The OSO 1 solar neutron experiment
Solar neutron detection by OSO- I satellite carrying boron fluoride detector
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Solar neutron detection by OSO- I satellite carrying boron fluoride detector
Solar neutron observations with boron fluoride counter on OSO-1, discussing absence of diurnal variation
The luminescence-spectral, lasing and photochemical characteristics of laser media based on boron fluoride complexes of dipyrromethenes, embedded into solid bulk matrices of polymethylmethacrylate and its modifications (obtained by adding polyhedral oligomeric silsesquioxane during polymerisation) and into polymer films, in which polyhedral silsesquioxane enters the composition of monomeric unit, have been investigated. (lasers)
Plasma doping has been accepted into semiconductor manufacturing for two low energy, high dose implant applications. The p-type polysilicon counter-doping and contact doping for DRAM devices can be carried out using BF{sub 3} or B{sub 2}H{sub 6} precursor gas. The choice between these two precursors depends on the benefits and constraints of each one. In order to identify these benefits and constraints, the boron dopant profile responses to dose variation for both precursors have been studied using the PULSION plasma doping tool.
A planar magnetron sputtering device with thermally isolated sintered boron target has been designed and demonstrated. The magnetron is intended to use for generation of boron ion beams, as well as in plasma immersion implantation. For a boron target, high target temperature is required because boron has low electrical conductivity at room temperature, which increases with temperature. The target is well insulated thermally and can be heated by an initial low-current, high-voltage DC discharge mode. A discharge power of 16 W was adequate to reach the required surface temperature, after that a transition of the discharge to a high-current, low-voltage mode is observed. Applying high current pulses over the DC heating discharge results in a self-sputtering operational mode of the magnetron discharge. Ion beam was extracted from the discharge plasma. Beam analysis was performed with a time-of-flight system. All the boron ions are single charged. The maximum boron ion fraction in the beam is greater than 99%, and the mean boron ion fraction, time-integrated over the whole pulse length, is about 95%. This kind of boron ion source could be competitive to conventional boron ion sources that utilize compounds such as BF{sub 3}, and could be useful for semiconductor industry application.
{sup 3}He filled position sensitive detectors (PSD)s developed in-house are successfully used for neutron scattering studies at Dhruva. However recent global scarcity of {sup 3}He has made it essential to find an alternative. It is very difficult to meet performance capabilities of {sup 3}He for neutron detection in any of the alternate materials. Among various alternatives, BF{sub 3} gas can be one. We have recently put an effort to evaluate performance of BF{sub 3} based PSD. For that a PSD filled with BF{sub 3} gas at 0.8 bar pressure is fabricated and characterized. Performances of the same with Pu-Be source and at Hi-Q Diffractometer, Dhruva are reported in this paper. Diffraction spectra from standard samples Fe and Si at wavelength 0.783 A were recorded. It is found that while position resolution of the BF{sub 3} filled PSD is comparable but the efficiency is 20 times less than that of a {sup 3}He(12 bar) filled PSD.
Fluorine implantation process purity was considered on different types of high current implanters. It was found that implanters equipped with an indirectly heated cathode ion source show an enhanced deep boron contamination compared to a high current implanter using a cold RF-driven multicusp ion source when boron trifluoride is used for fluorine implantations. This contamination is directly related to the source technology and thus, should be considered potentially for any implanter design using hot cathode/hot filament ion source, independently of the manufacturer.The boron contamination results from the generation of double charged boron ions in the arc chamber and the subsequent charge exchange reaction to single charged boron ions taking place between the arc chamber and the extraction electrode. The generation of the double charged boron ions depends mostly on the source parameters, whereas the pressure in the region between the arc chamber and the extraction electrode is mostly responsible for the charge exchange from double charged to single charged ions. The apparent mass covers a wide range, starting at mass 11. A portion of boron ions with energies of (19/11) times higher than fluorine energy has the same magnetic rigidity as fluorine beam and cannot be separated by the analyzer magnet. The earlier described charge exchange effects between the extraction electrode and the entrance to the analyzer magnet, however, generates boron beam with a higher magnetic rigidity compared to fluorine beam and cannot cause boron contamination after mass-separation.The energetic boron contamination was studied as a function of the ion source parameters, such as gas flow, arc voltage, and source magnet settings, as well as analyzing magnet aperture resolution. This allows process optimization reducing boron contamination to the level acceptable for device performance.
