NASA 8- by 6-Foot Supersonic Wind Tunnel Boundary Layer Ingestion (BLI) BLI Inlet Distortion-Tolerant Fan Wind Tunnel Experiment
The Boundary Layer Ingestion poster is an overview of the technology.
BLI Poster↗
SEARCH · Search NASA
Results for “BLI”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Blended Wing Body (BWB) Boundary Layer Ingestion (BLI) Inlet Configuration and System Studies
A study was conducted to determine the potential reduction in fuel burned for BLI (boundary layer ingestion) inlets on a BWB (blended wing body) airplane employing AFC (active flow control). The BWB is a revolutionary type airplane configuration with engines on the aft upper surface where thick boundary layer offers the greatest opportunity for ram drag reduction. AFC is an emerging technology for boundary layer control. Several BLI inlet configurations were analyzed in the NASA-developed RANS Overflow CFD code. The study determined that, while large reductions in ram drag result from BLI, lower inlet pressure recovery produces engine performance penalties that largely offset this ram drag reduction. AFC could, however, enable a short BLI inlet that allows surface mounting of the engine which, when coupled with a short diffuser, would significantly reduce drag and weight for a potential 10% reduction in fuel burned. Continuing studies are therefore recommended to achieve this reduction in fuel burned considering the use of more modest amounts of BLI coupled with both AFC and PFC (Passive Flow Control) to produce a fail-operational system.
Kawai, Ronald T.↗
Numerical Simulation of Boundary Layer Ingesting (BLI) Inlet-Fan Interaction
Future civil transport designs may incorporate engine inlets integrated into the body of the aircraft to take advantage of efficiency increases due to weight and drag reduction. Additional increases in engine efficiency are predicted if the inlet ingests the lower momentum boundary layer flow. Previous studies have shown, however, that efficiency benefits of Boundary Layer Ingesting (BLI) ingestion are very sensitive to the magnitude of fan and duct losses, and blade structural response to the non-uniform flow field that results from a BLI inlet has not been studied in-depth. This paper presents an effort to extend the modeling capabilities of an existing rotating turbomachinery unsteady analysis code to include the ability to solve the external and internal flow fields of a BLI inlet. The TURBO code has been a successful tool in evaluating fan response to flow distortions for traditional engine/inlet integrations, such as the development of rotating stall and inlet distortion through compressor stages. This paper describes the first phase of an effort to extend the TURBO model to calculate the external and inlet flowfield upstream of fan so that accurate pressure distortions that result from BLI configurations can be computed and used to analyze fan aerodynamics and structural response. To validate the TURBO program modifications for the BLI flowfield, experimental test data obtained by NASA for a flushmounted S-duct with large amounts of boundary layer ingestion was modeled. Results for the flow upstream and in the inlet are presented and compared to experimental data for several high Reynolds number flows to validate the modifications to the solver. Quantitative data is presented that indicates good predictive capability of the model in the upstream flow. A representative fan is attached to the inlet and results are presented for the coupled inlet/fan model. The impact on the total pressure distortion at the AIP after the fan is attached is examined.
Inlet Fan Interactions↗
Aeropropulsive Assessment of a BLI Tail-Cone Thruster Propulsion System for the NASA Common Research Model and a Transonic Truss-Braced Wing Configuration
This paper presents an investigation into the potential benefits of a boundary layer ingestion(BLI) aft fuselage propulsion system, or tail-cone thruster (TCT), when applied to two transport category aircraft: a conventional tube-and-wing configuration based on the NASA Common Research Model (CRM) and a transonic truss-braced wing (TTBW) configuration. Through the ingestion of low-momentum flow developed over the airframe of an aircraft, the TCT propulsion system technology can reduce overall power consumption and hence fuel burn and emissions. However, an accurate assessment of this potential requires the application of high-fidelity analysis tools that can capture the relevant propulsion-airframe integration effects, at least to first order. Toward this end, the present study employs aeropropulsive analysis tools based on the Reynolds-averaged Navier-Stokes equations to estimate the power savings coefficient, measured relative to equivalent non-BLI configurations of a given airframe. Results indicate shaft power savings of 4.1% and 5.9% can be obtained for the boundary-layer ingesting TCT configuration of the CRM and TTBW, respectively. The present study also examines the coupling between airframe aerodynamics and the inlet flow distortion experienced by the TCT of a given aircraft configuration through airframe component sensitivity studies.
