Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

Structural anisotropy of nonpolar and semipolar InN epitaxial layers

We present a detailed study of the structural characteristics of molecular beam epitaxy grown nonpolar InN films with a- and m-plane surface orientations on r-plane sapphire and (100) {gamma}-LiAlO{sub 2}, respectively, and semipolar (1011) InN grown on r-plane sapphire. The on-axis rocking curve (RC) widths were found to exhibit anisotropic dependence on the azimuth angle with minima at InN [0001] for the a-plane films, and maxima at InN [0001] for the m-plane and semipolar films. The different contributions to the RC broadening are analyzed and discussed. The finite size of the crystallites and extended defects are suggested to be the dominant factors determining the RC anisotropy in a-plane InN, while surface roughness and curvature could not play a major role. Furthermore, strategy to reduce the anisotropy and magnitude of the tilt and minimize defect densities in a-plane InN films is suggested. In contrast to the nonpolar films, the semipolar InN was found to contain two domains nucleating on zinc-blende InN(111)A and InN(111)B faces. These two wurtzite domains develop with different growth rates, which was suggested to be a consequence of their different polarity. Both, a- and m-plane InN films have basal stacking fault densities similar or even lower compared to nonpolar InN grown on free-standing GaN substrates, indicating good prospects of heteroepitaxy on foreign substrates for the growth of InN-based devices.

36 MATERIALS SCIENCE↗

High-κ TiO{sub 2} thin film prepared by sol-gel spin-coating method

High-k TiO{sub 2} thin film on p-type silicon substrate was fabricated by a combined sol-gel and spin coating method. Thus deposited titania film had anatase phase with a small grain size of 16 nm and surface roughness of ≅ 0.6 nm. The oxide capacitance (C{sub ox}), flat band capacitance (C{sub FB}), flat band voltage (V{sub FB}), oxide trapped charge (Q{sub ot}), calculated from the high frequency (1 MHz) C-V curve were 0.47 nF, 0.16 nF, − 0.91 V, 4.7x10{sup −12} C, respectively. As compared to the previous reports, a high dielectric constant of 94 at 1 MHz frequency was observed in the devices investigated here and an equivalent oxide thickness (EOT) was 4.1 nm. Dispersion in accumulation capacitance shows a linear relationship with AC frequencies. Leakage current density was found in acceptable limits (2.1e-5 A/cm{sup 2} for −1 V and 5.7e-7 A/cm{sup 2} for +1 V) for CMOS applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Remote detection of ocean features in the Lesser Antilles using ERTS-1 data

The author has identified the following significant results. Photographic data received from the ERTS-1 satellite over the Lesser Antilles Islands shows distinct ocean features on the leeward side of each island. Attempts to relate these features to ocean eddy formations with the aid of ground truth data proved unsuccessful. However, analysis of surface and upper air wind data correlate extremely well with the size, shape, and downwind extent of the ocean features. Studies to date indicate strongly that these features result from horizontal differences in sea surface roughness due to the wind shadow effect of the islands. The results suggest that horizontal variations in the reflectance of the sea surface will make remote sensing of the ocean mixed layer more difficult than previously anticipated. The surface reflection seems to be large enough to mask the smaller variations in backscattered energy from the mixed layer. Efforts to limit the effect of surface reflectance by photographic differencing of two MSS bands were unsuccessful. A supplementary study to enhance the energy reflected from the mixed layer through numerical differencing of ERTS-1 digital data is planned.

Hanson, K. J.↗

Remote detection of ocean features in the Lesser Antilles using ERTS-1 data

The author has identified the following significant results. Photographic data received from the ERTS-1 satellite over the Lesser Antilles Islands show distinct ocean features on the leeward side of each island. Attempts to relate these features to ocean eddy formations with the aid of ground truth data proved unsuccessful. However, surface and upper air wind data indicate a good correlation with the size, shape, and downwind extent of the ocean features. Studies to date indicate strongly that these features result from horizontal differences in sea surface roughness due to the wind shadow effect of the islands. The results suggest that horizontal variations in the reflectance of the sea surface will make remote sensing of the ocean mixed layer more difficult than previously anticipated. The surface reflection seems to be large enough to mask the smaller horizontal variations in backscattered energy from the mixed layer.

