self-association in solution to the process as a whole. This model also offers a possible mechanism for fluid flow effects on the growth process and how microgravity may affect it. While a single lysozyme molecule is relatively small an octamer in the 43 helix configuration (the proposed average sized growth unit) would have a M.W. approx. 115,000 and dimensions of 5.6 x 5.6 x 7.6 nm. Direct AFM measurements of growth unit incorporation indicate that units as wide as 11.2 nm and as long as 11.4 nm (a 24-mer) commonly attach to the crystal. AFM results from Weichmann et al. (Ultramicroscopy 86, 159-166, 2001) suggest that associated species of up to 40-mers in size add to the (101) faces. These measurements reflect the sizes of units that both added and desorbed from the crystal surface. The larger and less isotropic the associated species the more likely that it will be oriented to some degree in a flowing boundary layer, even at the low flow velocities measured about macromolecule crystals. On Earth, concentration gradient driven flow will maintain a high interfacial concentration, i.e., a high level (essentially that of the bulk solution) of solute association at the interface and higher growth rate. Higher growth rates mean an increased probability that misaligned growth units are trapped by subsequent growth layers before they can be desorbed and try again, or that the desorbing species is more likely to be smaller than the adsorbing species. In microgravity the extended diffusive boundary layer will lower the interfacial concentration. This results in a net dissociation of aggregated species that diffuse in from the bulk solution, i.e., smaller associated species, which are more likely able to make multiple attempts to correctly bind, yielding higher quality crystals.

Pusey, Marc↗

Large Alluvial Fans on Mars

Several dozen distinct alluvial fans, 10 to greater than 40 km long downslope are observed exclusively in highlands craters. Within a search region between 0 deg. and 30 deg. S, alluvial fan-containing craters were only found between 18 and 29 S, and they all occur at around plus or minus 1 km of the MOLA-defined Martian datum. Within the study area they are not randomly distributed but instead form three distinct clusters. Fans typically descend greater than 1 km from where they disgorge from their alcoves. Longitudinal profiles show that their surfaces are very slightly concave with a mean slope of 2 degrees. Many fans exhibit very long, narrow low-relief ridges radially oriented down-slope, often branching at their distal ends, suggestive of distributaries. Morphometric data for 31 fans was derived from MOLA data and compared with terrestrial fans with high-relief source areas, terrestrial low gradient alluvial ramps in inactive tectonic settings, and older Martian alluvial ramps along crater floors. The Martian alluvial fans generally fall on the same trends as the terrestrial alluvial fans, whereas the gentler Martian crater floor ramps are similar in gradient to the low relief terrestrial alluvial surfaces. For a given fan gradient, Martian alluvial fans generally have greater source basin relief than terrestrial fans in active tectonic settings. This suggests that the terrestrial source basins either yield coarser debris or have higher sediment concentrations than their Martian counterpoints. Martian fans and Basin and Range fans have steeper gradients than the older Martian alluvial ramps and terrestrial low relief alluvial surfaces, which is consistent with a supply of coarse sediment. Martian fans are relatively large and of low gradient, similar to terrestrial fluvial fans rather than debris flow fans. However, gravity scaling uncertainties make the flow regime forming Martian fans uncertain. Martian fans, at least those in Holden crater, apparently formed around the time of the Noachian-Hesperian boundary. We infer that these fans formed during an episode of enhanced precipitation (probably snow) and runoff, which exhibited both sudden onset and termination.

