Search NASA⌕ Search

SEARCH · Search NASA

Results for “Arrhenius plot”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Outgassing measurements of bare and magnetite-coated low-carbon steel vacuum chambers

The outgassing properties of bare and magnetite-coated AISI 1020 low-carbon steel vacuum chambers were evaluated to establish material selection criteria for extreme high vacuum applications, namely, to explore the possibility of using these materials to build next-generation spin-polarized photoelectron guns. Water outgassing measurements using the throughput method revealed that the magnetite-coated chamber exhibited five times lower outgassing at room temperature prior to baking, but this advantage disappears after 80 °C baking. Hydrogen outgassing measurements demonstrated significant differences after intensive heat treatment: the bare low-carbon steel vacuum chamber achieved a specific outgassing rate of 9.6 × 10 −16 Torr L s −1 cm −2 after 400 °C/50 h bake plus additional heat treatment at lower temperatures, 25 times lower than the magnetite-coated low-carbon steel chamber. Residual gas analysis showed >99% hydrogen composition after heat treatment for both materials, with carbon species below detection limits for bare low-carbon steel versus 0.8% for magnetite-coated surfaces. These measurements indicate that properly conditioned bare low-carbon steel can achieve the <10 −12 Torr pressures required for next-generation spin-polarized photogun applications. In conclusion, the paper includes various analysis techniques intended to explain observed behaviors: isotherm analysis of pump-down plots, Arrhenius analysis of hydrogen outgassing rate data, and residual gas composition tracking.

Adsorption isotherm↗
DOE OSTI2020

Determination of neutron irradiation temperatures of SiC using electrical resistivity method

The irradiation temperature of silicon carbide (SiC) was determined post-irradiation by examination of the recovery of the electrical resistivity due to thermal annealing in a rapid heating/cooling optical furnace. High-purity, high-resistivity grade SiC is routinely used as a passive temperature monitor in neutron irradiation studies at the High Flux Isotope Reactor (HFIR), and this paper presents an alternative automated technique for determination of the irradiation temperature the SiC experienced. Neutron collisions with the atoms results in displaced lattice atoms (interstitials) that act as electron donors yielding a significant decrease in electrical resistivity. The irradiation defects become thermodynamically unstable and start to recombine, when annealed above the irradiation temperature, resulting in a recovery of the electrical resistivity. The resistivity is measured at a fixed elevated temperature above ambient, which is below the target irradiation temperature. When the resistivity is plotted as a function of annealing temperatures, a clear increase is observed due to the recovery of irradiation defects. We have demonstrated that this electrical resistivity measurement of SiC is effective to determine irradiation temperature of SiC. In conclusion, energy levels of various defects in SiC were calculated from Arrhenius plots of electrical conductivity versus inverse temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Ionic Liquid Sheath Stabilizes Atomically Dispersed Reduced Graphene Aerogel‐Supported Iridium Complexes during Ethylene Hydrogenation Catalysis

Abstract An atomically dispersed reduced graphene aerogel (rGA)‐supported iridium catalyst having reactive ethylene ligands was synthesized at an iridium loading of 9.9 wt % and coated with an ionic liquid, 1‐ethyl‐3‐methylimidazolium acetate ([EMIM][OAc]). Continuous‐scan X‐ray absorption spectra demonstrated that the iridium remained site‐isolated in flowing equimolar C 2 H 4 and H 2 during a temperature ramp to 100 °C. The data further showed the lack of detectable iridium aggregation when the feed was H 2 ‐rich or even pure H 2 at 100 °C. An Arrhenius plot determined for ethylene hydrogenation catalysis with the sample in flowing equimolar ethylene and hydrogen showed no variation in the apparent activation energy at temperatures up to 100 °C, confirming that the active sites remained intact at the higher temperatures. The results point to opportunities for overcoming the stability limitations of atomically dispersed supported noble metal catalysts by choice of electron‐donor supports and ionic liquid sheaths.

Kurtoğlu‐Öztulum, Samira F.↗
DOE OSTI2026

Catalytic resonance theory for the kinetics of photon-promoted catalysis

The illumination of catalytic surfaces with a continuous or pulsed stream of photons dynamically modulates surface chemistry for faster rates, non-equilibrium conversion, or product selectivity control. To establish fundamental principles of dynamic photon-modulated catalysis, the photocatalytic conversion of a generic surface reaction was simulated using the kinetic Monte Carlo method to understand the kinetic implications of an independent stream of photons that promotes surface product desorption. The time-averaged photocatalytic rate at differential conditions for varying photon flux and temperatures indicated three kinetic regimes described by product thermal desorption control, surface reaction control, and an intermediate kinetic regime with a zero slope Arrhenius plot, consistent with a degree of rate control dominated by the photon arrival frequency (i.e., per-site photon flux). Here, the maximum photocatalytic rate occurred orders of magnitude above the Sabatier limit at the resonance frequency, identified as the photon arrival frequency matching the surface reaction rate constant.

