Search NASA⌕ Search

SEARCH · Search NASA

Results for “Autonomous underwater vehicle (AUV)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Intelligent Autonomy for Unmanned Surface and Underwater Vehicles

As the Autonomous Underwater Vehicle (AUV) and Autonomous Surface Vehicle (ASV) platforms mature in endurance and reliability, a natural evolution will occur towards longer, more remote autonomous missions. This evolution will require the development of key capabilities that allow these robotic systems to perform a high level of on-board decisionmaking, which would otherwise be performed by humanoperators. With more decision making capabilities, less a priori knowledge of the area of operations would be required, as these systems would be able to sense and adapt to changing environmental conditions, such as unknown topography, currents, obstructions, bays, harbors, islands, and river channels. Existing vehicle sensors would be dual-use; that is they would be utilized for the primary mission, which may be mapping or hydrographic reconnaissance; as well as for autonomous hazard avoidance, route planning, and bathymetric-based navigation. This paper describes a tightly integrated instantiation of an autonomous agent called CARACaS (Control Architecture for Robotic Agent Command and Sensing) developed at JPL (Jet Propulsion Laboratory) that was designed to address many of the issues for survivable ASV/AUV control and to provide adaptive mission capabilities. The results of some on-water tests with US Navy technology test platforms are also presented.

environmental sensing↗
NASA NTRS2014

Submerged AUV Charging Station

Autonomous Underwater Vehicles (AUVs) are becoming increasingly important for military surveillance and mine detection. Most AUVs are battery powered and have limited lifetimes of a few days to a few weeks. This greatly limits the distance that AUVs can travel underwater. Using a series of submerged AUV charging stations, AUVs could travel a limited distance to the next charging station, recharge its batteries, and continue to the next charging station, thus traveling great distances in a relatively short time, similar to the Old West “Pony Express.” One solution is to use temperature differences at various depths in the ocean to produce electricity, which is then stored in a submerged battery. It is preferred to have the upper buoy submerged a reasonable distance below the surface, so as not to be seen from above and not to be inadvertently destroyed by storms or ocean going vessels. In a previous invention, a phase change material (PCM) is melted (expanded) at warm temperatures, for example, 15 °C, and frozen (contracted) at cooler temperatures, for example, 8 °C. Tubes containing the PCM, which could be paraffin such as pentadecane, would be inserted into a container filled with hydraulic oil. When the PCM is melted (expanded), it pushes the oil out into a container that is pressurized to about 3,000 psi (approx equals 20.7 MPa). When a valve is opened, the high-pressure oil passes through a hydraulic motor, which turns a generator and charges a battery. The low-pressure oil is finally reabsorbed into the PCM canister when the PCM tubes are frozen (contracted). Some of the electricity produced could be used to control an external bladder or a motor to the tether line, such that depth cycling is continued for a very long period of time. Alternatively, after the electricity is generated by the hydraulic motor, the exiting low-pressure oil from the hydraulic motor could be vented directly to an external bladder on the AUV, such that filling of the bladder causes the AUV to rise, and emptying of the bladder allows the AUV to descend. This type of direct buoyancy control is much more energy efficient than using electrical pumps in that the inefficiencies of converting thermal energy to electrical energy to mechanical energy is avoided. AUV charging stations have been developed that use electricity produced by waves on floating buoys and that use electricity from solar photovoltaics on floating buoys. This is the first device that has absolutely no floating or visible parts, and is thus impervious to storms, inadvertent ocean vessel collisions, or enemy sabotage.

