SEARCH · Search NASA

Results for “Active Flow Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS2007

High-Lift System for a Supercritical Airfoil: Simplified by Active Flow Control

Active flow control wind tunnel experiments were conducted in the NASA Langley Low-Turbulence Pressure Tunnel using a two-dimensional supercritical high-lift airfoil with a 15% chord hinged leading-edge flap and a 25% chord hinged trailing-edge flap. This paper focuses on the application of zero-net-mass-flux periodic excitation near the airfoil trailing edge flap shoulder at a Mach number of 0.1 and chord Reynolds numbers of 1.2 x 10(exp 6) to 9 x 10(exp 6) with leading- and trailing-edge flap deflections of 25 deg. and 30 deg., respectively. The purpose of the investigation was to increase the zero-net-mass-flux options for controlling trailing edge flap separation by using a larger model than used on the low Reynolds number version of this model and to investigate the effect of flow control at higher Reynolds numbers. Static and dynamic surface pressures and wake pressures were acquired to determine the effects of flow control on airfoil performance. Active flow control was applied both upstream of the trailing edge flap and immediately downstream of the trailing edge flap shoulder and the effects of Reynolds number, excitation frequency and amplitude are presented. The excitations around the trailing edge flap are then combined to control trailing edge flap separation. The combination of two closely spaced actuators around the trailing-edge flap knee was shown to increase the lift produced by an individual actuator. The phase sensitivity between two closely spaced actuators seen at low Reynolds number is confirmed at higher Reynolds numbers. The momentum input required to completely control flow separation on the configuration was larger than that available from the actuators used.

Melton, LaTunia Pack↗

NASA NTRS2022

Low-Speed Performance Enhancement Using Localized Active Flow Control: Localized Active Flow Control Simulations on a Reference Aircraft (2/4)

A study of the potential implementations of localized active flow control (AFC) technology onto future airplanes is presented. This collaborative investigation addresses key objectives of the NASA Advanced Air Transport Technology (AATT) Project, in terms of reduction in fuel consumption and lower emission. It specifically targets the goals set forth in a roadmap developed by the NASA/Boeing team. The roadmap is a result of a series of meetings held between the two parties over the years and it represents a shared vision for practical implementations, leading up to flight demonstrations of localized flow control. If successful, localized flow control may lead to important ramifications for next generation airplanes from both the economic and environmental perspectives. Under this contract localized AFC has been used to improve aerodynamic performance during high-lift operations using Computational Fluid Dynamics (CFD). Specifically, AFC has been applied at the aileron and at various location in the wing leading edge (LE) regions. The applications target reduced drag and enhanced lift over the range of practical angles of attack, including stall. These benefits translate to airplane performance improvements, such as longer range or larger payload. The CFD results are used to quantify potential aerodynamic benefits, as well as the input required for actuation. This helps identify the most promising candidates, which potentially provide material net airplane level enhancements using onboard fluidic sources. The airplane configuration selected for the CFD study is a representative of a future short/medium-range twin-engine airplane dubbed the Reference Aircraft. A slew of AFC applications has been explored and their aerodynamic performance enhancements were benchmarked against the baseline Reference Aircraft. Promising AFC candidates have been deemed practical and potentially suitable for both the aileron and the wing LE implementations. The findings on the Reference Aircraft are used to guide the development of the AFC-enhanced aileron for the CRM-HL. The wind-tunnel model of the CRM-HL will be used by NASA to validate the AFC concepts, complementing the CFD-based analysis and the integration study (final report document #3).

CFD↗

NASA NTRS2004

Active Flow Control Activities at NASA Langley

NASA Langley continues to aggressively investigate the potential advantages of active flow control over more traditional aerodynamic techniques. This paper provides an update to a previous paper and describes both the progress in the various research areas and the significant changes in the NASA research programs. The goals of the topics presented are focused on advancing the state of knowledge and understanding of controllable fundamental mechanisms in fluids as well as to address engineering challenges. An organizational view of current research activities at NASA Langley in active flow control as supported by several projects is presented. On-center research as well as NASA Langley funded contracts and grants are discussed at a relatively high level. The products of this research are to be demonstrated either in bench-top experiments, wind-tunnel investigations, or in flight as part of the fundamental NASA R&D program and then transferred to more applied research programs within NASA, DOD, and U.S. industry.