Moore, Jeffrey M.↗

Porous Media Approach for Modeling Closed Cell Foam

In order to minimize boil off of the liquid oxygen and liquid hydrogen and to prevent the formation of ice on its exterior surface, the Space Shuttle External Tank (ET) is insulated using various low-density, closed-cell polymeric foams. Improved analysis methods for these foam materials are needed to predict the foam structural response and to help identify the foam fracture behavior in order to help minimize foam shedding occurrences. This presentation describes a continuum based approach to modeling the foam thermo-mechanical behavior that accounts for the cellular nature of the material and explicitly addresses the effect of the internal cell gas pressure. A porous media approach is implemented in a finite element frame work to model the mechanical behavior of the closed cell foam. The ABAQUS general purpose finite element program is used to simulate the continuum behavior of the foam. The soil mechanics element is implemented to account for the cell internal pressure and its effect on the stress and strain fields. The pressure variation inside the closed cells is calculated using the ideal gas laws. The soil mechanics element is compatible with an orthotropic materials model to capture the different behavior between the rise and in-plane directions of the foam. The porous media approach is applied to model the foam thermal strain and calculate the foam effective coefficient of thermal expansion. The calculated foam coefficients of thermal expansion were able to simulate the measured thermal strain during heat up from cryogenic temperature to room temperature in vacuum. The porous media approach was applied to an insulated substrate with one inch foam and compared to a simple elastic solution without pore pressure. The porous media approach is also applied to model the foam mechanical behavior during subscale laboratory experiments. In this test, a foam layer sprayed on a metal substrate is subjected to a temperature variation while the metal substrate is stretched to simulate the structural response of the tank during operation. The thermal expansion mismatch between the foam and the metal substrate and the thermal gradient in the foam layer causes high tensile stresses near the metal/foam interface that can lead to delamination.

Ghosn, Louis J.↗

First-Order Hyperbolic System Method for Time-Dependent Advection-Diffusion Problems

A time-dependent extension of the first-order hyperbolic system method for advection-diffusion problems is introduced. Diffusive/viscous terms are written and discretized as a hyperbolic system, which recovers the original equation in the steady state. The resulting scheme offers advantages over traditional schemes: a dramatic simplification in the discretization, high-order accuracy in the solution gradients, and orders-of-magnitude convergence acceleration. The hyperbolic advection-diffusion system is discretized by the second-order upwind residual-distribution scheme in a unified manner, and the system of implicit-residual-equations is solved by Newton's method over every physical time step. The numerical results are presented for linear and nonlinear advection-diffusion problems, demonstrating solutions and gradients produced to the same order of accuracy, with rapid convergence over each physical time step, typically less than five Newton iterations.

Mazaheri, Alireza↗

Detecting Volcanic Co2 Emissions Hidden in Tropical Volcanic Forests Using Fixed-Wing sUAS

CO2 emissions are among the earliest indicators of subsurface state change and reactivation of volcanic systems and these deep signals reflect in faint diffuse emissions variations on volcanic flanks. Monitoring vast areas of rainforests covering tropical volcanoes is challenging, and space-borne sensors like OCO-2 are not sensitive enough. Fortunately, trees exposed to mild enhancements of CO2 may experience fertilization and build excess CO2 into excess biomass (Cawse-Nicholson, et al. 2018, Biogeosciences). They also process excess CO2 through photosynthesis, measurable by fluorescence (Bogue et al., 2019, Biogeosciences). Furthermore, spaceborne remote sensing instruments have demonstrated increasing NDVI months to years before eruptions, unexplained by other factors (e.g., Houlie et al. 2006, EPSL; Seiler et al. 2017, PLoS One). By providing a means to map large areas of above-canopy CO2 variations over tropical rainforest on the flanks of actively degassing volcanoes, we enable to interpret the signals plants provide in response to excess CO2 with airborne and spaceborne hyperspectral remote sensing methods, including a possible future Surface Biology and Geology (SBG) NASA satellite mission.As a critical step to mature and test this concept, we deployed small unmanned aerial systems (sUAS) using a fixed-wing sUAS designed for autonomous operations and long endurance in extreme environments, without causing significant disturbance of the sampled air. We integrated an in-situ sensor to record the CO2 enhancement field above the forest canopy. Test flight results on the flanks of Turrialba volcano in Costa Rica above forest canopies covering known moderate gas seeps demonstrate the sUAS-borne detection and mapping capabilities of above-canopy elevated CO2 gradients. The strong detection capabilities and high detector signal stability resulted from key system design elements including RF shielding, mechanical stabilization, and calibration procedures. This highly robust system is readily applied for diffuse volcanic CO2 emission studies on active volcanoes covered by dense vegetation.