Jones, Jack A.↗
DOE OSTI2022

Co-Design of Marine Energy Converters for Autonomous Underwater Vehicle Docking and Recharging - Software and Data

Software and testing data from the OH Hinsdale Wave lab for DOE-funded project on Co-Design of Marine Energy Converters for Autonomous Underwater Vehicle Docking and Recharging. This project will perform foundational research and testing to accelerate the sector-wide development and deployment of marine energy converters to provide Power-At-Sea. Specifically, we seek to overcome known challenges and knowledge gaps for the successful co-design of coupled Wave Energy Converter (WEC)-Autonomous Underwater Vehicles (AUV) systems; systems designed and tested for WEC array system health and environmental monitoring applications. This project brings together an experienced, multi-institution, and multi-disciplinary team to focus on the co-design of marine energy (ME) technologies and AUV docking systems, including multi-body hydrodynamic modeling, active control, autonomy, and hardware interfaces necessary to enable new WEC-focused understanding, and allow for robust and ubiquitous AUV docking and recharging in real-world conditions.

16 TIDAL AND WAVE POWER↗
DOE OSTI2023

Integrated path planning and control through proximal policy optimization for a marine current turbine

This paper presents an integrated path planning and tracking control framework for a marine current turbine (MCT), where the MCT is treated as an energy-harvesting autonomous underwater vehicle (AUV). Considering the ocean (space of action) is continuous, the proposed framework employs two modules to address path planning and path tracking enabled by the proximal policy optimization (PPO) algorithm, which is a policy gradient deep reinforcement learning (RL) method. Further, to enable fully autonomous operation in a stochastic oceanic environment, the proposed path planning seeks a primary objective of maximizing the harvested energy; then, the path tracking module is designed to minimize the tracking error and avoid collisions with static and dynamic obstacles. Using field-collected acoustic Doppler current profiler (ADCP) data, the performance of the proposed framework is evaluated. Comparative studies with baseline algorithms in three different scenarios of path planning, path tracking without an obstacle, and path tracking with collision avoidance verify the effectiveness of our proposed approach.

16 TIDAL AND WAVE POWER↗
DOE OSTI2020

A Scoping Study to Determine the Location-Specific WEC Threshold Size for Wave-Powered AUV Recharging

The aim of this study is to determine the threshold wave energy converter (WEC) type and size to charge a fleet of U.S. Navy autonomous underwater vehicles (AUVs) in various geographic locations of interest. The U.S. Navy deploys AUVs in locations around the world that must be charged manually, decreasing their operational endurance and creating operational limitations. Ocean waves are a potential power source that can be converted into electricity using a WEC and stored using a battery. It would be beneficial to develop a WEC that could autonomously charge AUVs offshore. Numerous locations were analyzed to determine the minimum size of a WEC capable of providing sufficient charging power and offering a strategic advantage. By predicting the WEC efficiency (based on empirical equations) and wave resource (based on available data), electrical power generation across numerous WEC types and locations was compared in MATLAB. The generalized process developed here could be used to determine the required size and type of WECs to charge a fleet of AUVs in different locations around the world.

16 TIDAL AND WAVE POWER↗
NASA NTRS2013

ULTRA: Underwater Localization for Transit and Reconnaissance Autonomy

This software addresses the issue of underwater localization of unmanned vehicles and the inherent drift in their onboard sensors. The software gives a 2 to 3 factor of improvement over the state-of-the-art underwater localization algorithms. The software determines the localization (position, heading) of an AUV (autonomous underwater vehicle) in environments where there is no GPS signal. It accomplishes this using only the commanded position, onboard gyros/accelerometers, and the bathymetry of the bottom provided by an onboard sonar system. The software does not rely on an onboard bathymetry dataset, but instead incrementally determines the position of the AUV while mapping the bottom. In order to enable long-distance underwater navigation by AUVs, a localization method called ULTRA uses registration of the bathymetry data products produced by the onboard forward-looking sonar system for hazard avoidance during a transit to derive the motion and pose of the AUV in order to correct the DR (dead reckoning) estimates. The registration algorithm uses iterative point matching (IPM) combined with surface interpolation of the Iterative Closest Point (ICP) algorithm. This method was used previously at JPL for onboard unmanned ground vehicle localization, and has been optimized for efficient computational and memory use.