Hanson, K. J.↗

Symmetry in polarimetric remote sensing

Relationships among polarimetric backscattering coefficients are derived from the viewpoint of symmetry groups. For both reciprocal and non-reciprocal media, symmetry encountered in remote sensing due to reflection, rotation, azimuthal, and centrical symmetry groups is considered. The derived properties are general and valid to all scattering mechanisms, including volume and surface scatterings and their interactions, in a given symmetrical configuration. The scattering coefficients calculated from theoretical models for layer random media and rough surfaces are shown to obey the symmetry relations. Use of symmetry properties in remote sensing of structural and environmental responses of scattering media is also discussed. Orientations of spheroidal scatterers described by spherical, uniform, planophile, plagiothile, erectophile, and extremophile distributions are considered to derive their polarimetric backscattering characteristics. These distributions can be identified from the observed scattering coefficients by comparison with theoretical symmetry calculations. A new parameter is then defined to study scattering structures in geophysical media. Observations from polarimetric data acquired by the Jet Propulsion Laboratory airborne synthetic aperture radar over forests, sea ice, and sea surface are presented. Experimental evidences of the symmetry relationships are shown and their use in polarimetric remote sensing is illustrated. For forests, the coniferous forest in Mt. Shasta area (California) and mixed forest near Presque Isle (Maine) exhibit characteristics of the centrical symmetry at C-band. For sea ice in the Beaufort Sea, multi-year sea ice has a cross-polarized ratio e close to e(sub 0), calculated from symmetry, due to the randomness in the scattering structure. First-year sea ice has e much smaller than e(sub 0) due to the preferential alignment of the columnar structure of the ice. From polarimetric data of a sea surface in the Bering Sea, it is observed that e and e(sub 0) are increasing with incident angle and e is greater than e(sub 0) at L-band because of the directional feature of sea surface waves. Symmetry properties of geophysical media can also be used to calibrate polarimetric radars.

Nghiem, S. V.↗

Using Remote Sensing Platforms to Estimate Near-Surface Soil Properties

Evaluation of near-surface soil properties via remote sensing (RS) could facilitate soil survey mapping, erosion prediction, fertilization regimes, and allocation of agrochemicals. The objective of this study was to evaluate the relationship between soil spectral signature and near surface soil properties in conventionally managed row crop systems. High resolution RS data were acquired over bare fields in the Coastal Plain, Appalachian Plateau, and Ridge and Valley provinces of Alabama using the Airborne Terrestrial Applications Sensor (ATLAS) multispectral scanner. Soils ranged from sandy Kandiudults to fine textured Rhodudults. Surface soil samples (0-1 cm) were collected from 163 sampling points for soil water content, soil organic carbon (SOC), particle size distribution (PSD), and citrate dithionite extractable iron (Fed) content. Surface roughness, soil water content, and crusting were also measured at sampling. Results showed RS data acquired from lands with less than 4 % surface soil water content best approximated near-surface soil properties at the Coastal Plain site where loamy sand textured surfaces were predominant. Utilizing a combination of band ratios in stepwise regression, Fed (r2 = 0.61), SOC (r2 = 0.36), sand (r2 = 0.52), and clay (r2 = 0.76) were related to RS data at the Coastal Plain site. In contrast, the more clayey Ridge and Valley soils had r-squares of 0.50, 0.36, 0.17, and 0.57. for Fed, SOC, sand and clay, respectively. Use of estimated eEmissivity did not generally improve estimates of near-surface soil attributes.

Sullivan, D. G.↗

How Did I Get Here?

