Search NASA⌕ Search

SEARCH · Search NASA

Results for “BOUNDARY LAYER - WING SECTIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

A study of the factors affecting boundary layer two-dimensionality in wind tunnels

The effect of screens, honeycombs, and centrifugal blowers on the two-dimensionality of a boundary layer on the test section floors of low-speed blower tunnels is studied. Surveys of the spanwise variation in surface shear stress in three blower tunnels revealed that the main component responsible for altering the spanwise properties of the test section boundary layer was the last screen, thus confirming previous findings. It was further confirmed that a screen with varying open-area ratio, produced an unstable flow. However, contrary to popular belief, it was also found that for given incoming conditions and a screen free of imperfections, its open-area ratio alone was not enough to describe its performance. The effect of other geometric parameters such as the type of screen, honeycomb, and blower were investigated. In addition, the effect of the order of components in the settling chamber, and of wire Reynolds number were also studied.

Mehta, R. D.↗
NASA NTRS1974

Reduction of acoustic disturbances in the test section of supersonic wind tunnels by laminarizing their nozzle and test section wall boundary layers by means of suction

The feasibility of quiet, suction laminarized, high Reynolds number (Re) supersonic wind tunnel nozzles was studied. According to nozzle wall boundary layer development and stability studies, relatively weak area suction can prevent amplified nozzle wall TS (Tollmien-Schlichting) boundary layer oscillations. Stronger suction is needed in and shortly upstream of the supersonic concave curvature nozzle area to avoid transition due to amplified TG (Taylor-Goertler) vortices. To control TG instability, moderately rapid and slow expansion nozzles require smaller total suction rates than rapid expansion nozzles, at the cost of larger nozzle length Re and increased TS disturbances. Test section mean flow irregularities can be minimized with suction through longitudinal or highly swept slots (swept behind local Mach cone) as well as finely perforated surfaces. Longitudinal slot suction is optimized when the suction-induced crossflow velocity increases linearly with surface distance from the slot attachment line toward the slot (through suitable slot geometry). Suction in supersonic blowdown tunnels may be operated by one or several individual vacuum spheres.

Pfenninger, W.↗
NASA NTRSDate not supplied

Review of IRT CFD & Diffuser Study Results - February 2024 Test Entries

In February 2024, multiple test entries were conducted in the NASA Glenn Research Center Icing Research Tunnel (IRT) to collect CFD validation data, particularly near the facility heat exchanger inlet and outlet planes, measure the boundary layer characteristics in the test section, and survey the diffuser flow field. The CFD validation testing utilized ultrasonic anemometers to acquire 3-components of flow velocity at the inlet and outlet planes across a row of heat exchanger blocks. The test section boundary layer surveys used 18-inch boundary layer rakes centered on each of the four test section surfaces with pitot tubes at turntable centerline. The diffuser study included surveys at three streamwise positions within the diffuser with a 5-hole flow angularity probe at between 3 and 7 lateral locations at a given streamwise position. All IRT diffuser data were acquired with the flow angularity probe at the centerline of the test section. An ultrasonic anemometer was also used in the diffuser to survey near-wall velocity profiles.

Icing↗
NASA NTRS1973

Boundary-layer losses

The primary cause of losses in a turbine is the boundary layer that builds up on the blade and end-wall surfaces. Analytical and experimental methods for determining the friction, trailing edge, and mixing losses associated with the boundary layer are reported. The theory presented herein refers primarily to two dimensional blade section boundary layers. Methods for obtaining three dimensional blade plus end wall losses from the two-dimensional results are also discussed.

Herman W Prust, Jr.↗
NASA NTRSDate not supplied

Development and Assessment of a New Particle Image Velocimetry System in the NASA GRC 225 cm2 Wind Tunnel

As part of an ongoing campaign to provide detailed and thorough measurements in a two-dimensional impinging shock-wave/boundary-layer interaction (SWBLI), a custom implementation of the Particle Image Velocimetry (PIV) measurement technique in the NASA Glenn 225 cm2 Wind Tunnel was constructed. The flow seeding apparatus was devised to locally seed the region of interest in the overall flowfield to avoid coating the viewing window with seed material. The ability of the PIV system to provide small particles which faithfully track the underlying gas-phase flowfield was of key importance for the success of this system to make quality measurements in the SWBLI flowfield. In order to optimize and assess the performance of the particle seeding system, PIV measurements were made across a planar oblique shock wave and particle response was analyzed to quantify the particle lag effects due to the finite inertia of the seed droplets. Video recordings from a camera placed in the wind tunnel plenum tank were also used to discern the near-field behavior of the seeded plume and guide the design evolution of the seeding apparatus. The resulting optimized seeding configuration was applied to make PIV measurements in the wind tunnel test section boundary layer to assess the seed particle spatial coverage and concentration. This sample boundary layer dataset provides an analog to the eventual boundary layer measurements to be made in the axisymmetric test section under much more challenged viewing conditions.

