Search NASA⌕ Search

SEARCH · Search NASA

Results for “AFTER-HEAT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Design considerations and experimental observations for the TAMU air-cooled reactor cavity cooling system for the VHTR

The Reactor Cavity Cooling System (RCCS) is a promising passive decay heat removal system for the Very High Temperature Reactor (VHTR) to ensure reliability of the transfer of the core residual and decay heat to the environment under all off-normal circumstances. A small scale experimental test facility was constructed at Texas A and M University (TAMU) to study pertinent multifaceted thermal hydraulic phenomena in the air-cooled reactor cavity cooling system (RCCS) design based on the General Atomics (GA) concept for the Modular High Temperature Gas-Cooled Reactor (MHTGR). The TAMU Air-Cooled Experimental Test Facility is ⅛ scale from the proposed GA-MHTGR design. Groundwork for experimental investigations focusing into the complex turbulence mixing flow behavior inside the upper plenum is currently underway. The following paper illustrates some of the chief design considerations used in construction of the experimental test facility, complete with an outline of the planned instrumentation and data acquisition methods. Computational Fluid Dynamics (CFD) simulations were carried out to furnish some insights on the overall behavior of the air flow in the system. CFD simulations assisted the placement of the flow measurement sensors location. Preliminary experimental observations of experiments at 120oC inlet temperature suggested the presence of flow reversal for cases involving single active riser at both 5 m/s and 2.25 m/s, respectively and four active risers at 2.25 m/s. Flow reversal may lead to thermal stratification inside the upper plenum by means of steady state temperature measurements. A Particle Image Velocimetry (PIV) experiment was carried out to furnish some insight on flow patterns and directions.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Process Evaluation of AISI 4340 Steel Manufactured by Laser Powder Bed Fusion

Laser powder bed fusion (L-PBF) involves the consolidation of metal powder, layer by layer, through laser melting and solidification. In this study, process parameters are optimized for AISI 4340 steel to produce dense and homogeneous structures. The optimized process parameters produce mechanical properties at the center of the build plate that are comparable to wrought in the vertical and horizontal orientations after heat treatment and machining. Four subsequent builds are filled with specimens to evaluate the mechanical behavior as a function of location and orientation. Variations in the mechanical properties are likely due to recoater blade interactions with the powder and uneven gas flow. The results obtained in this study are analyzed to assess the reliability and reproducibility of the process. A different build evaluates the performance of near-net-shaped tensile specimens angled 35°-90° from the build plate surface (horizontal). Ductility measurements and surface roughness vary significantly as a function of the build angle. In the stress-relieved and as-built conditions, the mechanical behavior of vertically oriented specimens exhibits somewhat lower and more variable ductility than horizontally oriented specimens. Therefore, several process variables affect the mechanical properties of parts produced by the L-PBF process.

36 MATERIALS SCIENCE↗

Effect of Cerium Oxide on Morphologies and Electrochemical Properties of Ni-W-P Coating on AZ91D Magnesium

AZ91D magnesium alloy substrate was first pretreated in a phosphoric acid to obtain a phosphate coating, and then, the electroless ternary Ni-W-P coating was deposited using a sulfate nickel bath. The morphologies of the Ni-W-P coating were observed by using scanning electron microscope, the deposition rate of the coating was examined with the method of gravimetric analysis, and the phase analysis was identified by x-ray diffractometer. Electrochemical property was tested by means of an electrochemical analyzer. The results indicated that the addition of an optimum concentration of CeO{sub 2} (cerium oxide) particles could evidently improve the deposition rate and the stability of the plating bath. However, it acted as an inhibiting effect as the concentration of CeO{sub 2} particles exceeded to 8 mg/L in the sulfate nickel bath. The results also revealed that the morphology of Ni-W-P coating became more smooth, compact and uniform with the increase in the concentrations of CeO{sub 2} particles in the bath, but the corrosion resistance decreased due to the precipitation of crystal phases (Ni{sub 3}P, Ni{sub 4}W, etc.) after heat treatment.

