Search NASA⌕ Search

SEARCH · Search NASA

Results for “Airborne Laser Scanning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

An Airborne Scanning Laser Altimetry Survey of Long Valley, California

Between 28 September and 7 October 1995, we conducted an airborne laser altimetry experiment over the Long Valley caldera, California, in which each of two scanning laser altimeters (dubbed SLICER and RASCAL) were flown in a NASA T-39 jet aircraft. Operating concurrently were a Global Positioning System (GPS) guidance system and dual frequency receivers for precise navigation and post-flight calculation or the airplane trajectory relative to a ground station, and an inertial navigation system (INS) for attitude determination. Reduction of raw laser ranges requires merging the differential kinematic GPS aircraft trajectory and the INS data with the laser data, and determination of the atmospheric delay. Data geolocation consists of obtaining the centre location and the mean elevation within each footprint in a geodetic coordinate system. The elevation of Crowley Lake is recovered to an accuracy of approximately 3 cm or better from 3 km above ground level and crossover analysis indicates that the elevation estimates are consistent from pass to pass. We test our geolocation procedures by comparing laser-derived elevations with those determined in situ for recognizable ground features. A comparison of laser and GPS-derived positions shows that the horizontal accuracy is better than the diameter of the footprint and vertical accuracy is within the error inherent in the range measurement. A comparison of SLICER elevation data with digital elevation models (DEMs) of the region shows that the DEM data provides surface topography to within stated accuracy limits. Although research continues to utilize the full potential of laser altimetry data, our results constitute a successful demonstration that the technique may be used to perform geodetic monitoring of surface topographic changes.

Hofton, M. A.↗
NASA NTRS1999

The Laser Vegetation Imaging Sensor (LVIS): A Medium-Altitude, Digitization-Only, Airborne Laser Altimeter for Mapping Vegetation and Topography

The Laser Vegetation Imaging Sensor (LVIS) is an airborne, scanning laser altimeter designed and developed at NASA's Goddard Space Flight Center. LVIS operates at altitudes up to 10 km above ground, and is capable of producing a data swath up to 1000 m wide nominally with 25 m wide footprints. The entire time history of the outgoing and return pulses is digitized, allowing unambiguous determination of range and return pulse structure. Combined with aircraft position and attitude knowledge, this instrument produces topographic maps with decimeter accuracy and vertical height and structure measurements of vegetation. The laser transmitter is a diode-pumped Nd:YAG oscillator producing 1064 nm, 10 nsec, 5 mJ pulses at repetition rates up to 500 Hz. LVIS has recently demonstrated its ability to determine topography (including sub-canopy) and vegetation height and structure on flight missions to various forested regions in the U.S. and Central America. The LVIS system is the airborne simulator for the Vegetation Canopy Lidar (VCL) mission (a NASA Earth remote sensing satellite due for launch in 2000), providing simulated data sets and a platform for instrument proof-of-concept studies. The topography maps and return waveforms produced by LVIS provide Earth scientists with a unique data set allowing studies of topography, hydrology, and vegetation with unmatched accuracy and coverage.

Blair, J. Bryan↗
NASA NTRS2000

Five Year Changes in Surface Elevations Of The Greenland Ice Sheet Measured by Aircraft Laser Altimetry

The Arctic Ice Mapping group (Project AIM) at NASA's Wallops Flight Facility has been conducting systematic topographic surveys of the Greenland Ice Sheet since 1993, using scanning airborne laser altimeters combined with GPS positioning technology. Flight lines were planned to cover all major ice drainage basins, with the intention to repeat the surveys after a 5-year interval in order to detect changes in the ice-sheet volume. The first resurvey was completed in June/July, 1998, along flight lines in the southern half of Greenland which had been first surveyed in 1993. The northern half of the ice sheet will be resurveyed in 1999. The resulting data sets will provide the first comprehensive examination of regional changes in the the surface elevation of the World's second largest ice sheet. This analysis includes the ice sheet fringe areas, which are expected to be much more climatically sensitive than the interior. Data will be presented which demonstrate the combination of the ATM (Airborne Topographic Mapper) sensors and GPS (Global Positioning System) yields measurements which are repeatable at the 10 cm level over baselines in excess of 1000 km.

