Search NASA⌕ Search

SEARCH · Search NASA

Results for “AFTERBURNER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Experimental evaluation of a TF30-P-3 turbofan engine in an altitude facility: Afterburner performance and engine-afterburner operating limits

For distortion free steady state operation at the maximum (full afterburning) throttle position, the afterburner combustion efficiency decreased from 0.91 to 0.68 as engine inlet Reynolds number index was reduced from 0.80 to 0.25. Engine afterburner operational limits were obtained for transient and fixed throttle operation over a range of engine inlet distortions. At limiting conditions, time histories of pressures in the fan compressor during throttle transients between military and maximum showed the development of rotating stall in the fan hub which quickly propagated and produced complete stall in the high pressure compressor.

Mcaulay, J. E.↗
NASA NTRS1955

Altitude Performance of Modified J71 Afterburner with Revised Engine Operating Conditions

An investigation was conducted in an altitude test chamber at the NACA Lewis laboratory to determine the effect of a revision of the rated engine operating conditions and modifications to the afterburner fue1 system, flameholder, and shell cooling on the augmented performance of the J71-A-2 (x-29) turbo jet engine operating at altitude . The afterburner modifications were made by the manufacturer to improve the endurance at sea-level, high-pressure conditions and to reduce the afterburner shell temperatures. The engine operating conditions of rated rotational speed and turbine-outlet gas temperature were increased. Data were obtained at conditions simulating flight at a Mach number of 0.9 and at altitudes from 40,000 to 60,000 feet. The afterburner modifications caused a reduction in afterburner combustion efficiency. The increase in rated engine speed and turbine-outlet temperature coupled with the afterburner modifications resulted in the over-all thrust of the engine and afterburner being unchanged at a given afterburner equivalence ratio, while the specific fuel consumption was increased slightly. A moderate shift in the range of equivalence ratios over which the afterburner would operate was encountered, but the maximum operable altitude remained unaltered. The afterburner-shell temperatures were also slightly reduced because of the modifications to the afterburner.

Useller, James W.↗
NASA NTRS1953

Altitude Starting Characteristics of an Afterburner with Autoignition and Hot-streak Ignition

An investigation was conducted in an altitude test chamber at the NACA Lewis Laboratory to determine the altitude starting characteristics of an afterburner with autoignition and with hot-streak ignition. Transient afterburner ignition data were obtained over a range of altitudes from 30,000 to 50,000 feet at a flight Mach number of 0.60. Afterburner ignition with a torch igniter located axially at approximately the midpoint of the combustion chamber was possible over the entire range, but ignition ignition with a torch igniter located in the transition section 1 5/8 inches upstream of the turbine stators proved unsatisfactory at an altitude of 50,000 feet due to the inability to obtain flame through the turbine. Increasing the afterburner-inlet total pressure at a constant afterburner fuel-air ratio decreased the afterburner ignition time. Hot-streak ignition was possible within 2 seconds after the time required to obtain the preset, normal afterburner fuel pressure, whereas autoignition required 4 to 7 seconds for the range of altitudes investigated. Following the ignition there was a period of oscillatory operation existing in the engine-afterburner before steady-state operation was attained. The time required for steady-state stable operation decreased as afterburner inlet total pressure increased. The duration of oscillations also decreased with hot-streak ignition because the fuel-air mixture was ignited before a large volume of combustible mixture was accumulated in the afterburner.

Engines, Control - Turbojet↗
NASA NTRS1958

Altitude Performance of the Afterburner on the Iroquois Turbojet Engine. Coord. No. AF-P-6

The performance and operational characteristics of two afterburner configurations for the Iroquois turbojet engine were evaluated in an altitude test chamber over a range of afterburner equivalence ratios at afterburner-inlet pressures from 733 to 3186 pounds per square foot absolute. These conditions correspond to an altitude range from 38,700 to 66,800 feet at a flight Mach number of 1.5. The only difference between the two afterburner configurations was in the pattern of afterburner fuel injection. At an afterburner-inlet pressure of approximately 3100 pounds per square foot absolute, corresponding to an altitude of 38,700 feet and a_ flight Mach number of 1.5, the combustion efficiency of both configurations reached peak values of 0.80 to 0.85 at equivalence ratios of 0.35 to 0.40. However, further reduction in the afterburner-inlet pressure severely affected combustion efficiency. For example, at an afterburner inlet pressure level of 700 to 1000 pounds per square foot absolute, the efficiency for both configurations was 0.20 to 0.40.