36 MATERIALS SCIENCE↗

Heat-Treated TiO{sub 2} Plasma Spray Deposition for Bioactivity Improvement in Ti-6Al-4V Alloy

In the present study, titanium di-oxide (TiO{sub 2}) coating has been developed on Ti-6Al-4V substrate by plasma spray deposition. Followed by plasma spraying, heat treatment of the sprayed sample has been carried out by isothermally holding it at 823 K (550 °C) for 2 h. Microstructural analysis shows the presence of porosity and unmelted particles on the as-sprayed surface, the area fraction of which reduces after heat treatment. X-ray diffraction analysis shows the phase transformation from anatase (in precursor powder) to rutile (in as-sprayed coating and the same after heat treatment). There is an improvement in nano-hardness, “Young’s modulus” and wear resistance in plasma-sprayed TiO{sub 2} coating (as-sprayed as well as post-heat-treated condition) as compared to as-received Ti-6Al-4V, though post-heat treatment offers a superior hardness, “young’s modulus” and wear resistance as compared to as-sprayed coating. The corrosion behavior in “hank’s solution” shows decrease in corrosion resistance after plasma spraying and post-heat treatment as compared to as-received substrate. A significant decrease in contact angle and improvement in bioactivity (in terms of apatite deposition) were observed in TiO{sub 2}-coated surface as compared to as-received Ti-6Al-4V.

36 MATERIALS SCIENCE↗

Processing of High-Entropy AlCoCr{sub 0.75}Cu{sub 0.5}FeNi Alloy by Spray Forming

Compositionally complex AlCoCrCuFeNi alloy system is one of the extensively studied high-entropy alloys (HEA). Most of these studies have been carried out on as-cast materials that witness slow cooling rate during solidification. In the present investigation, HEA based on AlCoCrCuFeNi system was processed employing spray forming so as to realize its inherent rapid solidification effect and unique microstructural evolution mechanism. The spray formed as well as the as-cast alloys were compared in terms of their microstructural features, phase constitution and hardness. These microstructural features were also compared with that of the overspray powders (< 250 µm) obtained as a by-product of spray forming. Both the as-cast and spray formed alloys showed a mixture of mainly two phases, i.e., face-centered and body-centered cubic (BCC) phases, in contrast to a single BCC phase in overspray powders. However, the spray formed alloy revealed unidentified phases, as against the as-cast material, which disappeared after heat treatment at 1473 K for 3 h. The grain size of the as-cast alloy was around 600-1000 μm compared to a highly refined grain size of 25-30 μm in the as-spray formed alloy. It was found that the hardness of the regions dominated by the constituent phases as well as the bulk of the spray formed material was higher than that of the as-cast alloy. The results validate the efficacy of the process in achieving drastic refinement in grain size, in a single step of large-scale spray forming. The characteristic microstructural features and the phase constitutions have been discussed in light of the prevailing mechanisms of structural evolution and possible solidification phenomena during spray atomization and deposition. This study gives a new direction in processing of these alloys and understanding their solidification behavior under the conditions of layer-by-layer deposition of semi-solid/liquid droplets.

36 MATERIALS SCIENCE↗

In Situ Apparatus to Study Gas–Metal Reactions and Wettability at High Temperatures for Hot-Dip Galvanizing Applications

The understanding of gas–metal reactions and related surface wettability at high temperatures is often limited due to the lack of in situ surface characterization. Ex situ transfers at low temperature between annealing furnace, wettability device, and analytical tools induce noticeable changes of surface composition distinct from the reality of the phenomena.Therefore, a high temperature wettability device was designed in order to allow in situ sample surface characterization by x-rays photoelectron spectroscopy after gas/metal and liquid metal/solid metal surface reactions. Such airless characterization rules out any contamination and oxidation of surfaces and reveals their real composition after heat treatment and chemical reaction. The device consists of two connected reactors, respectively, dedicated to annealing treatments and wettability measurements. Heat treatments are performed in an infrared lamp furnace in a well-controlled atmosphere conditions designed to reproduce gas–metal reactions occurring during the industrial recrystallization annealing of steels. Wetting experiments are carried out in dispensed drop configuration with the precise control of the deposited droplets kinetic energies. The spreading of drops is followed by a high-speed CCD video camera at 500-2000 frames/s in order to reach information at very low contact time. First trials have started to simulate phenomena occurring during recrystallization annealing and hot-dip galvanizing on polished pure Fe and FeAl8 wt.% samples. The results demonstrate real surface chemistry of steel samples after annealing when they are put in contact with liquid zinc alloy bath during hot-dip galvanizing. The wetting results are compared to literature data and coupled with the characterization of interfacial layers by FEG-Auger. It is fair to conclude that the results show the real interest of such in situ experimental setup for interfacial chemistry studies.