Krabill, W. B.↗
NASA NTRS2004

Recent Observations of Increased Thinning of the Greenland Ice Sheet Measured by Aircraft GPS and Laser Altimetry

The Arctic Ice Mapping group (Project AIM) at the NASA Goddard Space Flight Center Wallops Flight Facility has been conducting systematic topographic surveys of the Greenland Ice Sheet (GIs) since 1993, using scanning airborne laser altimeters combined with Global Positioning System (GPS) technology onboard NASA's P-3 aircraft. Flight lines have covered all major ice drainage basins, with repeating surveys after a 5-year interval during the decade of the 90's. Analysis of this data documented significant thinning in many areas near the ice sheet margins and an overall negative mass balance of the GIS (Science, 2000). In 2001, 2002, and 2003 many of these flight lines were re-surveyed, providing evidence of continued or accelerated thinning in all observed areas around the margin of the GIs. Additionally, however, a highly-anomalous snowfall was observed between 2002 and 2003 in SE Greenland - perhaps an indicator of a shift in the regional climate?

Krabill, William B.↗
NASA NTRS2008

Recent Ice Sheet and Glacier Elevation Changes in Greenland from Aircraft Laser Altimetry

The Arctic Ice Mapping group (Project AIM) at the NASA Goddard Space Flight Center Wallops Flight Facility has been conducting systematic topographic surveys of the Greenland Ice Sheet (GIS) since 1993, using scanning airborne laser altimeters combined with Global Positioning System (UPS) technology. Earlier surveys showed the ice sheet above 2000-rn elevation to be in balance, but with localized regions of thickening or thinning. Thinning predominates at lower elevations and thinning rates have recently increased, resulting in a negative mass balance for the entire ice sheet. Recently, critical segments of near-coastal flight lines in Greenland were resurveyed. Results from the new data will be presented.

Krabill, William B.↗
NASA NTRS1998

development of a medium repetition rate (10 Hz - 500 Hz) diode pumped laser transmitter for airborne scanning altimetry

Since the late 1980's, NASA has developed several small, all-solid state lasers of low repetition rates for use as transmitters in prototype LIDAR and raster scanned altimetry retrieval systems. Our early laser transmitters were developed for high resolution airborne altimetry which employed cavity dumping techniques to produce a pulse shape with a 1 ns rise time. The first such laser was the SUMR (Sub-millimeter resolution) transmitter which used a side pumped, D-shaped half-rod of Nd:YAG for the oscillator active media and produced approximately 3 ns pulses of 100 micro-J energy at a 40 Hz repetition rate. (Coyle and Blair, 1993; Coyle et al., 1995) After several upgrades to improve rep rate and pulse energy, the final version produced 1.2 mJ pulses at 120 Hz with a 3.7 ns pulse width. The laser has become known as SPLT (Sharp Pulsed Laser Transmitter), and has flown successfully on a variety of airborne altimetry missions. (Coyle and Blair, 1995; Blair et al., 1994) From building these systems, we have accrued valuable experience in delivering field-deployable lasers and have become aware of the advantages and disadvantages of employing new technologies. For example, even though the laser's main operating environment is in a "cold" aircraft during flight, the laser must still operate in very warm temperatures. This is important if the mission is based in the desert or a tropical climate since ground calibration data from stationary targets must be gathered before and after each data flight. Because conductive cooling is much more convenient than closed loop water flow, achieving the highest possible laser efficiency is becoming a high priority when designing a flight laser. This is especially true for lasers with higher pulse energies and repetition rates which are needed for high altitude scanning altimeters and LIDARs.

Coyle, D. Barry↗
NASA NTRS2016

Lidar-Based Estimates of Above-Ground Biomass in the Continental US and Mexico Using Ground, Airborne, and Satellite Observations