Anders, Scott G.↗

NASA NTRS2016

Acoustic Study of a Sweeping Jet Actuator for Active Flow Control Applications

Active flow control for aircraft has been demonstrated to improve aerodynamic performance but generally introduces additional noise sources. This study presents measurements of the acoustic fields of sweeping jet actuators at full- and half-scale compared to the configuration recently demonstrated in ground- and flight-tests of a full-scale rudder. The effects of scale, flow rate, forward speed, and actuator synchronization state on tone and broadband noise directional power spectral density (PSD) levels are presented. The sweeping jet actuator PSD levels in the audio range increases as the second power of actuator flow rate. A fourth power variation of PSD level with flow rate is observed for a comparable non-sweeping actuator. These measurements will be used to develop noise source models for new aircraft configurations utilizing active flow control.

Active Flow Control Noise↗

NASA NTRS2022

Low-Speed Performance Enhancement using Localized Active Flow Control: Integration Study of Localized Active Flow Control on a Performance Reference Aircraft (3/4)

A study of conceptual integration and performance aspects of localized active flow control (AFC) technology onto wings of short-to-medium-range project passenger airplanes is summarized. Using predicted aerodynamic performance improvement opportunities on the CFD Reference Aircraft, estimated benefit opportunities for conceptual implementation of studied wing localized active flow control (AFC) technology for low-speed (take-off and landing) application on a Performance Reference Aircraft configuration are presented. Using conceptual AFC systems and structural integration weight penalties for studied concepts, potential relevant net performance benefits can be obtained with reliable AFC in takeoff and landing. The conceptual integration study identifies potential promising localized wing AFC application opportunities for high-lift conditions using energy sources for modern aircraft. Material benefits are estimated for take-off and landing configurations for selected localized AFC applications. Next steps to refine and expand results of investigated topics, as well as possible other local AFC wing applications, are suggested.

AFC↗

NASA NTRS2007

Influence of Finite Span and Sweep on Active Flow Control Efficacy

Active flow control efficacy was investigated by means of leading-edge and flap-shoulder zero mass-flux blowing slots on a semispan wing model that was tested in unswept (standard) and swept configurations. On the standard configuration, stall commenced inboard, but with sweep the wing stalled initially near the tip. On both configurations, leading-edge perturbations increased C(sub L,max) and post stall lift, both with and without deflected flaps. Without sweep, the effect of control was approximately uniform across the wing span but remained effective to high angles of attack near the tip; when sweep was introduced a significant effect was noted inboard, but this effect degraded along the span and produced virtually no meaningful lift enhancement near the tip, irrespective of the tip configuration. In the former case, control strengthened the wingtip vortex; in the latter case, a simple semi-empirical model, based on the trajectory or streamline of the evolving perturbation, served to explain the observations. Control on finite-span flaps did not differ significantly from their two-dimensional counterpart, while control over a tip flap produced significant variations to all three moments in the presence of large deflection and these variations were linear with input slot momentum. Control from the flap produced expected lift enhancement and CL,max improvements in the absence of sweep, but these improvements degraded with the introduction of sweep.

Greenblatt, David↗

NASA NTRS2008

Influence of Finite Span and Sweep on Active Flow Control Efficacy

Active flow control efficacy was investigated by means of leading-edge and flap-shoulder zero mass-flux blowing slots on a semispan wing model that was tested in unswept (standard) and swept configurations. On the standard configuration, stall commenced inboard, but with sweep the wing stalled initially near the tip. On both configurations, leading-edge perturbations increased CL,max and post stall lift, both with and without deflected flaps. Without sweep, the effect of control was approximately uniform across the wing span but remained effective to high angles of attack near the tip; when sweep was introduced a significant effect was noted inboard, but this effect degraded along the span and produced virtually no meaningful lift enhancement near the tip, irrespective of the tip configuration. In the former case, control strengthened the wingtip vortex; in the latter case, a simple semi-empirical model, based on the trajectory or "streamline" of the evolving perturbation, served to explain the observations. In the absence of sweep, control on finite-span flaps did not differ significantly from their nominally twodimensional counterpart. Control from the flap produced expected lift enhancement and CL,max improvements in the absence of sweep, but these improvements degraded with the introduction of sweep.

