Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIR INLETS - CENTRAL, SUPERSONIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1951

Investigation at Mach Number 1.88 of Half of a Conical-spike Diffuser Mounted as a Side Inlet with Boundary-layer Control / H. Fred Goelzer and Edgar M. Cortright, Jr

Experimental investigation was conducted at Mach number 1.88 to determine performance characteristics of half a 50 degree-conical-spike inlet mounted on a flat plate. Initial boundary layer was removed up-stream of inlet by a ram-type scoop of variable height. Initial boundary-layer thickness was also varied. With complete removal of initial boundary layer, total-pressure recovery of approximately 70 percent. Several alternative boundary-layer-removal systems were investigated which decreased the adverse effect of operating the ram scoop sub-critically.

BOUNDARY LAYER CONTROL-INTERNAL AERODYNAMICS↗
NASA NTRS1952

Performance of Air Inlets at Transonic and Low Supersonic Speeds

A general discussion of the air-inlet problem is presented. Recently obtained drag and pressure-recovery data for transonic-type nose, scoop, and wing-root inlets are summarized. Preliminary results concerning the performance of the sharp-edged supersonic-type inlets at transonic and subsonic speeds also are given.

Nichols, Mark R↗
NASA NTRS1971

Application of quadratic optimization to supersonic inlet control

The application of linear stochastic optimal control theory to the design of the control system for the air intake (inlet) of a supersonic air-breathing propulsion system is discussed. The controls must maintain a stable inlet shock position in the presence of random airflow disturbances and prevent inlet unstart. Two different linear time invariant control systems are developed. One is designed to minimize a nonquadratic index, the expected frequency of inlet unstart, and the other is designed to minimize the mean square value of inlet shock motion. The quadratic equivalence principle is used to obtain the best linear controller that minimizes the nonquadratic performance index. The two systems are compared on the basis of unstart prevention, control effort requirements, and sensitivity to parameter variations.

Lehtinen, B.↗
NASA NTRS1972

Application of quadratic optimization to supersonic inlet control.

This paper describes the application of linear stochastic optimal control theory to the design of the control system for the air intake, the inlet, of a supersonic air-breathing propulsion system. The controls must maintain a stable inlet shock position in the presence of random airflow disturbances and prevent inlet unstart. Two different linear time invariant controllers are developed. One is designed to minimize a nonquadratic index, the expected frequency of inlet unstart, and the other is designed to minimize the mean square value of inlet shock motion. The quadratic equivalence principle is used to obtain a linear controller that minimizes the nonquadratic index. The two controllers are compared on the basis of unstart prevention, control effort requirements, and frequency response. It is concluded that while controls designed to minimize unstarts are desirable in that the index minimized is physically meaningful, computation time required is longer than for the minimum mean square shock position approach. The simpler minimum mean square shock position solution produced expected unstart frequency values which were not significantly larger than those of the nonquadratic solution.

Lehtinen, B.↗
NASA NTRS1983

Aerodynamic characteristics of a series of twin-inlet air-breathing missile configurations. 2: Two-dimensional inlets at supersonic speeds

A series of air-breathing missile configurations was investigated to provide a data base for the design of such missiles. The model could be configured with either twin axisymmetric or two dimensional inlets. Three circumferential inlet locations were investigated: 90 deg, 115 deg, and 135 deg from the top center. Two vertical wing locations, as well as wingless configurations, were used. Three tail configurations were formed by locating the tail surfaces either on the inlet fairings or on fairings on the body. The surfaces were used to provide pitch control. Two dimensional inlets with extended compression surfaces, used to improve the angle-of-attack performance of the inlets for wingless configurations, were also investigated. The two dimensional inlet configurations are covered.

Hayes, C.↗
NASA NTRS1952

Experimental Investigation of a Two-dimensional Split-wing Ram-jet Inlet at Mach Number of 3.85

Performance characteristics of a two-dimensional isentropic diffuser have been experimentally determined at a Mach number of 3.85. At zero angle of attack, a maximum total-pressure recovery of 0.41 was obtained with a supercritical mass-flow ratio of 0.95. As a consequence of the twin-duct arrangement of the diffuser, a large discontinuity in pressure recovery and mass flow with a characteristic hysteresis was encountered between critical and subcritical operation. An asymmetric shock pattern with large-scale separation and flow reversal in one of the passages occurred at reduced mass flows. Pressure and force data presented for an angle-of-attack range from zero to 4 degrees.

DIFFUSERS, SUPERSONIC↗
NASA NTRS2005

Development and Characterization Testing of an Air Pulsation Valve for a Pulse Detonation Engine Supersonic Parametric Inlet Test Section

In pulse detonation engines, the potential exists for gas pulses from the combustor to travel upstream and adversely affect the inlet performance of the engine. In order to determine the effect of these high frequency pulses on the inlet performance, an air pulsation valve was developed to provide air pulses downstream of a supersonic parametric inlet test section. The purpose of this report is to document the design and characterization tests that were performed on a pulsation valve that was tested at the NASA Glenn Research Center 1x1 Supersonic Wind Tunnel (SWT) test facility. The high air flow pulsation valve design philosophy and analyses performed are discussed and characterization test results are presented. The pulsation valve model was devised based on the concept of using a free spinning ball valve driven from a variable speed electric motor to generate air flow pulses at preset frequencies. In order to deliver the proper flow rate, the flow port was contoured to maximize flow rate and minimize pressure drop. To obtain sharp pressure spikes the valve flow port was designed to be as narrow as possible to minimize port dwell time.

Tornabene, Robert↗
NASA NTRS1956

Investigation at supersonic and subsonic Mach numbers of auxiliary inlets supplying secondary air flow to ejector exhaust nozzles

The results indicated increases in auxiliary-inlet pressure recovery with increases in scoop height relative to the boundary-layer thickness. The pressure recovery increased at about the same rate as theoretically predicted for an inlet in a boundary layer having a one-seventh power profile, but was only about 0.68 to 0.75 of the theoretically obtainable values. Under some operating conditions, flow from the primary jet was exhausted through the auxiliary inlet. This phenomenon could be predicted from the ejector pumping characteristics.

Hearth, Donald P↗