Search NASA⌕ Search

SEARCH · Search NASA

Results for “Alloy 718”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

An investigation of squeeze-cast alloy 718

Alloy 718 billets produced by the squeeze-cast process have been evaluated for use as potential replacements for propulsion engine components which are normally produced from forgings. Alloy 718 billets were produced using various processing conditions. Structural characterizations were performed on 'as-cast' billets. As-cast billets were then homogenized and solution treated and aged according to conventional heat-treatment practices for this alloy. Mechanical property evaluations were performed on heat-treated billets. As-cast macrostructures and microstructures varied with squeeze-cast processing parameters. Mechanical properties varied with squeeze-cast processing parameters and heat treatments. One billet exhibited a defect free, refined microstructure, with mechanical properties approaching those of wrought alloy 718 bar, confirming the feasibility of squeeze-casting alloy 718. However, further process optimization is required, and further structural and mechanical property improvements are expected with process optimization.

Gamwell, W. R.↗
NASA NTRS2018

Impact of Powder Variability on the Microstructure and Mechanical Behavior of Selective Laser Melted (SLM) Alloy 718

Nickel Alloy 718 has found wide use in high-temperature aerospace applications (up to 700°C), due to a combination of good mechanical properties, environmental resistance, and workability at moderate cost. These properties have led Alloy 718 to early adoption by selective laser melting (SLM) additive manufacturing. This presentation will share results from a comprehensive industry survey of 718 powder feedstock for SLM. The survey focuses on the impact of variability in powder characteristics on build quality, microstructure, tensile and high cycle fatigue in the as-fabricated and machined surface conditions. The investigation includes sixteen powder lots from eight suppliers that are produced by gas atomization or rotary atomization in argon or nitrogen. This research was previously presented and published at the 9th International Symposium on Superalloy 718 & Derivatives and was funded by NASA Space Launch System Liquid Engine Office with the Human Exploration Operations Mission Directorate.

Sudbrack, Chantal↗
NASA NTRS1990

Magnetic susceptibility of Inconel alloys 718, 625, and 600 at cryogenic temperatures

After a hydrogen fuel bleed valve problem on the Discovery Space Shuttle was traced to the strong magnetization of Inconel 718 in the armature of the linear variable differential transformer near liquid hydrogen temperatures, the ac magnetic susceptibility of three samples of Inconel 718 of slightly different compositions, one sample of Inconel 625, and on sample of Inconel 600 were measured as a function of temperature. Inconel 718 alloys are found to exhibit a spin glass state below 16 K. Inconel 600 exhibits three different magnetic phases, the lowest-temperature state (below 6 K) being somewhat similar to that of Inconel 718. The magnetic states of the Inconel alloys and their magnetic susceptibilities appear to be strongly dependent on the exact composition of the alloy.

Goldberg, Ira B.↗
NASA NTRS1967

Materials data handbook, Inconel alloy 718

Materials data handbook on Inconel alloy 718 includes data on the properties of the alloy at cryogenic, ambient, and elevated temperatures and other pertinent engineering information required for the design and fabrication of components and equipment utilizing this alloy.

Sessler, J.↗
NASA NTRSDate not supplied

Impact of Powder Supply Variation on Mechanical Properties for Additive Manufacture of Alloy 718

The Additive Manufacturing Structural Integrity Initiative (AMSII) examined how a number of different Alloy 718 powder lots can create variation in microstructure and mechanical properties in parts fabricated using Laser Powder Bed Fusion. Being a common alloy, Alloy 718 powder can be found in a variety of compositions, fabrication techniques, and powder size distribution. Sixteen virgin powders, and three recycled powders were used to build samples for microstructure analysis, fatigue and tensile testing. The major impacts of the different powders manifested in variations in the microstructure, such as minor phases and grain size variation. There were corresponding variations in mechanical properties. A down-selection of powders were chosen for additional analysis, and a powder recyclability study was completed to look at the effect of reused powder.

Alloy 718↗
NASA NTRS1986

The effect of heat treatment on microfissuring in alloy 718

Changes in the microfissuring susceptibility of alloy 718 due to solution annealing and age hardening are studied. The effects of Ni3Nb (delta) precipitation during solution annealing and gamma-prime + gamma-double-prime precipitation during age hardening on microfissuring are investigated. It is observed that solution annealing reduces microfissuring and age hardening increases it, and the two precipitates do not affect microfissuring susceptibility. Potential causes for the detected intergranular segregation of the alloy are discussed.

