Search NASA⌕ Search

SEARCH · Search NASA

Results for “AUTOMOBILE ENGINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Unsupervised Image-Based Classification of Corrosion Severity in Automobile Engine Connecting Rods

Corrosion in engine connecting rods is a critical issue in the automotive industry, potentially leading to catastrophic engine failure, monetary losses, and safety hazards. The labor shortage in the industry further emphasizes the need for fast, accurate, and automated corrosion detection methods to ensure appropriate surface treatments can be applied to restore component integrity. We present an unsupervised image-based framework for classifying corrosion severity in automobile engine connecting rods using short-wave infrared (SWIR) and telecentric grayscale imaging. We employ the structural similarity index measure (SSIM) as a dissimilarity metric and the k-medians clustering algorithm for classification. Our algorithm achieves an overall accuracy of 80.64% for SWIR images, with 100% accuracy in classifying highly corroded samples. For grayscale images, the method attains an overall accuracy of 77.42%, with 90.91% accuracy for highly corroded samples. The method’s ability to work with different imaging modalities and its high accuracy in identifying severe corrosion cases make it a promising tool for automated corrosion assessment in the automotive industry, potentially improving efficiency and safety in engine component maintenance.

42 ENGINEERING↗
NASA NTRS1982

Experimental performance of the regenerator for the Chrysler upgraded automotive gas turbine engine

Automobile gas turbine engine regenerator performance was studied in a regenerator test facility that provided a satisfactory simulation of the actual engine operating environment but with independent control of airflow and gas flow. Velocity and temperature distributions were measured immediately downstream of both the core high-pressure-side outlet and the core low-pressure-side outlet. For the original engine housing, the regenerator temperature effectiveness was 1 to 2 percent higher than the design value, and the heat transfer effectiveness was 2 to 4 percent lower than the design value over the range of test conditions simulating 50 to 100 percent of gas generator speed. Recalculating the design values to account for seal leakage decreased the design heat transfer effectiveness to values consistent with those measured herein. A baffle installed in the engine housing high-pressure-side inlet provided more uniform velocities out of the regenerator but did not improve the effectiveness. A housing designed to provide more uniform axial flow to the regenerator was also tested. Although temperature uniformity was improved, the effectiveness values were not improved. Neither did 50-percent flow blockage (90 degree segment) applied to the high-pressure-side inlet change the effectiveness significantly.

Winter, J. M.↗
NASA NTRS1979

Stirling engines for automobiles

The results of recent and ongoing automobile Stirling engine development efforts are reviewed and technology status and requirements are identified. Key technology needs include those for low cost, high temperature (1300 - 1500 F) metal alloys for heater heads, and reliable long-life, low-leakage shaft seals. Various fuel economy projections for Stirling powered automobiles are reviewed and assessed.

Beremand, D. G.↗
NASA NTRS1983

New perspectives for advanced automobile diesel engines

Computer simulation results are presented for advanced automobile diesel engine performance. Four critical factors for performance enhancement were identified: (1) part load preheating and exhaust gas energy recovery, (2) fast heat release combustion process, (3) reduction in friction, and (4) air handling system efficiency. Four different technology levels were considered in the analysis. Simulation results are compared in terms of brake specific fuel consumption and vehicle fuel economy in km/liter (miles per gallon). Major critical performance sensitivity areas are: (1) combustion process, (2) expander and compressor efficiency, and (3) part load preheating and compound system. When compared to the state of the art direct injection, cooled, automobile diesel engine, the advanced adiabatic compound engine concept showed the unique potential of doubling the fuel economy. Other important performance criteria such as acceleration, emissions, reliability, durability and multifuel capability are comparable to or better than current passenger car diesel engines.

Tozzi, L.↗
NASA NTRS1993

Chemical Vapor Deposition Of Silicon Carbide

Large single-crystal SiC boules from which wafers of large area cut now being produced commerically. Availability of wafers opens door for development of SiC semiconductor devices. Recently developed chemical vapor deposition (CVD) process produces thin single-crystal SiC films on SiC wafers. Essential step in sequence of steps used to fabricate semiconductor devices. Further development required for specific devices. Some potential high-temperature applications include sensors and control electronics for advanced turbine engines and automobile engines, power electronics for electromechanical actuators for advanced aircraft and for space power systems, and equipment used in drilling of deep wells. High-frequency applications include communication systems, high-speed computers, and microwave power transistors. High-radiation applications include sensors and controls for nuclear reactors.