AATT↗
Computational Fluid Dynamics (CFD) Design of a Blended Wing Body (BWB) with Boundary Layer Ingestion (BLI) Nacelles
A study is being conducted to improve the propulsion/airframe integration for the Blended Wing-Body (BWB) configuration with boundary layer ingestion nacelles. TWO unstructured grid flow solvers, USM3D and FUN3D, have been coupled with different design methods and are being used to redesign the aft wing region and the nacelles to reduce drag and flow separation. An initial study comparing analyses from these two flow solvers against data from a wind tunnel test as well as predictions from the OVERFLOW structured grid code for a BWB without nacelles has been completed. Results indicate that the unstructured grid codes are sufficiently accurate for use in design. Results from the BWB design study will be presented.
Morehouse, Melissa B.↗
Experimental Evaluation of BLI Propulsion: The Boundary Layer Ingesting Inlet/Distortion-Tolerant Fan Solution
NASA has successfully developed a new testbed configuration for experimentally evaluating embedded boundary layer ingesting aircraft propulsors in its 8'x6' Supersonic Wind Tunnel. This testbed meets the challenges of providing the necessary freestream flow Mach conditions and desired range and distribution of boundary layer thickness for embedded aircraft propulsion systems. The testbed consists of a 48ft long raised wind tunnel floor aircraft surface simulator and a boundary layer regulation system to produce propulsion-local aircraft aerodynamic flow fields. This durable special test equipment is designed to be installed in the wind tunnel's transonic test section and is capable of evaluating a wide range of subcritical and supercritical airframe-propulsion integration configurations for subsonic cruise aircraft. The wind tunnel and testbed are well suited for meeting the test requirements of these propulsors in the most cost efficient way and has been aerodynamically calibrated and proven through tests of a first-of-its-kind boundary layer ingesting propulsor.
Arend, David J.↗
Vehicle-Level System Impact of Boundary Layer Ingestion for the NASA D8 Concept Aircraft
The purpose of this study was to evaluate the vehicle-level impact of a boundary layer ingestion (BLI) propulsion system on a commercial transport aircraft concept. The NASA D8 (ND8) aircraft was chosen as the BLI concept aircraft to be studied. A power balance methodology developed by the Massachusetts Institute of Technology was adapted for use with the existing NASA sizing and performance tools to model the fuel consumption impact of BLI on the ND8. A key assumption for the BLI impact assessment was a 3.5% efficiency penalty associated with designing a fan for and operating in the distorted flow caused by BLI. The ND8 was compared to several other ND8-like aircraft that did not utilize BLI in order to determine the fuel consumption benefit attributable to BLI. Analytically “turning off” BLI on the ND8 without accounting for the physical requirements of redirecting the boundary layer or resizing the aircraft to meet the performance constraints resulted in a 2.8% increase in block fuel consumption to fly the design mission. When this non-physical aircraft was resized to meet the performance constraints, the block fuel consumption was 4.0% greater than the baseline ND8. The ND8 was also compared to an ND8-like aircraft with conventionally podded engines under the wing. This configuration had a 5.6% increase in block fuel consumption compared to the baseline ND8. This result is more reflective of the real world impact if BLI is not an available technology for the ND8 design. The BLI benefit results presented for this study should not be applied to other aircraft that have a propulsion-airframe integration design or BLI implementation different from the ND8.
Marien, Ty V.↗
BENEFIT AND CRITICAL FACTORS FOR THE PERFORMANCE OF THE BOUNDARY LAYER INGESTING PROPULSION
The benefit of the boundary layer ingestion(BLI)is described in the perspective of the propulsion and engine development. A power saving map of the BLI engines is derived based on the correlation of the wake velocity ratio of the ingested boundary layer profile and the propulsive efficiency. The ratio of the mass flow rate between BLI and non-BLI propulsors is introduced to quantify the power saving of the BLI engine relative to a clean inlet flow engine which generates same amount of thrust. The wake recovery factor from the jet flow out of the BLI engine is employed to find an adequate sizing of the BLI engine for the given design requirement. The effects of the fan pressure ratio on the power saving are also investigated to explore the feasible range of the BLI engine design. The derived correlation is validated with CFD analyses. A numerical experiment is carried out by varying the wake velocity ratio through different BLI engines sized with respect to an influencing body. Consequently, the propulsor efficiency is quantified and presented by the saving in the actual shaft power. The efficiency penalty, pressure ratio of the BLI fan stage are correlated with the power saving and the correlation is validated through BLI2DTF and R4 fan stage CFD analyses based on rig test data.
