Structural and compositional analysis of solid oxide fuel cell electrolytes using transmission electron microscopy
Explore the source record for details and available documents.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
During thermal annealing at 1425 °C nominal electric field strengths of 50 V/mm and 150 V/mm were applied along the grain boundary planes of a near 45° (100) twist grain boundary in SrTiO 3 . Electron microscopy characterization revealed interface expansions near the positive electrode around 0.8 nm for either field strength. While the interface width decreased to roughly 0.4 nm after annealing at 50 V/mm, the higher field strength caused decomposition of the boundary structure close to the negative electrode. Electron energy-loss and X-ray photoelectron spectroscopies demonstrated an increased degree of oxygen sublattice distortion at the negative electrode side, and enhanced concentrations of Ti 3+ and Ti 2+ compared to bulk for both single crystals and bicrystals annealed with an external electric field, respectively. Oxygen migration due to the applied electric field causes the observed alteration of grain boundary structures. At sufficiently high field strength the agglomeration of anion vacancies may lead to the decomposition of the grain boundary.
Oxygen-deficient TiO{sub 2} films with enhanced visible and near-infrared optical absorption have been deposited by reactive sputtering using a planar diode radio frequency magnetron configuration. It is observed that the increase in the absorption coefficient is more effective when the O{sub 2} gas supply is periodically interrupted rather than by a decrease of the partial O{sub 2} gas pressure in the deposition plasma. The optical absorption coefficient at 1.5 eV increases from about 1 Multiplication-Sign 10{sup 2} cm{sup -1} to more than 4 Multiplication-Sign 10{sup 3} cm{sup -1} as a result of the gas flow discontinuity. A red-shift of {approx}0.24 eV in the optical absorption edge is also observed. High resolution transmission electron microscopy with composition analysis shows that the films present a dense columnar morphology, with estimated mean column width of 40 nm. Moreover, the interruptions of the O{sub 2} gas flow do not produce detectable variations in the film composition along its growing direction. X-ray diffraction and micro-Raman experiments indicate the presence of the TiO{sub 2} anatase, rutile, and brookite phases. The anatase phase is dominant, with a slight increment of the rutile and brookite phases in films deposited under discontinued O{sub 2} gas flow. The increase of optical absorption in the visible and near-infrared regions has been attributed to a high density of defects in the TiO{sub 2} films, which is consistent with density functional theory calculations that place oxygen-related vacancy states in the upper third of the optical bandgap. The electronic structure calculation results, along with the adopted deposition method and experimental data, have been used to propose a mechanism to explain the formation of the observed oxygen-related defects in TiO{sub 2} thin films. The observed increase in sub-bandgap absorption and the modeling of the corresponding changes in the electronic structure are potentially useful concerning the optimization of efficiency of the photocatalytic activity and the magnetic doping of TiO{sub 2} films.
This work reports heavy ion-irradiation effects in polycrystalline Fe 3 O 4 . For this matter, Fe/Fe 3 O 4 heterostructures were irradiated in situ in a transmission electron microscopy with 1 MeV Kr ions at 50 K. Evidence of cubic to monoclinic transformation (a.k.a Verwey transition) was recorded in some magnetite grains upon cooling the sample (around 90 K); however, most of the oxide grains retain their cubic spinel structure. Irradiation effects were analyzed in the cubic phase up to a maximum dose of 38 dpa without the sign of amorphization. The extinction of first-order reflections was recorded at doses below 1 dpa, indicating the formation of a new (metastable) phase with half of the lattice parameters compared to the unirradiated Fe 3 O 4 crystal. The formation of the new crystalline phase, which also presents a high resistance to amorphization, is related to the disordering of the cation lattice and the high mobility of the cation interstitials. The metastable phase readily recovers around 225 K during the natural warming of the sample from 50 K to room temperature.