Huntsberger, Terrance L.↗
DOE OSTI2022

Integrated Monitoring of Macroalgae Farms Using Acoustics and UUV Sensing

The vision of this project was to develop an integrated system for autonomous underwater vehicle (AUV) monitoring of offshore kelp farms using acoustic, environmental, and optical sensors. This project supports the overall MARINER goals of developing an offshore kelp aquaculture industry to produce low-carbon or carbon-neutral biofuels. The project commenced in the spring of 2018 and used laboratory experiments to test the efficacy of acoustic sensors for monitoring kelp farm lines and growing kelp biomass. Sensors were then integrated onto two AUVs as well as an autonomous surface vehicle in order to establish the optimal type, price point, and vehicle to most efficiently monitor kelp farm structures, kelp biomass, and the surrounding environment. Multiple field deployments of these vehicles and sensors in Massachusetts, New Hampshire, and Maine confirmed that farm lines and kelp could be visualized and that monitoring the spatial patterns of environmental variables was possible. The COVID-19 pandemic severely limited fieldwork activities and laboratory testing, with deployments around kelp farms not occurring again until January 2021. Time spent away from the field focused on data visualization and the development of a low-cost, vessel-based sensor system. Unfortunately, the low-cost system experienced a disk failure during its first deployment and due to multiple resignations from the project team further engineering and development was not possible. Additionally, final results from acoustic sensor testing in 2021 were also not able to be completed due to the resignation of the postdoc leading the analysis. Despite these setbacks, multiple avenues for further development of optical imagery processing from the 360-degree Kelpcam camera and testing of the low-cost sensor system may be possible.

09 BIOMASS FUELS↗
NASA NTRS2001

Ocean-Science Mission Needs: Real-Time AUV Data for Command, Control, and Model Inputs

Predictive models for tides, hydrodynamics, and bio-optical properties affecting the visibility and buoyancy of coastal waters are needed to evaluate the safety of personnel and equipment engaged in maritime operations under potentially hazardous conditions. Predicted currents can be markedly different for two-layer systems affected by terrestrial runoff than for well-mixed conditions because the layering decouples the surface and bottom Ekman layers and rectifies the current response to oscillatory upwelling-and downwelling-favorable winds. Standard ocean models (e.g. Princeton Ocean Model) require initial-and boundary data on the physical and optical properties of the multilayered water column to provide accurate simulations of heat budgets and circulation. Two observational systems are designed to measure vertically structured conditions on the West Florida Shelf (WFS): a tethered buoy network and an autonomous underwater vehicle (AUV) observational system. The AUV system is described with a focus on the observational systems that challenge or limit the communications command and control network for various types of measurement programs. These include vertical oscillatory missions on shelf transects to observe the optical and hydrographic properties of the water column, and bottom-following missions for measuring the bottom albedo. Models of light propagation, absorption, and conversion to heat as well as determination of the buoyancy terms for physical models require these measurements. High data rates associated with video bottom imagery are the most challenging for the real-time, command and control communications system, but they are met through a combination of loss-less and lossy data-compression methods, depending upon the data-rate of the radio links.

Carder, Kendall L.↗
DOE OSTI2023

Domain-aware Control-oriented Neural Models for Autonomous Underwater Vehicles

Conventional physics-based modeling is a time-consuming bottleneck in control design for complex nonlinear systems like autonomous underwater vehicles (AUVs). In contrast, purely data-driven models, require a large number of observations and lack operational guarantees for safety-critical systems. Data-driven models leveraging available partially characterized dynamics have potential to provide reliable systems models in a typical data-limited scenario for high value complex systems, thereby avoiding months of expensive expert modeling time. In this work we explore this middle-ground between expert-modeled and pure data-driven modeling. We present control-oriented parametric models with varying levels of domain-awareness that exploit known system structure and prior physics knowledge to create constrained deep neural dynamical system models. We employ universal differential equations to construct data-driven blackbox and graybox representations of the AUV dynamics. In addition, we explore a hybrid formulation that explicitly models the residual error related to imperfect graybox models. We compare the prediction performance of the learned models for different distributions of initial conditions and control inputs to assess their suitability for control.