In the system BaF{sub 2}/BF{sub 3}/PF{sub 5}/anhydrous hydrogen fluoride (aHF) a compound Ba(BF{sub 4})(PF{sub 6}) was isolated and characterized by Raman spectroscopy and X-ray diffraction on the single crystal. Ba(BF{sub 4})(PF{sub 6}) crystallizes in a hexagonal P6-bar2m space group with a=10.2251(4) A, c=6.1535(4) A, V=557.17(5) A{sup 3} at 200 K, and Z=3. Both crystallographically independent Ba atoms possess coordination polyhedra in the shape of tri-capped trigonal prisms, which include F atoms from BF{sub 4}{sup -} and PF{sub 6}{sup -} anions. In the analogous system with AsF{sub 5} instead of PF{sub 5} the compound Ba(BF{sub 4})(AsF{sub 6}) was isolated and characterized. It crystallizes in an orthorhombic Pnma space group with a=10.415(2) A, b=6.325(3) A, c=11.8297(17) A, V=779.3(4) A{sup 3} at 200 K, and Z=4. The coordination around Ba atom is in the shape of slightly distorted tri-capped trigonal prism which includes five F atoms from AsF{sub 6}{sup -} and four F atoms from BF{sub 4}{sup -} anions. When the system BaF{sub 2}/BF{sub 3}/AsF{sub 5}/aHF is made basic with an extra addition of BaF{sub 2}, the compound Ba{sub 2}(BF{sub 4}){sub 2}(AsF{sub 6})(H{sub 3}F{sub 4}) was obtained. It crystallizes in a hexagonal P6{sub 3}/mmc space group with a=6.8709(9) A, c=17.327(8) A, V=708.4(4) A{sup 3} at 200 K, and Z=2. The barium environment in the shape of tetra-capped distorted trigonal prism involves 10 F atoms from four BF{sub 4}{sup -}, three AsF{sub 6}{sup -} and three H{sub 3}F{sub 4}{sup -} anions. All F atoms, except the central atom in H{sub 3}F{sub 4} moiety, act as mu{sub 2}-bridges yielding a complex 3-D structural network. - Graphical abstract: The first three compounds, containing simultaneously tetrahedral BF{sub 4}{sup -} and octahedral AF{sub 6}{sup -} (A=P, As) anions have been synthesized and characterized by Raman spectroscopy and X-ray single crystal diffraction. In the system BaF{sub 2}/BF{sub 3}/PF{sub 5}/anhydrous hydrogen fluoride (aHF) the compound Ba(BF{sub 4})(PF{sub 6}) was isolated. In the analogous system with AsF{sub 5} instead of PF{sub 5} the compound Ba(BF{sub 4})(AsF{sub 6}) was obtained. When the system BaF{sub 2}/BF{sub 3}/AsF{sub 5}/aHF is made basic with an extra addition of BaF{sub 2}, the compound Ba{sub 2}(BF{sub 4}){sub 2}(AsF{sub 6})(H{sub 3}F{sub 4}) was prepared.
Directly heated high temperature cathodes of refractory metals such as tungsten run electric current of more than several tens of amperes. The electric current makes magnetic field around the cathode wire, and the magnetic field causes inhomogeneous emission of electrons from the cathode. To solve this problem we have designed the cathode having a co-axial heater current flow structure, and mounted it in a Bernas-type ion source. A plasma produced by co-axial hot cathode showed a clearer column along the external magnetic field and less displacement in the direction perpendicular to the field than that produced by a hair-pin filament. Stable discharge current as high as 5000 mA was obtained for Ar and BF{sub 3} gases with the co-axial cathode. Boron and phosphorus ion beams were extracted from the source on an actual ion implanter. The ion beam currents were 1.5 times as large as those obtained with a hair-pin filament.
We investigated the application properties of cluster implantation for MSA processing. We successfully replaced BF{sub 2} with B{sub 18}H{sub 22} to SDE implantation in pMOSFETs with the activation processing of MSA and spike-RTA. In the activation processing with only MSA, we found from blank wafer that B{sub 18}H{sub 22} implant is more advantageous from the viewpoint of R{sub s}, X{sub j} and leakage current, compared to B, BF{sub 2} and B with Ge-PAI00.