Structures of nanoparticles in Fe-16Cr-4.5Al-0.3Ti-2W-0.37Y2O3 (K3) and Fe-20Cr-4.5Al-0.34Ti-0.5Y2O3 (MA956) oxide dispersion strengthened (ODS) ferritic steels produced by mechanical alloying (MA) and followed by hot extrusion have been studied using high-resolution transmission electron microscopy (HRTEM) techniques to gain insight about the formation mechanism of nanoparticles in MA/ODS steels. The observations of Y-Al-O complex-oxide nanoparticles in both ODS steels imply that decomposition of Y2O3 in association with internal oxidation of Al occurred during mechanical alloying. While the majority of oxide nanoparticles formed in both steels is Y4Al2O9, a few oxide particles of YAlO3 are also occasionally observed. These results reveal that Ti (0.3 wt %) plays an insignificant role in forming oxide nanoparticles in the presence of Al (4.5 wt %). HRTEM observations of crystalline nanoparticles larger than ~2 nm and amorphous or disordered cluster domains smaller than ~2 nm provide an insight into the formation mechanism of oxide nanoparticle in MA/ODS steels, which we believe from our observations involves a solid-state amorphous precursor followed by recrystallization. Dual ion-beam irradiations using He + +Fe +8 ions were employed to gain more detailed insight about the role of nanoparticles in suppressing radiation-induced swelling. This is elaborated through TEM examinations of cavity distributions in ion-irradiated Fe-14Cr and K3-ODS ferritic steels. HRTEM observations of helium-filled cavities (helium bubbles) preferably trapped at nanoscale oxide particles and clusters in ion-irradiated K3-ODS are presented. Finally, we describe the results from triple ion-beam irradiations using He + +Fe +8 ions to emulate fusion first wall radiation effects. Preliminary work is reported that confirms the existence of significant hydrogen synergistic effects described earlier by Tanaka et al., for Fe(Cr) and by Wakai et al., for F82H reduced activation ferritic martensitic (RAF/M) steel. These previous results combined with our data suggest a complex new 'catalytic' mechanism whereby H interacts with the steady state population of defects and the embryonic cavities so as to accelerated cavity (void) growth in both Fe(Cr) and under special conditions in ODS steels.
Mn-doped BiFeO{sub 3} films with Mn contents of 5 and 10 mol. % were prepared via a chemical route. A carefully controlled amount of Bi deficiency was introduced to further tune the lattice structure and the functionality of multiferroic BiFeO{sub 3}. The crystal structure of Bi{sub 1−δ}Fe{sub 1−x}Mn{sub x}O{sub 3} films was investigated by X-ray diffraction and Raman spectra; a rhombohedral-to-orthorhombic phase transition was revealed. The observed double hysteresis loops and two capacitance maxima from polarization vs electric field and capacitance-voltage measurements indicate an antiferroelectric-like behavior. Additionally, the coexistence of ferroelectric (FE) and antiferroelectric (AFE) phases in Bi{sub 1−δ}Fe{sub 1−x}Mn{sub x}O{sub 3} films was revealed from the domain structures obtained by piezoelectric force microscopy. The effects of Mn substitution in conjunction with Bi deficiency on the FE-AFE phase transition and electrical behavior of BiFeO{sub 3} films are discussed in detail. Meanwhile, magnetic and photoluminescence measurements on the films illustrate that Mn substitution gives rise to the net magnetic moment and the defects induced by both Bi deficiency and Mn substitution influence the electronic structure of BiFeO{sub 3} films. This study thus shows a simple and effective way to control the functionalities of BiFeO{sub 3} films.
The pyrochlore oxides (A{sub 2}B{sub 2}O{sub 7}) exhibit a remarkable range of structural, physical, and magnetic properties related to their various chemical compositions. This article reports the phase transformations induced by high electronic excitation in pyrochlores of the Gd{sub 2}(Zr{sub x}Ti{sub 1-x}){sub 2}O{sub 7} family irradiated with swift ions. The structural changes, investigated by using several analytical techniques (x-ray diffraction, Raman spectroscopy, and transmission electron microscopy), strongly depend on the chemical composition. The high electronic excitation along the ion trajectory results in the amorphization of ion tracks for Gd{sub 2}Ti{sub 2}O{sub 7} and Gd{sub 2}TiZrO{sub 7}, whereas a defective fluorite structure is formed in Gd{sub 2}Zr{sub 2}O{sub 7}. Moreover, the results underline the existence of an electronic stopping power threshold of 6 keV/nm for amorphizable compounds and 10 keV/nm for Gd{sub 2}Zr{sub 2}O{sub 7}, below which phase transformations do not occur. Finally, the study of the thermal recovery of irradiated pyrochlores provides the recrystallization temperature for amorphized samples and reveals differences in the recovery process which are related to the chemical composition.