B J Lee↗
Computational Investigation of a Boundary-Layer Ingestion Propulsion System for the Common Research Model
This thesis will examine potential propulsive and aerodynamic benefits of integrating a boundary-layer ingestion (BLI) propulsion system with a typical commercial aircraft using the Common Research Model geometry and the NASA Tetrahedral Unstructured Software System (TetrUSS). The Numerical Propulsion System Simulation (NPSS) environment will be used to generate engine conditions for CFD analysis. Improvements to the BLI geometry will be made using the Constrained Direct Iterative Surface Curvature (CDISC) design method. Previous studies have shown reductions of up to 25% in terms of propulsive power required for cruise for other axisymmetric geometries using the BLI concept. An analysis of engine power requirements, drag, and lift coefficients using the baseline and BLI geometries coupled with the NPSS model are shown. Potential benefits of the BLI system relating to cruise propulsive power are quantified using a power balance method and a comparison to the baseline case is made. Iterations of the BLI geometric design are shown and any improvements between subsequent BLI designs presented. Simulations are conducted for a cruise flight condition of Mach 0.85 at an altitude of 38,500 feet and an angle of attack of 2deg for all geometries. A comparison between available wind tunnel data, previous computational results, and the original CRM model is presented for model verification purposes along with full results for BLI power savings. Results indicate a 14.3% reduction in engine power requirements at cruise for the BLI configuration over the baseline geometry. Minor shaping of the aft portion of the fuselage using CDISC has been shown to increase the benefit from boundary-layer ingestion further, resulting in a 15.6% reduction in power requirements for cruise as well as a drag reduction of eighteen counts over the baseline geometry.
Blumenthal, Brennan↗
Computational Investigation of a Boundary-Layer Ingesting Propulsion System for the Common Research Model
The present paper examines potential propulsive and aerodynamic benefits of integrating a Boundary-Layer Ingestion (BLI) propulsion system into a typical commercial aircraft using the Common Research Model (CRM) geometry and the NASA Tetrahedral Unstructured Software System (TetrUSS). The Numerical Propulsion System Simulation (NPSS) environment is used to generate engine conditions for CFD analysis. Improvements to the BLI geometry are made using the Constrained Direct Iterative Surface Curvature (CDISC) design method. Previous studies have shown reductions of up to 25% in terms of propulsive power required for cruise for other axisymmetric geometries using the BLI concept. An analysis of engine power requirements, drag, and lift coefficients using the baseline and BLI geometries coupled with the NPSS model are shown. Potential benefits of the BLI system relating to cruise propulsive power are quantified using a power balance method, and a comparison to the baseline case is made. Iterations of the BLI geometric design are shown and any improvements between subsequent BLI designs presented. Simulations are conducted for a cruise flight condition of Mach 0.85 at an altitude of 38,500 feet and an angle of attack of 2 deg for all geometries. A comparison between available wind tunnel data, previous computational results, and the original CRM model is presented for model verification purposes along with full results for BLI power savings. Results indicate a 14.4% reduction in engine power requirements at cruise for the BLI configuration over the baseline geometry. Minor shaping of the aft portion of the fuselage using CDISC has been shown to increase the benefit from Boundary-Layer Ingestion further, resulting in a 15.6% reduction in power requirements for cruise as well as a drag reduction of eighteen counts over the baseline geometry.