Existing national forest inventory plots, an airborne lidar scanning (ALS) system, and a space profiling lidar system (ICESat-GLAS) are used to generate circa 2005 estimates of total aboveground dry biomass (AGB) in forest strata, by state, in the continental United States (CONUS) and Mexico. The airborne lidar is used to link ground observations of AGB to space lidar measurements. Two sets of models are generated, the first relating ground estimates of AGB to airborne laser scanning (ALS) measurements and the second set relating ALS estimates of AGB (generated using the first model set) to GLAS measurements. GLAS then, is used as a sampling tool within a hybrid estimation framework to generate stratum-, state-, and national-level AGB estimates. A two-phase variance estimator is employed to quantify GLAS sampling variability and, additively, ALS-GLAS model variability in this current, three-phase (ground-ALS-space lidar) study. The model variance component characterizes the variability of the regression coefficients used to predict ALS-based estimates of biomass as a function of GLAS measurements. Three different types of predictive models are considered in CONUS to determine which produced biomass totals closest to ground-based national forest inventory estimates - (1) linear (LIN), (2) linear-no-intercept (LNI), and (3) log-linear. For CONUS at the national level, the GLAS LNI model estimate (23.95 +/- 0.45 Gt AGB), agreed most closely with the US national forest inventory ground estimate, 24.17 +/- 0.06 Gt, i.e., within 1%. The national biomass total based on linear ground-ALS and ALS-GLAS models (25.87 +/- 0.49 Gt) overestimated the national ground-based estimate by 7.5%. The comparable log-linear model result (63.29 +/-1.36 Gt) overestimated ground results by 261%. All three national biomass GLAS estimates, LIN, LNI, and log-linear, are based on 241,718 pulses collected on 230 orbits. The US national forest inventory (ground) estimates are based on 119,414 ground plots. At the US state level, the average absolute value of the deviation of LNI GLAS estimates from the comparable ground estimate of total biomass was 18.8% (range: Oregon,−40.8% to North Dakota, 128.6%). Log-linear models produced gross overestimates in the continental US, i.e., N2.6x, and the use of this model to predict regional biomass using GLAS data in temperate, western hemisphere forests is not appropriate. The best model form, LNI, is used to produce biomass estimates in Mexico. The average biomass density in Mexican forests is 53.10 +/- 0.88 t/ha, and the total biomass for the country, given a total forest area of 688,096 sq km, is 3.65 +/- 0.06 Gt. In Mexico, our GLAS biomass total underestimated a 2005 FAO estimate (4.152 Gt) by 12% and overestimated a 2007/8 radar study's figure (3.06 Gt) by 19%.

Hybrid 3-Phase sampling↗
NASA NTRS2021

Three-dimensional estimation of deciduous forest canopy structure and leaf area using multi-directional, leaf-on and leaf-off airborne lidar data

Airborne laser scanning (ALS) has been widely used to map gap probability and leaf area index (LAI) distribution at plot and landscape scales. As an indirect measurement, most ALS methods to estimate LAI combine waveform or point density information with supporting field measurements such as the leaf angle distribution, gap probability, or direct LAI measures. The development of a more independent estimation approach would facilitate more widespread use of existing ALS data to investigate patterns of forest structure and build realistic 3-D vegetation scenes to simulate remote sensing imagery and energy balance. Here, we develop a data processing workflow (named PVlad) using ALS point cloud apparent reflectance to estimate LAI and voxel-based leaf area density (LAD), aiming to reduce the need for associated field measurements such as the gap probability. The adaptation of the path volume (PV) concept derived from apparent reflectance integrates information from multi-directional ALS pulses, and quantifies the percentage exploration of each voxel for classification and occlusion correction, such that rigorous volumetric sampling approaches can be developed to derive LAI and LAD. The PVlad workflow was applied to discrete-return lidar data (Riegl VQ480i) acquired by NASA Goddard's LiDAR, Hyperspectral and Thermal Imager (G-LiHT) Airborne Imager during leaf-on (summer) and leaf-off (spring) conditions at the Smithsonian Environmental Research Center (SERC). The estimates of LAI and LAD captured structural differences between mature, logged, and intermediate-aged stands over eight deciduous forest plots. The derived LAI values were compared to field litter collection measurements, and the derived LAD vertical distribution was compared to the output of the VoxLAD model using terrestrial laser scan (TLS) field survey data. Using voxel sizes ranging from 0.5 m to 5 m, overall LAI estimation showed linear fitting coefficient bias and for 1 and 2 m voxel sizes, and vertical LAD distribution showed strong correlation with and for 0.5 and 1m voxel sizes. For every forest stand, upper-canopy LAD had a low variance for voxel sizes of ≤ . Application of PVlad to the G-LiHT and other similar ALS data archives enables the development of fine-resolution LAI map products, including voxelization of LAD for ecosystem science and radiative transfer simulations of remote sensing imagery or surface energy balance.