The halide perovskite formamidinium lead iodide (FAPbI 3 ) is a prime candidate for photovoltaics due to its excellent optoelectronic properties, but its application has been limited due to its structural instability. The large size of the FA cation results in metastability of the photoactive cubic phase and a facile degradation into thermodynamically stable hexagonal phases at room temperature. Recently, the incorporation of two-dimensional (2D) Ruddlesden-Popper halide perovskite seeds into a FAPbI 3 precursor solution was shown to template the growth of and stabilize cubic FAPbI 3 . Here, in this study, we investigate the nanoscale structural and optoelectronic mechanisms behind the observed bulk stabilization using synchrotron-based X-ray microscopies. Nanoprobe X-ray diffraction reveals 2D-templated FAPbI 3 films exhibit an average compressive strain normal to the substrate of -3.3%, 2-fold larger than that of MACl-stabilized FAPbI 3 . This compression creates locally templated regions composed of tetragonal-phase FAPbI 3 distributed nonuniformly throughout the film with fewer crystalline defects than purely cubic regions. Scanning X-ray excited optical luminescence (X-ray analog of photoluminescence) reveals that this local templating results in increased radiative recombination and red-shifted band edge and emission. Our results provide insight into the microscopic mechanism for the phase stabilization of FAPbI 3 using 2D perovskites as templates.
This interim report presents progress towards the development of meso-scale models of magnetic behavior that incorporate microstructural information. Modeling magnetic signatures in irradiated materials with complex microstructures (such as structural steels) is a significant challenge. The complexity is addressed incrementally, using the monocrystalline Fe (i.e., ferrite) film as model systems to develop and validate initial models, followed by polycrystalline Fe films, and by more complicated and representative alloys. In addition, the modeling incrementally addresses inclusion of other major phases (e.g., martensite, austenite), minor magnetic phases (e.g., carbides, FeCr precipitates), and minor nonmagnetic phases (e.g., Cu precipitates, voids). The focus of the magnetic modeling is on phase-field models. The models are based on the numerical solution to the Landau-Lifshitz-Gilbert equation. From the computational standpoint, phase-field modeling allows the simulation of large enough systems that relevant defect structures and their effects on functional properties like magnetism can be simulated. To date, two phase-field models have been generated in support of this work. First, a bulk iron model with periodic boundary conditions was generated as a proof-of-concept to investigate major loop effects of single versus polycrystalline bulk iron and effects of single non-magnetic defects. More recently, to support the experimental program herein using iron thin films, a new model was generated that uses finite boundary conditions representing surfaces and edges. This model has provided key insights into the domain structures observed in magnetic force microscopy (MFM) measurements. Simulation results for single crystal thin-film iron indicate the feasibility of the model for determining magnetic domain wall thickness and mobility in an externally applied field. Because the phase-field model dimensions are limited relative to the size of most specimens used in experiments, special experimental methods were devised to create similar boundary conditions in the iron films. Preliminary MFM studies conducted on single and polycrystalline iron films with small sub-areas created with focused ion beam have correlated quite well qualitatively with phase-field simulations. However, phase-field model dimensions are still small relative to experiments thus far. We are in the process of increasing the size of the models and decreasing specimen size so both have identical dimensions. Ongoing research is focused on validation of the phase-field model. Validation is being accomplished through comparison with experimentally obtained MFM images (in progress), and planned measurements of major hysteresis loops and first order reversal curves. Extrapolation of simulation sizes to represent a more stochastic bulk-like system will require sampling of various simulations (i.e., with single non-magnetic defect, single magnetic defect, single grain boundary, single dislocation, etc.) with distributions of input parameters. These outputs can then be compared to laboratory magnetic measurements and ultimately to simulate magnetic Barkhausen noise signals.
