SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
T.M. 311 gave a short outline of modern theoretical aerodynamics as applied to light airplane design. This discussion may have been somewhat obscure to the nontechnical reader. A series of charts or curves should serve to clear up such obscurity as well as to more definitely emphasize those quantities most important for each flight characteristic.
Explore the source record for details and available documents.
A single-engine light airplane was modified by the installation of a wing with reduced area, Fowler flaps, Kruger flaps, and spoilers. Flight test results show that zero-lift drag was reduced 13.8% and a trimmed maximum lift coefficient of 2.73 was achieved. Gust response was significantly reduced and excellent roll control was achieved with spoilers. Several design features employed in the new wings have excellent potential for incorporation in future light airplanes.
Explore the source record for details and available documents.
Results are presented of normal-load-factor calculations made for a lightnormal-category airplane and a light transport-category airplane traversing the trailing vortices generated by each of three heavy transport airplanes. With each light airplane, the normal load factors were determined for several penetration paths lying i n a plane perpendicular to the trailing vortices and for three center-of-gravity locations and velocities. Also determined for the light normal-category airplane were the elevator deflections required to maintain 1 g flight and the vertical displacements of the airplane from the prescribed penetration paths while transversing the vortices.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Harold Bolas, designer, wished the Imp to have two fundamental aims; simplicity and a good view. It is constructed without wire bracing.
The icing characteristics of two typical light-airplane engine induction systems were investigated using the carburetors and manifolds of engines in the horsepower ranges from 65 to 85 and 165 to 185. The smaller system consisted of a float-type carburetor with an unheated manifold and the larger system consisted of a single-barrel pressure-type carburetor with an oil-jacketed manifold. Carburetor-air temperature and humidity limits of visible and serious Icing were determined for various engine power conditions. Several.methods of achieving ice-free induction systems are discussed along with estimates of surface heating requirements of the various induct ion-system components. A study was also made of the icing characteristics of a typical light-airplane air scoop with an exposed filter and a modified system that provided a normal ram inlet with the filter located in a position to Induce inertia separation of the free water from the charge air. The principle of operation of float-type carburetors is proved to make them inherently more susceptible to icing at the throttle plate than pressure-type carburetors.. The results indicated that proper jacketing and heating of all parts exposed to the fuel spray can satisfactorily reduce or eliminate icing in the float-type carburetor and the manifold. Pressure-type carburetors can be protected from serious Icing by proper location of the fuel-discharge nozzle combined with suitable application of heat to critical parts.
Full-scale light-airplane crashes simulating stall-spin accidents were conducted to determine the decelerations to which occupants are exposed and the resulting harness forces encountered in this type of accident. Crashes at impact speeds from 42 to 60 miles per hour were studied. The airplanes used were of the familiar steel-tube, fabric-covered, tandem, two-seat type. In crashes up to an impact speed of 60 miles per hour, crumpling of the forward fuselage structure prevented the maximum deceleration at the rear-seat location from exceeding 26 to 33g. This maximum g value appeared independent of the impact speed. Restraining forces in the seatbelt - shoulder-harness combination reached 5800 pounds. The rear-seat occupant can survive crashes of the type studied at impact speeds up to 60 miles per hour, if body movement is restrained by an adequate seatbelt-shoulder-harness combination so as to prevent injurious contact with obstacles normally present in the cabin. Inwardly collapsing cabin structure, however, is a potential hazard in the higher-speed crashes.
The paper presents an overview of the state-of-the-art of roll control spoilers for light airplanes. Reasons for using spoilers on light airplanes are presented. Several classical objections to the use of spoilers of such airplanes are critically examined. It is shown that mechanically driven spoiler systems can be designed. Flight test results of a new mechanically driven spoiler on the Redhawk airplane are discussed. Tunnel data of spoilers on the new general aviation airfoil GA(W)-1 are presented. Finally, a bibliography on spoiler data is included.
This report begins with a review and analysis of the work being done to develop light airplanes in the U.S. and abroad. A technical discussion of the construction and innovations in light airplanes is then presented.
This paper extends the application of the modified strip theory for wing body combination of a spinning light airplane reported earlier. In addition, to account for the contribution of the tail plane, the shielding effect on vertical tail under steady state spin condition is modeled from basic aerodynamic considerations. The results of this combined analysis, presented for some light airplane configurations, are shown to be in good agreement with spin tunnel rotary balance test data.
The design, efficiency and cost factors are investigated for application of turbofan propulsion engines to single engine, general aviation light airplanes. A companion study of a hypothetical engine family of a thrust range suitable to such aircraft and having a high degree of commonality of design features and parts is presented. Future turbofan powered light airplanes can have a lower fuel consumption, lower weight, reduced airframe maintenance requirements and improved engine overhaul periods as compared to current piston engined powered airplanes. Achievement of compliance with noise and chemical emission regulations is expected without impairing performance, operating cost or safety.
This report presents a review of German light airplane construction. Some of the topics discussed include: engines, fuselages, wings, landing gear, and other mechanical parts.
A discussion of an on-going NASA research project of a gust alleviation system to improve the ride comfort of a light airplane is presented. The discussion includes a description of the proposed system which uses auxiliary aerodynamic surfaces to drive the trailing-edge flaps. The results of analytical work on the effects of the system on stability and effectiveness of the system are presented. Static wind-tunnel tests of the system installed in a 1/6-scale model of a popular light airplane are also described. Problem areas which may need future investigation are discussed.