Canavan, Jesse R. [University of Minnesota, Minnea↗
DOE OSTI2022

Mechanistic study of chemical looping reactions between solid carbon fuels and CuO

Copper (Cu) based chemical-looping combustion (CLC) is a promising process that utilizes solid carbon fuel such as coal and biomass. Understanding the reaction kinetics in this process can facilitate the industrial design of CLC units. Here, in this work, molecular dynamics (MD) simulations were performed to investigate the reaction kinetics of n-butane and two simplified solid carbon fuels (lignite and anthracite) with/without copper oxide (CuO) nanoparticle. In addition, experiments were conducted on the thermal characteristics, flammability, and flame speeds of CuO and solid carbon mixtures. For n-butane, oxidation on the CuO surface is the primary reaction since the activation energy of the surface reaction is much lower than that of oxygen (O 2 ) combustion (9.2 vs. 53.3 kcal/mol). On the other hand, for lignite, there is a smaller difference in the activation energy of O 2 combustion and surface reaction (23.04 vs. 6.34 kcal/mol). We hypothesize that some solid carbon fuels can have different reaction kinetics dependent upon temperature. This is proven by the case of a simplified anthracite coal: an Arrhenius plot shows that this solid carbon fuel has two different reaction kinetic regimes and the critical temperature for the change in kinetics is related to the oxygen uncoupling of the CuO nanoparticle. Like the modeling simulations, a change in activation energy is observed in the experimental results, where desorption of molecular oxygen from CuO becomes important.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Electrochemical, thermodynamic, and physical properties of tetradecyltrihexylphosphonium ([P 6,6, 6,14 ] + ) and methyl-propyl piperidinium containing ionic liquids and their propylene carbonate solutions

Here, the viscosity, conductivity, electrochemical window and related thermodynamic properties such as excess volume and dynamic viscosity deviation of two phosphonium ionic liquids were measured and calculated for “as-supplied” and dried neat liquids and also v/v mixtures of 99/1, 95/5, 90/10, 75/25, and 50/50 of the ionic liquids with propylene carbonate (PC). Tetradecyltrihexylphosphonium dicyanamide ([P 6,6,6,14 ] + dicyanamide), Cyphos 105, and tetradecyltrihexylphosphonium bis(trifluororomethanesulfonyl)imide (called bistriflimide) ([P 6,6,6,14 ] + bistriflimide), Cyphos 109, ionic liquids were studied. Generally speaking, there were slight differences in the measured properties of the wet and dried IL solutions which were reflected in differences if the calculated properties. The measured and calculated properties were compared with those collected and derived from a piperidinium-based ionic liquid, methyl-propyl piperidinium bistriflimide. Arrhenius plots for both the viscosity and conductivity were linear, with the linearity of the Litovitz plots being slightly higher. The viscosity and conductivity of the phosphonium solutions yielded Walden Plots that differed from Walden plots of piperidinium solutions and other ionic liquid solutions. For the phosphonium based ionic liquids, the ionicity was found to increase with increasing dilution in propylene carbonate. The electrochemical windows of the ionic liquids were determined as a function of the concentration of the ionic liquid present in the solution. The size of the window generally initially decreased and then increased with the addition of PC for the [P 6,6,6,14 ] + dicyanamide ionic liquid increasing from 3.4 V in the 95/5 v/v (volume Cyphos 105) to volume of PC solvent) to 3.7 in the 50/50 dried IL case. The electrochemical windows of the dried liquids were slightly larger 3.5 V for the 95/5 v/v and 4.2 V for the 50/50 v/v Cyphos 105/PC solutions. The electrochemical window was larger and the conductivity was higher for the piperidinium IL solutions, but since the ionicity increases with dilution, the phosphonium based IL solutions may prove favorable for processes such as electrochemical reduction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Catalytic Resonance Theory: Experimental and Kinetic Interpretation of Programmable Catalysis