Thompson, R. G.↗
NASA NTRS1976

Annealing strained alloy 718

Report shows that grain coarsening in Alloy 718 can result in greatly reduced resistance to weld-heat-produced zone fissuring, especially when final grain size is ASTM 2. Tensile tests and metallographic examination of bend test specimens provide necessary data.

Morrison, T. J.↗
NASA NTRS1991

An evaluation of GTAW-P versus GTA welding of alloy 718

Mechanical properties were evaluated to determine statistically whether the pulsed current gas tungsten arc welding (GTAW-P) process produces welds in alloy 718 with room temperature structural performance equivalent to current Space Shuttle Main Engine (SSME) welds manufactured by the constant current GTAW-P process. Evaluations were conducted on two base metal lots, two filler metal lots, two heat input levels, and two welding processes. The material form was 0.125-inch (3.175-mm) alloy 718 sheet. Prior to welding, sheets were treated to either the ST or STA-1 condition. After welding, panels were left as welded or heat treated to the STA-1 condition, and weld beads were left intact or machined flush. Statistical analyses were performed on yield strength, ultimate tensile strength (UTS), and high cycle fatigue (HCF) properties for all the post welded material conditions. Analyses of variance were performed on the data to determine if there were any significant effects on UTS or HCF life due to variations in base metal, filler metal, heat input level, or welding process. Statistical analyses showed that the GTAW-P process does produce welds with room temperature structural performance equivalent to current SSME welds manufactured by the GTAW process, regardless of prior material condition or post welding condition.

Gamwell, W. R.↗
NASA NTRS1972

Materials data handbook: Inconel alloy 718

A summary of the materials property information for Inconel alloy 718 is presented. The scope of the information includes physical and mechanical properties at cryogenic, ambient, and elevated temperatures. Information on material procurement, metallurgy of the alloy, corrosion, environmental effects, fabrication, and joining techniques is developed.

Muraca, R. F.↗
NASA NTRS1998

A Size Effect on the Fatigue Crack Growth Rate Threshold of Alloy 718

Fatigue crack growth rate (FCGR) tests were conducted on Alloy 718 in the solution annealed and aged condition at room temperature. In each test, the FCGR threshold was measured using the decreasing (Delta)K method. Initial testing was at two facilities, one of which used C(T) specimens with W = 127 mm. Previous data at the other facility had been obtained with specimens with W = 50.8 mm. A comparison of test results at R = 0.1 showed that the threshold for the 127 mm specimen was considerably higher than that of the 50.8 mm specimen. A check showed that this difference was not due to a heat-to-heat or lab-to-lab variation. Additional tests were conducted on specimens with W = 25.4 mm and at other R values. Data for the various specimens is presented along with parameters usually used to describe threshold behavior.

Garr, K. R.↗
NASA NTRS1985

Relationships between microstructure and microfissuring in alloy 718

Microfissures which occur in the weld heat affected zone of alloy 718 can be a limiting factor in the material's weldability. Several studies have attempted to relate microfissuring susceptibility to processing conditions, microstructure, and/or heat-to-heat chemistry differences. The present investigation studies the relationships between microstructure and microfissuring by isolating a particular microstructural feature and measuring microfissuring as a function of that feature. Results to date include the identification of a microstructure-microfissure sequence, microfissuring susceptibility as a function of grain size, and microfissuring susceptibility as a function of solution annealing time.

Thompson, R. G.↗
NASA NTRS1985

Effect of reduction of strategic Columbium addition in 718 Alloy on the structure and properties

A series of alloys was developed having a base composition similar to Inconel 718, with reduced Cb levels of 3.00 and 1.10 wt% Cb. Substitutions of 3.0% W, 3.0W + 0.9V or Mo increased from 3.0% to 5.8% were made for the Cb in these alloys. Two additional alloys, one containing 3.49% Cb and 1.10% Ti and another containing 3.89% Cb and 1.29% Ti were also studied. Tensile properties at rooom and elevated temperatures, stress-rupture tests, and an analysis of extracted phases were carried out for each of the alloys. Additions of solid solution elements to a reduced Cb alloy had no significant effect on the properties of the alloys under either process condition. The solution and age alloys with substitutions of 1.27% i at 3.89% Cb had tensile properties similar top hose of the original alloy and stress-rupture properties superior to the original alloy. The improved stress-rupture properties were the result of significant precipitation of Ni3Ti-gamma prime in the alloy, which is more stable than gamma' at the elevated temperatures. At lower temperatures, the new alloy benefits from gamma' strengthening. With more precise control and proper processing, the reduced Cb direct-age alloy could substitute for Alloy 718 in high strength applications.

