Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIR BLAST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Gas and drop behavior in reacting and non-reacting air-blast atomizer sprays

A detailed study of the two-phase flow produced by a gas-turbine air-blast atomizer is performed with the goal of identifying the interaction between the two phases for both nonreacting and reacting conditions. A two-component phase Doppler interferometry is utilized to characterize three flowfields produced by the atomizer: (1) the single-phase flow, (2) the two-phase nonreacting spray, and (3) the two-phase reacting spray. Measurements of the mean and fluctuating axial and azimuthal velocities for each phase are obtained. In addition, the droplet size distribution, volume flux, and concentration are measured. The results reveal the strong influence of the dispersed phase on the gas, and the influence of reaction on both the gas and the droplet field. The presence of the spray significantly alters the inlet condition of the atomizer. With this alteration quantified, it is possible to deduce that the inertia associated with the dispersed phase damps the fluctuating velocities of the gas. Reaction reduces the volume flux of the droplets, broadens the local volume distribution of the droplets in the region of the reaction zone, increases the axial velocities and radial spread of the gas, and increases the anisotropy in the region of the reaction zone.

Mcdonell, Vincent G.↗
NASA NTRS1955

Preliminary Data on Rain Deflection from Aircraft Windshields by Means of High-Velocity Jet-Air Blast

A preliminary experimental investigation is being conducted to determine the feasibility of preventing rain from impinging on aircraft windshields by means of high-velocity jet-air blast. The results indicate that rain deflection by jet blast appears feasible for flight speeds comparable with landing and take-off speeds of interceptor-type jet aircraft; however, attainment of good visibility through the mist generated by raindrop breakup presents a problem. For the simulated windshield and the lower windshield angles used in the investigation, air-flow rates of the order of 3.3 pounds per minute of unheated air per inch of windshield span were required for adequate rain deflection at a free-stream velocity of 135 miles per hour. A method has been devised whereby it is possible to produce large-diameter water drops (1000 to 1500 p.) in a moving air stream, without breakup, at speeds in excess of 175 miles per hour.

Ruggeri, Robert S.↗
DOE OSTI2020

A numerical study of particle jetting in a dense particle bed driven by an air-blast

In this work, the particle jetting behavior in a blast-driven dense particle bed is studied at early times. Four-way coupled Euler–Lagrange simulations are performed using a high-order discontinuous Galerkin spectral element solver coupled with a high-order Lagrangian particle solver, wherein the inter-particle collisions are resolved using a discrete element method collision model. Following the experiments of Rodriguez et al. [“Formation of particle jetting in a cylindrical shock tube,” Shock Waves 23(6), 619–634 (2013)] and the simulations of Osnes et al. [“Numerical simulation of particle jet formation induced by shock wave acceleration in a Hele-Shaw cell,” Shock Waves 28(3), 451–461 (2018)], the simulations are performed in a quasi-two-dimensional cylindrical geometry (Hele-Shaw cell). Parametric studies are carried out to assess the impact of the coefficient of restitution and the strength of the incident shock on the particle jetting behavior. The deposition of vorticity through a multiphase (gas–particle) analog of Richtmyer–Meshkov instability is observed to play a crucial role in channeling the particles into well-defined jets at the outer edge of the particle bed. This is confirmed by the presence of vortex pairs around the outer jets. Furthermore, the effect of the relaxation of the relative velocity between the two phases on the vorticity generation is explored by analyzing the correlation between the radial velocity of particles and the radial velocity of the gas at the particle location.

42 ENGINEERING↗
DOE OSTI2023

Numerical Modeling of Air-Blast Suppression as a Function of Explosive-Charge Burial Depth

As a chemical explosion is buried, the mechanism for acoustic wave generation transitions from fully gas-generated at the surface to completely spall-induced at full containment depth. The fully gas-generated and completely spall-induced signals in the acoustic waveform are well described; however, the transition between these two end-members eludes numerical modeling because of the complex phenomena that are involved. The phenomena of crater formation and explosive cloud evolution are simulated using an Eulerian hydrocode that incorporates geomaterials with strength and porosity. Having accurately modeled these phenomena, we can confidently predict the propagation and relative strength of the gas-generated and spall-induced pulses in the recorded acoustic waveform. The numerical predictions agree with observations from the historical Stagecoach experiment as well as modern recordings from the Source Physics Experiment. In particular, the peak pressure p generated by an explosion is initially due to the gas-generated mechanism and decays with scaled depth of burial d s (depth d scaled by the cube-root of explosive yield w 1/3 ) as exp(-d s ) but then transitions near a scaled depth of 6 m/ton 1/3 to the spall-generated mechanism in which the decay is d$_{s}^{-7/4}$. This decay form is related to the strong ground-motion attenuation relationship that affects spall strength. So these results can improve seismoacoustic inverse models for the explosive source that need to account for the gas-generated and spall-induced signals and their effect on peak pressures and other acoustic signal features.