Greenblatt, David↗

NASA NTRS2022

Low-Speed Performance Enhancement using Localized Active Flow Control: Simulations, Scaling and Design of Localized Active Flow Control on the Common Research Model (4/4)

This report is dedicated to the application of localized AFC on the NASA CRM-HL wind tunnel model, with focus on the aileron application discussed in the CFD study (final report document #2). The experience developed for the Reference Aircraft guided the implementation on the CRM model. CFD evaluations are performed on a representative high-lift configuration, for a set of aileron deflections, and at relevant flow conditions. Alternative flow control actuator layouts are proposed and design consideration for practical integration into the existing CRM-HL model are set forth. The CFD simulations indicate that the aerodynamic performance improvements due to AFC obtained for the CRM-HL are consistent with those achieved for the Reference Aircraft. The observed changes in L/D are smaller than for the Reference Aircraft because the CRM has a higher leading edge sweep angle and a different relative aileron size. Conceptual design studies confirmed that the integration of an AFC equipped aileron into the existing wind tunnel model is feasible.

AFC↗

NASA NTRS1999

Transitioning Active Flow Control to Applications

Active Flow Control Programs at NASA, the U.S. Air Force, and DARPA have been initiated with the goals of obtaining revolutionary advances in aerodynamic performance and maneuvering compared to conventional approaches. These programs envision the use of actuators, sensors, and controllers on applications such as aircraft wings/tails, engine nacelles, internal ducts, nozzles, projectiles, weapons bays, and hydrodynamic vehicles. Anticipated benefits of flow control include reduced weight, part count, and operating cost and reduced fuel burn (and emissions), noise and enhanced safety if the sensors serve a dual role of flow control and health monitoring. To get from the bench-top or laboratory test to adaptive distributed control systems on realistic applications, reliable validated design tools are needed in addition to sub- and large-scale wind-tunnel and flight experiments. This paper will focus on the development of tools for active flow control applications.

Joslin, Ronald D.↗

NASA NTRS2013

Hot-Film and Hot-Wire Anemometry for a Boundary Layer Active Flow Control Test

Unsteady active flow control (AFC) has been used experimentally for many years to minimize bluff-body drag. This technology could significantly improve performance of rotorcraft by cleaning up flow separation. It is important, then, that new actuator technologies be studied for application to future vehicles. A boundary layer wind tunnel was constructed with a 1ft-x-3ft test section and unsteady measurement instrumentation to study how AFC manipulates the boundary layer to overcome adverse pressure gradients and flow separation. This unsteady flow control research requires unsteady measurement methods. In order to measure the boundary layer characteristics, both hot-wire and hot-film Constant Temperature Anemometry is used. A hot-wire probe is mounted in the flow to measure velocity while a hot-film array lays on the test surface to measure skin friction. Hot-film sensors are connected to an anemometer, a Wheatstone bridge circuit with an output that corresponds to the dynamic flow response. From this output, the time varying flow field, turbulence, and flow reversal can be characterized. Tuning the anemometers requires a fan test on the hot-film sensors to adjust each output. This is a delicate process as several variables drastically affect the data, including control resistance, signal input, trim, and gain settings.

Control Test↗

NASA NTRS2003

Compressor Performance Enhanced by Active Flow Control Over Stator Vanes

The application of active flow control technology to enhance turbomachinery system performance is being investigated at the NASA Glenn Research Center through experimental studies. Active flow control involves the use of sensors and actuators embedded within engine components to dynamically alter the internal flow path during off nominal operation in order to optimize engine performance and maintain stable operation. Modern compressors are already highly optimized components that must be designed to accommodate a broad range of operating conditions in a safe and efficient manner. Since overall engine performance is driven by compressor performance, advances in compressor technology that reduce weight and parts count, reduce fuel consumption, and lower maintenance costs will have a significant impact on the cost of aircraft ownership. Active flow control holds the promise of delivering such technology advances.