Blumenthal, Brennan T.↗
Numerical Modeling of Flow Control in a Boundary-Layer-Ingesting Offset Inlet Diffuser at Transonic Mach Numbers
This paper will investigate the validation of the NASA developed, Reynolds-averaged Navier-Stokes (RANS) flow solver, OVERFLOW, for a boundary-layer-ingesting (BLI) offset (S-shaped) inlet in transonic flow with passive and active flow control devices as well as a baseline case. Numerical simulations are compared to wind tunnel results of a BLI inlet experiment conducted at the NASA Langley 0.3-Meter Transonic Cryogenic Tunnel. Comparisons of inlet flow distortion, pressure recovery, and inlet wall pressures are performed. The numerical simulations are compared to the BLI inlet data at a free-stream Mach number of 0.85 and a Reynolds number of approximately 2 million based on the fanface diameter. The numerical simulations with and without tunnel walls are performed, quantifying tunnel wall effects on the BLI inlet flow. A comparison is made between the numerical simulations and the BLI inlet experiment for the baseline and VG vane cases at various inlet mass flow rates. A comparison is also made to a BLI inlet jet configuration for varying actuator mass flow rates at a fixed inlet mass flow rate. Overall, the numerical simulations were able to predict the baseline circumferential flow distortion, DPCP avg, very well within the designed operating range of the BLI inlet. A comparison of the average total pressure recovery showed that the simulations were able to predict the trends but had a negative 0.01 offset when compared to the experimental levels. Numerical simulations of the baseline inlet flow also showed good agreement with the experimental inlet centerline surface pressures. The vane case showed that the CFD predicted the correct trends in the circumferential distortion levels for varying inlet mass flow but had a distortion level that was nearly twice as large as the experiment. Comparison to circumferential distortion measurements for a 15 deg clocked 40 probe rake indicated that the circumferential distortion levels are very sensitive to the symmetry of the flow and that a misalignment of the vanes in the experiment could have resulted in this difference. The numerical simulations of the BLI inlet with jets showed good agreement with the circumferential inlet distortion levels for a range of jet actuator mass flow ratios at a fixed inlet mass flow rate. The CFD simulations for the jet case also predicted an average total pressure recovery offset that was 0.01 lower than the experiment as was seen in the baseline. Comparisons of the flow features for the jet cases revealed that the CFD predicted a much larger vortex at the engine fan-face when compare to the experiment.
Allan, Brian G.↗
Benefit and Critical Factors for the Performance of the Boundary Layer Ingesting Propulsion
The benefit of the boundary layer ingestion (BLI) is described in the perspective of the propulsion and engine development. A power saving map of the BLI engines is derived based on the correlation of the shape factor of the ingested boundary layer and the propulsive efficiency. The ratio of the mass flow rate between BLI and non-BLI propulsors is introduced to quantify the power saving of the BLI engine relative to a corresponding clean inlet flow engine that generates the same amount of net thrust. The wake recovery factor from the jet flow is applied to find the optimum sizing of the engine for the given design requirement. The effects of the fan pressure ratio of the propulsor toward the power saving are also investigated to seek out the feasible range of the BLI propulsor design. The derived correlation is validated with CFD analyses. Simulation models using variously sized engines relative to an influencing body are developed so that a numerical experiment is carried out with the various shape factors. The effect of the propulsion airframe integration toward the aerodynamic forces on the fuselage and nacelle is investigated via parametric study of the engine sizing and fan pressure ratio for the wake ingestion models. The propulsor efficiency is quantified toward the saving in the actual shaft power and correlated with the efficiency penalty of the BLI propulsor. The correlation is also validated via comparison of the turbo-machinery CFD results for BLI2DTF and conventional transonic fan stages.
Boundary Layer Ingestion↗
Active Flow Control on a Boundary-Layer-Ingesting Inlet
Boundary layer ingestion (BLI) is explored as means to improve overall system performance for Blended Wing Body configuration. The benefits of BLI for vehicle system performance benefit are assessed with a process derived from first principles suitable for highly-integrated propulsion systems. This performance evaluation process provides framework within which to assess the benefits of an integrated BLI inlet and lays the groundwork for higher-fidelity systems studies. The results of the system study show that BLI provides a significant improvement in vehicle performance if the inlet distortion can be controlled, thus encouraging the pursuit of active flow control (AFC) as a BLI enabling technology. The effectiveness of active flow control in reducing engine inlet distortion was assessed using a 6% scale model of a 30% BLI offset, diffusing inlet. The experiment was conducted in the NASA Langley Basic Aerodynamics Research Tunnel with a model inlet designed specifically for this type of testing. High mass flow pulsing actuators provided the active flow control. Measurements were made of the onset boundary layer, the duct surface static pressures, and the mass flow through the duct and the actuators. The distortion was determined by 120 total pressure measurements located at the aerodynamic interface plane. The test matrix was limited to a maximum freestream Mach number of 0.15 with scaled mass flows through the inlet for that condition. The data show that the pulsed actuation can reduce distortion from 29% to 4.6% as measured by the circumferential distortion descriptor DC60 using less than 1% of inlet mass flow. Closed loop control of the actuation was also demonstrated using a sidewall surface static pressure as the response sensor.