58 GEOSCIENCES↗
DOE OSTI2021

Air Blast Meshing & Pressure Mapping [Slides]

Project Goals: Mesh sensitivity study – Determine at what mesh density results converge; Build a model that reflects theoretical solutions. Map experimental pressure data onto the surface of the cone – Track rigid body motion. Stresses in conic Body – Observe how the model reacts to stresses different than the ones tested in the mesh sensitivity study.

42 ENGINEERING↗
DOE OSTI2021

Air Blast Mesh Sensitivity and Pressure Mapping Study

Nose cone structural and aerodynamic characteristics are essential for intelligent design of aircraft, spacecraft, and ballistic systems. Finite element analysis can be used to help understand the structural integrity and flight characteristics of different nose cones. A mesh sensitivity study was undertaken for a particular nose cone geometry that was used in tests at LANL facilities in order to confirm the integrity of the meshed geometry. A simple cone that best matched closed-form theoretical solutions was modeled, and received good correlation to the theory. Complexity was then added back to the nose cone. Parameters applied to the simple cone were then implemented in the nose cone geometry giving assurance of accuracy after the geometry was changed. Nose cone results averaged 6.3% error for radial displacement when compared with the theoretical. Hoop stress averaged 6.0% error and meridional stress averaged 5.7% error at the finest mesh level. Meshes showed signs of convergence when compared to all three theoretical solutions. Finally, pressure time-history data from LANL computational fluid dynamics simulations was applied to the surface of the final nose cone geometry. The pressure data was interpolated from pressure gauge locations onto nearby meshed elements, which allowed for FEA software to run simulations on the cone with the pressure data as a loading condition. The pressure mapping resulted in the ability to understand the nose cone’s rigid body motion that in turn can inform design of future nose cones.

42 ENGINEERING↗
NASA NTRS1990

Influence of the continuous and dispersed phases on the symmetry of a gas turbine air-blast atomizer

Current trends in liquid-fueled practical combustion systems are leaving less tolerance for fuel injection deficiencies such as poor spray field symmetry. The present paper evaluates the symmetry of the flowfield produced by a practical airblast atomizer. Specifically, the influence of both the continuous phase and dispersed phase on the spray field symmetry is assessed. In the present case, asymmetry in volume flux is associated principally with disparities in the injection of the dispersed phase, which is manifested by a maldistribution of larger drops. Asymmetries observed in the continuous phase without the dispersed phase are reduced in magnitude by the presence of the dispersed phase, but still contribute to asymmetry in radial spread of the dispersed phase.

Mcdonell, V. G.↗
NASA NTRS1990

Symmetry assessment of an air-blast atomizer spray

This study represents an evaluation of the extent to which conventional and recently introduced modern diagnostics can assess the symmetry of sprays formed by three atomizers of identical design. The conventional diagnostics include sheet-lit photography, patternation, and laser diffraction. The modern diagnostic is laser interferometry (phase Doppler). Symmetry is assessed in ambient conditions for four atomizer orientations, and comparisons are made between the diagnostic techniques. The results demonstrate that conventional and modern diagnostics are consistent in the assessment of symmetry, patternation and phase Doppler are most effective in establishing symmetry of mass flux, and phase Doppler, although more tedious to employ, provides the additional information necessary to establish the sources of detected asymmetries in terms of nonuniformities in droplet velocities, size distributions, volume flux, and concentration.

