Search NASA⌕ Search

SEARCH · Search NASA

Results for “ACTIVE RECEIVER RADIOMETER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Low-cost 20-22 GHz MIC active receiver/radiometer

A microwave integrated circuit active receiver is built and tested at 19-25 GHz. The receiver consists of a planar CPW-fed double folded-slot antenna coupled to a six-stage MESFET (metal semiconductor field effect transistors) amplifier and followed by a planar Schottky-diode detector. The folded-slot antenna on a GaAs half-space results in a wide frequency bandwidth suitable for MMIC amplifiers. The measured system performance show a video responsivity close to 1 GV/W at 20 GHz with a 3-dB bandwidth of 1500 MHz. A novel method which uses the planar video detector after the amplifier stages as an RF (radio frequency) mixer is used to measure the noise-figure of the direct detection radiometer. The system noise figure is 4.8 dB at 22 GHz. The radiometer sensitivity to a hot/cold load is 3.8 mu V/K. The measured antenna patterns show a 90% Gaussicity at 20-22 GHz. The active MIC receiver can be integrated monolithically for low-cost applications and is well suited for millimeter-wave linear imaging arrays.

PLANAR SCHOTTKY DIODE DETECTOR↗
NASA NTRS1976

Correlation between microwave scattering and emission from land and sea at 13.9 GHz

Correlations have been calculated between active and passive microwave responses received by the S-193 radiometer-scatterometer on Skylab. Over both land and sea, the correlations between polarizations are high, but the correlation between radiometer and scatterometer response at 30-deg incidence is negligible. This suggests that multipolarization instruments with this crude resolution (greater than 10 km in all cases) are redundant, but a combination of radiometer and scatterometer is useful. Correlations among the responses at different angles suggest that the five angles used in Skylab are more than would be useful between zero and 48 deg in future instruments, but that instruments with three angles of measurement would be useful. In small areas, conclusions based on these large-data-set averages may need to be modified.

Sobti, A.↗
NASA NTRS1994

Investigation of passive atmospheric sounding using millimeter and submillimeter wavelength channels

Progress by the Georgia Institute of Technology's Laboratory for Radio-science and Remote Sensing in developing techniques for passive microwave retrieval of water vapor profiles and cloud and precipitation parameters using millimeter and submillimeter wavelength channels is reviewed. Channels of particular interest are in the tropospheric transmission windows at 90, 166, 220, 340, and 410 GHz and centered around the water vapor lines at 183 and 325 GHz. Collectively, these channels have potential application in high-resolution precipitation mapping (e.g., from geosynchronous orbit), remote sensing of cloud and precipitation parameters, including cirrus ice mass, and improved retrieval of water vapor profiles. During the period from January 1, 1994 through June 30, 1994 research activities focussed on calibrating and interpreting data from the Millimeter-Wave Imaging Radiometer (MIR). The MIR was deployed on the NASA ER-2 during the Convective Atmospheric Moisture Experiment (CAMEX, September-October 1993) to obtain the first submillimeter-wave tropospheric imagery of convective precipitations. A 325-GHz radiometer consisted of a submillimeter-wave DSB receiver with three IF channels at +/- 1, 3, and 8.5 GHz, and approximately 14 dB DSB noise figure was successfully operated during these experiments. Activities supported under this grant include a study of the impact of local oscillator reflections from the MIR calibration loads, the development of optimal gain and offset filters for radiometric calibration, and the modeling and interpretation of the MIR 325-GHz data over both clear and cloudy atmospheres. In addition, polarimetric radiometer measurements and modeling for ocean surface and atmospheric cloud-ice studies_were supported.

Gasiewski, Albin J.↗
NASA NTRS1976

DSN research and technology support

Continuing testing and refinement of the remote controlled, unattended automated pulsar observing station is noted, along with routine pulsar observations of 22 pulsars. Radar observations of geostationary satellite are discussed. Current status of the 400-kW X-band radar is reported along with routine automatic testing of the stability-reliability of the DSS 13 maser-receiver noise adding radiometer combination. A failure in the Faraday rotation receiving system is noted along with discussion in some detail of the activities of the high power transmitter maintenance facility. Continuation of receiver phase stability testing, specifically the effects of temperature on coaxial cables, is discussed and results reported. A demonstration at full power of the microwave power transmission facility is noted and routine support of the planetary radio astronomy experiment is discussed. Transmission of master clock synchronization signals to overseas DSN stations is also reported.