Volcanic↗

Accelerated Irradiation Testing of Miniature Nuclear Fuel and Cladding Specimens

Qualification of advanced nuclear fuels and materials requires irradiation testing to provide input to predictive models for licensing. Oak Ridge National Laboratory has a long history of performing accelerated irradiation testing and post-irradiation examination (PIE) of miniature material specimens to determine the evolution of microstructure and thermophysical properties, leveraging the High Flux Isotope Reactor, dedicated hot cells, and instruments for handling small, low-level radioactive samples. This work gives a brief overview of irradiation testing of miniature samples to support qualification of advanced fuel cladding materials such as FeCrAl alloys and SiC ceramic matrix composites. More recent work has enabled separate effects irradiation testing of miniature fuel specimens. The small fuel size essentially decouples fuel temperature from fission rate, allowing for highly accelerated testing without large temperature gradients. This paper briefly highlights the new mini fuel irradiation facility and its first set of experiments.

Petrie, Christian↗

MRP and NEAMS Meeting - Current Modeling to Support Experiments

Heat-pipe cooled micro-reactor is currently being actively investigated in the NS&T department at INL. Given the high operation temperature and large temperature gradients in the system, the induced thermal stresses need to be well analyzed and kept within the safety margin. Two commercial FEM software (ABAQUS and STAR-CCM+) have been proposed to simulate and compare for both the temperature and stress distributions for the single heat pipe experiments, with the middle single heat pipe and 6 heaters surrounded. This presentation file is aimed to provide the latest updates for the researchers who is under NEAMS program and involved with the DOE micro-reactor program

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

The Add-A-Source Matrix Calibration of a Large Neutron Box Counter

A general purpose passive neutron box counter has been designed, constructed and factory calibrated. The instrument is intended to sort and assay Transuranic Uranium (TRU) waste according to the Waste Isolation Pilot Plant (WIPP) criteria in containers ranging from drums to large boxes and crates. A multi-position Cf Add-A-Source (AAS) capability has been built into the system to determine gross matrix correction factors. The Cf source capsule runs in a U-shaped guide tube beneath the powered roller conveyor used to move the containers into the assay cavity from the loading station. The factory calibration involved measuring a wide range of matrix materials and densities in 208-liter (55 US-gal.) barrels, Standard Waste Box (SWB), Standard Large Box (SLB-2), and Ten Drum Overpack (TDOP) containers. For each container a Volume Weighted Average (VWA) rate and an AAS perturbation factor was determined and the relationship between them was established for the full range of conditions expected to be encountered operationally. In this paper we describe the calibration procedure which used Cf-252 as a surrogate for Pu-240 to map out the spatial responses for the various container-matrix combinations. A particular challenge was the scale of the measurement campaign which was directly related to the large volume of some of the containers. The reduction of the data was also challenging because for the larger items with high concentrations of hydrogen steep spatial gradients were observed in the response. For this reason simple volume-element averaging of the data to derive VWA quantities was inadequate and numerical-integration approaches of the 3-dimensional maps were explored. The response maps were also used to create point-source contributions to the Total Measurement Uncertainty (TMU), but this work is not the subject of this paper. The wide range in container size also required varying numbers of AAS interrogation position. For the drums a single AAS position was used while for the SWB and TDOP six positions were used to achieve better coverage of the cross-section. The SLB-2 has a larger cross section still and ten positions of the AAS were used for this container. The AAS calibration parameterizations for the various containers will be described along with the difficulties associated with a calibration of large containers. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Joint EM-NE-International Study of Glass Behavior over Geologic Time Scales - 12303

