Search NASA⌕ Search

SEARCH · Search NASA

Results for “As-doping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

12.3% Efficient Lifted-Off and Reconstructed As-Doped CdTe Thin Film Solar Cell

CdTe:As devices grown by MOCVD in the superstrate configuration have been reconfigured to a substrate structure, by employing a cleaving and reconstruction technique. Indium and aluminium doped Zinc oxide (IZO and AZO) layers were used as the transparent front interface without a metal grid. A substrate efficiency of 12.3% was realized with AZO front contact, retaining 80% of the superstrate device efficiency and an impressive approximately 99% of the open-circuit voltage. The IZO-based substrate device on the other hand performed at approximately 69 % retained efficiency. The crucial role of front interfaces is highlighted by the two contacts used here. The results in this work show promise for the development of highly efficient substrate CdTe:As devices.

II-VI semiconductor materials↗
DOE OSTI2022

Effects of Absorber Near-Interface Compensation on Cd(Se,Te) Solar Cell Performance

Arsenic (As) has been shown to be an effective p-type dopant for CdTe, although high performance in As-doped devices remains difficult to achieve. Arsenic is prone to self-compensation in CdTe, as evidenced by the accumulation of dopant atoms in CdTe/Cd(Se,Te) near the interface with MgxZn1-xO (MZO). In this study, we use SCAPS 1D modeling software to investigate the effect of near-interface compensation, helping elucidate loss pathways in present-day As-doped devices and informing future growth directions. We consider three possible results of As accumulation: shallow donors, deep recombination centers, and a thin layer of excess acceptor accumulation. The reduction in near-interface carrier concentration caused by shallow donors is shown to improve open-circuit voltages (VOC), whereas deep levels are detrimental to all performance parameters. The thin charge layer affects capacitance-voltage (CV) measurements by reducing the depletion width while maintaining the same carrier concentration, replicating CV behavior that has been observed in actual devices. These results illustrate the importance of monitoring dopant accumulation within 100 nm of the interface, and suggest that reducing or eliminating the As concentration in this region would be beneficial. An undoped Cd(Se,Te) layer at the interface is suggested as a possible device structure to boost performance.

absorber↗
DOE OSTI2023

Nanometer-scale electrical potential imaging on absorber of CdSeTe solar cells

Here, we report on nm-scale electrical potential imaging throughout As-doped and Cu-doped CdSeTe absorbers using Kelvin probe force microscopy (KPFM). The potential imaging was conducted both laterally and vertically on beveled films using ion milling at small glancing angle. KPFM images electrical potential on the beveled surface and assesses defect charging in the subsurface region within a screening length from the beveled surface. We found that the grain boundaries were positively charged and that there were significant potential fluctuations in both grain boundary versus grain interior and intragrain. We further found that these potential fluctuations decreased significantly toward the front interface. Time of flight secondary ion mass spectrometry imaging shows that Se content increased toward the front interface, consistent with Se passivation of defects. The potential fluctuation was induced by defect charging, and the results elucidate different details of the defect configurations and grain structures of the films with different CdCl 2 treatment temperatures in the As-doped CdSeTe. The defect configurations in the region near the front interface can be a main factor contributing to the device performance difference. Our potential imaging provides insights about the defects throughout the absorber films, and shows that the potential fluctuation has a direct correlation to the V oc deficit.

14 SOLAR ENERGY↗
DOE OSTI2026

CdTe Core: Final Technical Report (FTR)