What country was responsible for much of the early work in laser altimetry, who was the first scientist to look at a vegetation profile generated by a laser, who first related laser ranges to forest structure? The purpose of this paper is to look back 3+ decades ago when forestry lidar was in its formative years and to give credit to those who first thought to employ a laser to measure the Earth's surface. As with much scientific research, advances were often made independently and concurrently in a number of countries. Functioning lasers were first demonstrated in 1960 in the USA and in 1961 in the USSR, but research into the use of lasers as forest measurement tools did not begin for another IS years. Initially, with respect to Earth resources, lasers were employed to measure sea ice surface roughness, to make near-shore bathymetric measurements, to penetrate forests to make detailed topographic measurements, and to fluoresce oceanic phytoplankton for surface current studies. Some of these early studies noted that forest profiles were evident but in fact added noise to topographic retrievals. Trees became the signal rather than noise in 1976 when researchers in the Canadian Forest Service went to an IUFRO conference in Oslo and reported on efforts to better estimate timber volume in tropical forests. They employed large-scale airphotos (1:500 up to 1:4000) to measure the top of the tropical canopy, an avionic radar to measure the location of the ground beneath the canopy, and a barometric sensor to record aircraft/radar height above a datum (e.g., sea level). Their radar did not work well in dense vegetation and mentioned in passing that a laser altimeter had worked well in Canadian forests. But in a report 2 years later they reported that, on a study area in Costa Rica, the radar ground line was much improved and no mention is made of a lidar altimeter. In the USSR in 1977, Russian researchers felled a birch and a spruce, aimed a helium-neon, 0.63 micron laser with a spot size of approx 25mm, at the horizontal trees, produced a profilograph, compared it to tape measurements, and concluded that, with increased power, such a laser could be mounted on an aircraft to remotely measure forest canopies. In 1979, they mounted their He-Ne laser on an AN-2 biplane and acquired their fIrSt airborne profiles. Scientists with TRANARG, a mapping/surveying company in Caracas, Venezuela, reported on 1976 flights employing a helium-neon lidar to collect over 11,000 km of lidar profiles spaced 1.5 km apart in order to construct a topographic map to help site a new reservoir. They noted 35-40 m median canopy heights with emergents up to 55 m in their profiles. These studies and others that utilize these height and canopy density metrics for forest mensuration are reviewed in this glance backwards at the history of forestry lidar.

Nelson, Ross↗

Alignment nature of ZnO nanowires grown on polished and nanoscale etched lithium niobate surface through self-seeding thermal evaporation method

Highlights: • ZnO nanowires were grown directly on LiNbO{sub 3} surface for the first time by thermal evaporation. • Self-alignment of the nanowires due to step bunching of LiNbO{sub 3} surface is observed. • Increased roughness in surface defects promoted well-aligned growth of nanowires. • Well-aligned growth was then replicated in 50 nm deep trenches on the surface. • Study opens novel pathway for patterned growth of ZnO nanowires on LiNbO{sub 3} surface. - Abstract: High aspect ratio catalyst-free ZnO nanowires were directly synthesized on lithium niobate substrate for the first time through thermal evaporation method without the use of a buffer layer or the conventional pre-deposited ZnO seed layer. As-grown ZnO nanowires exhibited a crisscross aligned growth pattern due to step bunching of the polished lithium niobate surface during the nanowire growth process. On the contrary, scratches on the surface and edges of the substrate produced well-aligned ZnO nanowires in these defect regions due to high surface roughness. Thus, the crisscross aligned nature of high aspect ratio nanowire growth on the lithium niobate surface can be changed to well-aligned growth through controlled etching of the surface, which is further verified through reactive-ion etching of lithium niobate. The investigations and discussion in the present work will provide novel pathway for self-seeded patterned growth of well-aligned ZnO nanowires on lithium niobate based micro devices.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Pulsed laser deposition of niobium nitride thin films

Niobium nitride (NbN{sub x}) films were grown on Nb and Si(100) substrates using pulsed laser deposition. NbN{sub x} films were deposited on Nb substrates using PLD with a Q-switched Nd:YAG laser (λ = 1064 nm, ∼40 ns pulse width, and 10 Hz repetition rate) at different laser fluences, nitrogen background pressures and deposition substrate temperatures. When all the fabrication parameters are fixed, except for the laser fluence, the surface roughness, nitrogen content, and grain size increase with increasing laser fluence. Increasing nitrogen background pressure leads to a change in the phase structure of the NbN{sub x} films from mixed β-Nb{sub 2}N and cubic δ-NbN phases to single hexagonal β-Nb{sub 2}N. The substrate temperature affects the preferred orientation of the crystal structure. The structural and electronic, properties of NbN{sub x} deposited on Si(100) were also investigated. The NbN{sub x} films exhibited a cubic δ-NbN with a strong (111) orientation. A correlation between surface morphology, electronic, and superconducting properties was found. The observations establish guidelines for adjusting the deposition parameters to achieve the desired NbN{sub x} film morphology and phase.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Growth mechanism of ZnO low-temperature homoepitaxy