Culley, Dennis E.↗

NASA NTRS2010

Active Flow Control Stator With Coanda Surface

Active Flow Control increases the permissible aerodynamic loading. Curved surface near the trailing edge ("Coanda surface"): a) increases turning -> higher pressure ratio. b) controls boundary layer separation -> increased surge margin. Objective: Reduce the number of vanes or compressor stages. Constraints: 1. In a real compressor, the vane must still function entirely without blowing. 2. Maintain the flow exit angle of the reference stator despite the resulting increase in stator loading.

Guendogdu↗

NASA NTRS2019

Active Flow Control on Vertical Tail Models

Active flow control (AFC) subscale experiments were conducted at the Lucas Wind Tunnel of the California Institute of Technology. Tests were performed on a generic vertical tail model at low speeds. Fluidic oscillators were used at the trailing edge of the main element (vertical stabilizer) to redirect the flow over the rudder and delay or prevent flow separation. Side force increases in excess of 50% were achieved with a 2% momentum coefficient (C(sub μ)) input. The results indicated that a collective C(sub μ) of about 1% could increase the side force by 30–50%. This result is achieved by reducing the spanwise flow on the swept back wings that contributes to early flow separation near their tips. These experiments provided the technical backdrop to test the full-scale Boeing 757 vertical tail model equipped with a fluidic oscillator system at the National Full-scale Aerodynamics Complex 40-by 80-foot Wind Tunnel, NASA Ames Research Center. The C(sub μ) is shown to be an important parameter for scaling a fluidic oscillator AFC system from subscale to full-scale wind tunnel tests. The results of these tests provided the required rationale to use a fluidic oscillator AFC configuration for a follow-on flight test on the Boeing 757 ecoDemonstrator.

Andino, Marlyn Y.↗

NASA NTRS2001

CFD Modeling for Active Flow Control

This presentation describes current work under UEET Active Flow Control CFD Research Tool Development. The goal of this work is to develop computational tools for inlet active flow control design. This year s objectives were to perform CFD simulations of fully gridded vane vortex generators, micro-vortex genera- tors, and synthetic jets, and to compare flowfield results with wind tunnel tests of simple geometries with flow control devices. Comparisons are shown for a single micro-vortex generator on a flat plate, and for flow over an expansion ramp with sidewall effects. Vortex core location, pressure gradient and oil flow patterns are compared between experiment and computation. This work lays the groundwork for evaluating simplified modeling of arrays of devices, and provides the opportunity to test simple flow control device/sensor/ control loop interaction.

Buning, Pieter G.↗

NASA NTRS2004

Active Flow Control on a Boundary-Layer-Ingesting Inlet

Boundary layer ingestion (BLI) is explored as means to improve overall system performance for Blended Wing Body configuration. The benefits of BLI for vehicle system performance benefit are assessed with a process derived from first principles suitable for highly-integrated propulsion systems. This performance evaluation process provides framework within which to assess the benefits of an integrated BLI inlet and lays the groundwork for higher-fidelity systems studies. The results of the system study show that BLI provides a significant improvement in vehicle performance if the inlet distortion can be controlled, thus encouraging the pursuit of active flow control (AFC) as a BLI enabling technology. The effectiveness of active flow control in reducing engine inlet distortion was assessed using a 6% scale model of a 30% BLI offset, diffusing inlet. The experiment was conducted in the NASA Langley Basic Aerodynamics Research Tunnel with a model inlet designed specifically for this type of testing. High mass flow pulsing actuators provided the active flow control. Measurements were made of the onset boundary layer, the duct surface static pressures, and the mass flow through the duct and the actuators. The distortion was determined by 120 total pressure measurements located at the aerodynamic interface plane. The test matrix was limited to a maximum freestream Mach number of 0.15 with scaled mass flows through the inlet for that condition. The data show that the pulsed actuation can reduce distortion from 29% to 4.6% as measured by the circumferential distortion descriptor DC60 using less than 1% of inlet mass flow. Closed loop control of the actuation was also demonstrated using a sidewall surface static pressure as the response sensor.