Understanding how materials evolve during synthesis, processing, or device operation requires experimental access to structural dynamics across wide ranges of length and time scales, often in bulk samples or even within packaged devices. Time-resolved full-field diffraction X-ray microscopy has recently emerged as a powerful way to meet this need by combining the penetration and structural sensitivity of X-ray diffraction with objective-lens-based magnification, sensitive high-resolution X-ray imaging detectors, and pump-probe and real-time imaging strategies. Advances in full-field X-ray diffraction microscopy, often termed dark-field X-ray microscopy (DFXM), enable simultaneous imaging of extended fields of view while retaining crystallographic selectivity. Time-resolved DFXM promises to enable advances in materials processing and dynamics, electrochemical and photochemical processes, and the design of electronic devices. This Perspective summarizes the key instrumental concepts that define the performance of these methods, including the choice of imaging optics, detector considerations, and the impact of source time structure at synchrotron light sources and X-ray free-electron lasers (XFELs). We discuss the simultaneous use of complementary imaging modes that are increasingly used in practice. The early demonstrations of the potential of time-resolved DFXM include real-time defect and grain-boundary dynamics during metal annealing, stroboscopic imaging of functional devices with high strain sensitivity, and ultrafast pump-probe implementations at XFELs that directly visualize acoustic-wave propagation and energy dissipation in bulk crystals.
ZnO nanorods were grown by chemical bath deposition on sputtered, polycrystalline GaN buffer layers with and without ZnO seed layer. Scanning electron microscopy and X-ray diffraction show that the ZnO nanorods on GaN buffer layers are not vertically well aligned. Photoluminescence spectrum of ZnO nanorods grown on GaN buffer layer, however exhibits a much stronger near-band-edge emission and negligible defect emission, compared to the nanorods grown on ZnO buffer layer. These features are attributed to gallium incorporation at the ZnO-GaN interface. The introduction of a thin (25 nm) ZnO seed layer on GaN buffer layer significantly improves the morphology and vertical alignment of ZnO-NRs without sacrificing the high optical quality of ZnO nanorods on GaN buffer layer. The presence of a thick (200 nm) ZnO seed layer completely masks the effect of the underlying GaN buffer layer on the morphology and optical properties of nanorods.
Wurtzite InN films were prepared on a 6H-SiC substrate by a self-designed plasma-assisted metal-organic molecular-beam epitaxy system without a buffer layer. In this article, the authors investigate the structural and optical properties of InN films grown on a 6H-SiC substrate. The crystallinity and microstructure of the thin film were further characterized by x-ray diffraction (XRD), field-emission scanning-electron microscopy, and transmission-electron microscopy. Electrical and optical properties were evaluated by Hall and photoluminescence (PL) measurements. XRD results indicate that InN film grown at 500 deg. C is epitaxially grown along the c-axis orientation. The two-dimensional growth mode is clearly shown in scanning-electron microscope images. Room-temperature PL spectra show that the emission peak is located at {approx}0.83 eV due to the Burstein-Moss effect. In addition, the crystalline InN samples crack and peel away from the substrate at elevated growth temperature. This phenomenon may be attributed to lattice mismatch and grain coalescence while increasing the growth temperature. The narrow window of the growth temperature plays an important role in engineering the InN epitaxial growth.
Metal–Organic Frameworks (MOFs) have the potential to change the landscape of molecular separations in chemical processes owing to their ability of selectively binding molecules. Their molecular sorting properties generally rely on the micro- and meso-pore structure, as well as on the presence of coordinatively unsaturated sites that interact with the different chemical species present in the feed. In this work, we show a first-of-its-kind tomographic imaging of the crystal morphology of a metal– organic framework by means of transmission X-ray microscopy (TXM), including a detailed data reconstruction and processing approach. Corroboration with Focused Ion Beam-Scanning Electron Microscopy (FIB-SEM) images shows the potential of this strategy for further (non-destructively) assessing the inner architecture of MOF crystals. By doing this, we have unraveled the presence of large voids in the internal structure of a MIL-47(V) crystal, which are typically thought of as rather homogeneous lattices. This challenges the established opinion that hydrothermal syntheses yield relatively defect-free material and sheds further light on the internal morphology of crystals.