36 MATERIALS SCIENCE↗

Cu-7Cr-0.1Ag Microcomposites Optimized for High Strength and High Condutivity

This paper (i) investigated how the microstructure, conductivity, and mechanical properties of Cu-7Cr-0.1Ag microcomposites were changed by cold drawing and subsequent heat treatment, and (ii) produced the Cu-7Cr-0.1Ag microcomposite with an optimum combination of strength and conductivity. The figure of merit Z (combining strength and conductivity) of the Cu-7Cr-0.1Ag microcomposite was larger than that of the microcomposite without silver for each heat treatment. The value of Z of the Cu-7Cr-0.1Ag microcomposite was a maximum after heat treatment for 1 h at 600 °C, indicating that this was the optimum intermediate heat treatment. The following combinations of conductivity, strength and ductility (measured as elongation to fracture) were obtained by the Cu-7Cr-0.1Ag microcomposite with η = 8: (i) 77.9% IACS (International Annealed Copper Standard), 920 MPa and 3.1%; (ii) 79.3% IACS, 880 MPa and 3.3%; and (iii) 79.9% IACS, 798 MPa and 3.5%. These values for the Cu-7Cr-0.1Ag microcomposite were larger than those of the Cu-7Cr microcomposite.

36 MATERIALS SCIENCE↗

Effect of Heat Treatment on the Properties of CoCrMo Alloy Manufactured by Selective Laser Melting

To obtain medical implants with better mechanical properties, it is necessary to conduct studies on the heat treatment process of the selective laser melting (SLM) manufacturing parts. The differential scanning calorimetry method was used to study the heat treatment process of the phase transition of SLM CoCrMo alloy parts. The tensile properties were tested with a tensile test machine, the quantity of carbide precipitated after heat treatment was measured by energy-dispersive x-ray spectroscopy, and the tensile fracture morphology of the parts was investigated using SEM. The obtained results were: Mechanical properties in terms of elongation and tensile strength of CoCrMo alloy manufactured by SLM that had been heat-treated at 1200 °C for 2 h followed by cooling with water were not only higher than the national standard but also higher than the experimental results of the same batch of castings. The mechanism of fracture of parts manufactured by SLM without heat treatment was brittle fracture, whereas parts which had been heat-treated at 1200 °C for 2 h combined with water cooling and at 1200 °C for 1 h with furnace cooling suffered ductile fracture. This study provides the basis for defining the applications for which CoCrMo alloys manufactured by SLM are suitable within the field of medical implants.

36 MATERIALS SCIENCE↗

The Effect of Heat Treatment Process Parameters on Mechanical Properties, Precipitation, Fatigue Life, and Fracture Mode of an Austenitic Mn Hadfield Steel

In this study, the effect of cooling rate after heat treatment on mechanical properties, fatigue life, precipitation and fracture mode of an austenitic Mn Hadfield steel was investigated. Cast samples of the Hadfield steel were heat treated at 1100 C for 2 h. The samples were subsequently quenched in pure water and also in 3 wt.% NaCl salt bath. Optical microscope (OM) and scanning electron microscope (SEM) were used to analyze microstructure and fracture surfaces. Transmission electron microscope (TEM) was used to assess the precipitates. X-ray diffraction (XRD) was used to determine the phases formed. Mechanical properties and fatigue life were determined by uniaxial tensile test, bending fatigue and hardness measurements. Results showed that the sample quenched in salt bath had lower Mn{sub 3}C precipitates, hardness, yield and tensile strengths. Instead, this situation resulted in a more ductile fracture mode and higher formability. Finally, the fatigue life of the sample quenched in salt bath was longer than the one quenched in pure water.

