Search NASA⌕ Search

SEARCH · Search NASA

Results for “ANILINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

The effects of aniline impurities on monopropellant hydrazine thruster performance

Both a 0.45-N and a 0.9-N thruster representative of the designs being flown on 3-axis stabilized spacecraft were used in testing various grades of hydrazine for the phenomenon of monopropellant hydrazine thruster catalyst bed poisoning. Both designs employed Shell 405 ABSG spontaneous catalyst. It is found that pulse shape distortion can be minimized, if not eliminated, by using aniline-free hydrazine. The mechanisms for both steady-state and pulse-mode performance loss are associated with the formation of a catalyst coke similar to the polycyclic aromatic poisons encountered in the petroleum industry. These poisoning mechanisms are reversible, with high-temperature operation being required to drive off the aniline coke deposits. It is recommended that a purified-grade hydrazine be considered for any mission that imposes operational conditions on a thruster which can result in aniline-induced poisoning of the catalyst bed.

Holcomb, L.↗
NASA NTRS1972

A common modality of action of simulated space stresses on the oxidative metabolism of ethylmorphine, aniline and p-nitroanisole by male rat liver.

High gravity, cold and starvation elicited similar responses in male Simonson rats. These responses included a decreased rate in body weight gain, increased metabolism of aniline and p-nitroanisole, and no consistent pattern of change in the metabolism of ethylmorphine. Cold and starvation increased the amount of hepatic cytochrome P-450, while hypobaric-hyperoxia caused no change in any of the parameters measured. When 1% acetone was given to the rats in their drinking water, the effects on drug metabolism were similar to those produced by food restriction in that the metabolism of aniline and p-nitroanisole was increased, and the metabolism of ethylmorphine unchanged. The type I binding spectrum of acetone suggests that it is either a substrate, inhibitor, or both for hepatitic oxidative enzymes.

Furner, R. L.↗
NASA NTRS1977

Site Alteration Effects from Rocket Exhaust Impingement During a Simulated Viking Mars Landing. Part 2: Chemical and Biological Site Alteration

Chemical and biological alteration of a Mars landing site was investigated experimentally and analytically. The experimental testing was conducted using a specially designed multiple nozzle configuration consisting of 18 small bell nozzles. The chemical test results indicate that an engine using standard hydrazine fuel will contaminate the landing site with ammonia (50-500ppm), nitrogen (5-50ppm), aniline (0.01-0.5ppm), hydrogen cyanide (0.01-0.5ppm), and water. A purified fuel, with impurities (mostly aniline) reduced by a factor of 50-100, limits the amount of hydrogen cyanide and aniline to below detectable limits for the Viking science investigations and leaves the amounts of ammonia, nitrogen, and water in the soil unchanged. The large amounts of ammonia trapped in the soil will make interpretation of the organic analysis investigation results more difficult. The biological tests indicate that the combined effects of plume gases, surface heating, surface erosion, and gas composition resulting from the retrorockets will not interfere with the Viking biology investigation.

Husted, R. R.↗
NASA NTRS1981

Synthesis of perfluoroalkylene dianilines

The objective of this contrast was to optimize and scale-up the synthesis of 2,2-bis(4-aminophenyl)-hexafluoropropane and 1,3-bis(4-aminophenyl)hexafluoropropane, as well as to explore avenues to other perfluoroalkyl-bridged dianilines. Routes other than Friedel-Crafts reaction leading to 2,2-bis(4-aminophenyl)hexafluoropropane were investigated. The processes utilizing bisphenol-AF were all unsuccessful; reactions aimed at the production of 4-(hexafluoro-2-halo-isopropyl)aniline from the hydroxyl intermediate failed to yield the desired products. Tailoring the conditions of the Friedel-Crafts reaction of 4-(hexafluoro-2-hydroxyisopropyl)aniline, aniline, and aluminum chloride by using hydrochloride salts and selecting optimum reagent ratios, reaction times, and temperature resulted in approx. 20% yield of pure crystallized 2,2-bis(4-aminophenyl)hexafluoropropane in 0.2 mole reaction batches. Yields up to approx. 40% were realized in small, approx. 0.01 mole, batches. The synthesis of 1,3-bis(4-aminophenyl)hexafluoropropane starting with perfluoroglutarimidine was reinvestigated. The yield of the 4-step reaction sequence giving 1,3-bis(4-acetamidophenyl)hexafluoropropane was raised to 44%. The yield of the subsequent hydrolysis process was improved by a factor of approx. 2. Approaches to prepare other perfluoroalkyl-bridged dianilines were unsuccessful. Reactions reported to proceed readily with trifluoromethyl substituents failed when longer chain perfluoroalkyl groups were employed.