Gorton, Susan Althoff↗
Numerical Modeling of Flow Control in a Boundary-Layer-Ingesting Offset Inlet Diffuser at Transonic Mach Numbers
This paper will investigate the validation of a NASA developed, Reynolds-averaged Navier-Stokes (RANS) flow solver, OVERFLOW, for a boundary-layer-ingesting (BLI) offset (S-shaped) inlet in transonic flow with passive and active flow control devices as well as the baseline case. Numerical simulations are compared to wind tunnel results of a BLI inlet conducted at the NASA Langley 0.3-Meter Transonic Cryogenic Tunnel. Comparisons of inlet flow distortion, pressure recovery, and inlet wall pressures are performed. The numerical simulations are compared to the BLI inlet data at a freestream Mach number of 0.85 and a Reynolds number of approximately 2 million based on the length of the fan-face diameter. The numerical simulations with and without wind tunnel walls are performed, quantifying effects of the tunnel walls on the BLI inlet flow measurements. The wind tunnel test evaluated several different combinations of jet locations and mass flow rates as well as a vortex generator (VG) vane case. The numerical simulations will be performed on a single jet configuration for varying actuator mass flow rates at a fix inlet mass flow condition. Validation of the numerical simulations for the VG vane case will also be performed for varying inlet mass flow rates. Overall, the numerical simulations were able to predict the baseline circumferential flow distortion, DPCPavg, very well for comparisons made within the designed operating range of the BLI inlet. However the CFD simulations did predict a total pressure recovery that was 0.01 lower than the experiment. Numerical simulations of the baseline inlet flow also showed good agreement with the experimental inlet centerline surface pressures. The vane case showed that the CFD predicted the correct trends in the circumferential distortion for varying inlet mass flow but had a distortion level that was nearly twice as large as the experiment. Comparison to circumferential distortion measurements for a 15 deg clocked 40 probe rake indicated that the circumferential distortion levels are very sensitive to the symmetry of the flow and that a miss alignment of the vanes in the experiment could have resulted in this difference. The numerical simulations of the BLI inlet with jets showed good agreement with the circumferential inlet distortion levels for a range of jet actuator mass flow ratios at a fixed inlet mass flow rate. The CFD simulations for the jet case also predicted an average total pressure recovery that was 0.01 lower than the experiment as was seen in the baseline. Comparison of the flow features the jet case revealed that the CFD predicted a much larger vortex at the engine fan-face when compare to the experiment.
Allan Brian G.↗
Performance Analysis of Optimized STARC-ABL Designs Across the Entire Mission Profile
Boundary layer ingestion (BLI) offers the potential for significant fuel burn reduction by exploiting strong aeropropulsive interactions. NASA’s STARC–ABL concept uses an electri- cally powered BLI tail cone thruster on what is otherwise a traditional airframe. Despite the traditional airframe of this configuration, aeropropulsive integration is critical to the perfor- mance of the BLI propulsor. Furthermore, due to being electrically powered, the fan pressure ratio and efficiency of the BLI tail cone thruster vary widely across the flight envelope, and this variation in fan performance must be accounted for with the aeropropulsive integration of the BLI system. Thus, accurate performance prediction for this novel propulsion configu- ration requires the use of a coupled aeropropulsive model across the flight envelope. In this work, we analyze the off-design performance of 18 optimized designs using an aeropropulsive model that is built with the OpenMDAO framework to couple 3-D RANS CFD simulations to 1-D thermodynamic cycle analyses. The designs are created via high-fidelity aeropropulsive design optimizations that span a range of fan pressure ratio and thrust values at the cruise conditions for the STARC-ABL concept, which was chosen as the aerodynamic design point for the propulsor. Performance analyses we present herein are then performed at a range of off-design flight conditions that span the flight envelope, including low-speed and low-altitude flight conditions. This study provides the first set of high-fidelity data for the STARC–ABL configuration at off-design conditions, and the results quantify the power savings through BLI compared to a traditional propulsion system across the entire mission profile.