CdTe is presently the cost-leading thin-film PV technology, directly competing with Si at scale, even when domestically manufactured. While an impressive technology, its efficiency remains much below the detailed balance limit with the largest cause due to its low photovoltage and fill factor. To realize gains, the carrier concentration, minority carrier lifetime, and interface recombination all need to be improved simultaneously over historic levels. Using a new defect chemistry (group V doping instead of copper) has been identified as a viable route using single crystal systems. This project focused on implementing this new defect chemistry in scalable, polycrystalline thin-film photovoltaic CdTe devices with tasks focusing improvements to the front interface, absorber, and rear interface as well as capability development & stakeholder engagement. The goal of the project was to establish a strategy using devices, test structures, detailed characterization, and modeling to quantify the sources of losses in state-of-the-art CdTe photovoltaic devices. Using this strategy and advanced synthesis, losses at the front interface, absorber, and rear interface were worked on in parallel. The final objective was to significantly improve the voltage deficit in CdTe devices to enable improvements in photovoltage and efficiency that can be implemented by industry in the near-term. Over the course of the project, the team developed new characterization techniques, analysis, and modeling which were then applied to state-of-the-art materials generated internally and collaboratively. In particular to enable rapid progress, NREL worked closely with First Solar where NREL grew complete devices as well as ones that interleaved process steps where First Solar had completed different steps such as absorber growth or absorber growth and activation using their baseline methods. Using detailed characterization and analysis including photoemission, photoluminescence, and scanning probe techniques enabled understanding of the loss pathways and area for improvements in our own and First Solar s materials. Ultimately, this contributed to the first series of new world record CdTe efficiencies since 2016, culminating in a 23.1% certified cell that was P-doped along with As-doped cells of similar performance. Internally, NREL improved the statistical variation in baseline As-doped devices and improved average photovoltage by over 100 mV. This was done through an improvement in absorber quality, changed front interface, and improved back contact. In addition to materially improving the fabrication processes at NREL, characterization, analysis, and modeling were developed and disseminated. NREL also played a pivotal role in community building over the course of this project working closely with the Cadmium Telluride Accelerator Consortium. NREL worked in a series of collaborations with academic and industry partners, leveraging knowledge and innovations from this project, as well as helped organize a series of workshops to ensure rapid progress in the field. Working closely with the academic community has led to a dissemination of knowledge; working with First Solar as increased US competitiveness First Solar expanded domestic production to ~10 GW and opened new facilities.

14 SOLAR ENERGY↗
DOE OSTI2025

Bias‐Dependent Quantum Efficiency Reveals Recombination Pathways in Thin Film Solar Cells

Identifying where recombination predominantly occurs—whether at the front interface, back interface, or throughout the bulk—is crucial for optimizing CdSeTe solar cells and many other photovoltaic device architectures. Here, a simple and effective diagnostic is demonstrated: measuring external quantum efficiency (QE) under varying forward biases. The drift–diffusion simulations reveal that each recombination pathway leaves a distinct bias-induced signature in the normalized QE: a progressive drop at long wavelengths for back-limited devices, a short-wavelength decline for front-limited devices, and a relatively uniform decrease across all wavelengths for bulk-limited devices. These predictions are validated with experiments on As-doped and Cu-doped CdSeTe devices, with and without passivation layers or different front buffers. In each case, the observed bias-dependent QE spectral changes align with the simulated recombination map. Because this method uses standard QE instrumentation, it offers a broadly accessible and cost-efficient means to diagnose recombination pathways—extending beyond CdSeTe to other thin-film and emerging solar cell technologies. By pinpointing recombination bottlenecks, researchers and manufacturers can strategically refine doping profiles, passivation schemes, and interface designs to further improve device performance.

CdTe↗
DOE OSTI2022

How arsenic makes amorphous GeSe a robust chalcogenide glass for advanced memory integration

The 3D integration technology in semiconductor fabrication requires a key component, the ovonic threshold switching (OTS) selector, to suppress the current leakage. The As doped amorphous (a-) GeSe glass is a commercialized OTS material in 3D phase-change memory, but the understanding of such a doping mechanism is still inadequate. Here we systematically explore the effect of As doping on the structural, bonding, and dynamics properties of a-GeAsSe using ab initio molecular dynamics simulations. The results reveal that As atoms form strong bonds with both Ge and Se atoms. The distorted octahedral structures and the 5-fold rings linked by atoms are increased. All of these structural features lead to a more disordered configuration. Moreover, as atoms have notably slowed down the atomic mobility, rendering a-GeAsSe a high stability. Overall, our studies offer insightful understanding of As-doping in OTS materials, paving the way for the design and application of advanced selector devices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electro-Optical Characterization of Arsenic-Doped CdSeTe and CdTe Solar Cell Absorbers Doped in-situ During Close Space Sublimation