The authors report on the growth mechanism of ZnO homoepitaxy at the low-temperature range of 500 deg. C, which is unavailable to obtain high-quality ZnO films in heteroepitaxy. One typical set of ZnO films were grown on (0001) ZnO substrates by molecular-beam epitaxy: a standard structure without buffer and two buffered structures with high-temperature (HT) homobuffer and low-temperature (LT) homobuffer. As a result, the LT homobuffered structure had the outstanding material properties: the surface roughness is 0.9 nm, the full width at half maximum of x-ray rocking curve is 13 arcsec, and the emission linewidth of donor-bound excitons is 2.4 meV. In terms of the theoretical interpretation of the experimentally obtained electron mobilities, it was found that the LT homobuffered structure suffers less from the dislocation scattering and the ionized-impurity scattering compared to the HT homobuffered structure. It is proposed that, in the ZnO low-temperature homoepitaxy, the LT homobuffer plays a key role in inducing the complete termination of dislocations in the homointerface and suppressing the outdiffusion of contaminants and point defects on the ZnO surface, which results in the formation of smooth wetting layer on the homointerface.

36 MATERIALS SCIENCE↗

Enhancement of effective linear RF surface resistance of superconducting surfaces by microscopic topography

Minimization of Radio-Frequency (RF) dissipation on superconducting surfaces is of interest for many applications. A prominent one is the use of Superconducting RF (SRF) cavities for charged particle acceleration. In addition to our previous investigation which characterized the occurrence of high-field non-linear losses by microscopic surface topography, the topic of increased linear losses as a function of surface topographic character merits consideration. Surfaces with isotropic homogeneous surface topography may be well characterized by power spectral density (PSD) derived from systematic height measurements. PSD characterizations of representative niobium cavity surface treatments have been developed: Electro-Polishing (EP), Nano-Mechanical Polishing (NMP) and Centrifugal Barrel Polishing (CBP) A perturbation model based on PSD statistical analysis is used to calculate additional RF loss on these surfaces when superconducting. The model assesses the penetration depth effects for a superconductor. We thus estimate the RF power dissipation ratio between these rough surfaces and an ideal smooth surface.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

The detection by ERTS-1 of wind-induced ocean surface features in the lee of the Antilles Islands

Photographic data received from the ERTS-1 satellite over the Lesser Antilles Islands show distinct ocean features on the leeward side of each island. Attempts to relate these features to ocean eddy formations with the aid of ground truth data proved unsuccessful. However, surface and upper air wind data indicate a good correlation with the size, shape, and downwind extent of the ocean features. Studies to date indicate strongly that these features result from horizontal differences in a sea surface roughness due to the wind-shadow effect of the islands. The results suggest that horizontal variations in the reflectance of the sea surface will make remote sensing of the ocean mixed layer more difficult than previously anticipated. The surface reflection seems to be large enough to mask the smaller variations in backscattered energy from the mixed layer. Efforts to limit the effect of surface reflectance by photographic differencing of two multi-spectral scanner bands were unsuccessful.

Cram, R.↗

An experimental study of heat transfer in a large-scale turbine rotor passage

An experimental study of the heat transfer distribution in a turbine rotor passage was conducted in a large-scale, ambient temperature, rotating turbine model. Heat transfer was measured for both the full-span suction and pressure surfaces of the airfoil as well as for the hub endwall surface. The objective of this program was to document the effects of flow three-dimensionality on the heat transfer in a rotating blade row (vs a stationary cascade). Of particular interest were the effects of the hub and tip secondary flows, tip leakage and the leading-edge horseshoe vortex system. The effect of surface roughness on the passage heat transfer was also investigated. Midspan results are compared with both smooth-wall and rough-wall finite-difference two-dimensional heat transfer predictions. Contour maps of Stanton number for both the rotor airfoil and endwall surfaces revealed numerous regions of high heat transfer produced by the three-dimensional flows within the rotor passage. Of particular importance are regions of local enhancement (as much as 100 percent over midspan values) produced on the airfoil suction surface by the secondary flows and tip-leakage vortices and on the hub endwall by the leading-edge horseshoe vortex system.