The complexity of programmable catalysts that change in the physical or electronic state on the time scale of a catalytic turnover results in uncertainty in the kinetic outcome of common measurements with dynamic catalyst experiments. To provide an interpretation of utility to experimentalists, a general programmable catalytic reaction exhibiting high turnover efficiency was simulated to understand the kinetic behavior of catalysts with varying frequency, binding energy, oscillation amplitude, and minimum oscillation binding energy at different temperatures and reactant gas pressures. The time-averaged catalytic rate for varying temperature in the form of an Arrhenius plot exhibited three distinct kinetic regimes, with the intermediate temperatures or applied frequencies exhibiting zero slope, indicative of barrier-free kinetic control. Transitions in experimentally measurable kinetic regimes with both temperature and applied catalyst oscillation frequency were associated with transitions in the sensitivity of reaction rate constants and degrees of rate control. Furthermore, these distinct kinetic macroscopic features specific to programmable catalysts were identified for observation in experimental dynamic kinetic measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Kinetic analyses for solid-state phase transition of metastable amorphous-AlO x (2.5 < x ≤ 3.0) nanostructures into crystalline alumina polymorphs

Solid-solid phase change materials (SS-PCMs) hold promise for energy storage/dissipation in batteries and energetic materials. Yet, phase change kinetics for SS-PCMs undergoing metastable to semi-stable/stable phase transformations remain relatively ill-studied because trapping metastable phases remain challenging. Recently, we demonstrated the kinetic entrapment and stabilization of a highly disordered and amorphous Al-oxide phase m-AlO x @C (x~2.5-3.0) via laser ablation synthesis in solution (LASiS). We report here, to our knowledge, the first chemical kinetics analysis for S-S phase transition of the m-AlO 3 @C nanocomposites (< 5–8 nm sizes) into semi-stable equilibrium alumina phases (θ/γ-Al 2 O 3 ) via disproportionation reaction, while releasing excess trapped gases. Our results indicate the atomic density of the AlO 3 structures to be ~5–10 times less than that of the final Al 2 O 3 phases, which led to the hypothesis of a volume shrinkage process during their phase transition. Temperature-dependent X-ray diffraction studies reveal the high-temperature phase transition for m-AlO 3 → θ/γ-Al 2 O 3 to follow contracting volume kinetics model, thereby validating our earlier hypothesis. Using the geometric volume contraction model, reaction kinetics analyses from Arrhenius plots reveal the activation energy barrier for the phase transition to be ~270±11 kJ/mol. This makes the activation energy barrier nearly identical to the oxidation of micron-sized Al particles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Evaluating steam oxidation kinetics of environmental barrier coatings

Environmental barrier coatings (EBCs) are a commercially proven means of protecting SiC-based materials in gas turbine environments. However, there are little specific data in the literature on the impact of coatings like Yb 2 Si 2 O 7 on preventing accelerated SiO 2 growth in the presence of H 2 O. Quantification of reduced rates are necessary for evaluating and comparing EBC effectiveness and incorporation of silica growth rates into future EBC lifetime models. In this study, baseline kinetics of silica formation on bare Si and chemically vapor deposited (CVD) SiC in the 1250–1425 °C range were obtained via 100 h isothermal exposures in dry air and steam environments utilizing a SiC reaction tube to mitigate specimen volatility. An Arrhenius plot of the resulting rates was constructed, representing baseline minimum and maximum rates for Si and SiC oxidation at ambient pressure. Various EBC systems on CVD SiC substrates including air plasma sprayed (APS) EBCs with and without a Si bond coating and with surface roughening to enhance Yb 2 Si 2 O 7 adhesion were subjected to 1-h furnace cycle testing in air with 90vol%H 2 O at 1250–1350°C for up to 500 cycles. After exposure, silica formation rates were measured and compared to the baseline rates to assess EBC effectiveness, where EBC effectiveness is gauged as the propensity to reduce underlying rates of silica formation. With a Si bond coating, a ~180 µm Yb 2 Si 2 O 7 (YbDS) top coating reduced rates over the entire 1250°-1350°C range. Without a Si bond coating, ~60 µm (YbDS) coatings deposited directly onto CVD SiC exhibited poor adhesion, and had to be deposited onto substrates with enhanced roughness at 1350°C. Finally, while exhibiting good adhesion at 1350°C, overall the single layer YbDS coating exhibited a decreasing effectiveness from 1250° to 1350°C.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Final-stage densification kinetics of direct current–sinteredZrB2