Most contemporary device models predict that an acceptor concentration of at least 10^16 cm^-3 is required to reach an open circuit voltage of 1 V in polycrystalline CdTe-based solar cells. While copper has traditionally been used as the de facto p-type dopant in polycrystalline cadmium telluride (CdTe) and cadmium selenide telluride (CdSeTe), reaching high acceptor concentrations has proved to be challenging in such devices due to significant dopant compensation. The acceptor concentration in copper-doped CdTe and CdSeTe typically ranges from 10^13 to 10^15 cm^-3 and routinely exhibit low external radiative efficiencies below 0.01%, limiting their implied voltage (i.e., quasi-Fermi level splitting) to approximately 900 mV. As an alternative to copper, this work explores the use of arsenic as a p-type dopant for CdTe and CdSeTe. Using a novel technique in which a thin layer of arsenic-containing material is deposited and used as a reservoir for arsenic to diffuse into a front layer of previously undoped material, this contribution demonstrates that high external radiative efficiencies are achievable, a direct result of combined high acceptor concentrations and long minority-carrier lifetimes in the absorber. This leads to improved implied voltages, and indicates that As-doping represents a promising pathway towards improving the external voltage of CdSeTe/CdTe solar cells.

cadmium telluride↗
DOE OSTI2026

Gold-Induced Chemical Perturbations in CdTe-Based Photovoltaic Cells

Back-contacting p-type CdTe has been identified as one of the major areas of loss in CdTe photovoltaic (PV) power conversion efficiency (PCE). In research settings, Au is a common contact material due to its ease of use and decent performance. This work provides a detailed investigation into using gold for back contacting As-doped, CdCl 2 -treated, polycrystalline CdTe that has been exposed to air after absorber processing, another routine practice. First, X-ray photoemission spectroscopy (XPS) is used to determine the native oxide to be 1.6 nm of CdTeO 3 by using a combination of angle-resolved XPS and the cadmium-modified Auger parameter. During gold metallization of CdTe, oxygen and oxidized tellurium are eliminated from the thin CdTeO 3 native oxide. The fates of the released oxygen and possibly cadmium and tellurium are not known, but these reaction byproducts can enter the absorber bulk or grain boundaries, stay at the interface, or dissolve in the Au. Interfacial hole barriers between CdTe and Au are measured for samples with and without the native oxide present prior to metallization. Results show that the thin CdTeO 3 alleviates the downward band bending by 40 meV from 470 to 430 meV even though it is consumed during interface formation. The implications of these chemical reactions on the device are assessed through photoluminescence (PL) spectroscopy, which shows losses in internal open circuit voltage (iVoc) from 820 to 795 meV, carrier lifetime from 123 to 45 ns, and PL quantum yield from 2.9 × 10 −5 to 1.2 × 10 −5 . Modeling timeresolved PL lifetimes demonstrates the back surface recombination velocity due to metallization reduces minority carrier lifetimes. These results identify the native oxide and show that it plays an important role in mediating downward band bending along with how the back interface reaction can negatively impact device-scale parameters and reduce PV PCE.

14 SOLAR ENERGY↗
DOE OSTI2022

Impact of dopant-induced band tails on optical spectra, charge carrier transport, and dynamics in single-crystal CdTe