Blair, Michael F.↗

Surface morphology of molecular-beam epitaxially grown Si(1-x)Ge(x) layers on (100) and (110) Si

The surface morphology and dislocation structure of Si(1-x)Ge(x) layers grown on (100) and (110) Si substrates have been investigated using atomic force microscopy, and scanning and transmission electron microscopy. The layers, which have up to a 1.2 percent lattice mismatch with the substrates, were grown by molecular-beam epitaxy at 550 C at thicknesses above those required for the introduction of dislocations. Si(1-x)Ge(x) layers grown on (100) show a crosshatch morphology which is correlated to the underlying misfit dislocation network. Annealing greatly enhances the surface roughness producing a partial islanding growing on the preexisting crosshatch morphology. On the (110) substrates no annealing is necessary to produce a roughened surface. The roughened surface morphology is analyzed as a strain-reducing growth mode which enables partial relaxation of the near-surface atomic planes.

Pike, W. T.↗

The SMAP Level 4 Surface and Root-zone Soil Moisture (L4_SM) Product

The Soil Moisture Active and Passive (SMAP) mission is being developed by NASA for launch in 2013 as one of four first-tier missions recommended by the U.S. National Research Council Committee on Earth Science and Applications from Space in 2007. The primary science objectives of SMAP are to enhance understanding of land surface controls on the water, energy and carbon cycles, and to determine their linkages. Moreover, the high resolution soil moisture mapping provided by SMAP has practical applications in weather and seasonal climate prediction, agriculture, human health, drought and flood decision support. In this paper we describe the assimilation of SMAP observations for the generation of the planned SMAP Level 4 Surface and Root-zone Soil Moisture (L4_SM) product. The SMAP mission makes simultaneous active (radar) and passive (radiometer) measurements in the 1.26-1.43 GHz range (L-band) from a sun-synchronous low-earth orbit. Measurements will be obtained across a 1000 km wide swath using conical scanning at a constant incidence angle (40 deg). The radar resolution varies from 1-3 km over the outer 70% of the swath to about 30 km near the center of the swath. The radiometer resolution is 40 km across the entire swath. The radiometer measurements will allow high-accuracy but coarse resolution (40 km) measurements. The radar measurements will add significantly higher resolution information. The radar is however very sensitive to surface roughness and vegetation structure. The combination of the two measurements allows optimal blending of the advantages of each instrument. SMAP directly observes only surface soil moisture (in the top 5 cm of the soil column). Several of the key applications targeted by SMAP, however, require knowledge of root zone soil moisture (approximately top 1 m of the soil column), which is not directly measured by SMAP. The foremost objective of the SMAP L4_SM product is to fill this gap and provide estimates of root zone soil moisture that are informed by and consistent with SMAP observations. Such estimates are obtained by merging SMAP observations with estimates from a land surface model in a soil moisture data assimilation system. The land surface model component of the assimilation system is driven with observations-based surface meteorological forcing data, including precipitation, which is the most important driver for soil moisture. The model also encapsulates knowledge of key land surface processes, including the vertical transfer of soil moisture between the surface and root zone reservoirs. Finally, the model interpolates and extrapolates SMAP observations in time and in space. The L4_SM product thus provides a comprehensive and consistent picture of land surface hydrological conditions based on SMAP observations and complementary information from a variety of sources. The assimilation algorithm considers the respective uncertainties of each component and yields a product that is superior to satellite or model data alone. Error estimates for the L4_SM product are generated as a by-product of the data assimilation system.