Jackson, E. B.↗
NASA NTRS2019

Mitigating Interference from Urban Air Mobility Vehicles on Satellite Communication Links by Using Vortex Radiometry

Vortex radiometers (VR) establish an early warning system for communication systems by generating concentric annular beam patterns around the active link. Received power peaks are monitored as interfering signals traverse overhead, allowing the VR to estimate source velocity. From this information the VR determines 1) when a fade will occur, 2) how long the fade will persist for and 3) how intense the fade will be. This paper demonstrates how VRs can be used to increase the resilience of communication systems used in urban air mobility applications.

vortex radiometry↗
NASA NTRS2019

Mitigating Interference from Urban Air Mobility Vehicles on Satellite Communication Links by Using Vortex Radiometry

Vortex radiometers (VRs) establish an early warning system for communication channels by generating concentric annular beam patterns around the active link. Peaks in received power are monitored as interfering signals traverse overhead, allowing the VR to estimate source velocity. From this information the VR determines 1) when a fade will occur, 2) how long the fade will persist for and 3) how intense the fade will be. This paper demonstrates how VRs can increase the resilience of communication systems used in urban air mobility applications.

Schemmel, Peter J.↗
NASA NTRS2021

Study of a Strong RFI Source at L-Band Using SMAP Radiometer Data

This paper presents an analysis of Radio Frequency Interference (RFI) in the 1.400-1.427 GHz frequency band. The study considers the sudden and strong increase of interference from a particular emitter in China that has been observed in July 2020 by radiometers from both ESA's SMOS (Soil Moisture Ocean Salinity) and NASA's SMAP (Soil Moisture Active Passive) missions. It provides an example of the characterization of a source of RFI and illustrates the capabilities of the SMAP radiometer receiver and RFI processing incorporated in it to identify and understand interference.

Radio Frequency Interface↗
NASA NTRS1978

Atmospheric monitoring using heterodyne detection techniques

Both passive and active remote-monitoring instruments using discretely tunable infrared gas lasers and heterodyne receivers have been used for measurements of ozone and other trace constituents in the atmosphere. A ground-based solar heterodyne radiometer has been used in discrete spectral regions near 9.5 microns to measure altitude profiles of ozone in both the troposphere and stratosphere. Results indicate that this technique shows promise in providing calibration points for earth-orbiting ozone-measurement instruments. An airborne laser absorption spectrometer has been used to measure tropospheric ozone in two series of flights during the winter and spring of 1977, and these operations are described. Plans are also in progress to fly a balloon-borne heterodyne radiometer during the fall of 1977 in order to measure stratospheric trace species.

Menzies, R. T.↗
NASA NTRS1992

ACTS propagation terminal update

The activities at Virginia Polytechnic Institute and State University in preparation for the February 1993 launch of ACTS are summarized. ACTS propagation terminals (APT) are being constructed to receive the 20 and 27.5 GHz ACTS beacon signals. Total power radiometers operating at the same frequencies are integrated into the terminal for use in level setting. Recent progress and plans for APT's are reported.