Tiangang Yin↗
NASA NTRS2019

Long-Term Impacts of Selective Logging on Amazon Forest Dynamics from Multi-Temporal Airborne LiDAR

Forest degradation is common in tropical landscapes, but estimates of the extent and duration of degradation impacts are highly uncertain. In particular, selective logging is a form of forest degradation that alters canopy structure and function, with persistent ecological impacts following forest harvest. In this study, we employed airborne laser scanning in 2012 and 2014 to estimate three-dimensional changes in the forest canopy and understory structure and aboveground biomass following reduced-impact selective logging in a site in Eastern Amazon. Also, we developed a binary classification model to distinguish intact versus logged forests. We found that canopy gap frequency was significantly higher in logged versus intact forests even after 8 years (the time span of our study). In contrast, the understory of logged areas could not be distinguished from the understory of intact forests after 6–7 years of logging activities. Measuring new gap formation between LiDAR acquisitions in 2012 and 2014, we showed rates 2 to 7 times higher in logged areas compared to intact forests. New gaps were spatially clumped with 76 to 89% of new gaps within 5 m of prior logging damage. The biomass dynamics in areas logged between the two LiDAR acquisitions was clearly detected with an average estimated loss of -4.14 +/- 0.76 MgC/hay. In areas recovering from logging prior to the first acquisition, we estimated biomass gains close to zero. Together, our findings unravel the magnitude and duration of delayed impacts of selective logging in forest structural attributes, confirm the high potential of airborne LiDAR multitemporal data to characterize forest degradation in the tropics, and present a novel approach to forest classification using LiDAR data.

Pinage, Ekena Rangel↗
NASA NTRS2008

Relating a Spectral Index from MODIS and Tower-based Measurements to Ecosystem Light Use Efficiency for a Fluxnet-Canada Coniferous Forest

As part of the North American Carbon Program effort to quantify the terrestrial carbon budget of North America, we have been examining the possibility of retrieving ecosystem light use efficiency (LUE, the carbon sequestered per unit photosynthetically active radiation) directly from satellite observations. Our novel approach has been to compare LUE derived from tower fluxes with LUE estimated using spectral indices computed from MODIS satellite observations over forests in the Fluxnet-Canada Research Network, using the MODIS narrow ocean bands acquired over land. We matched carbon flux data collected around the time of the MODIS mid-day overpass for over one hundred relatively clear days in five years (2001-2006) from a mature Douglas fir forest in British Columbia. We also examined hyperspectral reflectance data collected diurnally from the tower in conjunction with the eddy correlation fluxes and meteorological measurements made throughout the 2006 growing season at this site. The tower-based flux data provided an opportunity to examine diurnal and seasonal LUE processes and their relationship to spectral indices at the scale of the forest stand. We evaluated LUE in conjunction with the Photochemical Reflectance Index (PRI), a normalized difference spectral index that uses 531 nm and a reference band to capture responses to high light induced stress afforded by the xanthophyll cycle. Canopy structure information, retrieved from airborne laser scanning radar (LiDAR) observations, was used to partition the forest canopy into sunlit and shaded fractions throughout the day, on numerous days during 2006. At each observation period throughout a day, the PRI was examined for the sunlit, shaded, and intermediate canopy segments defined by their instantaneous position relative to the solar principal plane (SPP). The sunlit sector was associated with the illumination "hotspot" (the reflectance backscatter maximum), the shaded sector with the "cold or dark spot" (the reflectance forward scatter minimum), while the intermediate, mixed sunlit/shade sector was located in the cross-plane to the SPP. The PRI indices clearly captured the differences in leaf groups, with sunlit foliage exhibiting the lowest values on sunny days throughout the 2006 season. When tower-based canopy-level LUE was recalculated to estimate foliage-based values (LUE(sub foilage) for the three foliage groups under their incident light environments, a strong linear relationship for PRI:LUE(sub foilage) was demonstrated (0.6 less than or equal to r(sup 2) less than or equal to 0.8, n=822, P<0.0001). The MODIS data represent relatively large areas when acquired at nadir (approx.1 sq km) or at variable off-nadir view angles (greater than or equal to 1 sq km) looking forward or aft. Nevertheless, a similar relationship between MODIS PRI and tower-based LUE was obtained from satellite observations (r(sup 2) = 0.76, n=105, P= 0.026) when the azimuth offsets from the SPP for off-nadir observations were considered. At this relatively high latitude of 50 degrees, the MODIS directional observations were offset from the SPP by approximately 50 degrees, but still represented backscatter or forward scatter sectors of the bidirectional reflectance distribution function (BRDF). The backscatter observations sampled the sunlit forest and provided lower PRI values, in general, than the forward scatter observations from the shaded forest. Since the hotspot and darkspot were not typically directly observed, the dynamic range for MODIS PRI was less than that observed in the SPP at the canopy level; therefore, MODIS PRI values were more similar to those observed in sifu in the BRDF cross-plane. While not ideal in terms of spatial resolution or optimal viewing configuration, the MODIS observations nevertheless provide a means to monitor forest under stress using narrow spectral band indices and off-nadir observations. This research has stimulated several spin-off studies for remote sensinf LUE, and demonstrates the importance of the connection between ecosystem structure and physiological function.

