Search NASA⌕ Search

SEARCH · Search NASA

Results for “BPVC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

UNDERSTANDING THE SEMI-PROBABILISTIC APPROACHES IN STRUCTURAL RELIABILITY USED TO SET DESIGN RELIABILITY TARGETS FOR GRAPHITE COMPONENTS USING ASME BPVC METHODS

Graphite is a quasi-brittle material, resulting in random variability in tensile strength distributions. To account for the random variability in strength, HHA-3000 of the ASME BPVC provides two semi-probabilistic methods for qualifying nuclear graphite components in the design stage, the simplified and full assessments. The full and simplified assessments apply statistical methods to engineering-based design problems. This is often referred to as reliability-based design. Reliability-based design (RBD) is a method to develop reliable designs by accounting for uncertainties and result in small chances of failure when also considering safety factors. RBDs provide reliability targets using semi-probabilistic approaches. RBD is implemented in ASME BPVC HHA-3000 for nuclear graphite components, but is not specific to that application. There has been much confusion around the methods implemented in ASME BPVC HHA-3000 for qualifying nuclear graphite components. To address the confusion, this paper takes a hierarchical approach. First, the general RBD framework is presented. Then, the semi-probabilistic methods and the underlying assumptions implemented in the assessments are presented. The semi-probabilistic methods are separated from the engineering modifications that have been made to the assessments. After building the framework and underlying assumptions, the specific methods in the full and simplified assessments are explained in three steps: inputs, methods, outputs. The methods are applied to an H-451 reflector block. Tensile strength properties for other graphite grades are provided.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

ECAR-8446 Rev 0 MARVEL BPVC Section III Division 5 HBB Fatigue Acceptance Tests

The objective of this analysis is to evaluate the fatigue and creep behavior of 316 SS materials used in the Primary Coolant System (PCS) and Guard Vessel System (GVS) for the first two years of MARVEL reactor operation. The analysis follows the requirements set forth in ASME BPVC Section III, Division 5, HBB-2800, which mandates a fatigue test if operational conditions exceed allowable thresholds. By determining whether the materials meet the HBB-T-1324(a) and HBB-T-1324(b) criteria, this evaluation establishes whether a fatigue test is necessary, as well as the maximum allowable operational hours and temperatures before fatigue testing would be required. The deliverables of this analysis include calculations validating compliance with fatigue acceptance criteria, determination of maximum operational limits for the two-year period, and identification of conditions under which a fatigue test would be necessary. This ensures that the PCS and GVS can operate safely without premature material degradation and align with the design life requirements outlined in SPC-70731. Additionally, this evaluation provides conservative estimates for Service Level B occurrences and their impact on allowable Service Level A hours and temperatures, offering guidance for future operational assessments and potential life extensions beyond the initial two-year period.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
DOE OSTI2024

SPC-70731 Rev 0 MARVEL Reactor Project ASME BPVC Section III Division 5 Design Specification

This specification establishes the requirements for the design of the MARVEL Primary Coolant System (PCS) Boundary, Guard Vessel System (GVS) Boundary, Core Support Structure (CSS), and Internal Heat Exchanger (IHX) Liner to provide a complete basis for ASME BPVC Section III Division 5 construction. All information in this section is generic and applicable to all metallic components unless otherwise specified.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
DOE OSTI2024

Application of C ( t )-Integral Solutions in Extending ASME BPVC Section XI Division 2 Code Case N-934 for Transient Creep Crack Growth

Creep crack growth is a phenomenon which arises in damaged metallic structures under combined primary and secondary loads in the creep regime. The High Temperature Flaw Evaluation Code Committee of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code (BPVC) is evaluating methods in extending Code Case N-934 to capture transient creep crack growth. Here, this paper provides context and basic examples on the selected approach to transient creep crack growth methods based on the C(t)-integral. The basis for selected C(t)-integral solution as analytical method is established, including an overview of its derivation. Practical assessments of a crack growing under creep conditions in a realistic component are conducted to illustrate the analytical approach. Additional considerations in the application of the analytical methods and limitations are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

