Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

Shock compression behavior of bi-material powder composites with disparate melting temperatures

Laser driven experiments were used to investigate the shock compression behavior of powder processed Bismuth/Tungsten (Bi/W) composite samples. The constituents provide different functionality to the composite behavior as Bi could be shock melted at the pressures attained in this work, while the W could not. Samples were prepared by uniaxial pressing, and the relative density was measured as a function of particle size, applied pressure, and composition for both hot and cold pressing conditions. This resulted in sample densities between 73% and 99% of the theoretical maximum density, and also noticeable differences in microstructure in the hot and cold pressed samples. The compression waves were generated with a 1.3 × 1.3 mm square spot directly onto the surface of the sample, using irradiances between 10{sup 12} and 10{sup 13} W/cm{sup 2}, which resulted in calculated peak pressures between 50 and 150 GPa within a few micrometers. Sample recovery and post-mortem analysis revealed the formation of a crater on the laser drive surface, and the depth of this crater corresponded to the depth to which the Bi had been melted. The melt depth was found to be primarily a function of residual porosity and composition, and ranged from 167 to 528 μm. In general, a higher porosity led to a larger melt depth. Direct numerical simulations were performed, and indicated that the observed increase in melt depth for low-porosity samples could be largely attributed to increased heating associated with work done for pore collapse. However, the relative scaling was sensitive to composition, with low volume fraction Bi samples exhibiting a much stronger dependence on porosity than high Bi content samples. Select samples were repeated using an Al foil ablator, but there were no noticeable differences ensuring that the observed melting was indeed pressure-driven and was not a result of direct laser heating. The resultant microstructures and damage near the spall surface were also investigated qualitatively.

36 MATERIALS SCIENCE↗

Weak Gravitational Lensing around Low Surface Brightness Galaxies in the DES Year 3 Data

We present galaxy-galaxy lensing measurements using a sample of low surface brightness galaxies (LSBGs) drawn from the Dark Energy Survey Year 3 (Y3) data as lenses. LSBGs are diffuse galaxies with a surface brightness dimmer than the ambient night sky. These dark-matter-dominated objects are intriguing due to potentially unusual formation channels that lead to their diffuse stellar component. Given the faintness of LSBGs, using standard observational techniques to characterize their total masses proves challenging. Weak gravitational lensing, which is less sensitive to the stellar component of galaxies, could be a promising avenue to estimate the masses of LSBGs. Our LSBG sample consists of 23,790 galaxies separated into red and blue color types at g - i ≥ 0.60 and g - i < 0.60 , respectively. Combined with the DES Y3 shear catalog, we measure the tangential shear around these LSBGs and find signal-to-noise ratios of 6.67 for the red sample, 2.17 for the blue sample, and 5.30 for the full sample. We use the clustering redshifts method to obtain redshift distributions for the red and blue LSBG samples. Assuming all red LSBGs are satellites, we fit a simple model to the measurements and estimate the host halo mass of these LSBGs to be log(M host /M ⊙ ) = $12.98^{+0.10}_{-0.11}$. We place a 95% upper bound on the subhalo mass at log(M sub /M ⊙ ) < 11.51. By contrast, we assume the blue LSBGs are centrals, and place a 95% upper bound on the halo mass at log(M host /M ⊙ ) < 11.84. We find that the stellar-to-halo mass ratio of the LSBG samples is consistent with that of the general galaxy population. This work illustrates the viability of using weak gravitational lensing to constrain the halo masses of LSBGs.