Middleton, Elizabeth M.↗
NASA NTRS2012

Combined Use of Airborne Lidar and DBInSAR Data to Estimate LAI in Temperate Mixed Forests

The objective of this study was to determine whether leaf area index (LAI) in temperate mixed forests is best estimated using multiple-return airborne laser scanning (lidar) data or dual-band, single-pass interferometric synthetic aperture radar data (from GeoSAR) alone, or both in combination. In situ measurements of LAI were made using the LiCor LAI-2000 Plant Canopy Analyzer on 61 plots (21 hardwood, 36 pine, 4 mixed pine hardwood; stand age ranging from 12-164 years; mean height ranging from 0.4 to 41.2 m) in the Appomattox-Buckingham State Forest, Virginia, USA. Lidar distributional metrics were calculated for all returns and for ten one meter deep crown density slices (a new metric), five above and five below the mode of the vegetation returns for each plot. GeoSAR metrics were calculated from the X-band backscatter coefficients (four looks) as well as both X- and P-band interferometric heights and magnitudes for each plot. Lidar metrics alone explained 69% of the variability in LAI, while GeoSAR metrics alone explained 52%. However, combining the lidar and GeoSAR metrics increased the R2 to 0.77 with a CV-RMSE of 0.42. This study indicates the clear potential for X-band backscatter and interferometric height (both now available from spaceborne sensors), when combined with small-footprint lidar data, to improve LAI estimation in temperate mixed forests.

leaf area index↗
NASA NTRS2016

Scaling Estimates of Vegetation Structure in Amazonian Tropical Forests Using Multi-Angle MODIS Observations

Detailed knowledge of vegetation structure is required for accurate modelling of terrestrial ecosystems, but direct measurements of the three dimensional distribution of canopy elements, for instance from LiDAR, are not widely available. We investigate the potential for modelling vegetation roughness, a key parameter for climatological models, from directional scattering of visible and near-infrared (NIR) reflectance acquired from NASA's Moderate Resolution Imaging Spectroradiometer (MODIS). We compare our estimates across different tropical forest types to independent measures obtained from: (1) airborne laser scanning (ALS), (2) spaceborne Geoscience Laser Altimeter System (GLAS)/ICESat, and (3) the spaceborne SeaWinds/QSCAT. Our results showed linear correlation between MODIS-derived anisotropy to ALS-derived entropy (r(exp 2)= 0.54, RMSE= 0.11), even in high biomass regions. Significant relationships were also obtained between MODIS-derived anisotropy and GLAS-derived entropy(0.52 less than or equal to r(exp 2) less than or equal to 0.61; p less than 0.05), with similar slopes and offsets found throughout the season, and RMSE between 0.26 and 0.30 (units of entropy). The relationships between the MODIS-derived anisotropy and backscattering measurements (sigma(sup 0)) from SeaWinds/QuikSCAT presented an r(exp 2) of 0.59 and a RMSE of 0.11. We conclude that multi-angular MODIS observations are suitable to extrapolate measures of canopy entropy across different forest types, providing additional estimates of vegetation structure in the Amazon.