Ziegler, K. R.↗
NASA NTRS2018

Impact of Powder Variability on the Microstructure and Mechanical Behavior of Selective Laser Melted Alloy 718

Powder-bed additive manufacturing processes use fine powders to build parts layer-by-layer. Alloy 718 powder feedstocks for selective laser melting (SLM) additive manufacturing are produced commercially by both gas and rotary atomization and are available typically in the 10-45 or 15-45 microns size ranges. A comprehensive investigation was conducted to understand the impact of powder variability on the microstructure and mechanical behavior of SLM 718 heat treated to Aerospace Material Specification (AMS) 5664. This study included sixteen virgin powders and three once-recycled powders within the 10-45 and 15-45 microns size ranges that were obtained from seven direct source suppliers and one reseller. Although alike as highly regular spheroids, these powders showed distinct differences in composition (especially Al, C and N contents), particle size distributions, and powder features such as degree of agglomeration, fusion and surface roughness. Compositional differences expectedly had the strongest impact on microstructure. High N and C contents formed TiN-nitrides and/or (Nb,Ti,Mo)-C carbides on the grain boundaries, prevented recrystallization during heat treatment, and resulted in retained (001)-scalloped shaped grains that ranged from 19 to 41 microns in average size. In the absence of this particle pinning, the average grain size of the heat treated SLM 718 ranged from 51 microns to 90 microns. Room temperature tensile and high cycle fatigue (HCF) testing compared as-fabricated (AF) and low stress ground (LSG) surface conditions. Tensile testing revealed consistent behavior between the two surface conditions and amongst the powder lots. The finer grained SLM 718 builds displayed the lowest tensile properties. A SLM 718 build fabricated from a powder with eight times lower C content showed statistically better tensile properties presumably due to enhanced coarsening of (delta)-Ni3Nb precipitates. The specimens from once-recycled powders had slightly higher tensile strengths and slightly higher ductility compared to their virgin equivalents; once-recycling also did not substantially degrade the mean HCF life. The LSG fatigue lives agreed with conventionally manufactured 718 data, while AF lives exhibited a knock-down due to surface roughness. The fatigue lives of AF specimens were statistically equivalent across powder lots except for one and failures typically initiated at stress concentrators associated with SLM surface asperities. Fatigue testing of low stress ground specimens result in both transgranular and within facet crack initiations. More than half of the cracks initiated from these facets for the machined condition; however, these facets appeared to be within grains that were larger-than-average in size. A nitrogen-atomized powder with fine prior particles of TiN-nitrides and M(Ti,Nb,Mo)C carbides from atomization on powder surfaces resulted in the best fatigue performance with segregation of these particles to the SLM 718 grain boundaries leading to higher resistance to early-stage crack propagation. Typically the fine-grained builds with minor phases along the grain boundaries did not perform well in fatigue, whereas a larger-grain build with lower carbon content and coarser delta-Ni3Nb precipitates showed the next best HCF response. Further details of the build microstructure and its impact on tensile and fatigue behavior was considered.

laser deposition↗
NASA NTRS2019

Discerning the Impact of Powder Feedstock Variability on Structure, Property, and Performance of Selective Laser Melted Alloy 718: A Principal Component Analysis (PCA) of Feedstock Variability

Extensive mechanical, chemical and microstructural analyses were conducted on additively manufactured Alloy 718 to characterize powders from multiple vendors to determine the effects of variations observed in the powders had on the consolidated material. With over 190 variables examined, it was necessary to reduce the number of variables and identify the variables and classes of variables that had the greatest effect. Principle Component Analysis (PCA) was used to reduce the number of variable to effectively 12 while identifying several classes of variables as most important.

Ellis, David↗
NASA NTRS2017

Relationship of Powder Feedstock Variability to Microstructure and Defects in Selective Laser Melted Alloy 718

Powder-bed additive manufacturing processes use fine powders to build parts layer by layer. For selective laser melted (SLM) Alloy 718, the powders that are available off-the-shelf are in the 10-45 or 15-45 micron size range. A comprehensive investigation of sixteen powders from these typical ranges and two off-nominal-sized powders is underway to gain insight into the impact of feedstock on processing, durability and performance of 718 SLM space-flight hardware. This talk emphasizes an aspect of this work: the impact of powder variability on the microstructure and defects observed in the as-fabricated and full heated material, where lab-scale components were built using vendor recommended parameters. These typical powders exhibit variation in composition, percentage of fines, roughness, morphology and particle size distribution. How these differences relate to the melt-pool size, porosity, grain structure, precipitate distributions, and inclusion content will be presented and discussed in context of build quality and powder acceptance.

Characterization↗