Vitrification has been chosen as the best demonstrated available technology for waste immobilization worldwide. To date, the contributions of physical and chemical processes controlling the long-term glass dissolution rate in geologic disposal remain uncertain, leading to a lack of international consensus on a rate law for glass corrosion. Existing rate laws have overcome uncertainty through conservatism, but a thorough mechanistic understanding of waste form durability in geologic environments would improve public and regulator confidence. If it is possible to take credit for the true durability of the waste form in repository system evaluations, then it is possible to design the repository with less conservatism with concomitant cost savings. To gain a fundamental understanding of the dissolution rate law, six nations have joined together to formulate a joint plan for collaborative research into the mechanisms controlling the long-term corrosion of glass. This report highlights the technical program plan behind the US portion of this effort, with an emphasis on the current understanding (and limitations) of several mechanistic theories for glass corrosion. Some recent results are presented to provide an example of the ongoing research. Atom probe tomography has been used to provide a high-resolution analysis of elemental concentration gradients present at the hydrated glass / pristine glass interface in SON68 after 25.75 years of corrosion in a simulated granitic groundwater at 90 deg. C. The most valuable result of these initial studies is the success of the technique. Characterization by APT had never been previously demonstrated for glass corrosion layers. The resolution of APT is a powerful addition to the tools with which we can investigate the mechanisms dominating glass corrosion. Some other key results of this study include the observation that the elemental interfacial width between the hydrated glass and pristine glass appears to be much sharper (∼2 nm for B, Na and Al) than had been previously measured using nanoSIMS (∼240 nm). It is not clear whether the APT analysis and nanoSIMS characterizations were possibly performed on topographically unique regions, or whether nanoSIMS overestimated the elemental width. However, the APT data seems very convincing that the elemental width can be much sharper than was previously thought. This result calls into question some of the assumptions made for the diffusion-control models of glass dissolution, since such a sharp profile would not match the diffusion coefficients used to date. Other results, such as the observation of apparently layered concentration profiles, show that gel evolution is not as simple as is currently assumed in nearly every model. This task is a good example of the collaborative nature of the I-TEAM effort. Based on experimental needs and differences in expertise, scientists from DOE and CEA worked together to change the level of understanding in the field. These types of interactions are nearly ubiquitous among the tasks in the technical program plan. With the excellence of the team in place and the willingness of the participants to work together for a common understanding, the stated goal of consensus on the mechanistic basis for radionuclide release from glass is well within reach. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Tailored Microstructure and Properties in UO{sub 2}

Advanced fuels with enhanced safety margin and accident tolerance are of vital importance for safe operation of current light water reactor fleet and the development of future reactor systems. The current UO{sub 2} fuel for LWRs has low thermal conductivity, which will be further reduced upon burn-up. The intrinsically low thermal transfer efficiency of the oxide fuels results in a large temperature gradient within the fuel pellet and high center-line temperature. Thermal swelling of the pellets and fission product accommodation and retention limit the lifetime of UO{sub 2} fuel in the reactor, presenting the great challenges for extending burn-up, effective utilization of nuclear resources and minimization of nuclear waste accumulation. Critical needs also exist in developing accident tolerant fuels that can tolerate loss of coolant accident or improve fuel performance under regular operation or beyond design scenario. Key properties of advanced fuels include high thermal conductivity, oxidation resistance, high temperature mechanical properties, fission gas retention capability and thus improved accident tolerance. The US Nuclear Energy Advanced Modeling and Simulation (NEAMS) program is developing science-based next generation fuel performance modeling capability as part its Fuel Product Line in order to facilitate the predictive capability of nuclear fuel performance and assist the design and analysis of reactor systems. Critical experimental data are needed to validate MARMOT models, particularly on effective thermal transport, fracture mechanisms, grain growth kinetics and fission gas behavior. The fabrication of sintered fuel pellets with well-controlled microstructure is prerequisite to establish the correlation of the microstructure features and fuel behavior in order to develop high fidelity fuel performance models. In this talk, recent advancements on developing advanced UO{sub 2} fuels and properties improvement are overviewed with the emphasis on different accident tolerant fuel (ATF) concepts and tailoring microstructures for MARMOT validation. Current efforts on ATFs include composite fuels and high-density fuels to improve thermal-mechanical properties and fission gas retention capabilities. Different composite UO{sub 2} fuels are fabricated with heterogeneous phases as sintering additives for microstructure and property control, and the potential application of the composites as advanced fuels with enhanced accident tolerance will be discussed. In addition, recent progresses of using field-assisted sintering technologies, specifically spark plasma sintering (SPS), in tailoring and engineering fuel matrix as the target systems for validating MARMOT physics models will be highlighted. Particularly, monolithic UO{sub 2} with tailored microstructure including grain size across multiple length scales from nano-metered to micron-sizes, porosity and stoichiometry can be sintered. The impacts of tailored microstructure on thermal-mechanical properties and grain growth kinetics are discussed within the context of the MARMOT modeling. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