Final-stage sintering was analyzed for nominally phase pure zirconium diboride synthesized by borothermal reduction of high-purity ZrO2. Analysis was conducted on ZrB2 ceramics with relative densities greater than 90% using the Nabarro–Herring stress–directed vacancy diffusion model. Temperatures of 1900°C or above and an applied uniaxial pressure of 50 MPa were required to fully densify ZrB2 ceramics by direct current sintering. Ram travel data were collected and used to determine the relative density of the specimens during sintering. Specimens sintered between 1900 and 2100°C achieved relative densities greater than 97%, whereas specimens sintered below 1900°C failed to reach the final stage of sintering. The average grain size ranged from 1.0 to 14.7 μm. The activation energy was calculated from the slope of an Arrhenius plot that used the Kalish equation. The activation energy was 162 ± 34 kJ/mol, which is consistent with the activation energy for dislocation movement in ZrB2. The diffusion coefficients for dislocation motion that controls densification were 5.1 × 10−6 cm2/s at 1900°C and 5.1 × 10−5 cm2/s at 2100°C, as calculated from activation energy and average grain sizes. This study provides evidence that the dominant mechanism for final-stage sintering of ZrB2 ceramics is dislocation motion.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Self-assembly of a triply periodic continuous mesophase with Fddd symmetry in simple one-component liquids

Triply periodic continuous morphologies (networks) arising as a result of the microphase separation in block copolymer melts have so far never been observed self-assembled in systems of particles with spherically symmetric interaction. Here, we report a molecular dynamics simulation where two simple one-component liquids form upon cooling an equilibrium network with the Fddd space group symmetry. This complexity reduction in the liquid network formation in terms of the particle geometry and the number of components evidences the generic nature of this class of phase transition suggesting opportunities for producing these structures in a variety of new systems.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Comparison of fixed charge and polarizable models for predicting the structural, thermodynamic, and transport properties of molten alkali chlorides

Results from extensive molecular dynamics simulations of molten LiCl, NaCl, KCl, and RbCl over a wide range of temperatures are reported. Comparison is made between the “Polarizable Ion Model” (PIM) and the non-polarizable “Rigid Ion Model” (RIM). Densities, self-diffusivities, shear viscosities, ionic conductivities, and thermal conductivities are computed and compared with experimental data. In addition, radial distribution functions are computed from ab initio molecular dynamics simulations and compared with the two sets of classical simulations as well as experimental data. Here, the two classical models perform reasonably well at capturing structural and dynamic properties of the four molten alkali chlorides, both qualitatively and often quantitatively. With the singular exception of liquid density, for which the PIM is more accurate than the RIM, there are few clear trends to suggest that one model is more accurate than the other for the four alkali halide systems studied here.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Role of deep levels and barrier height lowering in current-flow mechanism in 150 μ m thick epitaxial n-type 4H–SiC Schottky barrier radiation detectors

Schottky barrier detectors (SBDs) require larger surface areas than conventional electronics to increase the detection efficiency although such SBDs manifest large diode ideality factors due to inhomogeneous areal distribution of surface barrier height (SBH). Inhomogeneous SBH distributions lead to various current flow mechanisms in SBDs, which need to be identified to optimize detector performance. In this Letter, we identify the current flow mechanism in large area Schottky barrier diodes for radiation detection fabricated on 150 μm thick n-4H–SiC epitaxial layers. The analysis of temperature-dependent forward current–voltage (I–V–T) characteristics of SBDs revealed two linear regions in current–voltage curves up to 450 K, one corresponding to the current flow through a low barrier patch, while the other corresponds to that of average barrier distribution. Applying a SBH distribution model to the reverse I–V–T characteristics, an activation energy of 0.76 eV for the current flow over the Schottky barrier was calculated. Additionally, the activation energy did not directly correspond to any of the defect levels observed from the deep level transient spectroscopy (DLTS). Above 450 K, a Schottky type barrier lowering suggested a current flow through a low barrier patch of ≈ 0.8 eV. The absence of any SBH lowering below 450 K indicated that the current corresponded to a neutrally charged trap level at ≈ 0.6 eV below the conduction band edge, which was consistent with DLTS measurements revealing the presence of an electron trap level Z1/2 at 0.59 eV below the conduction band edge.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Density dependence of the excitation gaps in an undoped Si/SiGe double-quantum-well heterostructure

In this work, we report low-temperature magneto-transport measurements of an undoped Si/SiGe asymmetric double quantum well heterostructure. The density in both layers is tuned independently utilizing top and bottom gates, allowing the investigation of quantum wells at both imbalanced and matched densities. Integer quantum Hall states at total filling factor v T =1 and v T =2 are observed in both density regimes, and the evolution of their excitation gaps is reported as a function of the density. The v T =1 gap evolution departs from the behavior generally observed for valley splitting in the single layer regime. Furthermore, by comparing the v T =2 gap to the single particle tunneling energy, Δ SAS , obtained from Schrödinger–Poisson (SP) simulations, evidence for the onset of spontaneous interlayer coherence is observed for a relative filling fraction imbalance smaller than ~50%.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Two-well injector direct-phonon terahertz quantum cascade lasers