79 ASTRONOMY AND ASTROPHYSICS↗

Warm dust around cool stars: field M dwarfs with Wise 12 or 22 μm excess emission

Using the Sloan Digital Sky Survey Data Release 7 (SDSS DR7) spectroscopic catalog, we searched the WISE AllWISE catalog to investigate the occurrence of warm dust, as inferred from IR excesses, around field M dwarfs (dMs). We developed SDSS/WISE color selection criteria to identify 175 dMs (from 70,841) that show IR flux greater than the typical dM photosphere levels at 12 and/or 22 μm, including seven new stars within the Orion OB1 footprint. We characterize the dust populations inferred from each IR excess and investigate the possibility that these excesses could arise from ultracool binary companions by modeling combined spectral energy distributions. Our observed IR fluxes are greater than levels expected from ultracool companions (>3σ). We also estimate that the probability the observed IR excesses are due to chance alignments with extragalactic sources is <0.1%. Using SDSS spectra we measure surface gravity-dependent features (K, Na, and CaH 3) and find <15% of our sample indicates low surface gravities. Examining tracers of youth (Hα, UV fluxes, and Li absorption), we find <3% of our sample appear young, indicating we are observing a population of field stars ≳1 Gyr, likely harboring circumstellar material. We investigate age-dependent properties probed by this sample, studying the disk fraction as a function of Galactic height. The fraction remains small and constant to |Z| ∼ 700 pc and then drops, indicating little to no trend with age. Possible explanations for disks around field dMs include (1) collisions of planetary bodies, (2) tidal disruption of planetary bodies, or (3) failed planet formation.

79 ASTRONOMY AND ASTROPHYSICS↗

Ultrasound-assisted facile synthesis of a new tantalum(V) metal-organic framework nanostructure: Design, characterization, systematic study, and CO{sub 2} adsorption performance

This work presents a fast route for the preparation of a new Ta(V) metal-organic framework nanostructure with high surface area, significant porosity, and small size distribution. X-ray diffraction (XRD), scanning electron microscopy (SEM), Transition electron microscopy (TEM), energy dispersive spectrometer (EDS), thermo-gravimetric analysis (TGA), differential scanning calorimetry (DSC), fourier transform infrared spectroscopy (FTIR), CHNS/O elemental analyser, and Brunauer-Emmett-Teller (BET) surface area analysis were applied to characterize the synthesized product. Moreover, the influences of ultrasonic irradiation including temperature, time, and power on different features of the final products were systematically studied using 2{sup k-1} factorial design experiments, and the response surface optimization was used for determining the best welding parameter combination. The results obtained from analyses of variances showed that ultrasonic parameters affected the size distribution, thermal behaviour, and surface area of Ta-MOF samples. Based on response surface methodology, Ta-MOF could be obtained with mean diameter of 55 nm, thermal stability of 228 °C, and high surface area of 2100 m{sup 2}/g. The results revealed that the synthesized products could be utilized in various applications such as a novel candidate for CO{sub 2} adsorption. - Graphical abstract: A facile route was used for fabrication of a new metal -organic framework based on tantalum nanostructures that have high surface area, considerable porosity, homogenous morphology, and small size distribution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ferroic phase transitions and magnetoelectric coupling in cobalt doped BaTiO 3

Magnetoelectric (ME) materials exhibit interesting physics with cross coupling between ferroelectric and magnetic order parameters and thus strong potential to be utilized in memory, spintronics and other multifunctional electronic/magnetic devices. Doping of suitable transition metals in ferroelectrics can induce magnetism and ME coupling and modify the physical properties. Here, we report the structural, electronic, magnetic and ME coupling of 3.5, 5 and 7.5 mol% cobalt doped BaTiO 3 (BTO) ceramics. X-ray diffraction and Raman spectroscopy indicate that the samples are single phase having a tetragonal crystal structure with P4mm symmetry. The tetragonality ratio is found to decrease with increasing cobalt content. We observed a Fano-like asymmetric peak in the [A 1 (LO 1 )] Raman mode at ~173 cm -1 in all the cobalt doped BTO samples. The cobalt dopants are shown to be uniformly distributed throughout the surface of the samples. We observed a lowering of the ferroelectric transition temperature and increasing diffusivity parameter with increasing cobalt concentration. The electrical properties of all the samples have been investigated in detail by impedance spectroscopy and ac conductivity studies before and after the ferroelectric phase transitions. All the samples show hysteretic ferroelectric behavior with a clear saturation state that decreases with increasing cobalt content. The observed ferroelectricity in these samples is intrinsic in nature. The 3.5% cobalt doped BTO sample exhibits paramagnetic behavior whereas the 5 and 7.5% cobalt doped BTO samples show ferromagnetic ordering below 43 K. The 7.5% cobalt doped BTO samples show significant ME coupling.

