Search NASA⌕ Search

SEARCH · Search NASA

Results for “materials processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

Manufacturing and quality control of FCC harnesses

The Saturn 5 program contractors encountered many technological challenges and problems relative to inter-connecting wiring and cabling during the development stages of the Saturn program. The knowledge gained from solving these problems, plus recently developed state-of-the-art techniques, materials, and processes were documented in a report prepared for NASA/MSFC. The portions of that report which deal with FCC harnesses are presented.

Malohm, W. L.↗

Development of a flat cable system

A flat conductor cabling system for electrical/electronic interwiring is described. Six major items comprise the system: the cables, splices - one for flat cable to round wires and one for flat cable to flat cable; a series of flat cable connectors; the distributor, which is used for interconnecting the circuits; and a repair technique for the falt cable. Polyarylene, a new high performance melt-processable insulation material, permits the design of a completely standardized, modular flat conductor flat cable. The development of an advanced heat-shrinkable plastics technology involving the use of selectively bonded plastic film has resulted in the multiple termination module, used for making high-reliability sealed solder terminations to either flat conductor cable or round wires. All necessary tools and application equipment are included in the system design.

Neel, R. M.↗

Monolayer boron-aluminum compacted sheet material

The manufacturing techniques, basic materials used, and equipment required to produce monolayer boron-aluminum composites are described. Tentative materials and process specifications are included. Improvements in bonding and filament spacing obtained through use of brazing powder in the fugitive binder are discussed.

Sumner, E. V.↗

Rolling-element bearings: A review of the state of the art

Some of the research conducted which has brought rolling-element technology to its present state is discussed. Areas touched upon are material effects, processing variables, operating variables, design optimization, lubricant effects and lubrication methods. Finally, problem areas are discussed in relation to the present state-of-the-art and anticipated requirements.

Anderson, W. J.↗

Time-dependent polar distribution of outgassing from a spacecraft

A technique has been developed to obtain a characterization of the self-generated environment of a spacecraft and its variation with time, angular position, and distance. The density, pressure, outgassing flux, total weight loss, and other important parameters were obtained from data provided by two mass measuring crystal microbalances, mounted back to back, at distance of 1 m from the spacecraft equivalent surface. A major outgassing source existed at an angular position of 300 deg to 340 deg, near the rocket motor, while the weakest source was at the antennas. The strongest source appeared to be caused by a material diffusion process which produced a directional density at 1 m distance of about 1.6 x 10 to the 11th power molecules/cu cm after 1 hr in vacuum and decayed to 1.6 x 10 to the 9th power molecules/cu cm after 200 hr. The total average outgassing flux at the same distance and during the same time span changed from 1.2 x 10 to the minus 7th power to 1.4 x to the minus 10th power g/sq cm/s. These values are three times as large at the spacecraft surface. Total weight loss was 537 g after 10 hr and about 833 g after 200 hr. Self-contamination of the spacecraft was equivalent to that in orbit at about 300-km altitude.

Scialdone, J. J.↗

ASRDI oxygen technology survey, Volume 7: Characteristics of metals that influence system safety

A literature survey and analysis of the material and process factors affecting the safety of metals in oxygen systems is presented. In addition, the practices of those who specify, build, or use oxygen systems relative to the previous is summarized. Alloys based on iron, copper, nickel, and aluminum were investigated representing the bulk of metals found in oxygen systems. Safety-related characteristics of other miscellaneous metals are summarized. It was found that factors affecting the safety of metals in oxygen systems exit in all phases of the evolutionary process, from smelting and mill techniques through end-production fabrication. The safety of a given metal in an oxygen system was determined to be influenced by the particular service requirement. The metal characteristics should favorably influence fulfillment of these requirements. Thus, no singular metal or alloy could be classified as safest for all types of oxygen service.

Pelouch, J. J., Jr.↗

Rolling-element bearings - A review of the state of the art

Some of the research conducted which has brough rolling-element technology to its present state is discussed. Areas touched upon are material effects, processing variables, operating variables, design optimization, lubricant effects and lubrication methods. Finally, problem areas are discussed in relation to the present state-of-the-art and anticipated requirements.