Powell, J. Anthony↗
NASA NTRS1979

Thermal energy storage for the Stirling engine powered automobile

A thermal energy storage (TES) system developed for use with the Stirling engine as an automotive power system has gravimetric and volumetric storage densities which are competitive with electric battery storage systems, meets all operational requirements for a practical vehicle, and can be packaged in compact sized automobiles with minimum impact on passenger and freight volume. The TES/Stirling system is the only storage approach for direct use of combustion heat from fuel sources not suitable for direct transport and use on the vehicle. The particular concept described is also useful for a dual mode TES/liquid fuel system in which the TES (recharged from an external energy source) is used for short duration trips (approximately 10 miles or less) and liquid fuel carried on board the vehicle used for long duration trips. The dual mode approach offers the potential of 50 percent savings in the consumption of premium liquid fuels for automotive propulsion in the United States.

Morgan, D. T.↗
NASA NTRS1981

Applicability of advanced automotive heat engines to solar thermal power

The requirements of a solar thermal power system are reviewed and compared with the predicted characteristics of automobile engines under development. A good match is found in terms of power level and efficiency when the automobile engines, designed for maximum powers of 65-100 kW (87 to 133 hp) are operated to the nominal 20-40 kW electric output requirement of the solar thermal application. At these reduced power levels it appears that the automotive gas turbine and Stirling engines have the potential to deliver the 40+ percent efficiency goal of the solar thermal program.

Beremand, D. G.↗
NASA NTRS1992

A Segmented Ion-Propulsion Engine

New design approach for high-power (100-kW class or greater) ion engines conceptually divides single engine into combination of smaller discharge chambers integrated to operate as single large engine. Analogous to multicylinder automobile engine, benefits include reduction in required accelerator system span-to-gap ratio for large-area engines, reduction in required hollow-cathode emission current, mitigation of plasma-uniformity problem, increased tolerance to accelerator system faults, and reduction in vacuum-system pumping speed.

Brophy, John R.↗
NASA NTRS1926

On the knocking of gasoline engines

It is of the greatest importance, not only for automobile engines, but also for every other kind of internal combustion engine, since it limits the degree of compression and the thermal efficiency and its investigation indicates ways for saving fuel.

DETONATION↗
NASA NTRS1981

Conventional engine technology. Volume 3: Comparisons and future potential

The status of five conventional automobile engine technologies was assessed and the future potential for increasing fuel economy and reducing exhaust emission was discussed, using the 1980 EPA California emisions standards as a comparative basis. By 1986, the fuel economy of a uniform charge Otto engine with a three-way catalyst is expected to increase 10%, while vehicles with lean burn (fast burn) engines should show a 20% fuel economy increase. Although vehicles with stratified-charge engines and rotary engines are expected to improve, their fuel economy will remain inferior to the other engine types. When adequate NO emissions control methods are implemented to meet the EPA requirements, vehicles with prechamber diesel engines are expected to yield a fuel economy advantage of about 15%. While successful introduction of direct injection diesel engine technology will provide a fuel savings of 30 to 35%, the planned regulation of exhaust particulates could seriously hinder this technology, because it is expected that only the smallest diesel engine vehicles could meet the proposed particulate requirements.

Dowdy, M. W.↗
NASA NTRS1981

The storage of hydrogen in the form of metal hydrides: An application to thermal engines

The possibility of using LaNi56, FeTiH2, or MgH2 as metal hydride storage sytems for hydrogen fueled automobile engines is discussed. Magnesium copper and magnesium nickel hydrides studies indicate that they provide more stable storage systems than pure magnesium hydrides. Several test engines employing hydrogen fuel have been developed: a single cylinder motor originally designed for use with air gasoline mixture; a four-cylinder engine modified to run on an air hydrogen mixture; and a gas turbine.