Shaw Cortez, Wenceslao E.↗
DOE OSTI2024

TEAMER: MADWEC Techno-Economic Analysis

The objective of this project was for the facility to conduct a techno-economic assessment (TEA) of the Maximal Asymmetric Drag Wave Energy Converter (MADWEC), developed by the University of Massachusetts Dartmouth (UMass Dartmouth). MADWEC is used for powering remote monitoring and Autonomous Underwater Vehicle (AUV) charging systems compared to other existing power supply options. The assessment estimates capital expenditures (CapEx), operational expenditures (OpEx), and power performance for 18 scenarios with the purpose of identifying key cost drivers, comparing total system cost, and comparing the power performance of the power supply options in terms of required installed capacity and estimated theoretical annual energy performance. The 18 assessed scenarios include two end-uses: 1) AUV charging and 2) offshore remote monitoring); three power sources: 1) MADWEC), 2) photovoltaic (PV) solar buoy, 3) and traditional battery swapping); and three locations; 1) nearshore, 2) far-offshore, and 3) high-latitude). In addition, other project goals included developing high level installation, operation, and maintenance plans for each scenario. The techno-economic model, created in Microsoft Excel, estimates CapEx, OpEx, and the power performance of each power supply source. The model has a dynamic format that allows custom inputs to accommodate future changes to the systems being assessed. This is a TEA for the MADWEC project, TEAMER RFTS 7 (request for technical support) program.

16 TIDAL AND WAVE POWER↗
DOE OSTI2020

Powering the Blue Economy - Ocean Observing Use Cases Report

The "Powering the Blue Economy" (PBE) Report identified ocean observing and autonomous underwater vehicle (AUV) recharge as near-term markets with significant potential for marine energy integration when specified qualitative and quantitative assessment criteria were used. The ocean observing market (including AUVs) scored high relative to other markets analyzed in the PBE Report with respect to market size, marine renewable energy (MRE) compatibility with functional requirements, competitive positioning (i.e., MRE versus other power sources), path to market, and alignment to the Department of Energy Water Power Technologies Office (WPTO) and other agencies' objectives. Based on this scoring, Pacific Northwest National Laboratory (PNNL) and the National Renewable Energy Laboratory (NREL) pursued the development of five use cases that represent a spectrum of ocean observation platforms, fixed and mobile, to explore the present and future power needs that might be satisfied by marine energy. The use cases were described and analyzed for this potential by examining current missions and future needs, evaluating the mix of renewable energy sources that might satisfy those needs at sea, and understanding the overall cost drivers that might enable this application.

14 SOLAR ENERGY↗
DOE OSTI2022

Discovering hydrothermalism from Afar: In Situ methane instrumentation and change-point detection for decision-making

Seafloor hydrothermalism plays a critical role in fundamental interactions between geochemical and biological processes in the deep ocean. A significant number of hydrothermal vents are hypothesized to exist, but many of these remain undiscovered due in part to the difficulty of detecting hydrothermalism using standard sensors on rosettes towed in the water column or robotic platforms performing surveys. Here, we use in situ methane sensors to complement standard sensing technology for hydrothermalism discovery and compare sensors on a towed rosette and an autonomous underwater vehicle (AUV) during a 17 km long transect in the Northern Guaymas Basin in the Gulf of California. This transect spatially intersected with a known hydrothermally active venting site. These data show that methane signalled possible hydrothermal-activity 1.5–3 km laterally (100–150 m vertically) from a known vent. Methane as a signal for hydrothermalism performed similarly to standard turbidity sensors (plume detection 2.2–3.3 km from reference source), and more sensitively and clearly than temperature, salinity, and oxygen instruments which readily respond to physical mixing in background seawater. We additionally introduce change-point detection algorithms—streaming cross-correlation and regime identification—as a means of real-time hydrothermalism discovery and discuss related data supervision technologies that could be used in planning, executing, and monitoring explorative surveys for hydrothermalism.