36 MATERIALS SCIENCE↗

Stochastically estimated covariance matrices for independent and cumulative fission yields in the ENDF/B-VIII.0 and JEFF-3.3 evaluations

A Monte-Carlo method for the generation of correlation and covariance matrices for independent and cumulative fission yields has been developed. The method uses a constrained Monte-Carlo resampling structure in order to vary evaluated fission yield libraries in a way that meets basic conservation principles. This results in the generation of correlation/covariance matrices with limited model bias and uncertainty; the matrices are primarily reflective of the evaluated fission yield uncertainties and correlations that arise from the evaluation process. This method has been applied to generate correlation and covariance matrices for all of the fissioning systems of the ENDF/B-VIII.0 and JEFF-3.3 evaluations, marking the first time such matrices have been generated for all of these systems. These covariance matrices have been published online for immediate public use. These correlation and covariance matrices can be used to improve uncertainty estimation in calculations of reactor antineutrino emission rates, decay heat problems, and nuclear forensics.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Evolution of thermo-mechanical properties of concrete with calcium aluminate cement and special aggregates for energy storage

Highlights: • CAC Concrete with stable aggregates is suitable for high temperatures with cycles. • Concrete suffered performance changes after the first thermal cycle (dehydration). • Subsequent thermal cycles showed stabilization and slight performance decreases. With the ever-expanding presence of solar energy, the design of cost-efficient heat energy storage systems is becoming increasingly relevant. Concrete is a potential solid material for these systems but raises questions of its response at high temperatures in operating conditions. This work studies concrete designed with calcium aluminate cement and three types of aggregates that are stable at high temperatures. The designed concrete mixes were exposed to thermal cycles (290–550 °C), and their thermal fatigue response was evaluated with mechanical, cracking, thermal, and microstructural analyses at room temperature after heat cycles. The obtained results show that the main changes are mostly produced after the first thermal cycle and are stabilized during successive thermal cycles, with only a slight decrease in the thermo-mechanical properties. The results showed stabilization of cracking, crack widths between 10 and 80 μm, reduction of compressive strength, around 50–65%, and reduction of the thermal conductivity by 30%.

36 MATERIALS SCIENCE↗

Investigations on microstructure, mechanical properties and abrasion resistance of 4wt%Cr-2wt%Mn-2wt%Cu-Fe-B alloy

Highlights: • The microstructure mainly consists of martensite and boride (M{sub 2}B) in the as-cast and heat treated Fe-B alloys, and the M{sub 2}B presents 3D-skeleton continuous-distribution. • After heat treatment, the nucleation and precipitation of secondary borocarbide M{sub 23}(C, B){sub 6} probably take place in an in situ manner within martensite. • The matrix hardness and bulk hardness of Fe-B alloy decrease after heat treatment, this is attributed to the decreasing of B/C concentration of matrix caused by the precipitation of M{sub 23}(C, B){sub 6}. • During the two-body wear process, the wear mechanism of Fe-B alloy is microcutting; with decreasing of hardness of Fe-B alloy, the abrasion resistance of Fe-B alloy decreases, i.e. the heat treatment will decrease the abrasion resistance of Fe-B alloy. - Abstract: The microstructure, mechanical properties and abrasion resistance of Fe-B alloy with 4wt%Cr-2wt%Mn-2wt%Cu addition have been systematically investigated. The results show that the microstructures mainly consist of martensite and boride (M{sub 2}B) in the as-cast and heat treated Fe-B alloys; after heat treatment, the morphology and volume fraction of the M{sub 2}B have little change, meanwhile the nucleation and precipitation of secondary borocarbide M{sub 23}(C, B){sub 6} probably take place in an in situ manner within martensite. Moreover, the M{sub 2}B is identified as chemical formula of Fe{sub 2.04}Cr{sub 0.11}Mn{sub 0.07}(B, C) reflecting body-centred tetragonal (bct) structure, and the secondary borocarbide M{sub 23}(B, C){sub 6} has the stoichiometry of Fe{sub 18.84}Cr{sub 2.84}Mn{sub 0.57}(B, C){sub 6} with face-centred cubic (fcc) structure. After heat treatment, the matrix hardness and bulk hardness of Fe-B alloy decrease owing to the decreasing of B/C concentration of matrix caused by the precipitation of M{sub 23}(C, B){sub 6}, while the fracture toughness of Fe-B alloy increases. Meanwhile, the heat treatment will decrease the wear resistance of Fe-B alloy, i.e. the wear resistance of Fe-B alloy would decrease with reduction of the matrix hardness.