PIV↗
NASA NTRSDate not supplied

Development and Assessment of a New Particle Image Velocimetry System in the NASA GRC 225 cm2 Wind Tunnel

As part of an ongoing campaign to provide detailed and thorough measurements in a two-dimensional impinging shock-wave/boundary-layer interaction (SWBLI), a custom implementation of the Particle Image Velocimetry (PIV) measurement technique in the NASA Glenn 225 cm2 Wind Tunnel was constructed. The flow seeding apparatus was devised to locally seed the region of interest in the overall flowfield to avoid coating the viewing window with seed material. The ability of the PIV system to provide small particles which faithfully track the underlying gas-phase flowfield was of key importance for the success of this system to make quality measurements in the SWBLI flowfield. In order to optimize and assess the performance of the particle seeding system, PIV measurements were made across a planar oblique shock wave and particle response was analyzed to quantify the particle lag effects due to the finite inertia of the seed droplets. Video recordings from a camera placed in the wind tunnel plenum tank were also used to discern the near-field behavior of the seeded plume and guide the design evolution of the seeding apparatus. The resulting optimized seeding configuration was applied to make PIV measurements in the wind tunnel test section boundary layer to assess the seed particle spatial coverage and concentration. This sample boundary layer dataset provides an analog to the eventual boundary layer measurements to be made in the axisymmetric test section under much more challenged viewing conditions.

PIV↗
NASA NTRS1950

Investigation of Operating Pressure Ratio of a Supersonic Wind Tunnel Utilizing Distributed Boundary-layer Suction in Test Section

Effect of distributed boundary-layer suction on operating pressure ratio of a supersonic wind tunnel was investigated. Investigation was made in 3.84- by 10-inch supersonic tunnel operating at Mach number 2.0 and suction was applied in neighborhood of the normal shock to two walls of a constant-area extension of test section. A reduction of 4 percent of operating pressure ratio was attributed to improved flow conditions at subsonic-diffuser inlet. The theoretical normal shock was, in practice, replaced by a multiple-branch shock configuration across which the flow parameters changed in approximate accordance with the Rankine-Hugoniot values.

Cohen, C B↗
NASA NTRS1989

Flowfield measurements in the NASA Lewis Research Center 9- by 15-foot low-speed wind tunnel

An experimental investigation was conducted in the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel to determine the flow characteristics in the test section during wind tunnel operation. In the investigation, a 20-probe horizontally-mounted Pitot-static flow survey rake was used to obtain cross-sectional total and static pressure surveys at four axial locations in the test section. At each axial location, the cross-sectional flowfield surveys were made by repositioning the Pitot-static flow survey rake vertically. In addition, a calibration of the new wind tunnel rake instrumentation, used to determine the wind tunnel operating conditions, was performed. Boundary laser surveys were made at three axial locations in the test section. The investigation was conducted at tunnel Mach numbers 0.20, 0.15, 0.10, and 0.05. The test section profile results from the investigation indicate that fairly uniform total pressure profiles (outside the test section boundary layer) and fairly uniform static pressure and Mach number profiles (away from the test section walls and downstream of the test section entrance) exist throughout in the wind tunnel test section.

Hughes, Christopher E.↗
NASA NTRS1971

The NASA Quiet Engine Programme.

Discussion of the experimental Quiet Engine developed under the NASA program to reduce jet aircraft noise levels. The current status of the program is given as follows: Aerodynamic evaluation of the three fans is complete and their acoustic evaluation is partially complete. Tests of fan casing boundary-layer section and of serrated leading edges on the half-scale B fan are complete and are underway on the half-scale C fan. Tests of the first engine with the A fan began in August 1971.

