Search NASA⌕ Search

SEARCH · Search NASA

Results for “BORON 10”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Comparison of CF4 and SF6 based plasmas for ECR etching of isotopically enriched 10Boron films

Isotopically enriched {sup 10}boron films have been successfully etched in an ECR etching tool using CF{sub 4} and SF{sub 6} based plasmas. Comparisons between the two are made with regards to etch rate, selectivity to the underlying Si device structure, and morphology of the {sup 10}boron post-etching. The present film etching development is expected to be critical for the fabrication of next generation thermal neutron solid state detectors based on {sup 10}boron.

42 ENGINEERING↗

Alternative Process for Manufacturing of Thin Layers of Boron for Neutron Measurement

Due to the worldwide shortage of helium 3, Boron-lined proportional counters are developed intensively by several groups. Up to now, thin boron containing layers for neutron detectors are essentially produced by sputtering of boron carbide (B{sub 4}C). This technology provides high quality films but it is slow and expensive. Our paper describes a novel and inexpensive technology for producing boron layers. This technology is based on chemical synthesis of boron 10 nanoparticles, and on electrophoretic deposition of these particles on metallic plates, or on metallic pieces with more complex shapes. The chemical synthesis consists in: - Heating boron 10 with lithium up to 700 deg. C under inert atmosphere: an intermetallic compound, LiB, is produced; - Hydrolysing this intermetallic compound: LiB + H{sub 2}O → B + Li{sup +} + OH{sup -} + 1/2H{sub 2}, where B is under the form of nanoparticles; - Purifying the suspension of boron nanoparticles in water, from lithium hydroxide, by successive membrane filtrations; - Evaporating the purified suspension, in order to get a powder of nanoparticles. The obtained nanoparticles have size around 300 nm, with a high porosity, of about 50%. This particle size is equivalent to about 150 nm massive particles. The nanoparticles are then put into suspension in a specific solvent, in order to perform deposition on metallic surfaces, by electrophoretic method. The solvent is chosen so that it is not electrolysed even under voltages of several tens of volts. An acid is dissolved into the solvent, so that the nanoparticles are positively charged. Deposition is performed on the cathode within about 10 min. The cathode could be an aluminium plate, or a nickel coated aluminium plate. Homogeneous deposition may also be performed on complex shapes, like grids in a Multigrid detector. A large volume of pieces, can be coated with a Boron-10 film in a few hours. The thickness of the layer can be adjusted according to the required neutron detection characteristics, between 0,5 to 5 μm (equivalent to 0,25 to 2.5 massive layer). The thickness is homogenous within a ±20% range. The layer is an almost pure {sup 10}B layer (90%). The ratio of the amount of deposed boron 10 to the amount of raw boron 10 used is more than 80%. Hence, another advantage of this technique is that Boron 10 will be deposited on the cathodes only, without loss of this expensive material. 2 grids of a Multi-Grid detector have been coated with pure Boron by using this technique. The film structure has been analysed with a microscope and the detector has been tested on a monochromatic neutron beam line. Preliminary results will be shown. (authors)

36 MATERIALS SCIENCE↗

10 Boron-film-based gas detectors at ESS

The development of detectors for the European Spallation Source is an important parallel element to the effort put into the design and construction of the neutron source and instruments. The 10Boron-film-based detector developments that started over a decade ago as basic detector concepts have now reached technical maturity after intense prototyping work and numerous testing campaigns. Several of the ESS beamlines that will soon enter the commissioning phase started welcoming the detector systems built with the 10 B-film converter technology. The real-size demonstrators evolved in the last 2–3 years into a diverse suite of gas proportional counters for use in diffraction, reflectometry and small-angle scattering studies in spite of the operational complexity posed by the requirements for large-area coverage, low material budget and robustness for operation in the high-flux and high-radiation environment of ESS. The detectors are now being shipped to ESS or undergoing the last performance and calibration tests before being handed over to the instrument teams for installation in the host beamlines. A common feature of these detector systems is the very large number of readout channels that they are instrumented with in order to fulfill the demanding requirements for sensitivity, spatial resolution and count-rate capability. Across all of the detector types that will operate at ESS, the integration, testing and commissioning of the read-out technologies and software tools for data reduction, calibration and analysis are the focus of the detector and integration teams. These will yield a wealth of knowledge about their operation as well as initial results on the in-situ performance, a very important asset to ensure rapid commissioning of the detectors when neutrons from the ESS source become available. In this paper we will give an overview of the 10 B-film-based detector technologies included in the ESS detector suite that are currently facing the transition from the production phase to installation and integration with the other beamline components, which comes with its own specific challenges of both organizational and technical nature.