36 MATERIALS SCIENCE↗

Microstructure, precipitates and hardness of selectively laser melted AlSi10Mg alloy before and after heat treatment

Highlights: • Microstructural characterization of SLM AlSi10Mg alloy and comparison with cast and powder AlSi10Mg • Effect of solution heat treatment and aging on the hardness change of SLM AlSi10Mg alloy • Evolution of strengthening precipitates and Fe-rich intermetallics in SLM AlSi10Mg during heat treatment - Abstract: The microstructure and precipitates within selectively laser melted (SLM) AlSi10Mg alloys in the as-built state and after T6 heat treatment were examined and correlated to the hardness evolution. The as-built alloy exhibited columnar patterns perpendicular to the build-direction and fish-scale pattern along the build-direction originating from the melt pool. The microstructure consisted of fine Al cells and eutectic structure with up to 4 μm in size. Tiny needle-like Si particles with highly faulted structure were identified within the Al cells and formed semi-coherent interface with the matrix. Nanoscale Si particles and π-Al{sub 8}Si{sub 6}Mg{sub 3}Fe phase were observed to segregate along the cell and grain boundary. Solution heat treatment (SHT) at 520 °C resulted in the dissolution of Al cellular microstructure. Precipitation and coarsening of the Si particles occurred, while the aspect ratio of Si particles remained nearly constant. The π-Al{sub 8}Si{sub 6}Mg{sub 3}Fe phase decomposed into plate-shaped β-Al{sub 5}SiFe. The artificial aging (AA) at 160 °C did not alter the microstructure but led to the formation of metastable Mg{sub 2}Si precipitates. The GP zones and β″ were identified through transmission electron microscopy after AA of 6 h, and β″ existed up to AA of 24 h. The hardness decreased after SHT due to the coarsening of the microstructure and reduced solid solution hardening. Hardness reached maximum magnitude after AA of 6–10 h due to the precipitation hardening, and remained relatively unchanged up to AA of 24 h. Microstructure and/or hardness of gas atomized powders and bulk cast AlSi10Mg alloys were also examined as references.

36 MATERIALS SCIENCE↗

Modification of eutectic Mg2Si in AlMg5Si2Mn alloy by pre-homogenization deformation treatment with different reduction conditions

Highlights: • PHD treatment was proposed to modify Mg{sub 2}Si morphology of extruded AlMg5Si2Mn alloy. • PHD treatment accelerated spheroidization of eutectic Mg{sub 2}Si in AlMg5Si2Mn alloy. • Tensile properties of AlMg5Si2Mn extrudates were improved by introduction of PHD. - Abstract: The effect of a novel pre-homogenization deformation (PHD) treatment on the microstructure and mechanical properties of extruded AlMg5Si2Mn alloy was investigated. By introducing the cold compression prior to homogenization treatment, the brittle and interconnected eutectic Mg{sub 2}Si phase in the as-cast AlMg5Si2Mn alloy transformed into fine and spherical particles uniformly dispersed in the aluminum matrix. As the amount of PHD increased, up to 10%, the size of the Mg{sub 2}Si particles decreased and their sphericity increased in the extruded samples, resulting in a gradual increase in both strength and elongation after heat treatment. The mechanical properties of the PHD-treated AlMg5Si2Mn extrudates were compared with those of materials prepared using various casting and deformation processes, and the potential application to wrought products was discussed.