Groesbeck, Donald E.↗
NASA NTRS1956

Effect of Operating Conditions and Design on Afterburner Performance

Afterburners for turbojet engines have, within the past decade, found increasing application in service aircraft. Practically all engines manufactured today are equipped with some form of afterburner, and its use has increased from what was originally a short-period thrust-augmentation application to an essential feature of the turbojet propulsion system for flight at supersonic speeds. The design of these afterburners has been based on extensive research and development effort in expanded laboratory facilities by both the NACA and the American engine industry. Most of the work of the engine industry, however, has either not been published or is not generally available owing to its proprietary nature. Consequently, the main bulk of research information available for summary and discussion is of NACA origin. However, because industrial afterburner development has closely followed NACA research, the omission is more one of technical detail than method or concept. One principal difficulty encountered in summarizing the work in this field is that sufficient knowledge does not yet exist to rationally or directly integrate the available background of basic combustion principles into combustor design. A further difficulty is that most of the experimental investigations that have been conducted were directed chiefly toward the development of specific afterburners for various engines rather than to the accumulation of systematic data. This work has, nonetheless, provided not only substantial improvements in the performance of afterburners but also a large fund of experimental data and an extensive background of experience in the field. Consequently, it is the purpose of the present chapter to summarize the many, and frequently unrelated, experimental investigations that have been conducted rather than to formulate a set of design rules. In the treatment of this material an effort has been made, however, to convey to the reader the "know how" acquired by research engineers in the course of afterburner studies.

Fleming, W. A.↗
NASA NTRS1976

Exhaust emission calibration of two J-58 afterburning turbojet engines at simulated high-altitude, supersonic flight conditions

Emissions of total oxides of nitrogen, nitric oxide, unburned hydrocarbons, carbon monoxide, and carbon dioxide from two J-58 afterburning turbojet engines at simulated high-altitude flight conditions are reported. Test conditions included flight speeds from Mach 2 to 3 at altitudes from 16.0 to 23.5 km. For each flight condition exhaust measurements were made for four or five power levels, from maximum power without afterburning through maximum afterburning. The data show that exhaust emissions vary with flight speed, altitude, power level, and radial position across the exhaust. Oxides of nitrogen emissions decreased with increasing altitude and increased with increasing flight speed. Oxides of nitrogen emission indices with afterburning were less than half the value without afterburning. Carbon monoxide and hydrocarbon emissions increased with increasing altitude and decreased with increasing flight speed. Emissions of these species were substantially higher with afterburning than without.

Holdeman, J. D.↗
NASA NTRS1973

Measurement of gaseous emissions from an afterburning turbojet engine at simulated altitude conditions

Gaseous emissions from a J85-GE-13 turbojet engine were measured over a range of fuel-air ratios from idle to full afterburning and simulated altitudes from near sea-level to 12,800 meters (42,000 ft). Without afterburning, carbon monoxide and unburned hydrocarbon emissions were highest at idle and lowest at takeoff; oxides of nitrogen exhibited the reverse trend. With afterburning, carbon monoxide and unburned hydrocarbon emissions were greater than for military power. Carbon monoxide emissions were altitude dependent. Oxides of nitrogen emissions were less at minimum afterburning than at military power. For power levels above minimum afterburning, the oxides of nitrogen emissions were both power level and altitude dependent.

Diehl, L. A.↗
NASA NTRS1954

Investigation of Noise Field and Velocity Profiles of an Afterburning Engine

Sound pressure levels, frequency spectrum, and jet velocity profiles are presented for an engine-afterburner combination at various values of afterburner fuel - air ratio. At the high fuel-air ratios, severe low-frequency resonance was encountered which represented more than half the total energy in the sound spectrum. At similar thrust conditions, lower sound pressure levels were obtained from a current fighter air craft with a different afterburner configuration. The lower sound pressure levels are attributed to resonance-free afterburner operation and thereby indicate the importance of acoustic considerations in afterburner design.

North, Warren J.↗
NASA NTRS1956

Investigation of Afterburner Combustion Screech and Methods of Its Control at High Combustor Pressure Levels

Various methods for the control of afterburner combustion screech at afterburner-inlet total pressures of from 4000 to 6400 pounds per square foot absolute were investigated experimentally. In general, the range of afterburner fuel- air ratios in which screech occurred and the intensity of screech did not vary appreciably in the range of pressures covered. However, several configurations which had mild screech tendencies at the lower pressures were screech-free, or nearly so, at higher pressure levels. Screech was successfully eliminated over the range of pressures and fuel- air ratios investigated by several devices including a 20- inch length of corrugated louvered liner at the afterburner wall, a 7-inch perforated shroud around the outer ring of a 2-ring V- gutter flame holder, and a 2- ring V- gutter flame holder fabricated from perforated sheet metal. A 20-inch length of cylindrical liner spaced 5/8 inch from the afterburner wall and perforated with 3/16- inch- diameter holes on 1/2- inch centers did not entirely eliminate screech, but a 36- inch length of the same material did.