Abstract Cadmium telluride (CdTe) semiconductors are used in thin-film photovoltaics, detectors, and other optoelectronic applications. For all technologies, higher efficiency and sensitivity are achieved with reduced charge carrier recombination. In this study, we use state-of-the-art CdTe single crystals and electro-optical measurements to develop a detailed understanding of recombination rate dependence on excitation and temperature in CdTe. We study recombination and carrier dynamics in high-resistivity (undoped) and arsenic (As)-doped CdTe by employing absorption, the Hall effect, time-resolved photoluminescence, and pump-probe in the 80–600 K temperature range. We report extraordinarily long lifetimes (30 µs) at low temperatures in bulk undoped CdTe. Temperature dependencies of carrier density and mobility reveal ionization of the main acceptors and donors as well as dominant scattering by ionized impurities. We also distinguish different recombination defects. In particular, shallow As Te and deep V Cd −As Cd acceptors were responsible for p-type conductivity. AX donors were responsible for electron capture, while nonradiative recombination centers (V Cd −As Te , As 2 precipitates), and native defects (V Cd −Te Cd ) were found to be dominant in p-type and n-type CdTe, respectively. Bimolecular and surface recombination rate temperature dependencies were also revealed, with bimolecular coefficient T −3/2 temperature dependence and 170 meV effective surface barrier, leading to an increase in surface recombination velocity at high temperatures and excitations. The results of this study allowed us to conclude that enhanced crucible rotation growth of As-doped CdTe is advantageous to As activation, leading to longer lifetimes and larger mobilities and open-circuit voltages due to lower absorption and trapping.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Arsenic activation and compensation in single crystal CdTe bilayers

In state-of-the art polycrystalline CdTe photovoltaics, group-V dopant activation is about 2%. Low activation can create electronic defects and lead to recombination and band tail losses. To develop methods to overcome this limitation, dopant activation was systematically investigated using molecular beam epitaxy (MBE) grown single crystal bilayers of As-doped CdTe on undoped CdTe. Results suggest multiple paths for improved As-activation in polycrystalline CdTe-based devices. It was found that the carrier concentration in this MBE material saturated at ∼3 × 1016 cm−3, with high levels (>50%) of As-activation possible. High activation could be achieved with a post-growth activation temperature of ∼450 °C, when the initial doping level was below the saturation level. However, at typical polycrystalline As incorporation levels (>5 × 1016 cm−3), the excess As is inactive or compensating, requiring elevated temperatures (500–600 °C) to achieve high activation. Oxygen in the annealing ambient was detrimental, while the effect of CdCl2 in the ambient is more case-dependent. A 575 °C activation anneal was combined with a 450 °C CdCl2 treatment to better understand the implications for polycrystalline CdTe. Interestingly, on highly doped samples, processes ending with a high temperature step displayed high activation, while those ending at 450 °C significantly reduced the carrier concentration (with or without CdCl2 in the ambient). Low activation can be restored with another high temperature anneal, allowing reproducible toggling between high and low activation based on the final temperature. Photoluminescence revealed the presence of donor–acceptor pairs in the low activation state that appear to be associated with a compensating defect.

14 SOLAR ENERGY↗
DOE OSTI2025

Characterization of dangling bond defects at the crystalline Si/SiO x interface in a polycrystalline Si passivating contact solar cell at room temperature with electrically detected magnetic resonance spectroscopy

Monocrystalline silicon solar cells can achieve photoconversion efficiencies exceeding 26%; however, performance-limiting defects that trap carriers continue to be a challenge. In this work, we have characterized Si solar cells with tunneling SiO x /polycrystalline-Si (poly-Si) passivating contacts (TOPCon) on As-doped Czochralski Si wafers with electrically detected magnetic resonance (EDMR) spectroscopy. We fabricated 2 × 20 mm 2 TOPCon-like mini solar cells with edge passivation alongside larger 4 cm 2 sister cells and obtained similar device characteristics. We performed EDMR spectroscopy at 300 K on two minicells with different degrees of surface passivation based on the recombination parameter, J o , values of 40 and 310 fA/cm2. We optimized the resolution and the signal-to-noise ratio of the EDMR response of the minicells by varying the forward bias voltage and the magnetic field modulation amplitude. We detect two distinct signals with EDMR spectroscopy, an axial-like signal at g = 2.009, 2.0087, and 2.0015, and an isotropic signal at g = 2.0024, which we attribute to Si dangling bonds (P b0 and P b centers) and boron–oxygen related defects, respectively, at or near the c-Si/SiO x interface. The EDMR signals were lower for the cell with a lower value of J o , while the ratio of the two defect populations was very similar. The EDMR signal increases with forward bias but drops to zero at bias voltages >0.5 V, consistent with interface defects within or near the boron-doped emitter depletion region. Our study demonstrates a method to fabricate minicells that can be characterized with EDMR spectroscopy to detect industrially relevant defects in TOPCon cells.