47 OTHER INSTRUMENTATION↗

California GAMA Special Study: Stable isotopic composition of groundwater boron – Analytical method development

Boron is a ubiquitous dissolved constituent in natural waters due to its high solubility, natural occurrence in continental crust, and anthropogenic use in fertilizers, consumer products, and other non-natural sources. The two stable isotopes of boron, 10 B and 11 B (natural abundances ≈ 19.9 and ≈ 80.1 atom percent, respectively), undergo isotopic fractionation due to a variety of chemical processes related to boron speciation ( 10 B is preferentially incorporated into B(OH) 4 - versus B(OH) 3 , e.g. Byrne et al., 2006). The isotopic composition of dissolved boron in groundwater can be used to determine the source(s) of boron; this information can be used to infer the source(s) of other co-migrating contaminants (e.g. nitrate, pharmaceuticals, etc.). Boron behaves as a conservative element in groundwater and surface water systems (Barth, 2000), and the isotopic signature of boron is most useful in conjunction with other stable and radiogenic isotope systems (e.g. δ 18 O, δ 15 N, δ 13 C, 87 Sr/ 86 Sr; Tirez et al., 2010; Widory et al., 2004; Widory et al., 2005) to determine the source(s) of contaminants of interest. We present here a method for boron purification in natural water samples (groundwater, surface water, and seawater) by ion exchange chemistry and measurement of boron isotopic composition by MC-ICP-MS. These methods can be applied to samples with boron concentrations as low as 10 ppb with precision on δ 11 B measurements better than ± 1 ‰. We utilize boron isotopic measurements of boric acid, groundwater, and seawater standards to validate the methods. We also present boron isotopic measurements of San Diego County domestic well samples to demonstrate how these methods can be applied to any study of natural water samples.

07 ISOTOPE AND RADIATION SOURCES↗

Self-powered micro-structured solid state neutron detector with very low leakage current and high efficiency

We report on the design, fabrication, and performance of solid-state neutron detector based on three-dimensional honeycomb-like silicon micro-structures. The fabricated detectors use boron filled deep holes with aspect ratio of over 12 and showed a very low leakage current density of {approx}7 Multiplication-Sign 10{sup -7} A/cm{sup 2} at -1 V for device sizes varying from 2 Multiplication-Sign 2 to 5 Multiplication-Sign 5 mm{sup 2}. A thermal neutron detection efficiency of 4.5% {+-} 0.5% with discrimination setting of 500 keV and gamma to neutron sensitivity of (1.1 {+-} 0.1) Multiplication-Sign 10{sup -5} for single layer was measured without external bias for these devices. Monte-Carlo simulation predicts a maximum efficiency of 45% for such devices filled with 95% enriched {sup 10}boron.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Analysis of T = 1 {sup 10}B States Analogue to {sup 10}Be Cluster States

Current status of the search for T = 1 cluster states in {sup 10}Be, {sup 10}B and {sup 10}C is presented. The best known of the three, {sup 10}Be, has an established rotational band (6.18, 7.54 and 10.15 MeV) with unusually large moment of inertia. Search of their isobaric analogue in {sup 10}B is presented, with emphasis on {sup 3}He+{sup 11}B reaction.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Hexagonal Uniformly Redundant Arrays (HURAs) for scintillator based coded aperture neutron imaging

A series of Monte Carlo simulations have been conducted, making use of the EJ-426 neutron scintillator detector, to investigate the potential of using hexagonal uniformly redundant arrays (HURAs) for scintillator based coded aperture neutron imaging. This type of scintillator material has a low sensitivity to gamma rays, therefore, is of particular use in a system with a source that emits both neutrons and gamma rays. The simulations used an AmBe source, neutron images have been produced using different coded-aperture materials (boron- 10, cadmium-113 and gadolinium-157) and location error has also been estimated. In each case the neutron image clearly shows the location of the source with a relatively small location error. Neutron images with high resolution can be easily used to identify and locate nuclear materials precisely in nuclear security and nuclear decommissioning applications. (authors)