36 MATERIALS SCIENCE↗

Fine grained fully lamellar structure acquisition and microstructure characteristics of Ti-44Al-4Nb-4V-0.3Mo-Y alloy

Highlights: • Cellular structure is the component of the microstructure of hot forging in α + β two-phase-field. • Inhomogeneous lamellar structure could be eliminated by hot forging in β+γ binary phase field. • After hot forging and annealing at β+γ two-phase-region, fine grained fully-lamellar microstructure is obtained. - Abstract: In this paper, the microstructure characteristic of a β solidifying TiAl alloy Ti-44Al-4Nb-4V-0.3Mo-Y (at. %) was investigated systematically. Cylindrical blanks were isothermal forged at 1250 °C within (α + β) two-phase-field and 1200 °C within (β + γ) two-phase-field under the strain rate of 0.02 s{sup −1} and 0.03 s{sup −1}, with a total reduction of 75%. The microstructure of the alloy forged in α + β two-phase-field consists of lamellar colonies (only represents α{sub 2}/γ lamellar colonies), mixture structure of β/B2 phase and γ phase as well as β/γ lamellae resulted from cellular reaction. However, a large amount of equiaxed γ grains appear with no β/γ lamellae available under forging in β + γ two-phase-field, and the average size of γ grain is about 10 μm. By further annealed at 900 °C for about 0.5 h, the structure of hot forging at 1250 °C is composed of β/B2 phase and equiaxed γ grains with the mean size about 5 μm. After heat treated at 1200 °C for 2 h, the microstructure of this annealed samples is characterized by fine grained fully lamellar (FFL) structure with size of 20 μm. A specially designed hot forging process is proposed, which prevents the existence of inhomogeneous lamellar structure.

36 MATERIALS SCIENCE↗

Heat shock induces the nuclear accumulation of YAP1 via SRC

Highlights: • YAP1 enters the nucleus in response to heat shock. • YAP1 spontaneously returns to the cytoplasm after heat shock. • SRC is involved in the nuclear accumulation of YAP1. • HSP90 is involved in the return to the cytoplasm of YAP1. • YAP1 cross-talks with NF-κB signaling in response to heat shock. Yes-associated protein 1 (YAP1), a co-transcription activator, shuttles between the cytoplasm and the nucleus. Phosphorylation by large tumor suppressor kinases (LATS1/2) is the major determinant of YAP1 subcellular localization. Unphosphorylated YAP1 interacts with transcription factors in the nucleus and regulates gene transcription, while phosphorylated YAP1 is trapped in the cytoplasm and is degraded. We found that when U2OS and HeLa cells are exposed to 42 °C, YAP1 enters the nucleus within 30 min and returns to the cytoplasm at 4 h. SRC and HSP90 are involved in nuclear accumulation and return to the cytoplasm, respectively. Upon heat shock, LATS2 forms aggregates including protein phosphatase 1 and is dephosphorylated and inactivated. SRC activation is necessary for the formation of aggregates, while HSP90 is required for their dissociation. YAP1 is involved in heat shock-induced NF-κB signaling. Mechanistically, YAP1 is implicated in strengthening the interaction between RELA and DPF3, a component of SWI/SNF chromatin remodeling complex, in response to heat shock. Thus, YAP1 plays a role as a thermosensor.

60 APPLIED LIFE SCIENCES↗

Specificities of Local Dynamics and Orientational State of Rigid-Chain Liquid-Crystal Polymers

Proton magnetic resonance (PMR) spectra and terahertz IR spectra of Vectra A950 fibers and granules and Armos fibers before and after heat treatment were obtained and analyzed in order to understand the molecular mobility mechanisms that ensure the self-organization and restructurization of these rigid-chain liquid-crystal polymers, as well as their similarity and difference. It is shown that large-scale thermal (quasi-segmental) mobility in such LC polymers is due to the reptation of macromolecules with respect to each other and the conformational transitions necessary for the motion of chains in them are the result of random accumulation of displacements that occur during local bending and torsional-vibrational movements in the links of polymer chains according to the Bresler–Frenkel mechanism.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