Kramer, J. J.↗
NASA NTRS1974

Noise reduction in transonic wind tunnels

The phenomena of background noise generation in transonic wind tunnels are analyzed. In unsteady aerodynamic tests, background disturbances create problems because the instrumentation senses them in addition to the fluctuations generated by the aerodynamic flow over wind-tunnel models. Calibrations of 25 facilities show that the amplitudes of the background fluctuations are excessive. In porous-wall facilities, one noise source consists of porous-wall edgetones that are generated by the passage of air over the holes. A flow model is developed that yields the frequencies of these oscillations. Test section boundary layers and hole configurations govern the occurrence of these fluctuations. In slotted-wall facilities, a noise source is the slotted-wall shearing caused by the air flowing along the openings. In both types of wind tunnels, other flow mechanisms also cause disturbances, and these phenomena are described. Noise-reduction methods are outlined which will provide valid unsteady aerodynamic results.

Mccanless, G. F., Jr.↗
NASA NTRS1981

Description and calibration of the Langley unitary plan wind tunnel

The two test sections of the Langley Unitary Plan Wind Tunnel were calibrated over the operating Mach number range from 1.47 to 4.63. The results of the calibration are presented along with a a description of the facility and its operational capability. The calibrations include Mach number and flow angularity distributions in both test sections at selected Mach numbers and tunnel stagnation pressures. Calibration data are also presented on turbulence, test-section boundary layer characteristics, moisture effects, blockage, and stagnation-temperature distributions. The facility is described in detail including dimensions and capacities where appropriate, and example of special test capabilities are presented. The operating parameters are fully defined and the power consumption characteristics are discussed.

Jackson, C. M., Jr.↗
NASA NTRS1996

Loss Mechanisms and Unsteady Flows in Turbomachines

The Conference Proceedings contains 42 papers presented at the Propulsion and Energetics Panel 85th Symposium on Loss Mechanisms and Unsteady Flows in Turbomachines which was held from 8-12 May 1995, in Derby, UK. Sessions: Cascade Steady Flow Mechanisms and Losses (9 papers); Steady Flow Clearance and Injection Flow Mechanisms and Losses (6); Steady Secondary Flows and Shock Boundary Layer Interaction (3); Blade Section-Wake Boundary layer Interaction (6); Management of Unsteady Flows (10); Blade Interactions (8). The Symposium contributes to improving the efficiency and operation of turbomachinery also in off-design conditions by application of experimental and computational fluid dynamics methods. Multi-stage methods and positive loss management in the design stage have been identified as next steps. This will yield optimized engines of high efficiency for expanded flight envelopes including active control of the plane movement at high reliability levels.

Advisory Group for Aerospace Research and Developm↗
NASA NTRS1988

Sidewall boundary-layer measurements with upstream suction in the Langley 0.3-meter transonic cryogenic tunnel

The Langley 0.3 Meter Transonic Cryogenic Tunnel has provision for boundary removal from the sidewalls to reduce sidewall interference effects on the test data. The tests carried out to determine the change in the empty test section sidewall boundary layer thickness at the model station with upstream boundary layer mass removal are described. The boundary layer measurements showed that the upstream removal region is effective in reducing the boundary layer thickness at the model station. The boundary layer displacement thickness reduced from about 1.2 percent to about .4 percent of the test section width. The boundary layer velocity profiles followed a power law variation in the outer region and showed good correlation when plotted in terms of boundary layer momentum thickness.

Murthy, A. V.↗
NASA NTRS1972

An experimental investigation of turbulent boundary layers along curved surfaces

A curved wall tunnel was designed, and an equilibrium turbulent boundary layer was set up on the straight section preceding the curved test section. Turbulent boundary layer flows with uniform and adverse pressure distributions along convex and concave walls were investigated. Hot-wire measurements along the convex surface indicated that turbulent mixing between fluid layers was very much reduced. However, the law of the wall held and the skin friction, thus determined, correlated well with other measurements. Hot-wire measurements along the concave test wall revealed a system of longitudinal vortices inside the boundary layer and confirmed that concave curvature enhances mixing. A self-consistent set of turbulent boundary layer equations for flows along curved surfaces was derived together with a modified eddy viscosity. Solution of these equations together with the modified eddy viscosity gave results that correlated well with the present data on flows along the convex surface with arbitrary pressure distribution. However, it could only be used to predict the mean characteristics of the flow along concave walls because of the existence of the system of longitudinal vortices inside the boundary layer.

So, R. M. C.↗