36 MATERIALS SCIENCE↗

Cluster size effects on sintering, CO adsorption, and implantation in Ir/SiO{sub 2}

A series of planar model catalysts have been prepared via deposition of Ir{sub n}{sup +} on thermally grown amorphous SiO{sub 2}/Si(100) and ion scattering spectroscopy was used to probe surface structure as a function of cluster size, impact energy, and surface temperature. Deposition of Ir{sub 2} or Ir{sub 10} at low energies and room temperature results in stable clusters forming one- or two-dimensional single layer islands on the oxide surface. Heating the samples to 750 K leads to agglomeration, forming multilayer structures on the surface. Ir{sub 1} deposited under similar conditions sinters into large clusters at room temperature. Deposition at 110 K at least partially stabilizes the Ir atoms with respect to diffusion and sintering. At higher deposition energies, partial implantation into the surface is observed, but this appears to be insufficient to stabilize the clusters against sintering at elevated temperature. At low temperatures, substrate-mediated adsorption of CO is found to be highly efficient, leading to near saturation coverages of CO bound atop the Ir{sub n} clusters. The CO can be removed by careful He{sup +} sputtering. The deposition/binding behavior of Ir{sub n} on SiO{sub 2} is quite different from Ir{sub n}/TiO{sub 2}(110), for which the clusters bind in three-dimensional morphology, starting at Ir{sub 5}. That system also shows substrate-mediated adsorption of CO, but the CO preferentially binds at the periphery of the clusters rather than on top.

36 MATERIALS SCIENCE↗

A versatile elevated-pressure reactor combined with an ultrahigh vacuum surface setup for efficient testing of model and powder catalysts under clean gas-phase conditions

A small-volume reaction cell for catalytic or photocatalytic testing of solid materials at pressures up to 1000 Torr has been coupled to a surface-science setup used for standard sample preparation and characterization under ultrahigh vacuum (UHV). The reactor and sample holder designs allow easy sample transfer from/to the UHV chamber, and investigation of both planar and small amounts of powder catalysts under the same conditions. The sample is heated with an infrared laser beam and its temperature is measured with a compact pyrometer. Combined in a regulation loop, this system ensures fast and accurate temperature control as well as clean heating. The reaction products are automatically sampled and analyzed by mass spectrometry and/or gas chromatography (GC). Unlike previous systems, our GC apparatus does not use a recirculation loop and allows working in clean conditions at pressures as low as 1 Torr while detecting partial pressures smaller than 10{sup −4} Torr. The efficiency and versatility of the reactor are demonstrated in the study of two catalytic systems: butadiene hydrogenation on Pd(100) and CO oxidation over an AuRh/TiO{sub 2} powder catalyst.

36 MATERIALS SCIENCE↗

Directional Cooling-Induced Fracturing Westerly Granite Test Results

Directional Cooling-Induced Fracturing (DCIF) experiments were conducted on a short, cylindrical sample of Westerly granite (diameter = 4 inches, height ~ 2 inches). Liquid nitrogen was poured in a copper cup attached to the top of the sample, and the resulting acoustic emissions (AEs) and temperature changes on the surface of the sample were monitored. The obtained AEs were used to determine the microcracking source locations and amplitude, and the associated moment tensors. Included in this submission is an animation of the AEs, a graphic displaying the temperature changes, and the measured data.