Anderson, W. J.↗

Inhibiting Kirkendall void growth in welded bimetallic structures

Technique employs pre-aged, void-free junction composed of parent materials. Basic process for Kirkendall void inhibition can be applied to thermionic power systems, high temperature seals, high temperature junctions between any two metals of differing melting points where Kirkendall void formation would be detrimental.

Arcella, F. G.↗

Integrated utility system design concept

Conceptual design studies are performed to investigate the feasibility of the MIUS concept as an alternate method of providing utility services to communities and/or community facilities having advantages over current practices. Procured and operated is a large scale testbed of the MIUS concept in order to evaluate and test those integrated system technical details that do not lend themselves to analysis. These include materials compatibility, process instrumentation and control, predictability of water and air effluents, techniques of heat recovery, method of thermal distribution, etc.

Hays, E. L.↗

Titanium honeycomb acoustic lining structural and thermal test report

The results are presented of static, fatigue and thermal testing of titanium honeycomb acoustic panels representing the acoustic tailpipe for the Pratt and Whitney Aircraft JT8D Refan engine which is being studied for use on the Boeing 727-200 airplane. Test specimens represented the engine and tailpipe flange joints, the rail to which the thrust reverser is attached and shear specimens of the tailpipe honeycomb. Specimens were made in four different batches with variations in configuration, materials and processes in each. Static strength of all test specimens exceeded the design ultimate load requirements. Fatigue test results confirmed that aluminum brazed titanium, as used in the Refan tailpipe design, meets the fatigue durability objectives. Quality of welding was found to be critical to life, with substandard welding failing prematurely, whereas welding within the process specification exceeded the panel skin life. Initial fatigue testing used short grip length bolts which failed prematurely. These were replaced with longer bolts and subsequent testing demonstrated the required life. Thermal tests indicate that perforated skin acoustic honeycomb has approximately twice the heat transfer of solid skin honeycomb.

Joynes, D.↗

Molecular fluxes from a spacecraft measured with quartz microbalances

A technique has been developed to obtain a characterization of the self-generated environment of a spacecraft and its variation with time, angular position, and distance. The density, pressure, outgassing flux, total weight loss, and other important parameters were obtained from data provided by two mass measuring crystal microbalances, mounted back to back, at a distance of 1 m from the spacecraft equivalent surface. The strongest source appeared to be caused by a material diffusion process which produced a directional density at 1 m distance of about 160 billion molecules per cu cm after 1 h in vacuum and decayed to 1.6 billion molecules per cu cm after 200 h. Self-contamination of the spacecraft was equivalent to that which occurs in a 300-km altitude orbit.

Scialdone, J. J.↗

High purity silica reflective heat shield development

A high purity slip cast silica material has been developed for use as a reflective heat shield for entries into the atmospheres of the outer planets. The several stages leading to the development of this material are described and details of raw material selection, preparation of the slip material and casting techniques are discussed. Optical (reflectance and transmittance), physical and chemical properties measurements were performed as a function of the important material and processing variables. Performance analysis of a reflective heat shield fabricated from the high purity silica slip shows that approximately 90 percent of the radiant bow shock energy incident on the heat shield during entry into the atmosphere of Jupiter will be reflected.

Blome, J. C.↗

Improved impact-resistant boron-aluminum composites for use as turbine engine fan blades

Efforts to improve the impact resistance of B/Al are reviewed and analyzed. Thin sheet Charpy and Izod impact tests and standard full size Charpy impact tests were conducted on unidirectional and angleply composites containing 4, 5.6 and 8 mil boron in 1100, 2024, 5052 and 6061 Al matrices. Impact failure modes of B/Al are proposed in an attempt to describe the mechanisms involved and to provide insight for maximizing impact resistance. The impact strength of B/Al was significantly increased by proper selection of materials and processing. The use of more ductile matrices (1100 Al) and larger diameter (8 mil) boron fibers gave the highest impact strengths by allowing matrix shear deformation and multiple fiber breakage.