Reichle, Rolf↗

The Effect of Composition on the Surface Finish of PS400: A New High Temperature Solid Lubricant Coating

A new composite, multi-constituent, solid lubricant coating, NASA PS400, developed for high temperature tribological applications, exhibits a smoother surface finish after grinding and polishing than its predecessors PS200 and PS300. In this paper, the baseline composition of PS400 is modified to investigate each individual constituent s role on the achievable surface finish through a series of coating deposition, grinding, and polishing experiments. Furthermore, to explore the limits of compositional tailoring for improved tribological performance, several PS400 coatings were doped with additional solid lubricants (graphite, MoS2 and BN) and tribologically tested. The test results clearly showed that, compared to PS300 coatings, PS400 achieves a smoother surface finish via a reduced lubricant content. Coatings prepared with higher than the baseline level (10 wt%) of lubricants exhibited higher final surface roughness than the earlier generation PS300 coatings. Reducing or eliminating the one or both lubricants (fluorides or silver) did not further improve the surface finish suggesting that the current composition of PS400 is near optimal with respect to surface finish. Lastly, attempts to improve the poor initial room temperature tribological behavior of PS400 via the addition of traditional solid lubricants were unsuccessful. Based upon this work and earlier results it is expected that future research will concentrate on developing methods to produce a lubricious glaze on the rubbing surface during break in to ensure that low friction and wear are rapidly achieved.

DellaCorte, Christopher↗

Post-Flight Assessment of Avcoat Thermal Protection System for the Exploration Flight Test-1

On December 5, 2014 NASA conducted the first flight test of its next generation human-class Orion spacecraft. The flight was called the Exploration Flight Test -1 (EFT-1) which lasted for 4 hours and culminated into a re-entry trajectory at 9 km/s. This flight test of the 5-meter Orion Crew Module demonstrated various sub-systems including the Avcoat ablative thermal protection system (TPS) on the heat shield. The Avcoat TPS had been developed from the Apollo-era recipe with a few key modifications. The engineering for thermal sizing was supported by modeling, analysis, and ground tests in arc jet facilities. This paper will describe a postlfight analysis plan and present results from post-recovery inspections, data analysis from embedded sensors, TPS sample extraction and characterization in the laboratory. After the recovery of the vehicle, a full photographic survey and surface scans of the TPS were performed. The recovered vehicle showed physical evidence of flow disturbances, varying degrees of surface roughness, and excessive recession downstream of compression pads. The TPS recession was measured at more than 200 locations of interest on the Avcoat surface. The heat shield was then processed for sample extraction prior to TPS removal using the 7-Axis Milling machine at Marshall Space Flight Center. Around 182 rectangular TPS samples were extracted for subsequent analysis and investigation. The final paper will also present results of sample analysis. The planned investigation includes sidewall imaging, followed by image analysis to characterize TPS response by quantifying different layers in the char and pyrolysis zones. A full postmortem of the instrumentation and sensor ports will also be performed to confirm no adverse effects due to the sensors themselves. A subset of the samples will undergo structural testing and perform detailed characterization of any cracks and integrity of gore seams. Finally, the material will be characterized with layer-by-layer density measurements and SEM investigations to evaluate material morphology at microstructural level including identification of elements and compounds.

Aerothermodynamics↗

Optoheterodyne Doppler measurements of the ballistic expansion of the products of the shock wave-induced surface destruction: Experiment and theory

The results of optoheterodyne Doppler measurements of the ballistic expansion of the products of surface destruction under shock-wave loading are presented. The possibility of determining the physical characteristics of a rapidly flying dust cloud, including the microparticle velocities, the microparticle sizes, and the areal density of the dust cloud, is shown. A compact stand for performing experiments on shock-wave loading of metallic samples is described. Shock-wave loading is performed by a 100-µm-thick tantalum flyer plate accelerated to a velocity of 2.8 km/s. As the samples, lead plates having various thicknesses and the same surface roughness are used. At a shock-wave pressure of 31.5 GPa, the destruction products are solid microparticles about 50 µm in size. At a pressure of 42 and 88 GPa, a liquid-drop dust cloud with a particle size of 10–15 µm is formed. To interpret the spectral data on the optoheterodyne Doppler measurements of the expansion of the surface destruction products (spalled fragments, dust microparticles), a transport equation for the function of mutual coherence of a multiply scattered field is used. The Doppler spectra of a backscattered signal are calculated with the model developed for the dust cloud that appears when a shock wave reaches the sample surface at the parameters that are typical of an experimental situation. Qualitative changes are found in the spectra, depending on the optical thickness of the dust cloud. The obtained theoretical results are in agreement with the experimental data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