Graphical abstract: - Highlights: • α-Ti to β-Ti phase conversion is observed during 1 h of milling. • Ti{sub 0.7}Ni{sub 0.3}N (fcc) phase is noticed to form after 1 h of milling. • Formation time of Ti(Ni,N) phase is same as TiN phase. • Both X-ray and HRTEM microstructure characterization revealed similar results. - Abstract: Nanocrystalline stoichiometric Ti{sub 0.7}Ni{sub 0.3}N powder has been synthesized by ball-milling the α-Ti (hcp) and Ni (fcc) powders under N{sub 2} gas at room temperature. The α-Ti phase partially transforms to the transient (-Ti phase after 1 h of milling. After 5.5 h of milling, very broad reflections of Ti{sub 0.7}Ni{sub 0.3}N phase is noticed. Complete formation of Ti{sub 0.7}Ni{sub 0.3}N phase is observed after 9 h of milling. Microstructure in terms of lattice imperfections of unmilled and all ball-milled powder mixtures are primarily characterized by analyzing the X-ray powder diffraction patterns employing the Rietveld structure refinement procedure. It clearly reveals the presence of Ti{sub 0.7}Ni{sub 0.3}N phase and inclusion of nitrogen atoms into the α-Ti–Ni matrix on the way to formation of nitride phase. Microstructure of the ball milled nitride powders is also characterized by HRTEM. Particle size of Ti{sub 0.7}Ni{sub 0.3}N phase obtained from XRD method of characterization is ∼5 nm which is very close to that obtained from HRTEM.
Graphical abstract: Systematic scheme for photocatalytic activity. Pristine and air quenched ZnO nanoparticles were effectively synthesized by simple combustion method and effectively used as photocatalyst for photodegradtion of methyl orange dye. It was observed that air quenched ZnO nanoparticles shows the better properties as compared to pristine ZnO. The complete degradation of dye was observed in 150 min. - Highlights: • Pristine and air quenched ZnO nanoparticles were synthesized by simple combustion method. • Synthesized ZnO for air quenched ZnO has better optoelectronic properties. • ZnO nanoparticles for air quenched ZnO exhibiting complete photodegradation of Methyl Orange dye under UV irradiation. • Photocatalytic activities for all the samples were observed in 150 min. - Abstract: Tuning of defect levels is the major concern for the application of ZnO nanoparticles. These nanoparticles with different defect concentration were prepared by simple combustion method at 700 °C and subsequent quenching in air. The catalyst was characterized by X-Ray Diffraction (XRD), Field Emission Scanning Electron Microscope (FESEM), UV–vis spectroscopy measurements. XRD reveals that the cell volume increased with large temperature difference between 700 °C and quenched media. FTIR confirmed that the vibrational frequencies shifted from 519 cm{sup −1} to 535 cm{sup −1} point out the role of quenching defects. FESEM shows the size is of the order of 20–45 nm and found irregular distribution of grain boundaries in the quenched induced defects. Different morphology plays a major role in the enhancement of photocatalytic efficiency of synthesized nanoparticles. PL intensity indicates more oxygen vacancies for air quenched ZnO whereas; DTA study demonstrates that the synthesized ZnO is thermally stable. Kinetics study confirmed the photodegradation of methyl orange (MO) dye using this photocatalyst follows first order rate constant. It exhibits the complete degradation of dye only in 150 min under UV irradiation. Kinetic study revealed the rate constant of nanoparticles is 0.0165 min{sup −1}. Air quenched sample showed the higher intensity of defect band as compared to pristine ZnO.