Gorton, Susan Althoff↗

NASA NTRSDate not supplied

Conceptual Integration Studies of Localized Active Flow Control on the Wing of a Commercial Aircraft

A study of conceptual integration and performance of localized active flow control technology onto wings of short-to-medium-range project passenger airplanes is summarized. Using predicted aerodynamic performance improvement opportunities on a computational fluid dynamics reference aircraft, this paper presents the estimated performance opportunities for conceptual implementation of studied wing localized active flow control technology for low-speed (takeoff and landing) application on a Project Research Aircraft configuration. Using conceptual active flow control systems and structural integration weight penalties for studied concepts, potential relevant net performance benefits can be obtained with reliable active flow control in takeoff and landing. The conceptual integration study identifies potential localized wing active flow control application opportunities for high-lift conditions using energy sources available on modern aircraft. Material benefits are estimated for takeoff and landing configurations for selected localized wing active flow control applications. The study concluded that substantial low-speed Maximum Lift and Lift/Drag related performance improvements may be possible with localized wing high-lift active flow control systems powered by auxiliary power unit, engine bleed, or electrical compressors - with due consideration of integration and weight impacts as well as availability requirements of such systems.

drag reduction↗

NASA NTRS2018

Active Flow Control for Trailing Edge Flap Separation

Active flow control (AFC) in the form of sweeping jet (SWJ) excitation and discrete steady jet excitation is used to control the flow separation on an NACA 0015 semispan wing with a deflected, simple-hinged, trailing edge flap. This geometry has been the focus of several recent publications that investigated methods to improve the efficiency of sweeping jet actuators. In the current study, the interaction of the AFC excitation with the separated flowfields present at several flap deflection angles was examined. Previous studies with this model have been limited to a maximum flap deflection angle of 40°. The flap deflection range was extended to 60! because systems studies have indicated that a high-lift system with simple-hinged flaps may require larger flap deflections than the Fowler flaps found on most high-lift systems. The results obtained at flap deflection angles of 20°, 40°, and 60° are presented and compared. Force and moment data, Particle Image Velocimetry (PIV) data, and steady and unsteady surface pressure data are used to describe the flowfield with and without AFC. With a flap deflection of 60°, increasing the SWJ actuator momentum at the flap shoulder increased lift due to an increase in circulation but did not completely eliminate the recirculation region above the flap surface. AFC using the discrete steady jet actuators of this study increased lift as well but required more mass flow than the SWJ actuators and had a detrimental effect on lift at the highest mass flow level tested. PIV results showed that the angle between the excitation and the flap surface was not optimal for attaching the separated shear layer.

Melton, LaTunia Pack↗

NASA NTRS1998

Overview of Active Flow Control at NASA Langley Research Center

The paper summarizes Active Flow Control projects currently underway at the NASA Langley Research Center. Technology development is being pursued within a multidisciplinary, cooperative approach, involving the classical disciplines of fluid mechanics, structural mechanics, material science, acoustics, and stability and control theory. Complementing the companion papers in this session, the present paper will focus on projects that have the goal of extending the state-of-the-art in the measurement, prediction, and control of unsteady, nonlinear aerodynamics. Toward this goal, innovative actuators, micro and macro sensors, and control strategies are considered for high payoff flow control applications. The target payoffs are outlined within each section below. Validation of the approaches range from bench-top experiments to wind-tunnel experiments to flight tests. Obtaining correlations for future actuator and sensor designs are implicit in the discussion. The products of the demonstration projects and design tool development from the fundamental NASA R&D level technology will then be transferred to the Applied Research components within NASA, DOD, and US Industry. Keywords: active flow control, separation control, MEMS, review

Pack, L. G.↗