Basic characteristics of ClusterBoron (B{sub 18}H{sub 22}) implantation were investigated for improving contact resistance in DRAM devices. Generally, {sup 49}BF{sub 2} has been widely used for contact implant application in DRAM manufacturing because of its higher productivity compared to monomer boron ({sup 11}B). However, because of limited activation in a low thermal budget ({approx}800 deg. C) anneal, the sheet resistance was saturated for doses over 5x10{sup 15} ions/cm{sup 2}. Although many investigations have been reported, such as {sup 30}BF implant mixed implant with monomer boron etc., no practical solution has been found for dramatic improvement of contact resistance in a productive manner. B{sub 18}H{sub 22} was developed to overcome the productivity limitations encountered in low energy, high dose boron implantation and the limited activation of {sup 49}BF{sub 2} due to co-implanted fluorine. In this study, basic characterization of the B{sub 18}H{sub 22} contact implant was performed through sheet resistance, SIMS (Secondary Ion Mass Spectrometry) and XTEM (cross-sectional transmission electron microscopy). The B{sub 18}H{sub 22} implants showed lower sheet resistance than conventional {sup 49}BF{sub 2} for 5x10{sup 15} ions/cm{sup 2} on bare wafer tests. Through XTEM study, we found the activation behavior of both B{sub 18}H{sub 22} and {sup 49}BF{sub 2} were directly related with the amorphous layer thickness and residual defects from low thermal budget anneal. PMOS contact resistance in the sub-70 nm device by B{sub 18}H{sub 22} implantation showed considerable improvement (about 30%), showing B{sub 18}H{sub 22} could replace the BF{sub 2} for contact implant in contact resistance implant.
Plasma doping (PLAD) shows very different impurity profiles compared to the conventional beam-line-based ion implantations due to its non-mass separation property and plasma environment. There is no simulation for PLAD process so far due to a lack of a dopant profile model. Several factors determine impurity profiles of PLAD process. The most significant factors are: plasma chemistry and deposition/etching characteristics of multi-ion species plasmas. In this paper, we present plasma chemistry and deposition/etching characteristics of PLAD processes versus co-gas dilutions. Four dopant plasmas including B{sub 2}H{sub 6}, BF{sub 3}, AsH{sub 3}, and PH{sub 3}, and two non-dopant plasmas including CH{sub 4} and GeH{sub 4} are studied and demonstrated.
A thermally stable negative electron affinity (NEA) for a cubic boron nitride (c-BN) surface with vanadium-oxide-termination is achieved, and its electronic structure was analyzed with in-situ photoelectron spectroscopy. The c-BN films were prepared by electron cyclotron resonance plasma-enhanced chemical vapor deposition employing BF{sub 3} and N{sub 2} as precursors. Vanadium layers of ∼0.1 and 0.5 nm thickness were deposited on the c-BN surface in an electron beam deposition system. Oxidation of the metal layer was achieved by an oxygen plasma treatment. After 650 °C thermal annealing, the vanadium oxide on the c-BN surface was determined to be VO{sub 2}, and the surfaces were found to be thermally stable, exhibiting an NEA. In comparison, the oxygen-terminated c-BN surface, where B{sub 2}O{sub 3} was detected, showed a positive electron affinity of ∼1.2 eV. The B{sub 2}O{sub 3} evidently acts as a negatively charged layer introducing a surface dipole directed into the c-BN. Through the interaction of VO{sub 2} with the B{sub 2}O{sub 3} layer, a B-O-V layer structure would contribute a dipole between the O and V layers with the positive side facing vacuum. The lower enthalpy of formation for B{sub 2}O{sub 3} is favorable for the formation of the B-O-V layer structure, which provides a thermally stable surface dipole and an NEA surface.