We present an experimental study on a terahertz quantum cascade laser (THz QCL) design that combines both two-well injector and direct-phonon scattering schemes, i.e., a so-called two-well injector direct-phonon design. As a result of the two-well injector direct-phonon scheme presented here, the lasers benefit from both a direct phonon scattering scheme for the lower laser level depopulation and a setback for the doping profile that reduces the overlap of the doped region with active laser states. Additionally, our design also has efficient isolation of the active laser levels from excited and continuum states as indicated by negative differential resistance behavior all the way up to room temperature. This scheme serves as a good platform for improving the temperature performance of THz QCLs as indicated by the encouraging temperature performance results of the device with a relatively high doping level of 7.56 × 10 10 cm −2 and T max ∼ 167 K. With the right optimization of the molecular beam epitaxy growth and interface quality, the injection coupling strength, and the doping density and its profile, the device could potentially reach higher temperatures than the latest records reached for the maximum operating temperature (T max ) of THz QCLs.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Assessment of deep levels with selenium concentration in Cd 1–x Zn x Te 1–y Se y room temperature detector materials

Incorporation of Se into Cd 1–x Zn x Te (CZT) to form the quaternary compound semiconductor Cd 1–x Zn x Te 1–y Se y (CZTS) has proven to be an effective solution for compensating the major flaws associated with CZT, including poor homogeneity and high concentrations of electronically active deep levels that limit the performance of CZT detectors. In order to investigate how deep levels are affected by the Se concentration in CZTS, we performed photoinduced current transient spectroscopy (PICTS) measurements on CZTS crystals grown by the traveling heater method (THM) with 10% atomic Zn and varying atomic percentage of Se from 1.5% to 7.0%. The PICTS scans for up to 4% Se showed an exponential reduction in the capture cross section of deep levels associated with Te secondary phases in conjunction with an increase in a deep level positioned near the mid-gap, which initially increases the electron trapping time before degrading again at higher Se concentrations. The PICTS peaks present in 7% Se were anomalous relative to the other crystals and are expected to originate from transition metal impurities found in the lower-purity CdSe precursor material.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Green-emitting cubic GaN/In 0.16 Ga 0.84 N/GaN quantum well with 32% internal quantum efficiency at room temperature

Structural and optical properties of a green-emitting cubic (i.e., zinc blende) GaN/In 0.16 Ga 0.84 N/GaN single quantum well structure are reported. The active layer is grown on a phase-pure (i.e., 100%) cubic GaN enabled on a 1 × 1 cm 2 U-grooved silicon (100) through aspect ratio phase trapping. Energy dispersive x-ray spectroscopy combined with room temperature cathodoluminescence reveals 522 nm green light emission at room temperature with only 16.0% ± 1.6% of indium content, which is ~30% less than the amount of indium needed in a traditional green-emitting hexagonal (i.e., wurtzite) well. Temperature-dependent behavior of the green emission, such as activation energy, s-shaped peak energy shift, and linewidth, is reported. Cathodoluminescence at 8 and 300 K reveals an internal quantum efficiency of 32.0% ± 0.6%, which is higher than any reported value for cubic wells. Altogether, phase-pure cubic active layers on phase transition cubic GaN are shown to be promising for green and longer wavelength emitters.

42 ENGINEERING↗
DOE OSTI2022

Desorption characteristics of selenium and tellurium thin films

The temperature-dependent desorption behavior of selenium and tellurium is investigated using a heated quartz crystal microbalance. Prior to heating the quartz crystal microbalance, selenium and tellurium films with varying thickness were deposited using thermal effusion cells in a molecular beam epitaxy system for subsequent determination of temperature-dependent mass loss of the deposited films. The desorption rate for tellurium was found to exhibit one sharp peak around 190°C, indicating the loss of the entire film irrespective of film thickness within a temperature window of 20°C, which was completely evaporated at 200°C. Similar experiments for selenium revealed that the thermal desorption took place via a two-stage process with a smaller portion of the material desorbing within an even narrower temperature window of 5°C at a much lower peak temperature of 65°C, while most selenium desorbed within a temperature range of 10°C around 90°C. This two-stage behavior indicated the presence of at least two chemically distinct selenium species or binding states. The direct and quantitative determination of the chalcogen desorption process provides important insights into the kinetics of chalcogenide-based film growth and is in addition of applied benefit to the research community in the area of Se/Te capping and decapping of air sensitive materials as it provides temperature ranges and rates at which full desorption is achieved. Our work furthermore points toward the need for a more detailed understanding of the chemical composition state of atomic and molecular beams supplied from thermal evaporation sources during growth.

36 MATERIALS SCIENCE↗