58 GEOSCIENCES↗
DOE OSTI2023

Editorial: Deep-sea observation equipment and exploration technology

The increasing interest in deep-sea exploration is a crucial catalyst for driving advancements in deep-sea observation technology research. Numerous sophisticated sensors have been developed to facilitate comprehensive studies in deep-sea physics, chemistry, and geology. For example, cutting-edge small and compact seabed samplers are now employed on various platforms, such as Autonomous Underwater Vehicles (AUVs), Remotely Operated Vehicles (ROVs), and Human-Operated Vehicles (HOVs), enabling observation of the hadal zone. Additionally, Micro-electromechanical systems (MEMS) sensors are routinely utilized for ocean wave observation. This Research Topic aims to foster new insights into ocean exploration and observation technology, including ocean sensor technology, ocean observation platforms, and ocean observation reliability technology.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Robotic Planning under Uncertainty in Spatiotemporal Environments in Expeditionary Science

In the expeditionary sciences, spatiotemporally varying environments -- hydrothermal plumes, algal blooms, lava flows, or animal migrations -- are ubiquitous. Mobile robots are uniquely well-suited to study these dynamic, mesoscale natural environments. We formalize expeditionary science as a sequential decision-making problem, modeled using the language of partially-observable Markov decision processes (POMDPs). Solving the expeditionary science POMDP under real-world constraints requires efficient probabilistic modeling and decision-making in problems with complex dynamics and observational models. Previous work in informative path planning, adaptive sampling, and experimental design have shown compelling results, largely in static environments, using data-driven models and information-based rewards. However, these methodologies do not trivially extend to expeditionary science in spatiotemporal environments: they generally do not make use of scientific knowledge such as equations of state dynamics, they focus on information gathering as opposed to scientific task execution, and they make use of decision-making approaches that scale poorly to large, continuous problems with long planning horizons and real-time operational constraints. In this work, we discuss these and other challenges related to probabilistic modeling and decision-making in expeditionary science, and present some of our preliminary work that addresses these gaps. We ground our results in a real expeditionary science deployment of an autonomous underwater vehicle (AUV) in the deep ocean for hydrothermal vent discovery and characterization. Our concluding thoughts highlight remaining work to be done, and the challenges that merit consideration by the reinforcement learning and decision-making community.

Preston, Victoria↗
DOE OSTI2024

Results from a multi-laboratory ocean metaproteomic intercomparison: effects of LC-MS acquisition and data analysis procedures

Metaproteomics is an increasingly popular methodology that provides information regarding the metabolic functions of specific microbial taxa and has potential for contributing to ocean ecology and biogeochemical studies. A blinded multi-laboratory intercomparison was conducted to assess comparability and reproducibility of taxonomic and functional results and their sensitivity to methodological variables. Euphotic zone samples from the Bermuda Atlantic Time-series Study (BATS) in the North Atlantic Ocean collected by in situ pumps and the autonomous underwater vehicle (AUV) Clio were distributed with a paired metagenome, and one-dimensional (1D) liquid chromatographic data-dependent acquisition mass spectrometry analysis was stipulated. Analysis of mass spectra from seven laboratories through a common bioinformatic pipeline identified a shared set of 1056 proteins from 1395 shared peptide constituents. Quantitative analyses showed good reproducibility: pairwise regressions of spectral counts between laboratories yielded R 2 values averaged 0.62±0.11, and a Sørensen similarity analysis of the top 1000 proteins revealed 70 %–80 % similarity between laboratory groups. Taxonomic and functional assignments showed good coherence between technical replicates and different laboratories. A bioinformatic intercomparison study, involving 10 laboratories using eight software packages, successfully identified thousands of peptides within the complex metaproteomic datasets, demonstrating the utility of these software tools for ocean metaproteomic research. Lessons learned and potential improvements in methods were described. Future efforts could examine reproducibility in deeper metaproteomes, examine accuracy in targeted absolute quantitation analyses, and develop standards for data output formats to improve data interoperability. Together, these results demonstrate the reproducibility of metaproteomic analyses and their suitability for microbial oceanography research, including integration into global-scale ocean surveys and ocean biogeochemical models.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1987