Paciorek, K. L.↗
NASA NTRS1945

Net Heat of Combustion of AN-F-28 Aviation Gasolines

Experimental data on the heats of combustion and hydrogen contents of a number of aviation gasolines have been used in deriving a formula for computing net heat of combustion from (measured) gross heat of combustion. This formula appears to be sufficiently reliable for the purpose and has the advantage of making hydrogen determinations unnecessary. The data on heats of combustion are presented in tabular form, and in graphs showing the relation between net heat of combustion and (1) hydrogen content, (2) aniline point, (3) APO gravity, and (4) the product of aniline point and APO gravity. Data are given on the change in aniline point with time, and also the change resulting from the addition of xylidine.

FUELS - COMBUSTION TEMPERATURES↗
DOE OSTI2026

Coordination-Induced Weakening of N–H Bonds Driven by Bimetallic Cooperativity in Zr/Co Compounds

The bond dissociation free energy (BDFE) of the element-hydrogen bonds of protic substrates have been found to decrease upon metal coordination. Herein, an early/late heterobimetallic complex is used to examine the impact on the BDFE N−H when the substrate binding site and the redox-active site are two different metals that are spatially separated. A tris- (phosphinoamide) framework is used to link a d 0 ZrIV center with an accessible substrate binding site to a coordinatively saturated redox-active Co center, which serves as an appended electron reservoir. A series of aniline, amido, and imido Zr/Co model compounds were synthesized starting from the Zr IV /Co −I aniline adduct PhH 2 N−Zr(MesNP i Pr 2 ) 3 CoCN t Bu (2). 2,4,6-tristert- butylphenoxyl radical ( t Bu 3 ArO • ) was used to abstract one or two H atoms and produce the amido and imido complexes PhHNZr( MesNP i Pr 2 ) 3 CoCN t Bu (3) and PhN≡Zr(MesNP i Pr 2 ) 3 CoCNtBu (4), respectively. Using open-circuit potential measurements, the BDFE N−H within 2 and 3 were determined to be 37 kcal/mol (2) and 55 kcal/mol (3). Cyclic voltammetry measurements were conducted to determine the Co I/0 and Co 0/−I redox potentials. The pK a s were then estimated using the Bordwell equation to provide further insight into the thermochemical aspects of the observed proton coupled electron transfer (PCET) reactions.

Bond dissociation free energy↗
NASA NTRS1988

The synthesis of conducting polymers for corrosion prevention

The formation of an electrically conducting form of polyaniline by the oxidative polymerization of aniline was studied. Optimum yield and conductivities were obtained by treating aniline in 2 molar hydrochloric acid at 0 to 5 C with ammonium persulfate in 1.15 mole ratio. The yield was 37.6 percent of theory and the conductivity of the product was 10.5 S/cm. This material was formulated into epoxy and acrylic coatings which were also electrically conductive.

Mattson, Guy C.↗
NASA NTRS1989

Substituted 1,1,1-triaryl-2,2,2-trifluoroethanes and processes for their synthesis

Synthetic procedures are disclosed for tetraalkyls, tetraacids, and dianhydrides substituted 1,1,1-triaryl 2,2,2-trifluoroethanes which comprises: (1) 1,1-bis (dialkylaryl) 1-aryl 2,2,2-trifluoroethane, (2) 1,1-bis (dicarboxyaryl) 1-aryl 2,2,2-trifluoroethane, or (3) cyclic dianhydride or diamine of 1,1-bis (dialkylaryl) 1-aryl 2,2,2-trifluoroethanes. The synthesis of (1) is accomplished by the condensation reaction of an aryltrifluoromethyl ketone with a dialkylaryl compound. The synthesis of (2) is accomplished by the oxidation of (1). The synthesis dianhydride of (3) is accomplished by the conversion of (2) to its corresponding cyclic dianhydride. The synthesis of the diamine is accomplished by the similar reaction of an aryltrifluoromethyl ketone with aniline or aklyl substituted or disubstituted anilines. Also, other derivatives of the above are formed by nucleophilic displacement reactions.