optimization↗
Optimal Design of Passive Flow Control for a Boundary-Layer-Ingesting Offset Inlet Using Design-of-Experiments
This research will investigate the use of Design-of-Experiments (DOE) in the development of an optimal passive flow control vane design for a boundary-layer-ingesting (BLI) offset inlet in transonic flow. This inlet flow control is designed to minimize the engine fan-face distortion levels and first five Fourier harmonic half amplitudes while maximizing the inlet pressure recovery. Numerical simulations of the BLI inlet are computed using the Reynolds-averaged Navier-Stokes (RANS) flow solver, OVERFLOW, developed at NASA. These simulations are used to generate the numerical experiments for the DOE response surface model. In this investigation, two DOE optimizations were performed using a D-Optimal Response Surface model. The first DOE optimization was performed using four design factors which were vane height and angles-of-attack for two groups of vanes. One group of vanes was placed at the bottom of the inlet and a second group symmetrically on the sides. The DOE design was performed for a BLI inlet with a free-stream Mach number of 0.85 and a Reynolds number of 2 million, based on the length of the fan-face diameter, matching an experimental wind tunnel BLI inlet test. The first DOE optimization required a fifth order model having 173 numerical simulation experiments and was able to reduce the DC60 baseline distortion from 64% down to 4.4%, while holding the pressure recovery constant. A second DOE optimization was performed holding the vanes heights at a constant value from the first DOE optimization with the two vane angles-of-attack as design factors. This DOE only required a second order model fit with 15 numerical simulation experiments and reduced DC60 to 3.5% with small decreases in the fourth and fifth harmonic amplitudes. The second optimal vane design was tested at the NASA Langley 0.3- Meter Transonic Cryogenic Tunnel in a BLI inlet experiment. The experimental results showed a 80% reduction of DPCP(sub avg), the circumferential distortion level at the engine fan-face.
Allan, Brian G.↗
Optimal Design of Passive Flow Control for a Boundary-Layer-Ingesting Offset Inlet Using Design-of-Experiments
This research will investigate the use of Design-of-Experiments (DOE) in the development of an optimal passive flow control vane design for a boundary-layer-ingesting (BLI) offset inlet in transonic flow. This inlet flow control is designed to minimize the engine fan face distortion levels and first five Fourier harmonic half amplitudes while maximizing the inlet pressure recovery. Numerical simulations of the BLI inlet are computed using the Reynolds-averaged Navier-Stokes (RANS) flow solver, OVERFLOW, developed at NASA. These simulations are used to generate the numerical experiments for the DOE response surface model. In this investigation, two DOE optimizations were performed using a D-Optimal Response Surface model. The first DOE optimization was performed using four design factors which were vane height and angles-of-attack for two groups of vanes. One group of vanes was placed at the bottom of the inlet and a second group symmetrically on the sides. The DOE design was performed for a BLI inlet with a free-stream Mach number of 0.85 and a Reynolds number of 2 million, based on the length of the fan face diameter, matching an experimental wind tunnel BLI inlet test. The first DOE optimization required a fifth order model having 173 numerical simulation experiments and was able to reduce the DC60 baseline distortion from 64% down to 4.4%, while holding the pressure recovery constant. A second DOE optimization was performed holding the vanes heights at a constant value from the first DOE optimization with the two vane angles-of-attack as design factors. This DOE only required a second order model fit with 15 numerical simulation experiments and reduced DC60 to 3.5% with small decreases in the fourth and fifth harmonic amplitudes. The second optimal vane design was tested at the NASA Langley 0.3-Meter Transonic Cryogenic Tunnel in a BLI inlet experiment. The experimental results showed a 80% reduction of DPCPavg, the circumferential distortion level at the engine fan face.
Allan, Brian G.↗
Generation After Next Propulsor Research: Robust Design for Embedded Engine Systems
The National Aeronautics and Space Administration, United Technologies Research Center and Virginia Polytechnic and State University have contracted to pursue multi-disciplinary research into boundary layer ingesting (BLI) propulsors for generation after next environmentally responsible subsonic fixed wing aircraft. This Robust Design for Embedded Engine Systems project first conducted a high-level vehicle system study based on a large commercial transport class hybrid wing body aircraft, which determined that a 3 to 5 percent reduction in fuel burn could be achieved over a 7,500 nanometer mission. Both pylon-mounted baseline and BLI propulsion systems were based on a low-pressure-ratio fan (1.35) in an ultra-high-bypass ratio engine (16), consistent with the next generation of advanced commercial turbofans. An optimized, coupled BLI inlet and fan system was subsequently designed to achieve performance targets identified in the system study. The resulting system possesses an inlet with total pressure losses less than 0.5%, and a fan stage with an efficiency debit of less than 1.5 percent relative to the pylon-mounted, clean-inflow baseline. The subject research project has identified tools and methodologies necessary for the design of next-generation, highly-airframe-integrated propulsion systems. These tools will be validated in future large-scale testing of the BLI inlet / fan system in NASA's 8 foot x 6 foot transonic wind tunnel. In addition, fan unsteady response to screen-generated total pressure distortion is being characterized experimentally in a JT15D engine test rig. These data will document engine sensitivities to distortion magnitude and spatial distribution, providing early insight into key physical processes that will control BLI propulsor design.
Arend, David J.↗