Stutzman, Warren L.↗
NASA NTRS2007

Lessons Learned from the Aquarius Radiometer Engineering Model

The Aquarius instrument is a combination microwave radiometer and scatterometer operating in the L-band for the measurement of sea surface salinity (SSS) over the open-ocean. "The Aquarius science goals are to observe and model the processes that relate salinity variations to climatic changes in the global cycling of water and to understand how these variations influence the general ocean circulation. By measuring salinity globally and synoptically every month for 3 years, Aquarius will provide an unprecedented new view of the ocean's role in climate." (http://aquarius.asfc.nasa.gov on Jan. 4, 2007). To launch in 2009, Aquarius will provide 8-day global coverage and monthly-averaged salinity maps at approx.120-km spatial resolution. Because the microwave emissivity of the ocean surface is weakly dependent upon salinity, the Aquarius radiometer remain sufficiently stable to provide accurate salinity measurements. An engineering model (EM) of one radiometer receiver was developed and tested for functionality and performance at NASA's Goddard Space Flight Center. It was tested for long-term stability starting July 27,2006. Two discrepancies where found at the start of testing and a four-month correction process ensued. This paper covers the testing and debugging of the EM radiometer through resolution of the problems. The radiometer is required to have calibration stability of less than or equal to 0.15 K over 7 days. The radiometer is in a three-beam push-broom configuration with each beam being an independent three-state Dicke radiometer (antenna, reference load, and additive noise). Internal noise diodes and reference loads provide periodic and rapid calibration of the receiver. Front-end loss contributions must be corrected as the lossy components are outside the calibration loop. A key design feature for obtaining stability is active thermal control of the front-end lossy components and the RF receiver. The thermal stability is predicted to be about 0.1 C over an orbit and no more than 1 C over a year. The radiometric stability requirement is 0.13 K rms 1 7 days without using temperature corrections. Temperature corrections and post-launch calibration are expected to extend the stability period through the life of the mission.

Piepmeier, Jeffrey↗
DOE OSTI2022

Effect of Quartz Aperture Covers on the Fluid Dynamics and Thermal Efficiency of Falling Particle Receivers

Falling particle receivers are an emerging technology for use in concentrating solar power systems. In this paper, quartz half-shells are investigated for use as full or partial aperture covers to reduce receiver thermal losses. Quartz half-shell aperture covers offer the ability to minimally interfere with incoming solar radiation from the heliostat field while obstructing thermal radiation and advection from leaving the receiver cavity. The fluid dynamics and heat transfer of a receiver subdomain and surrounding air are modeled using ANSYS®FLUENT We compare the percentage of total incident solar power lost due to conduction through the receiver walls, advective losses through the aperture, and radiation exiting the aperture. Contrary to expected outcomes, results show that quartz aperture covers can increase radiative losses and result in modest to nonexistent reductions in advective losses. The increased radiative losses are driven by elevated quartz half-shell temperatures and have the potential to be mitigated by active cooling and/or material selection. Quartz half-shell total transmissivity was measured experimentally using a radiometer and the National Solar Thermal Test Facility heliostat field with values up to 0.97 ± 0.01. Quartz half-shell aperture covers did not yield expected efficiency gains in numerical results due to increased radiative losses, but efficiency improvement in some numerical results and the performance of quartz half-shells subject to concentrated solar radiation suggest that quartz half-shell aperture covers should be investigated further.

14 SOLAR ENERGY↗
NASA NTRS2011

RFI Mitigation and Detection for the SMAP Radar

The planned Soil Moisture Active Passive (SMAP) mission will use both active radar and passive radiometer instruments at L-Band to measure and monitor both soilmoisture and freeze/thaw state globally. The frequency band allocated for the SMAP radar is shared with the Global Navigation Satellite Systems and ground-basedradiolocation services. Signals from those users present significant sources of anthropogenic radio frequency interference (RFI) which contaminate the radarmeasurements. To mitigate RFI, the radar is designed with tunable operating frequency, which allows the center frequency to be tuned to avoid RFI. The filtering scheme in the receiver is configured to get a high level of RFI suppression. To meet the high accuracy measurement requirements, RFI detection and correction will be required during ground data processing. Some candidate algorithms have been evaluated, and they have been tested against simulated SMAP data derived from the PALSAR data.