Alston, William B.↗
NASA NTRS1992

Substituted 1,1,1-triaryl 2,2,2-trifluoroethanes and processes for their synthesis

Synthetic procedures to tetraalkyls, tetraacids, and dianhydrides substituted 1,1,1-triaryl 2,2,2-trifluoroethanes which comprises: (1) 1,1-bis(dialkylaryl) 1-aryl-2,2,2-trifluoroethane, (2) 1,1-bis(dicarboxyaryl) 1-aryl-2,2,2-trifluoroethane, or (3) cyclic dianhydride or diamine of 1,1-bis(dialkylaryl) 1-aryl-2,2,2-trifluoroethanes. The synthesis of (1) is accomplished by the condensation reaction of an aryltrifluoromethyl ketone with a dialkylaryl compound. The synthesis of (2) is accomplished by oxidation of (1). The synthesis dianhydride of (3) is accomplished by the conversion of (2) to its corresponding cyclic dianhydride. The synthesis of the diamine is accomplished by the similar reaction of an aryltrifluoromethyl ketone with aniline or alkyl substituted or disubstituted anilines. Also, other derivatives of the above are formed by nucleophilic displacement reactions.

Alston, William B.↗
NASA NTRS1993

Di(hydroxyphenyl)- 1,2,4-triazole monomers

The di(hydroxyphenyl)- 1,2,4-triazole monomers were first synthesized by reacting bis (4-hydroxyphenyl) hydrazide with aniline hydrochloride at 250 C in the melt and also by reacting 1,3 or 1,4-bis- (4-hydroxyphenyl)- phenylene- dihydrazide with 2 moles of aniline hydrochloride in the melt. Purification of the di(hydroxyphenyl)- 1,2,4-triazole monomers was accomplished by recrystallization. Poly (1,2,4-triazoles) (PT) were prepared by the aromatic nucleophilic displacement reaction of di(hydroxyphenyl)- 1,2,4-triazole monomers with activated aromatic dihalides or activated aromatic dinitro compounds. The reactions were carried out in polar aprotic solvents such as sulfolane or diphenylsulfone using alkali metal bases such as potassium carbonate at elevated temperatures under nitrogen. This synthetic route has provided high molecular weight PT of new chemical structure, is economically and synthetically more favorable than other routes, and allows for facile chemical structure variation due to the availability of a large variety of activated aromatic dihalides.

Connell, John W.↗
NASA NTRS1994

Substituted 1,1,1-triaryl-2,2,2-trifluoroethanes and processes for their synthesis

Synthetic procedures are given for tetraalkyl, tetraacid and dianhydrides substituted 1,1,1-triaryl-2,2,2-trifluoroethanes which comprises: (1) 1,1-bis (dialkylaryl) 1-aryl-2,2,2 trifluoroethane; (2) 1,1-bis (dicarboxyaryl) 1-aryl-2,2,2 trifluoroethane; or (3) cyclic dianhydride or diamine of 1,1-bis (dialkylaryl) 1-aryl-2,2,2 trifluoroethanes. The synthesis of (1) is accomplished by the condensation reaction of an aryltrifluoromethyl ketone with a dialkylaryl compound. The synthesis of (2) is accomplished by oxidation of (1). The synthesis dianhydride of (3) is accomplished by the conversion of (2) to its corresponding cyclic dianhydride. The synthesis of the diamine is accomplished by the similar reaction of an aryltrifluoromethyl ketone with aniline or alkyl substituted or disubstituted anilines. Also, other derivatives of the above are formed by nucleophilic displacement reactions.

Alston, William B.↗
NASA NTRS1997

Three-Dimensional Polybenzobisoxazoles and Polybenzobisthiazoles

Due to the poor compressive strength properties of high performance liquid crystalline polymers such as polybenzobisoxazoles (PBOs) and polybenzobisthiazoles (PBTs), we have prepared homopolymers and copolymers with PBO and PBT pendant groups on a central star-like unit, 2.7-diamino-9,9'-bis(4-aminophenyl)fluorene, in order to improve upon their compressive strength properties. The fluorene moiety was prepared by the reaction of 2,7-dinitro-9-fluorene with aniline and aniline hydrochloride, followed by reduction with palladium on carbon. The central star-like unit was characterized by FTIR, FTNMR, and elemental analysis. The PBO and PBT pendant groups were synthesized by the polycondensation of 4,6-diaminoresorcinol dihydrochloride with terephthaloyl chloride and 2,5-diamino-1,4-benzendithiol dihydrochloride with terephthaloyl chloride in poly(phosphoric acid), respectively. The resulting linear polymers containing the dicarboxylic end groups were attached to the central star-like unit by refluxing with 2,7-diamino-9,9'-bis(4-aminophenyl) fluorene to give the star-like polymers. The star-like PBO and PBT were soluble in methanesulfonic acid. Further characterization of the polymers is ongoing.

Bray, M.↗