Mcdonnell, V. G.↗
NASA NTRS1977

Experimental evaluation of premixing-prevaporizing fuel injection concepts for a gas turbine catalytic combustor

Experiments were performed to evolve and evaluate a premixing-prevaporizing fuel system to be used with a catalytic combustor for possible application in an automotive gas turbine. Spatial fuel distribution and degree of vaporization were measured using Jet A fuel. Three types of air blast injectors, an air assist nozzle and a simplex pressure atomizer were tested. Air swirlers with vane angles up to 30 deg were used to improve the spatial fuel distribution. The work was done in a 12-cm (4.75-in.) diameter tubular rig. Test conditions were: a pressure of 0.3 and 0.5 MPa (3 and 5 atm), inlet air temperatures up to 800 K (980 F), velocity of 20 m/sec (66 ft/sec) and fuel-air ratios of 0.01 and 0.025. Uniform spatial fuel distributions that were within plus or minus 10 percent of the mean were obtained. Complete vaporization of the fuel was achieved with air blast configurations at inlet air temperatures of 550 K (530 F) and higher. The total pressure loss was less than 0.5 percent for configurations without air swirlers and less than 1 percent for configurations with a 30 deg vane angle air swirler.

Tacina, R. R.↗
NASA NTRS1981

Effect of fuel injector type on performance and emissions of reverse-flow combustor

The combustion process in a reverse-flow combustor suitable for a small gas turbine engine was investigated to evaluate the effect of fuel injector type on performance and emissions. Fuel injector configurations using pressure-atomizing, spill-flow, air blast, and air-assist techniques were compared and evaluated on the basis of performance obtained in a full-scale experimental combustor operated at inlet conditions corresponding to takeoff, cruise, low power, and idle and typical of a 16:1-pressure-ratio turbine engine. Major differences in combustor performance and emissions characteristics were experienced with each injector type even though the aerodynamic configuration was common to most combustor models. Performance characteristics obtained with the various fuel injector types could not have been predicted from bench-test injector spray characteristics. The effect of the number of operating fuel injectors on performance and emissions is also presented.

Norgren, C. T.↗
NASA NTRS1993

Coaxial airblast atomizers

An experimental investigation was performed to quantify the characteristics of the sprays of coaxial injectors with particular emphasis on those aspects relevant to the performance of rocket engines. Measurements for coaxial air blast atomizers were obtained using air to represent the gaseous stream and water to represent the liquid stream. A wide range of flow conditions were examined for sprays with and without swirl for gaseous streams. The parameters varied include Weber number, gas flow rate, liquid flow rate, swirl, and nozzle geometry. Measurements were made with a phase Doppler velocimeter. Major conclusions of the study focused upon droplet size as a function of Weber number, effect of gas flow rate on atomization and spray spread, effect of nozzle geometry on atomization and spread, effect of swirl on atomization, spread, jet recirculation and breakup, and secondary atomization.

Hardalupas, Y.↗
NASA NTRS1990

Disintegration of liquid sheets

The development, stability, and disintegration of liquid sheets issuing from a two-dimensional air-assisted nozzle is studied. Detailed measurements of mean drop size and velocity are made using a phase Doppler particle analyzer. Without air flow the liquid sheet converges toward the axis as a result of surface tension forces. With airflow a quasi-two-dimensional expanding spray is formed. The air flow causes small variations in sheet thickness to develop into major disturbances with the result that disruption starts before the formation of the main break-up region. In the two-dimensional variable geometry air-blast atomizer, it is shown that the air flow is responsible for the formation of large, ordered, and small chaotic 'cell' structures.

Mansour, Adel↗
NASA NTRS1977

Experimental evaluation of fuel preparation systems for an automotive gas turbine catalytic combustor

Premixing-prevaporizing fuel systems were evaluated for use with a catalytic reactor for possible automotive gas turbine application. Spatial fuel-air distributions, degree of vaporization, pressure drop and air velocity profiles were measured. Three airblast injectors and an air-assist nozzle were tested. Air swirlers were used to improve the spatial fuel-air distribution. The work was done in a 12 cm tubular duct. Test conditions were: a pressure of 0.3 and 0.5 MPa, inlet air temperatures up to 800 K, air velocities of 10 and 20 m/s and fuel-air ratios up to 0.020. The fuel was Jet A. The best results were obtained with an air-blast configuration that used multiple cones to provide high velocity air for atomization and also straightened the inlet airflow. With this configuration, uniform spatial fuel-air distributions were obtained with mixing lengths greater than 17.8 cm. In this length, vaporization of the fuel was 98.5 percent complete at an inlet air temperature of 700 K. The total pressure loss was 1.0 percent with a reference velocity of 20 m/s and 0.25 percent at 10 m/s. The air velocity was uniform across the duct and no autoignition reactions were observed.

Tacina, R. R.↗