14 SOLAR ENERGY↗
DOE OSTI2025

Nm-scale electrical resistance imaging on CdTe by scanning spreading resistance microscopy

Local resistance imaging can provide information on nm-scale carrier distribution in semiconductor devices. Scanning spreading resistance microscopy (SSRM), an atomic force microscopy-based nm-scale resistance mapping technique, has been developed for carrier delineation in Si microdevices. We report on the development and validation of SSRM on CdTe materials, by testing on molecular beam epitaxy (MBE) grown CdTe films. The probe/CdTe contact resistance was suppressed sufficiently below sample's spreading resistance by pressing the probe into the sample with ∼mN contact force and applying a large sample/probe forward bias voltage (V s ), which was understood by analyzing current-voltage (I-V) involving a serially connected insulating top layer with underlying spreading resistance. The carrier concentration as deduced from the resistance measurement, using a single mobility value, is consistent with Hall measurement with a standard deviation of 14% based on a set of MBE films with carrier concentrations in the range of 10 15 –10 16 /cm 3 . The doping polarity was readily identified by flipping V s polarity, where the resistance with reverse V s is orders of magnitude larger than forward V s . While focusing on the SSRM technique validation, we also show an example on an As-doped Cd(Se,Te) polycrystalline thin film of a high-performance CdTe solar cell, which illustrates the local resistance nonuniformity with up to two orders of magnitude differences, indicating if local mobility is roughly constant, local carrier concentration can have significant nonuniformity.

14 SOLAR ENERGY↗
DOE OSTI2026

Resilience of High-Efficiency CdSeTe:As and CdSeTe:Cu Solar Cells to Proton Irradiation

Power generation in space is currently dominated by expensive III-V multi-junction photovoltaic (PV) devices and cheap crystalline silicon (c-Si) PV devices. Both of these technologies degrade rapidly in proton-radiation-rich space environments, such as the Van Allen belt. The present study of cadmium selenide telluride- (CdSeTe-) based PV devices exposed to 150-to-1500 keV proton irradiation with fluences up to 9 x 1013 cm-2 reveal a more radiation-hard alternative to III-V and c-Si PV technologies. We report on measurement and analysis of current density vs voltage (JV), external quantum efficiency (EQE), external radiative efficiency, and capacitance vs voltage (CV) characteristics. JV characteristics of As-doped CdSeTe devices show 80% remaining power conversion efficiency (PCE) relative to unexposed controls when exposed to 650 keV protons at a fluence of 1012 cm-2. Under these same irradiation conditions, Cu-doped CdSeTe devices demonstrate an even better 95% PCE retention compared with unirradiated control devices. Evidence of radiation-induced absorber p-type doping compensation is observed in the glass-side EQE at 0 V and CV characteristics of most of the irradiated CdSeTe:As devices, but clear compensation is evident only for the most heavily irradiated CdSeTe:Cu devices. Elevated blue-green photocurrent in the film-side 0 V EQE suggests a buried junction in the most heavily irradiated CdSeTe:As devices. Although CdSeTe:Cu devices are the more resilient of the CdSeTe structures, both CdSeTe-based technologies are radiation-hard when compared to c-Si and III-V multi-junction PV.