15 GEOTHERMAL ENERGY↗

DCIF Westerly Granite AE Stress Effect Test (Task 3-1)

Directional Cooling-Induced Fracturing (DCIF) experiments were conducted on rectangular Westerly granite blocks (width=depth=4.0", height=2.0"). Liquid nitrogen was poured in a small, 1"-diameter copper cup attached to the top of the sample, and the resulting acoustic emissions (AEs) and temperature changes on the surface of the sample were monitored. Several confining stresses were applied bi-axially to the sides of the samples so that the onset of AE activity and the stress applied to the sample were correlated. The obtained AEs were used to determine the microcracking source locations and amplitude, and the associated moment tensors. Included in this submission are the animations of the AE locations and graphics displaying the measured temperature-AE activity changes for different stresses.

15 GEOTHERMAL ENERGY↗

DCIF (Directional Cooling-Induced Fracturing) Westerly Granite AE Borehole Damage Effect Test (Task 3-0)

Directional Cooling-Induced Fracturing (DCIF) experiments were conducted on three rectangular Westerly granite blocks (width=depth=4.0", height=2.0") which were preheated to 200, 400, and 600 degree C to induce damage (microcracks) with varying degrees. Liquid nitrogen was poured in a small, 1"-diameter copper cup attached to the top of the sample, and the resulting acoustic emissions (AEs) and temperature changes on the surface of the sample were monitored. The experiments were conducted under one selected biaxial stress (5.8MPa). The obtained AEs were used to determine the microcracking source locations and amplitude, and the associated moment tensors. The onset time of the AEs was correlated with the cooling temperature, which was used to show that the temperature at the onset of microcracking is not affected significantly by the preexisting damage, compared to the impact of the stress in the sample. Included in this submission are the animations of the AE locations and graphics displaying the measured temperature-AE activity changes for samples with different degrees of microcrack damage.

15 GEOTHERMAL ENERGY↗

Streamlined Approach for Environmental Restoration (SAFER) Plan for Corrective Action Unit 544: Cellars, Mud Pits, and Oil Spills, Nevada Test Site, Nevada, Revision 0

This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the actions needed to achieve closure for Corrective Action Unit (CAU) 544, Cellars, Mud Pits, and Oil Spills, identified in the Federal Facility Agreement and Consent Order (FFACO). Corrective Action Unit 544 comprises the following 20 corrective action sites (CASs) located in Areas 2, 7, 9, 10, 12, 19, and 20 of the Nevada Test Site (NTS): • 02-37-08, Cellar & Mud Pit • 02-37-09, Cellar & Mud Pit • 07-09-01, Mud Pit • 09-09-46, U-9itsx20 PS #1A Mud Pit • 10-09-01, Mud Pit • 12-09-03, Mud Pit • 19-09-01, Mud Pits (2) • 19-09-03, Mud Pit • 19-09-04, Mud Pit • 19-25-01, Oil Spill • 19-99-06, Waste Spill • 20-09-01, Mud Pits (2) • 20-09-02, Mud Pit • 20-09-03, Mud Pit • 20-09-04, Mud Pits (2) • 20-09-06, Mud Pit • 20-09-07, Mud Pit • 20-09-10, Mud Pit • 20-25-04, Oil Spills • 20-25-05, Oil Spills This plan provides the methodology for field activities needed to gather the necessary information for closing each CAS. There is sufficient information and process knowledge from historical documentation and investigations of similar sites regarding the expected nature and extent of potential contaminants to recommend closure of CAU 544 using the SAFER process. Using the approach approved for previous mud pit investigations (CAUs 530–535), 14 mud pits have been identified that • are either a single mud pit or a system of mud pits, • are not located in a radiologically posted area, and • have no evident biasing factors based on visual inspections. These 14 mud pits are recommended for no further action (NFA), and further field investigations will not be conducted. For the sites that do not meet the previously approved closure criteria, additional information will be obtained by conducting a field investigation before selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible recommendation for closure of the remaining CASs in CAU 544. This will be presented in a closure report (CR) that will be prepared and submitted to the Nevada Division of Environmental Protection (NDEP) for review and approval. The sites will be investigated based on the data quality objectives (DQOs) developed on April 27, 2010, by representatives of NDEP and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO). The DQO process was used to identify and define the type, amount, and quality of data needed to determine and implement appropriate corrective actions for each CAS in CAU 544. The DQO process developed for this CAU identified the following expected closure options: (1) investigation and confirmation that no contamination exists above the final action levels (FALs) leading to an NFA declaration, (2) characterization of the nature and extent of contamination leading to closure in place with use restrictions, (3) clean closure by remediation and verification, (4) closure in place with use restrictions with no investigation if CASs are in crater areas that have been determined to be unsafe to enter, or (5) NFA if the mud pit CAS meets the criteria established during the CAUs 530–535 SAFER investigation. The following summarizes the SAFER activities that will support the closure of CAU 544: • Perform visual inspection of all CASs. • Perform site preparation activities (e.g., utilities clearances, construction of temporary site exclusion zones). • Removal of easily managed, nonhazardous, and nonradioactive debris, including vegetation (e.g., tumbleweeds), at various CASs that interfere with sampling, if required to inspect soil surface or collect soil sample. • Collect environmental samples from designated target populations (e.g., mud pits, cellars, stained soil) to confirm or disprove the presence of contaminants of concern (COCs) as necessary to supplement existing information. • If no COCs are present at a CAS, establish NFA as the corrective action. • If COCs exist, collect environmental samples from designated target populations (e.g., clean soil adjacent to contaminated soil) and submit for laboratory analyses to define the extent of COC contamination. • If a COC is present at a CAS, either - Establish clean closure as the corrective action. The material to be remediated will be removed, disposed of as waste, and verification samples will be collected from remaining soil, or - Establish closure in place as the corrective action and implement the appropriate use restrictions. • Confirm the preferred closure option is sufficient to protect human health and the environment.