Protoapigenone is a unique flavonoid and enriched in many ferns, showing potent antitumor activity against a broad spectrum of human cancer cell lines. RY10-4, a modified version of protoapigenone, manifested better anti-proliferation activity in human breast cancer cell line MCF-7. The cytotoxicity of RY10-4 against MCF-7 cells is exhibited in both time- and concentration-dependent manners. Here we investigated a novel effect of RY10-4 mediated autophagy in autophagy defect MCF-7 cells. Employing immunofluorescence assay for microtubule-associated protein light-chain 3 (LC3), monodansylcadaverine staining, Western blotting analyses for LC3 and p62 as well as ultrastructural analysis by transmission electron microscopy, we showed that RY10-4 induced autophagy in MCF-7 cells but protoapigenone did not. Meanwhile, inhibition of autophagy by pharmacological and genetic approaches significantly increased the viability of RY10-4 treated cells, suggesting that the autophagy induced by RY10-4 played as a promotion mechanism for cell death. Further studies revealed that RY10-4 suppressed the activation of mTOR and p70S6K via the Akt/mTOR pathway. Our results provided new insights for the mechanism of RY10-4 induced cell death and the cause of RY10-4 showing better antitumor activity than protoapigenone, and supported further evidences for RY10-4 as a lead to design a promising antitumor agent. - Highlights: • We showed that RY10-4 induced autophagy in MCF-7 cells but protoapigenone did not. • Autophagy induced by RY10-4 played as a promotion mechanism for cell death. • RY10-4 induced autophagy in MCF-7 cell through the Akt/mTOR pathway. • We provided new insights for the mechanism of RY10-4 induced cell death.
Eukaryotic cells internalize cargo at the plasma membrane via endocytosis, a vital process that is accomplished through a complex network of endosomal organelles. In mammalian cells, the ER is in close association with endosomes and regulates their fission. Nonetheless, the physiological role of such interaction on endocytosis is yet unexplored. Here, we probed the existence of ER–endosome association in plant cells and assayed its physiological role in endocytosis. Through live-cell imaging and electron microscopy studies, we established that endosomes are extensively associated with the plant ER, supporting conservation of interaction between heterotypic organelles in evolutionarily distant kingdoms. Furthermore, by analyzing ER–endosome dynamics in genetic backgrounds with defects in ER structure and movement, we also established that the ER network integrity is necessary for homeostasis of the distribution and streaming of various endosome populations as well as for efficient endocytosis. These results support a novel model that endocytosis homeostasis depends on a spatiotemporal control of the endosome dynamics dictated by the ER membrane network.
Water-soluble sacrificial layers based on epitaxially-grown, single crystalline (Ca, Sr, Ba) 3 Al 2 O 6 layer are widely used for creating free-standing perovskite oxide membranes. However, obtaining these sacrificial layers with intricate stoichiometry remains a challenge, especially for molecular beam epitaxy (MBE). In this study, we demonstrate the hybrid MBE growth of epitaxial, single crystalline SrTiO 3 films using a solution processed, amorphous SrCa 2 Al 2 O 6 sacrificial layer onto SrTiO 3 (001) substrates. Prior to the growth, the oxygen plasma exposure was used to first create the crystalline SrCa 2 Al 2 O 6 layer with well-defined surface crystallinity. Utilizing reflection high energy electron diffraction, x-ray diffraction, and atomic force microscopy, we observe an atomic layer-by-layer growth of epitaxial, single crystalline SrTiO 3 film on the SrCa 2 Al 2 O 6 layer with atomically smooth surfaces. The SrCa 2 Al 2 O6 layer was subsequently dissolved in de-ionized water to create free-standing SrTiO3 membranes that were transferred onto a metal-coated Si wafer. Membranes created with Sr-deficiency revealed ferroelectric-like behavior measured using piezo force microscopy whereas stoichiometric films remained paraelectric-like. Furthermore, these findings underscore the viability of using ex-situ deposited amorphous SrCa2Al2O6 for epitaxial, single crystalline growth, as well as the importance of point defects in determining the ferroic properties in membranes.