Arthur M. Trout↗
NASA NTRS1956

Simulated afterburner performance with hydrogen peroxide injection for thrust augmentation

Combustion performance of three afterburner configurations was evaluated at simulated altitude flight conditions with liquid augmentation to the primary combustor. Afterburner combustion efficiency and stability were better with injection of high-strength hydrogen peroxide than with no injection or with water injection. Improvements were observed in afterburner configurations with and without flameholders and in a short-length afterburner. At a peroxide-air ratio of 0.3, combustion was stable and 85 to 90 percent efficient in all configurations tested. Calculated augmented net-thrust ratios for peroxide injection with afterburning were approximately 60 percent greater than those for water injection.

Metzler, Allen J↗
NASA NTRS2015

Surface Temperature Measurements from a Stator Vane Doublet in a Turbine Engine Afterburner Flame Using a YAG:Tm Thermographic Phosphor

Luminescence-based surface temperature measurements were obtained from a YAG:Tm-coated stator vane doublet exposed to the afterburner flame of a J85 test engine at University of Tennessee Space Institute (UTSI). The objective of the testing was to demonstrate that reliable surface temperatures based on luminescence decay of a thermographic phosphor producing short-wavelength emission could be obtained from the surface of an actual engine component in a high gas velocity, highly radiative afterburner flame environment. YAG:Tm was selected as the thermographic phosphor for its blue emission at 456 nm (1D23F4 transition) and UV emission at 365 nm (1D23H6 transition) because background thermal radiation is lower at these wavelengths, which are shorter than those of many previously used thermographic phosphors. Luminescence decay measurements were acquired using a probe designed to operate in the afterburner flame environment. The probe was mounted on the sidewall of a high-pressure turbine vane doublet from a Honeywell TECH7000 turbine engine coated with a standard electron-beam physical vapor deposited (EB-PVD) 200-m-thick TBC composed of yttria-stabilized zirconia (YSZ) onto which a 25-m-thick YAG:Tm thermographic phosphor layer was deposited by solution precursor plasma spray (SPPS). Spot temperature measurements were obtained by measuring luminescence decay times at different afterburner power settings and then converting decay time to temperature via calibration curves. Temperature measurements using the decays of the 456 and 365 nm emissions are compared. While successful afterburner environment measurements were obtained to about 1300C with the 456 nm emission, successful temperature measurements using the 365 nm emission were limited to about 1100C due to interference by autofluorescence of probe optics at short decay times.

thermographic phosphor↗
NASA NTRS1975

Effect of afterburner lights and inlet unstarts on a mixed compression inlet turbofan engine operating at Mach 2.5

Data are presented to show the response of an uncontrolled inlet to afterburner lightoff disturbances when a mixed-compression inlet is coupled to a turbofan engine. The results show a significant upstream shock excursion when the afterburner lights which is a result of the direct communication between the afterburner region and the inlet by means of the fan duct and fan stages. In addition results of a waveform analysis on the inlet pressure response to the afterburner light is presented. Inlet unstarts and their effect on operation of the propulsion system is also discussed.

Baumbick, R. J.↗
NASA NTRS1977

Altitude test of several afterburner configurations on a turbofan engine with a hydrogen heater to simulate an elevated turbine discharge temperature

A performance test of several experimental afterburner configurations was conducted with a mixed-flow turbofan engine in an altitude facility. The simulated flight conditions were for Mach 1.4 at two altitudes, 12,190 and 14,630 meters. Turbine discharge temperatures of 889 and 1056 K were used. A production afterburner was tested for comparison. The research afterburners included partial forced mixers with V-gutter flameholders, a carburetted V-gutter flameholder, and a triple ring V-gutter flameholder with four swirl-can fuel mixers. Fuel injection variations were included. Performance data shown include augmented thrust ratio, thrust specific fuel consumption, combustion efficiency, and total pressure drop across the afterburner.

Johnsen, R. L.↗
NASA NTRS1981

Exhaust emission survey of an F100 afterburning turbofan engine at simulated altitude flight conditions

Emissions of carbon monoxide, total oxides of nitrogen, unburned hydrocarbons, and carbon dioxide from an F100, afterburning, two spool turbofan engine at simulated flight conditions are reported. For each flight condition emission measurements were made for two or three power levels from intermediate power (nonafterburning) through maximum afterburning. The data showed that emissions vary with flight speed, altitude, power level, and radial position across the nozzle. Carbon monoxide emissions were low for intermediate power (nonafterburning) and partial afterburning, but regions of high carbon monoxide were present downstream of the flame holder at maximum afterburning. Unburned hydrocarbon emissions were low for most of the simulated flight conditions. The local NOX concentrations and their variability with power level increased with increasing flight Mach number at constant altitude, and decreased with increasing altitude at constant Mach number. Carbon dioxide emissions were proportional to local fuel air ratio for all conditions.

Moss, J. E.↗