Passivated contacts (poly-Si/SiO{sub x}/c-Si) doped by shallow ion implantation are an appealing technology for high efficiency silicon solar cells, especially for interdigitated back contact (IBC) solar cells where a masked ion implantation facilitates their fabrication. This paper presents a study on tunnel oxide passivated contacts formed by low-energy ion implantation into amorphous silicon (a-Si) layers and examines the influence of the ion species (P, B, or BF{sub 2}), the ion implantation dose (5 × 10{sup 14 }cm{sup −2} to 1 × 10{sup 16 }cm{sup −2}), and the subsequent high-temperature anneal (800 °C or 900 °C) on the passivation quality and junction characteristics using double-sided contacted silicon solar cells. Excellent passivation quality is achieved for n-type passivated contacts by P implantations into either intrinsic (undoped) or in-situ B-doped a-Si layers with implied open-circuit voltages (iV{sub oc}) of 725 and 720 mV, respectively. For p-type passivated contacts, BF{sub 2} implantations into intrinsic a-Si yield well passivated contacts and allow for iV{sub oc} of 690 mV, whereas implanted B gives poor passivation with iV{sub oc} of only 640 mV. While solar cells featuring in-situ B-doped selective hole contacts and selective electron contacts with P implanted into intrinsic a-Si layers achieved V{sub oc} of 690 mV and fill factor (FF) of 79.1%, selective hole contacts realized by BF{sub 2} implantation into intrinsic a-Si suffer from drastically reduced FF which is caused by a non-Ohmic Schottky contact. Finally, implanting P into in-situ B-doped a-Si layers for the purpose of overcompensation (counterdoping) allowed for solar cells with V{sub oc} of 680 mV and FF of 80.4%, providing a simplified and promising fabrication process for IBC solar cells featuring passivated contacts.
Although the diffusion control and dopant activation of Ge p-type junctions are straightforward when using B{sup +} implantation, the use of the heavier BF{sub 2}{sup +} ions or even BF{sup +} is still favored in terms of shallow junction formation and throughput—because implants can be done at higher energies, which can give higher beam currents and beam stability—and thus the understanding of the effect of F co-doping becomes important. In this work, we have investigated diffusion and end-of-range (EOR) defect formation for B{sup +}, BF{sup +}, and BF{sub 2}{sup +} implants in crystalline and pre-amorphized Ge, employing rapid thermal annealing at 600 °C and 800 °C for 10 s. It is demonstrated that the diffusion of B is strongly influenced by the temperature, the presence of F, and the depth of amorphous/crystalline interface. The B and F diffusion profiles suggest the formation of B–F complexes and enhanced diffusion by interaction with point defects. In addition, the strong chemical effect of F is found only for B in Ge, while such an effect is vanishingly small for samples implanted with F alone, or co-implanted with P and F, as evidenced by the high residual F concentration in the B-doped samples after annealing. After 600 °C annealing for 10 s, interstitial-induced compressive strain was still observed in the EOR region for the sample implanted with BF{sup +}, as measured by X-ray diffraction. Further analysis by cross-sectional transmission electron microscopy showed that the {311} interstitial clusters are the majority type of EOR defects. The impact of these {311} defects on the electrical performance of Ge p{sup +}/n junctions formed by BF{sup +} implantation was evaluated.
Ultrathin and conformal boron-containing atomic layer deposition (ALD) films could be used as a shallow dopant source for advanced transistor structures in microelectronics manufacturing. With this application in mind, diboron tetrafluoride (B{sub 2}F{sub 4}) was explored as an ALD precursor for the deposition of boron containing films. Density functional theory simulations for nucleation on silicon (100) surfaces indicated better reactivity of B{sub 2}F{sub 4} in comparison to BF{sub 3}. Quartz crystal microbalance experiments exhibited growth using either B{sub 2}F{sub 4}-H{sub 2}O for B{sub 2}O{sub 3} ALD, or B{sub 2}F{sub 4}-disilane (Si{sub 2}H{sub 6}) for B ALD, but in both cases, the initial growth per cycle was quite low (≤0.2 Å/cycle) and decreased to near zero growth after 8–30 ALD cycles. However, alternating between B{sub 2}F{sub 4}-H{sub 2}O and trimethyl aluminum (TMA)-H{sub 2}O ALD cycles resulted in sustained growth at ∼0.65 Å/cycle, suggesting that the dense –OH surface termination produced by the TMA-H{sub 2}O combination enhances the uptake of B{sub 2}F{sub 4} precursor. The resultant boron containing films were analyzed for composition by x-ray photoelectron spectroscopy, and capacitance measurements indicated an insulating characteristic. Finally, diffused boron profiles less than 100 Å were obtained after rapid thermal anneal of the boron containing ALD film.
Boron 11 nuclear quadrupole coupling constants in solid boron halides, finding fine structure on nuclear magnetic resonance in boron fluoride
Oxygen difluoride-diborane reaction kinetics and boron fluoride formation rate