SOLON: An autonomous vehicle mission planner

The State-Operator Logic Machine (SOLON) Planner provides an architecture for effective real-time planning and replanning for an autonomous vehicle. The highlights of the system, which distinguish it from other AI-based planners that have been designed previously, are its hybrid application of state-driven control architecture and the use of both schematic representations and logic programming for the management of its knowledge base. SOLON is designed to provide multiple levels of planning for a single autonomous vehicle which is supplied with a skeletal, partially-specified mission plan at the outset of the vehicle's operations. This mission plan consists of a set of objectives, each of which will be decomposable by the planner into tasks. These tasks are themselves comparatively complex sets of actions which are executable by a conventional real-time control system which does not perform planning but which is capable of making adjustments or modifications to the provided tasks according to constraints and tolerances provided by the Planner. The current implementation of the SOLON is in the form of a real-time simulation of the Planner module of an Intelligent Vehicle Controller (IVC) on-board an autonomous underwater vehicle (AUV). The simulation is embedded within a larger simulator environment known as ICDS (Intelligent Controller Development System) operating on a Symbolics 3645/75 computer.

Dudziak, M. J.↗
NASA NTRS1991

A mission executor for an autonomous underwater vehicle

The Naval Postgraduate School has been conducting research into the design and testing of an Autonomous Underwater Vehicle (AUV). One facet of this research is to incrementally design a software architecture and implement it in an advanced testbed, the AUV II. As part of the high level architecture, a Mission Executor is being constructed using CLIPS (C Language Integrated Production System) version 5.0. The Mission Executor is an expert system designed to oversee progress from the AUV launch point to a goal area and back to the origin. It is expected that the executor will make informed decisions about the mission, taking into account the navigational path, the vehicle subsystem health, and the sea environment, as well as the specific mission profile which is downloaded from an offboard mission planner. Heuristics for maneuvering, avoidance of uncharted obstacles, waypoint navigation, and reaction to emergencies (essentially the expert knowledge of a submarine captain) are required. Many of the vehicle subsystems are modeled as objects using the CLIPS Object Oriented Language (COOL) embedded in CLIPS 5.0. Also, truth maintenance is applied to the knowledge base to keep configurations updated.

Lee, Yuh-Jeng↗
NASA NTRS1992

Automated in situ observations of upper ocean biogeochemistry, bio-optics, and physics and their potential use for global studies

The processes controlling the flux of carbon in the upper ocean have dynamic ranges in space and time of at least nine orders of magnitude. These processes depend on a broad suite of inter-related biogeochemical, bio-optical, and physical variables. These variables should be sampled on scales matching the relevant phenomena. Traditional ship-based sampling, while critical for detailed and more comprehensive observations, can span only limited portions of these ranges because of logistical and financial constraints. Further, remote observations from satellite platforms enable broad horizontal coverage which is restricted to the upper few meters of the ocean. For these main reasons, automated subsurface measurement systems are important for the fulfillment of research goals related to the regional and global estimation and modeling of time varying biogeochemical fluxes. Within the past few years, new sensors and systems capable of autonomously measuring several of the critical variables have been developed. The platforms for deploying these systems now include moorings and drifters and it is likely that autonomous underwater vehicles (AUV's) will become available for use in the future. Each of these platforms satisfies particular sampling needs and can be used to complement both shipboard and satellite observations. In the present review, (1) sampling considerations will be summarized, (2) examples of data obtained from some of the existing automated in situ sampling systems will be highlighted, (3) future sensors and systems will be discussed, (4) data management issues for present and future automated systems will be considered, and (5) the status of near real-time data telemetry will be outlined. Finally, we wish to make it clear at the outset that the perspectives presented here are those of the authors and are not intended to represent those of the United States JGOFS program, the International JGOFS program, NOAA's C&GC program, or other global ocean programs.

Dickey, Tommy D.↗