Mcdanels, D. L.↗

Endurance and failure characteristics of main-shaft jet engine bearings at 3x10 to the 6th power DN

Groups of thirty 120-mm bore angular contact ball bearings were endurance tested at a speed of 12,000 and 25,000 rpm and a thrust load of 66 721 N. The bearings were manufactured from a single heat of VIM-VAR AISI M-50 steel. At 1.44X1 million and 3.0x1 million DN, 84 483 and 74 800 bearing test hours were accumulated, respectively. Test results were compared with similar bearings made from CVM AISI M-50 steel run under the same conditions. Bearing lives at speeds of 3x1 million DN with the VIM-VAR AISI M-50 steel were nearly equivalent to those obtained at lower speeds. A combined processing and material life factor of 44 was found for VIM-VAR AISI M-50 steel. Continuous running after a spall has occurred at 3.0x1 million DN can result in a destructive fracture of the bearing inner race.

Bamberger, E. N.↗

Advanced composites: Fabrication processes for selected resin matrix materials

This design note is based on present state of the art for epoxy and polyimide matrix composite fabrication technology. Boron/epoxy and polyimide and graphite/epoxy and polyimide structural parts can be successfully fabricated. Fabrication cycles for polyimide matrix composites have been shortened to near epoxy cycle times. Nondestructive testing has proven useful in detecting defects and anomalies in composite structure elements. Fabrication methods and tooling materials are discussed along with the advantages and disadvantages of different tooling materials. Types of honeycomb core, material costs and fabrication methods are shown in table form for comparison. Fabrication limits based on tooling size, pressure capabilities and various machining operations are also discussed.

Welhart, E. K.↗

Fabrication and testing of sealed silver-zinc cells

A number of Type HS40-7 sealed silver-zinc cells and experimental 40AH sealed silver-zinc cells were fabricated. Cells of each experimental group contained one variation from the standard configuration (HS40-7) cell. Cells from each of five experimental cell groups and cells of the standard configuration were tested to characterize voltage and capacity performance at various discharge rates. The test cells were then subjected to 100 percent DOD Cycle Life Testing at 22 C. Results indicate that material and/or process variations are available which will improve both performance and cycle life of the existing 40 ampere-hour sealed silver-zinc cell configurations. The average cycle life to 50 percent loss of nominal capacity in cells from two (2) of the experimental groups was 150 - 165 cycles. A series of 12 ampere-hour cells was fabricated and tested as part of a program to incorporate the 40AH sealed silver-zinc cell fabrication technology into a cell of smaller size. Base-line configuration cells and experimental variations were produced using the HS40-7 cell fabrication and processing methods adapted to the smaller cell size.

Donnel, C. P., III↗

Studies of encapsulant materials for terrestrial solar-cell arrays

Study 1 of this contract is entitled ""Evaluation of World Experience and Properties of Materials for Encapsulation of Terrestrial Solar-Cell Arrays.'' The approach of this study is to review and analyze world experience and to compile data on properties of encapsulants for photovoltaic cells and for related applications. The objective of the effort is to recommend candidate materials and processes for encapsulating terrestrial photovoltaic arrays at low cost for a service life greater than 20 years. The objectives of Study 2, ""Definition of Encapsulant Service Environments and Test Conditions,'' are to develop the climatic/environmental data required to define the frequency and duration of detrimental environmental conditions in a 20-year array lifetime and to develop a corresponding test schedule for encapsulant systems.

Carmichael, D. C.↗

Early results of the ATS-6 solar cell flight experiment

This paper presents preliminary ATS-6 solar-cell flight-experiment data through the first 247 days in synchronous orbit. The experiment is transmitting data on forty 2 x 2-cm solar cells representing 16 solar-cell configurations. The experiment is designed to study the effect of this orbit on select solar cells and cover-glass parameters such as solar-cell thickness and base resistivity, cover-glass thickness variation, new cover processes, and materials such as 7940 and 7070 integral covers as well as the FEP covers, the COMSAT 'violet' cell, and backside irradiation effects. The in-space solar-cell data indicate short-circuit currents are running higher by 1% to 8% than in measurements made with solar simulations; maximum power varied between -1% and +6%. Degradation of short-circuit current due to ultraviolet effects was determined to be about 2% after 50 days in orbit. All cells performed well through 247 days in orbit except the FEP-covered cells, which appear to have increased their rate of degradation during the eclipse season.

Goldhammer, L. J.↗