Gales, C.↗
NASA NTRS1996

Flying Cars

Flying cars have nearly mythical appeal to nonpilots, a group that includes almost the whole human race. The appeal resides in the perceived utility of flying cars, vehicles that offer portal-to-portal transportation, yet break the bonds of road and traffic and travel freely through the sky at the drivers will. Part of the appeal is an assumption that flying cars can be as easy to fly as to drive. Flying cars have been part of the dream of aviation since the dawn of powered flight. Glenn Curtiss built, displayed, and maybe even flew a flying car in 1917, the Curtiss Autoplane. Many roadable airplanes were built in the 1930's, like the Waterman Arrowbile and the Fulton Airphibian. Two flying cars came close to production in the early 1950's. Ted Hall built a series of flying cars culminating in the Convaircar, sponsored by Consolidated Vultee, General Motors, and Hertz. Molt Taylor built and certified his Aerocar, and Ford came close to producing them. Three Aerocars are still flyable, two in museums in Seattle and Oshkosh, and the third owned and flown by Ed Sweeny. Flying cars do have problems, which so far have prevented commercial success. An obvious problem is complexity of the vehicle, the infrastructure, or both. Another is the difficulty of matching low power for normal driving with high power in flight. An automobile uses only about 20 hp at traffic speeds, while a personal airplane needs about 160 hp at speeds typical of flight. Many automobile engines can deliver 160 hp, but not for very long. A more subtle issue involves the drag of automobiles and airplanes. A good personal airplane can fly 30 miles per gallon of fuel at 200 mph. A good sports car would need 660 hp at the same speed and would travel only 3 miles per gallon. The difference is drag area, about 4.5 sq ft for the automobile and 1.4 sq ft for the airplane. A flying car better have the drag area of the airplane, not the car!

Crow, Steven↗
NASA NTRS1926

The Fundamental Principles of High-speed Semi-diesel Engines. Part I: a General Discussion of the Subject of Fuel Injection in Diesel Engines and Detailed Descriptions of Many Types of Injection Nozzles

Three questions relating to the technical progress in the utilization of heavy oils are discussed. The first question considers solid injection in high-speed automobile engines, the second concerns the development of the hot-bulb engine, and the third question relates to the need for a more thorough investigation of the processes on which the formatation of combustible, rapidly-burning mixtures depend.

NOZZLES, FUEL - PEUGEOT-TARTRAIS↗
NASA NTRS1994

Melt-Infiltration Process For SiC Ceramics And Composites

Reactive melt infiltration produces silicon carbide-based ceramics and composites faster and more economically than do such processes as chemical vapor infiltration (CVI), reaction sintering, pressureless sintering, hot pressing, and hot isostatic pressing. Process yields dense, strong materials at relatively low cost. Silicon carbide ceramics and composites made by reactive melt infiltration used in combustor liners of jet engines and in nose cones and leading edges of high-speed aircraft and returning spacecraft. In energy industry, materials used in radiant-heater tubes, heat exchangers, heat recuperators, and turbine parts. Materials also well suited to demands of advanced automobile engines.

Behrendt, Donald R.↗
NASA NTRS1982

Modular Engine Instrumentation System

System that provides information and measurements never obtained before in real time has been developed. System shows not only real-time measurements but also results of computations of key combustion parameters in meaningful and easily understood display. Standard commercially-available shaft encoder plus data from pressure transducer act as principal drivers to device. Eventually, modular system could be developed into onboard controller for automobile engines.

Rice, W. J.↗
DOE OSTI2021

Shear thinning rheology in a concentrated suspension of fibers: the role of attractive interactions

Fiber-reinforced composites are ubiquitously encountered in the engineering, automobile, and aerospace industries. Fabrication of these composites requires the mixing of fibers dispersed in a liquid, and the final structure is affected by fiber properties, interactions, and flow fields. A good understanding of the rheology of fiber suspensions can aid in the design and optimization of the fabrication processes. To this end, we simulate the simple shear flow of fiber suspensions by accounting for short range lubrication, van der Waals attractive, electrostatic repulsion interactions, as well as friction between fibers. Direct numerical simulations are performed using the Immersed Boundary Method where the fibers are modeled as flexible slender bodies governed by the Euler-Bernoulli beam theory and the fluid flow is resolved using the Navier-Stokes equations. The simulation results for the suspension viscosity and yield stress are consistent with the experimental data from the literature for polyamide fiber suspensions. The shear-thinning behavior becomes stronger as we increase the magnitude of attractive interactions. Furthermore, we perform a parametric study varying fiber flexibility, volume fraction, aspect ratio, inertia and examine suspension viscosity and yield stress.

Khan, Monsurul↗