Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRPLANES - CHARACTERISTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Proton Exchange Membrane Fuel Cells for Electrical Power Generation On-Board Commercial Airplanes

Deployed on a commercial airplane, proton exchange membrane fuel cells may offer emissions reductions, thermal efficiency gains, and enable locating the power near the point of use. This work seeks to understand whether on-board fuel cell systems are technically feasible, and, if so, if they offer a performance advantage for the airplane as a whole. Through hardware analysis and thermodynamic and electrical simulation, we found that while adding a fuel cell system using today’s technology for the PEM fuel cell and hydrogen storage is technically feasible, it will not likely give the airplane a performance benefit. However, when we re-did the analysis using DOE-target technology for the PEM fuel cell and hydrogen storage, we found that the fuel cell system would provide a performance benefit to the airplane (i.e., it can save the airplane some fuel), depending on the way it is configured.

08 HYDROGEN↗

Exposure to tri-o-cresyl phosphate detected in jet airplane passengers

The aircraft cabin and flight deck ventilation are supplied from partially compressed unfiltered bleed air directly from the engine. Worn or defective engine seals can result in the release of engine oil into the cabin air supply. Aircrew and passengers have complained of illness following such 'fume events'. Adverse health effects are hypothesized to result from exposure to tricresyl phosphate mixed esters, a chemical added to jet engine oil and hydraulic fluid for its anti-wear properties. Our goal was to develop a laboratory test for exposure to tricresyl phosphate. The assay was based on the fact that the active-site serine of butyrylcholinesterase reacts with the active metabolite of tri-o-cresyl phosphate, cresyl saligenin phosphate, to make a stable phosphorylated adduct with an added mass of 80 Da. No other organophosphorus agent makes this adduct in vivo on butyrylcholinesterase. Blood samples from jet airplane passengers were obtained 24-48 h after completing a flight. Butyrylcholinesterase was partially purified from 25 ml serum or plasma, digested with pepsin, enriched for phosphorylated peptides by binding to titanium oxide, and analyzed by mass spectrometry. Of 12 jet airplane passengers tested, 6 were positive for exposure to tri-o-cresyl phosphate that is, they had detectable amounts of the phosphorylated peptide FGEpSAGAAS. The level of exposure was very low. No more than 0.05 to 3% of plasma butyrylcholinesterase was modified. None of the subjects had toxic symptoms. Four of the positive subjects were retested 3 to 7 months following their last airplane trip and were found to be negative for phosphorylated butyrylcholinesterase. In conclusion, this is the first report of an assay that detects exposure to tri-o-cresyl phosphate in jet airplane travelers. -- Highlights: Black-Right-Pointing-Pointer Travel on jet airplanes is associated with an illness, aerotoxic syndrome. Black-Right-Pointing-Pointer A possible cause is exposure to tricresyl phosphate in engine lubricating oil. Black-Right-Pointing-Pointer A blood test for exposure to tri-o-cresyl phosphate is reported.

60 APPLIED LIFE SCIENCES↗

Proton exchange membrane fuel cells for electrical power generation on-board commercial airplanes.

Deployed on a commercial airplane, proton exchange membrane fuel cells may offer emissions reductions, thermal efficiency gains, and enable locating the power near the point of use. This work seeks to understand whether on-board fuel cell systems are technically feasible, and, if so, if they offer a performance advantage for the airplane as a whole. Through hardware analysis and thermodynamic and electrical simulation, we found that while adding a fuel cell system using today's technology for the PEM fuel cell and hydrogen storage is technically feasible, it will not likely give the airplane a performance benefit. However, when we re-did the analysis using DOE-target technology for the PEM fuel cell and hydrogen storage, we found that the fuel cell system would provide a performance benefit to the airplane (i.e., it can save the airplane some fuel), depending on the way it is configured.

08 HYDROGEN↗

Low-temperature fuel cell systems for commercial airplane auxiliary power.

This presentation briefly describes the ongoing study of fuel cell systems on-board a commercial airplane. Sandia's current project is focused on Proton Exchange Membrane (PEM) fuel cells applied to specific on-board electrical power needs. They are trying to understand how having a fuel cell on an airplane would affect overall performance. The fuel required to accomplish a mission is used to quantify the performance. Our analysis shows the differences between the base airplane and the airplane with the fuel cell. There are many ways of designing a system, depending on what you do with the waste heat. A system that requires ram air cooling has a large mass penalty due to increased drag. The bottom-line impact can be expressed as additional fuel required to complete the mission. Early results suggest PEM fuel cells can be used on airplanes with manageable performance impact if heat is rejected properly. For PEMs on aircraft, we are continuing to perform: (1) thermodynamic analysis (investigate configurations); (2) integrated electrical design (with dynamic modeling of the micro grid); (3) hardware assessment (performance, weight, and volume); and (4) galley and peaker application.

30 DIRECT ENERGY CONVERSION↗

Behavior of Titanium Alloys in Aerodynamic Heating of Hypersonic Airplanes

The requirements on the use of titanium alloys used as thermal protection in hypersonic airplanes are considered. The ignition of titanium alloys in aerodynamic heating is analyzed. A mathematical model is proposed for the surface oxidation of the alloys in a high-temperature air flux.

42 ENGINEERING↗

A statistical mechanics model for free-for-all airplane passenger boarding

I discuss a model for free-for-all passenger boarding which is employed by some discount air carriers. The model is based on the principles of statistical mechanics where each seat in the aircraft has an associated energy which reflects the preferences of travelers. As each passenger enters the airplane they select their seats using Boltzmann statistics, proceed to that location, load their luggage, sit down, and the partition function seen by remaining passengers is modified to reflect this fact. I discuss the various model parameters and make qualitative comparisons of this passenger boarding model with those that involve assigned seats. The model can be used to predict the probability that certain seats will be occupied at different times during the boarding process. These results might provide a useful description of this boarding method. The model is a relatively unusual application of undergraduate level physics and describes a situation familiar to many students and faculty.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Conversion of Low-Thrust Airplane Gas-Turbine Engines to Power Generators

The local market demand for generators of electric power and heat of output between 7 kW and 2.5 MW is analyzed. State programs relating to the large-scale use of such generators in industry and utility companies are reviewed. Data for generator imports to Russia between 2014 and 2017 suggest that this demand will outstrip supply in the near future. It is expedient to convert low-thrust airplane gas-turbine engines to power generators.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Airplane Combustion of Blended F-T/Conventional Jet Fuel

This unit process provides a summary of relevant input and output flows associated with use of blended jet fuel (50% conventional petroleum, 50% Fischer-Tropsch) to power an aircraft. To access the model referenced in the report, please visit https://www.netl.doe.gov/energy-analysis/details?id=A5594362-B9A9-498A-83C0-3178D0F1C8FF

10 SYNTHETIC FUELS↗

Electric-Discharge Milling of Small Airplane-Engine Components

The production of small complex components by electric-discharge milling is studied by experimental methods. Means of optimizing numerical-control software so as to obtain the required shaping precision are proposed. The proposed systems and equipment permit the development and implementation of designs unattainable by other means.

42 ENGINEERING↗