42 ENGINEERING↗

Isospin in halo nuclei: Borromean halo, tango halo, and halo isomers

It is shown that the wave functions for isobaric analog, double isobaric analog, configuration, and double configuration states may simultaneously have components corresponding to nn, np, and pp halos. The difference in the halo structure between the ground and excited states of a nucleus may lead to the formation of halo isomers. A halo structure of both Borromean and tango types can be observed for np configurations. The structure of ground and excited states with various isospins in halo-like nuclei is discussed. The reduced probabilities B(Mλ) and B(Eλ) for gamma transitions in {sup 6−8}Li, {sup 8−10}Be, {sup 8,10,11}B, {sup 10−14}C, {sup 13−17}N, {sup 15−17,19}O, and {sup 17}F nuclei are analyzed. Particular attention is given to the cases where the ground state of a nucleus does not have a halo structure, but where its excited state may have it.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Demonstration of Full Core Reactor Depletion with MPACT

MPACT is a three-dimensional (3-D) whole core transport code capable of generating sub-pin level power distributions. This feature is accomplished by obtaining the integral transport solutions to the heterogeneous reactor problem in which the actual detailed geometrical configuration of fuel components such as the pellet and cladding is modelled explicitly.. The cross section data needed for the neutron transport calculation are obtained directly from a multigroup microscopic cross section library similar to those used in lattice physics codes. Hence MPACT involves neither a priori homogenization nor group condensation for the core spatial solution. The integral transport solution is obtained by means of the method of characteristics (MOC) that employs discrete ray tracing. Since the direct application of the 3-D MOC capability in MPACT to 3-D core configuration requires considerable amounts of memory and computing time for practical reactor applications, an alternative approximate 3-D solution method was implemented in MPACT based on a 2D-1D approach which employs planar MOC solutions in the framework of the 3-D coarse mesh finite difference (CMFD) formulation. The axial coupling is resolved by one-dimensional (1-D) diffusion solutions and the planar and axial problems are coupled through the transverse leakage. The use of a lower order 1-D solution in the axial direction is justified by the fact that most heterogeneity in the core occurs in the radial direction rather than the axial. However, it is possible to use one of the higher order methods in MPACT such as the 1-D SN kernel if improved solution accuracy is desired. The CMFD formulation which originally served as an efficient nodal formulation is used in MPACT to accelerate the whole core transport calculation. The basic mesh in the CMFD formulation is a pin cell which is much coarser than the flat source regions defined for MOC calculations. The concept of dynamic homogenization of group constants for the pin cells provides the basis of the CMFD formulation in whole core transport calculation. The intra-cell flux distribution determined from the MOC calculation is used to generate the homogenized cell constants while the MOC cell surface averaged currents are used to determine the radial nodal coupling coefficients. This dynamic implementation of the equivalence theory formulation ensures the same transport solution is obtained with CMFD as the one obtained using unaccelerated MOC calculations alone. The ability of MPACT to predict the Hot, Zero Power (HZP) condition of a reactor was reported in CASL-U-2014-0045-000. The purpose of this report is to demonstrate the capability of MPACT to simulate the operation of a reactor at Hot, Full Power (HFP) conditions during normal operation throughout a full operating cycle. The time scale for a reactor burnup cycle is typically one to two years and therefore short time phenomena such as the effect of delayed neutrons can be neglected. Instead the time dependence can be treated quasi-statically using the depletion algorithm presented in CASL-U-2013-0276-001. The full power operation requires thermal hydraulic feedback to be present during the entire simulation which will utilize the work in CASL-U-2014-0051-000. However, due to the significant computational burden of the coupled physics simulation, a simplified thermal hydraulic model is used for the analysis reported here which is principally intended to demonstrate the full core neutronics depletion. In addition to the thermal hydraulic feedback, the effect of Boron 10 depletion should be modeled in cases where major boron additions are not performed for extended periods of time. Each of these capabilities will be described in the following sections.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Modeling Tungsten Boride Neutronics in ORIGEN for Z-Facility

ORIGEN is one of the main transmutation software packages used in nuclear engineering Modeling Tungsten Boride Neutronics in ORIGEN for Z-Facilityproblems. For the case of this study, tungsten borides are studied using a coupled framework between MCNP and the ORIGEN package of scale. The input used four compositions of tungsten boride: WB with natural boron- 10 abundance, WB with 80wt% B-10 per isotope of boron, WB4 with natural boron-10 abundance, and WB4 with 80wt% B-10 per isotope of boron. Isotopic inventories were produced for WB which show the time dependent change up to 2 years after a 6-Month irradiation. This will allow for further studies of the materials to assess things material composition changes, dose contribution, and waste management requirements.