Soil Moisture Active Passive (SMAP)↗
NASA NTRS1991

The comet rendezvous asteroid flyby mission: A status report

The Comet Rendezvous Asteroid Flyby (CRAF) mission received a new start in fiscal year 1990. CRAF will match orbits with an active short-period comet and follow it around the Sun, making scientific measurements of the nucleus, coma, and tail. The Imaging system will map the nucleus surface at a resolution of 1 meter/line-pair or better, while Visible and Infrared Mapping Spectrometer (VIMS) and Thermal Infrared Radiometer Experiment (TIREX) will produce spectral and thermal maps of the surface. Onboard instruments will collect cometary dust, ice, and gases and perform elemental and molecular analysis. A suite of fields and particles instruments will observe the solar wind interaction with the cometary atmosphere and tail. Radio tracking of the spacecraft will provide an accurate measure of the nucleus mass and higher harmonics in the comet's gravity field. En route to the comet, the spacecraft will make a close flyby of a large asteroid, preferably a primitive type from the outer main belt. Observations at the asteroid include remote sensing mapping of the surface, detection of any solar wind interaction observable at the flyby distance, and measurement of the asteroid mass to better than 10 percent accuracy. Detailed design of the CRAF spacecraft is currently underway at the Jet Propulsion Laboratory (JPL). Recent mass growth has necessitated a switch to Venus-Earth gravity assist type trajectories, similar to that used by the Galileo spacecraft. These trajectories require longer flight times from launch to rendezvous with the target comet. The details of the current baseline mission, spacecraft design, and instrument payload will be reviewed.

Weissman, Paul R.↗
NASA NTRS1981

Microwave remote sensing: Active and passive. Volume 1 - Microwave remote sensing fundamentals and radiometry

The three components of microwave remote sensing (sensor-scene interaction, sensor design, and measurement techniques), and the applications to geoscience are examined. The history of active and passive microwave sensing is reviewed, along with fundamental principles of electromagnetic wave propagation, antennas, and microwave interaction with atmospheric constituents. Radiometric concepts are reviewed, particularly for measurement problems for atmospheric and terrestrial sources of natural radiation. Particular attention is given to the emission by atmospheric gases, clouds, and rain as described by the radiative transfer function. Finally, the operation and performance characteristics of radiometer receivers are discussed, particularly for measurement precision, calibration techniques, and imaging considerations.

Ulaby, F. T.↗
NASA NTRS2021

Study of a Strong L-Band RFI Source

CN006 is the name given by the European Space Agency (ESA) in their reports on radio frequency interference (RFI) to an instance of RFI in the L-band spectral window at 1.413 GHz protected for passive use only. The source of the interference is located east of the Chinese city of Hangzhou in an area with radar installations. Its effect was initially indistinguishable from that of many such RFI sources observed by the ESA's SMOS and NASA's Soil Moisture Active Passive (SMAP) radiometers over China. However, in July 2020, the level of radiation increased dramatically reaching levels exceeding 1700000 K as reported by Soil Moisture and Ocean Salinity (SMOS) becoming the strongest source observed by SMOS. This article describes an analysis of this very strong source (a radar). It provides information to provide insight into an example of a well-defined source of RFI and illustrates the powerful capability of the SMAP radiometer receiver and RFI processing incorporated in it for identifying and understanding interference.

Radio Frequency Interface↗
NASA NTRSDate not supplied

Creating Gridded Fire Probability Maps using NASA Data

Fire is a nationally and globally significant process that strongly affects human–dominated and wild landscapes. Even though fire can be devastating, wildland fire is a natural and integral force on our landscapes, providing value by decreasing fuels at the Wildland Urban Interface (WUI) to promote safe communities. However, uncontained wildfires can devastate communities, threaten our health, and result in substantial economic losses. There has been greater than a $50B increase in wildfire insurance claims from 2017-2021, which has been exacerbated by climate change. Our partners at Kettle reinsurance are focused on building a smarter reinsurance model for protecting today’s globalized world from the catastrophic effects of climate change. Our objective is to develop the world's first grid-based wildfire probability product using multiple sources of satellite data to determine whether a ‘conflagration' (fire larger than 999+ acres) has ‘breached’ a grid cell. This will substantially decrease the time it takes for homeowners to receive payouts, from over a year to a couple months. Working with our partners at Kettle reinsurance, we use multiple satellites and ancillary data to weigh the likelihood of fire, based on a number of sources that verify a fire burning in a grid cell and the level of confidence in the data source. For example, Sentinel-2 vegetation-change indices have a higher level of confidence than VIIRS (Visible Infrared Imaging Radiometer Suite) active-fire detection data; and VIIRS active-fire detection data have a higher-level of confidence than MODIS (Moderate Resolution Imaging Spectroradiometer) active-fire detection data. The first iteration has been developed for responding to wildfires in California, with the possibility to expand nationwide and globally.