MODIS↗
NASA NTRS2001

Remote Sensing of Wind Fields and Aerosol Distribution with Airborne Scanning Doppler Lidar

The coherent Doppler laser radar (lidar), when operated from an airborne platform, is a unique tool for the study of atmospheric and surface processes and features. This is especially true for scientific objectives requiring measurements in optically-clear air, where other remote sensing technologies such as Doppler radar are typically at a disadvantage. The atmospheric lidar remote sensing groups of several US institutions, led by Marshall Space Flight Center, have developed an airborne coherent Doppler lidar capable of mapping the wind field and aerosol structure in three dimensions. The instrument consists of an eye-safe approx. 1 Joule/pulse lidar transceiver, telescope, scanner, inertial measurement unit, and flight computer system to orchestrate all subsystem functions and tasks. The scanner is capable of directing the expanded lidar beam in a variety of ways, in order to extract vertically-resolved wind fields. Horizontal resolution is approx. 1 km; vertical resolution is even finer. Winds are obtained by measuring backscattered, Doppler-shifted laser radiation from naturally-occurring aerosol particles (of order 1 micron diameter). Measurement coverage depends on aerosol spatial distribution and composition. Velocity accuracy has been verified to be approx. 1 meter per second. A variety of applications have been demonstrated during the three flight campaigns conducted during 1995-1998. Examples will be shown during the presentation. In 1995, boundary layer winds over the ocean were mapped with unprecedented resolution. In 1996, unique measurements were made of. flow over the complex terrain of the Aleutian Islands; interaction of the marine boundary layer jet with the California coastal mountain range; a weak dry line in Texas - New Mexico; the angular dependence of sea surface scattering; and in-flight radiometric calibration using the surface of White Sands National Monument. In 1998, the first measurements of eyewall and boundary layer winds within a hurricane were made with the airborne Doppler lidar. Potential applications and plans for improvement will also be described.

Rothermel, Jeffry↗
NASA NTRS1998

Holographic Airborne Rotating Lidar Instrument Experiment (HARLIE)

Scanning holographic lidar receivers are currently in use in two operational lidar systems, PHASERS (Prototype Holographic Atmospheric Scanner for Environmental Remote Sensing) and now HARLIE (Holographic Airborne Rotating Lidar Instrument Experiment). These systems are based on volume phase holograms made in dichromated gelatin (DCG) sandwiched between 2 layers of high quality float glass. They have demonstrated the practical application of this technology to compact scanning lidar systems at 532 and 1064 nm wavelengths, the ability to withstand moderately high laser power and energy loading, sufficient optical quality for most direct detection systems, overall efficiencies rivaling conventional receivers, and the stability to last several years under typical lidar system environments. Their size and weight are approximately half of similar performing scanning systems using reflective optics. The cost of holographic systems will eventually be lower than the reflective optical systems depending on their degree of commercialization. There are a number of applications that require or can greatly benefit from a scanning capability. Several of these are airborne systems, which either use focal plane scanning, as in the Laser Vegetation Imaging System or use primary aperture scanning, as in the Airborne Oceanographic Lidar or the Large Aperture Scanning Airborne Lidar. The latter class requires a large clear aperture opening or window in the aircraft. This type of system can greatly benefit from the use of scanning transmission holograms of the HARLIE type because the clear aperture required is only about 25% larger than the collecting aperture as opposed to 200-300% larger for scan angles of 45 degrees off nadir.

Schwemmer, Geary K.↗
NASA NTRS1994

Comparison of radar-altimetry data over Greenland with surface topography derived from airborne laser altimetry

During the Summers of 1991, 1992, and 1993, NASA flew a scanning laser altimeter over transects of the Greenland ice sheet. Airplane location was measured precisely using differential Global Positioning System (GPS) surveying techniques. This allowed all altimetry data to be reduced to an estimate of ice surface elevations relative to the Earth ellipsoid. Repeat flights over the same areas indicate data consistency to 10 to 20 cm. Many of the aircraft flights were made along the ERS-1 'radar-altimeter footprint track' for a commissioning phase orbit. Rigorous comparison between the ERS-1 altimeter measurements and those from the laser altimeter will require analysis of individual ERS-1 altimeter waveforms, and since the information needed to do this is not yet available, results from comparison of TOPEX (Topology Ocean Experiment) Poseidon (T/P) radar altimetry data with laser data obtained at the northernmost limit of the T/P orbits are presented.

Thomas, R. H.↗