36 MATERIALS SCIENCE↗

Enriched Boron-Doped Amorphous Selenium Based Position-Sensitive Solid-State Thermal Neutron Detector for MPACT Applications

High-efficiency thermal neutron detectors with compact size, low power-rating and high spatial, temporal and energy resolution are essential to execute non-proliferation and safeguard protocols. The demands of such detector are not fully covered by the current detection system such as gas proportional counters or scintillator-photomultiplier tube combinations, which are limited by their detection efficiency, stability of response, speed of operation, and physical size. Furthermore, world-wide shortage of 3 He gas, required for widely used gas detection method, has further prompted to design an alternative system. Therefore, a solid-state neutron detection system without the requirement of 3 He will be very desirable. To address the above technology gap, we had proposed to develop new room temperature solidstate thermal neutron detectors based on enriched boron ( 10 B) and enriched lithium ( 6 Li) doped amorphous Se (As- 0.52%, Cl 5 ppm) semiconductor for MPACT applications. The proposed alloy materials have been identified for its many favorable characteristics - a wide bandgap (~2.2 eV at 300 K) for room temperature operation, high glass transition temperature (t g ~ 85°C), a high thermal neutron cross-section (for boron ~ 3840 barns, for lithium ~ 940 barns, 1 barn = 10 -24 cm 2 ), low effective atomic number of Se for small gamma ray sensitivity, and high radiation tolerance due to its amorphous structure.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Boron mullite: Formation and basic characterization

Graphical abstract: Display Omitted Highlights: ► Decrease of B-mullite formation temperature with increasing boron content. ► Decrease of lattice parameters b and c with increasing boron content. ► Significant reduction of thermal expansion (−15%) due to incorporation of boron. ► Decomposition of B-mullite at 1400 °C, long-term stability at 800 °C. -- Abstract: A series of boron doped mullites (B-mullite) was prepared from single-phase gels with initial compositions based on a 1:1 isomorphous substitution of Si by B, starting from a 3:2 mullite composition (Al{sub 4.5}Si{sub 1.5}O{sub 9.75}). A high amount of boron (>10 mol.%) can be incorporated into the crystal structure of mullite where it most likely replaces Si. In situ phase formation of B-mullites was studied with high temperature X-ray diffraction and thermal analysis. A decrease of the formation temperature for B-mullite with increasing boron content was observed. With increasing boron content lattice parameters b and c significantly decrease, while no systematic evolution of a is observed. Long annealing at 1400 °C results in decomposition of B-mullite to boron free mullite and α-alumina. At 800 °C B-mullite appears to be stable over a period of at least 12 days. The mean thermal expansion coefficient was reduced by 15% upon incorporation of boron which makes the material technologically interesting.

36 MATERIALS SCIENCE↗

Continuous measurement of boron concentration in nuclear power plants: why is it essential for safe and efficient operation? - 318

As a neutron-absorber, Boron 10 plays a significant role in nuclear power plants as it is used in order to control reactivity in the core, together with control rods. For that reason; it is a key parameter that has to be controlled. In a similar way, it is crucial to be able to detect a boron dilution in the primary circuit, as it would causes severe damages if not detected and controlled. Thus, it comes as evidence that a boron concentration monitoring system is a key for every nuclear power plant. Consequently, it becomes important to provide plant operators with a boron concentration measurement issued by a reliable, redundant, classified and qualified system, with high accuracy and short response time. In order to cover this need, Rolls-Royce has designed Boronline{sup R}, the latest generation of boron meter, which provides nuclear power plant operators with a permanent record of boron concentration of primary circuit by way of continuous sampling and real-time measurements. Boronline takes part of a new generation of Advanced Sensors and Measurements Technologies. In this paper, boron meter role, main functions and measuring principles will be detailed, as well as technical characteristics of the new generation of boron meter will be presented. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Calculation of boron-isotope fractionation between B(OH)(3)(aq) and B(OH)(4)(-)(aq)

Density functional and correlated molecular orbital calculations (MP2) are carried out on B(OH)3-nH2O clusters (n = 0, 6,32), and B(OH)-4.nH20 (n = 0, 8, 11, 32) to estimate the equilibrium distribution of 10B and 11B isotopes between boric acid and borate in aqueous solution. For the large 32-water clusters, multiple conformations are generated from ab initio molecular dynamics simulations to account for the effect of solvent fluctuations on the isotopic fractionation. We provide an extrapolated value of the equilibrium constant x34 for the isotope exchange reaction 10B(OH)3(aq) + 11B(OH)-4 (aq) = 11B(OH)3(aq) + 11B(OH)-4 (aq) of 1.026-1.028 near the MP2 complete basis set limit with 32 explicit waters of solvation. With some exchange-correlation functionals we find potentially important contributions from a tetrahedral neutral B(OH)3.H2O Lewis acid-base complex. The extrapolations presented here suggest that DFT calculations give a value for 103lnx34 about 15% higher than the MP2 calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Radiation Shielding Options for the Affordable Fission Surface Power System