Emily Gargulinski↗
NASA NTRS2013

NASA Tech Briefs, May 2013

Topics include: Test Waveform Applications for JPL STRS Operating Environment; Pneumatic Proboscis Heat-Flow Probe; Method to Measure Total Noise Temperature of a Wireless Receiver During Operation; Cursor Control Device Test Battery; Functional Near-Infrared Spectroscopy Signals Measure Neuronal Activity in the Cortex; ESD Test Apparatus for Soldering Irons; FPGA-Based X-Ray Detection and Measurement for an X-Ray Polarimeter; Sequential Probability Ratio Test for Spacecraft Collision Avoidance Maneuver Decisions; Silicon/Carbon Nanotube Photocathode for Splitting Water; Advanced Materials and Fabrication Techniques for the Orion Attitude Control Motor; Flight Hardware Packaging Design for Stringent EMC Radiated Emission Requirements; RF Reference Switch for Spaceflight Radiometer Calibration; An Offload NIC for NASA, NLR, and Grid Computing; Multi-Scale CNT-Based Reinforcing Polymer Matrix Composites for Lightweight Structures; Ceramic Adhesive and Methods for On-Orbit Repair of Re-Entry Vehicles; Self-Healing Nanocomposites for Reusable Composite Cryotanks; Pt-Ni and Pt-Co Catalyst Synthesis Route for Fuel Cell Applications; Aerogel-Based Multilayer Insulation with Micrometeoroid Protection; Manufacturing of Nanocomposite Carbon Fibers and Composite Cylinders; Optimized Radiator Geometries for Hot Lunar Thermal Environments; A Mission Concept: Re-Entry Hopper-Aero-Space-Craft System on-Mars (REARM-Mars); New Class of Flow Batteries for Terrestrial and Aerospace Energy Storage Applications; Reliability of CCGA 1152 and CCGA 1272 Interconnect Packages for Extreme Thermal Environments; Using a Blender to Assess the Microbial Density of Encapsulated Organisms; Mixed Integer Programming and Heuristic Scheduling for Space Communication; Video Altimeter and Obstruction Detector for an Aircraft; Control Software for Piezo Stepping Actuators; Galactic Cosmic Ray Event-Based Risk Model (GERM) Code; Sasquatch Footprint Tool; and Multi-User Space Link Extension (SLE) System.

Source record↗
NASA NTRSDate not supplied

Creating IR-verified Gridded Fire Burn Maps using Public NASA and Satellite Data

Even though fire can be devastating, wildland fire is a natural and integral force on our landscapes, providing value by decreasing fuels at the Wildland Urban Interface (WUI) to promote safe communities. However, uncontained wildfires can devastate communities, threaten our health, and result in substantial economic losses. There has been greater than a $50B increase in wildfire insurance claims from 2017-2021, which has been exacerbated by climate change. Our partners at Kettle reinsurance are focused on building a smarter reinsurance model for protecting today’s globalized world from the catastrophic effects of climate change. Our objective is to develop a high-confidence grid-based wildfire burn product using multiple sources of satellite data to determine whether a ‘conflagration' (fire larger than 999+ acres) has ‘breached’ a grid cell. This product will substantially decrease the time it takes for homeowners to receive payouts, from over a year to a couple months. Working with our partners at Kettle reinsurance, we use VIIRS (Visible Infrared Imaging Radiometer Suite) 375 m fire detections and Sentinel-2 10 m satellite imagery to create a 20-m gridded fire burn product. Our process is based on the level of confidence in the data source and takes into account vegetation change throughout the life of the fire. For example, Sentinel-2 vegetation-change indices have a higher level of confidence when congruent with VIIRS active-fire detection data, rather than VIIRS detections alone. We have also verified our fire burn product against MODIS/ASTER Airborne Simulator (MASTER) Infrared (IR) data from the Fire Influence on Regional to Global Environments Experiment - Air Quality (FIREX-AQ) 2019 campaign, with 88% overall agreement. The first iteration has been developed for responding to wildfires in California, with the possibility to expand nationwide and globally.

Emily Gargulinski↗