14 SOLAR ENERGY↗
DOE OSTI2022

Effect of Near-Interface Compensation of CdSeTe Absorber Layers on Solar Cell Performance

Arsenic has been shown to be an effective p-type dopant of CdTe. However, challenges remain in the fabrication of high efficiency CdTe solar cells using As. As-doped CdTe is prone to self-compensation and observed accumulation of dopant atoms in CdTe near the interface with MgZnO (MZO) suggests that this could be occurring. In this study, we use SCAPS 1-D modeling software to investigate the effect of near-interface compensation. We consider three cases: shallow donors, deep recombination centers, and a thin layer of excess positive charge accumulation. All of these cases are shown to have significant effects on the current-voltage characteristics, while the thin charge layer also affects capacitance-voltage measurements.

arsenic↗
DOE OSTI2023

Quantifying carrier dynamics and PL characterization of antimony-doped CdTe and CdSeTe

Our team has achieved ~20% doping activation of CdSeTe with antimony (Sb), whose shallow acceptor level makes it a viable alternative to As.1,2 Arsenic (As)-doped graded CdSeTe photovoltaics have achieved record efficiencies of 22.3%. Remaining challenges include doping activation of only ~2% in polycrystalline films and radiative voltage losses of ~100 mV. Here we use (transient) terahertz and photoluminescence spectroscopy of CdTe:Sb and CdSeTe:Sb to show sufficiently long bulk lifetimes to enable high-efficiency devices. Early results also indicate dominant bandgap emission in CdSeTe:Sb and a lack of potential fluctuations with Sb-doping that have proven detrimental for As-doped films. While more work is needed, these results show significant promise for Sb doping.

14 SOLAR ENERGY↗
DOE OSTI2024

Quantifying carrier dynamics and PL characterization of antimony-doped CdTe and CdSeTe

Our team has achieved ~20% doping activation of CdSeTe with antimony (Sb), whose shallow acceptor level makes it a viable alternative to As.1,2 Arsenic (As)-doped graded CdSeTe photovoltaics have achieved record efficiencies of 22.3%. Remaining challenges include doping activation of only ~2% in polycrystalline films and radiative voltage losses of ~100 mV. Here we use (transient) terahertz and photoluminescence spectroscopy of CdTe:Sb and CdSeTe:Sb to show sufficiently long bulk lifetimes to enable high-efficiency devices. Early results also indicate dominant bandgap emission in CdSeTe:Sb and a lack of potential fluctuations with Sb-doping that have proven detrimental for As-doped films. While more work is needed, these results show significant promise for Sb doping.

14 SOLAR ENERGY↗
DOE OSTI2026

Data for "Gold-Induced Chemical Perturbations in CdTe-Based Photovoltaic Cells"

Back contacting p-type CdTe has been identified as one of the major areas of loss in CdTe photovoltaic (PV) power conversion efficiency (PCE). In research settings, Au is a common contact material due to its ease of use and decent performance. This work provides a detailed investigation into using gold for back contacting As-doped, CdCl2 treated, polycrystalline CdTe that has been exposed to air after absorber processing, another routine practice. First, X-ray photoemission spectroscopy (XPS) is used to determine the native oxide to be 1.6 nm of CdTeO3 using a combination of angle-resolved XPS and the cadmium modified Auger parameter. During gold metallization of CdTe, oxygen and oxidized tellurium are eliminated from the thin CdTeO3 native oxide. The fate of the released oxygen and possibly cadmium and tellurium are not known, but these reaction byproducts can enter the absorber bulk or grain boundaries, stay at the interface, or dissolve in the Au. Interfacial hole barriers between CdTe and Au are measured for samples with and without the native oxide present prior to metallization. Results show that the thin CdTeO3 alleviates the downward band bending by 40 meV from 470 meV to 430 meV even though it is consumed during interface formation. The implications of these chemical reactions on the device are assessed through photoluminescence (PL) spectroscopy which shows losses in internal open circuit voltage (iVoc) from 820 meV to 795 meV, carrier lifetime from 123 ns to 45 ns, and PL quantum yield from 2.9x10-5 to 1.2x10-5. Modeling time-resolved PL lifetimes demonstrates the back surface recombination velocity due to metallization reduces minority carrier lifetimes. These results identify the native oxide and show that it plays an important role in mediating downward band bending along with how the back interface reaction can negatively impact device-scale parameters and reduce PV PCE.

14 SOLAR ENERGY↗