The Affordable Fission Surface Power System (AFSPS) is a proposed power source for an outpost capable of housing six humans for up to six weeks on the lunar surface and emphasizes the design principles of low risk and affordability over high performance. The radiation shield is the most massive component of the reactor system and its effect on launch mass greatly affects the affordability of the AFSPS. Potential shielding materials include lithium hydride, enriched boron-10 carbide, water, borated water, beryllium, boron-doped beryllium and zirconium hydride. Zirconium hydride is the most effective neutron attenuator and also significantly attenuates gamma radiation, but at a significant mass penalty. The other neutron attenuating materials all require the addition of a tungsten layer to provide significant gamma attenuation. Based on neutron radiation alone, lithium hydride is the lightest of the potential attenuators, followed by water and borated water. When gamma radiation is also considered, the lithium hydride/tungsten shield is shown to be the lightest composite shield with a combined mass of 3246 kg, followed by the borated water/tungsten shield (3479 kg). The boron carbide/tungsten shield has a total mass of 4129 kg, but represents significantly less development risk.

36 MATERIALS SCIENCE↗

Prompt Neutron Multiplicity Measurements with Portable Detectors

Mobile detection of kilogram quantities of special nuclear materials (SNM) during maritime transportation is a challenging problem for the U.S. Department of Homeland Security. Counting neutrons emitted by the SNM and partitioning them from background neutrons of multiple origins is the most effective passive means of detecting the SNM. Unfortunately, neutron detection, counting, and partitioning in a maritime environment is complex due to the presence of spallation neutrons (commonly known as “ship effect”) and to the complicated nature of the neutron scattering in that environment. This work studied the possibilities of building a prototype neutron detector using boron- 10 (10B) as the converter in a novel form factor called “straws” that would address the above problem by examining multiplicity distributions of neutrons originating from a fissioning source. Currently, commercially manufactured fission meters (FM) are available that separate cosmic neutrons from non-cosmic neutrons and quantitatively determine the strength of a fissioning source; however, these FMs use 3He, which is becoming increasingly difficult to procure; also the size and weight of a commercial FM is not conducive to manual neutron detection operations in a maritime environment. The current project may provide a near-term solution to the crisis that has arisen from the global scarcity of 3He by offering a viable alternative to the FM. The prototype detector provides a large-area, efficient, lightweight, more granular neutron responsive detection surface (to facilitate imaging) to ease the application of the new FMs. A novel prototype fission meter is being designed at National Security Technologies, LLC, using a thin uniform coating of 10B as neutron converter (only 1 micron thick) inside a large array of thin (4 mm diameter) copper tubes. The copper tubes are only 2-mil thick, and each holds the stretched anode wire under tension and high voltage. The tubes are filled with proportional counter gas (a mixture of 90% Ar and 10% CO2). The tubes operate in proportional counter mode and attract mobile charged particles (alpha-particles) created in the nuclear interaction 10B(n, a)7Li. Several MCNPX calculations covering the substantial design parameter space of neutron multiplicity detectors have been performed and are presented. Our detector’s thermal neutron detection efficiency is compared to two Ortec commercial products, the Fission Meter and Detective-EX. Pulse height spectra originating from the charged particles created in the nuclear reaction 10B(n, a) 7Li* + 2.310 MeV (94%) – excited state (1) and 10B(n, a) 7Li + 2.792 MeV (6%) – ground state (2) are examined, and the response to incident gamma rays are demonstrated.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Introduction to Neutron Coincidence Counter Design Based on Boron-10

The Department of Energy Office of Nonproliferation Policy (NA-241) is supporting the project 'Coincidence Counting With Boron-Based Alternative Neutron Detection Technology' at Pacific Northwest National Laboratory (PNNL) for development of an alternative neutron coincidence counter. The goal of this project is ultimately to design, build and demonstrate a boron-lined proportional tube based alternative system in the configuration of a coincidence counter. This report, providing background information for this project, is the deliverable under Task 1 of the project.

10B↗