01 COAL, LIGNITE, AND PEAT↗

Preparing rock powder specimens of controlled size distribution

Apparatus produces rock powder specimens of the size distribution needed in geological sampling. By cutting grooves in the surface of the rock sample and then by milling these shallow, parallel ridges, the powder specimen is produced. Particle size distribution is controlled by changing the height and width of ridges.

Blum, P.↗

Investigations of lunar materials

In the particle track work, a series of dating techniques for learning about the surface history of soil and rock samples was developed. The surface behavior and history of diverse lunar rocks and soils, erosion rates, and deposition rates were studied, along with incident heavy cosmic ray spectrum.

Fleischer, R. L.↗

Short guide to lunar sample information

Data pertaining to the collection, processing, and study of lunar samples, and the ways to gain access to that data are described. Data pertaining to the samples includes not only the normally published literature but also NASA and USGS interagency documents, sample processing information, and photography taken from lunar orbit, on the lunar surface, and of samples in the Lunar Receiving Laboratory.

Simonds, C. H.↗

A method for the evaluation of damage on the surface of carbon-carbon ablation samples

The effect of weave geometry on the onset of transition from laminar to turbulent flow around a sample of an orthogonally woven fine weave carbon-carbon material tested in an arc-jet is investigated. Seventeen post-test models which had undergone only partial transition around the circumference were examined as to location of turbulent regions relative to the weave axes. It was statistically shown that the weave axes had the lowest probability of being a position of initial transition onset. The probability generally increased with distance from a major axis, with some rays, notably the 45 deg rays, showing better transition resistance than the adjacent rays. The incidence of initial transition onset correlated well with the number of X or Y fibers that the flow passes over from stagnation point to the shoulder.

Heinonen, E. W.↗

ESCA studies of lunar surface chemistry

We have used ESCA to compare the composition of the natural exterior surface in lunar fines samples with that of the interior surface exposed by crushing. Even though the exterior surfaces have been exposed to air a significant amount of Fe in them is reduced. In addition, Ca, Al, and Mg are strongly depleted in exterior surfaces relative to Si, Ti, and Fe. Preferential sputtering by the solar wind is a possible explanation for these changes.

Housley, R. M.↗