ECAR-6564 MARVEL Project Primary Coolant System ASME BPVC Section III Division 5 Design by Analysis

This report demonstrates that the MARVEL Reactor Primary Coolant Boundary (herein referred to as the Primary Coolant System, or PCS) is designed to meet ASME BPVC Section III Division 5 elevated temperature service design-by-analysis criteria. The analysis approach that delineates division of responsibilities to meet project objectives is discussed herein. In short, Design and Service Level A, B, and C code calculations are detailed in ECAR-6580 for the majority of the PCS with complex geometry, while the Lower Downcomers, Bottom Head, and Reactor Core Barrel are analyzed in ANL-23/56. Service Level D code calculations are detailed in this document.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Recommendation for Limiting Conditions for ASME BPVC Section III Division 5 Allowable Stress Criteria

Section III, Division 5 of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC) specifies rules for elevated temperature nuclear reactors. Time dependent allowable stresses are an important aspect of the high temperature design models and are related to the time to 1% strain, time to rupture, and time to onset of tertiary creep. The time to onset of tertiary creep criterion has an overly strong negative influence on the allowable stresses for some structural materials, likely due to very limited datasets and misidentification of microstructural changes rather than onset of significant creep damage, as tertiary creep is meant to represent. It is recommended that the onset of tertiary creep be determined through an alloy specific ratio between onset of tertiary creep and creep rupture time, which would give access to the significantly larger creep rupture time datasets.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

ECAR-6564 Rev 1 MARVEL Project Primary Coolant System ASME BPVC Section III Division 5 Design by Analysis

This report demonstrates that the MARVEL Reactor Primary Coolant Boundary (herein referred to as the Primary Coolant System, or PCS) is designed to meet ASME BPVC Section III Division 5 elevated temperature service design-by-analysis criteria. The analysis approach that delineates division of responsibilities to meet project objectives is discussed herein. In short, Design and Service Level A, B, and C code calculations are detailed in ECAR-6580 [9] for the majority of the PCS with complex geometry, while the Lower Downcomers, Bottom Head, and Reactor Core Barrel are analyzed in ANL-24/36. Service Level D code calculations are detailed in this document.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
DOE OSTI2022

ASME BPVC Section III Division 5 Application

Using AMSE assessments Simplified assessment overview Implementation Limitation and important considerations Example problems Full Assessment overview Implementation Limitation and important considerations Example problems Limitation of the code

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

RIM: Reliability and Integrity Management/ASME BPVC Section XI Division 2

Prepared at the request of the Nuclear Energy Institute (NEI) and the Joint Committee on Nuclear Risk Management's SubCommittee on Risk Applications, this slide set presents an update on some recent Reliability and Integrity Management (RIM) Subgroup work to respond to industry questions on American Society of Mechanical Engineers Boiler and Pressure Vessel Code Section XI Division 2. If approved, the briefing will be given at an upcoming workshop of the Nuclear Energy Institute (February 18-20, Washington, DC) and at an upcoming meeting of the Joint Committee on Nuclear Risk Management's SubCommittee on Risk Applications (February 25-26, College Park, MD).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Thermal Aging Effects on the Yield and Tensile Strength of 9Cr-1Mo-V (Grade 91)

The long-term exposure of 9Cr-1Mo-V (Grade 91) steel to elevated temperature can have a significant effect on reducing its yield and tensile strength. The yield and tensile strength changes, in turn, have potential implications to the assurance of the integrity of components constructed with this material over their design or intended lifetime. The ASME Boiler & Pressure Vessel Code (BPVC), Section III, Division 5 (III-5, high temperature reactors) provides tabulated reduction factors for Grade 91 yield and tensile strength as a function of exposure temperature and time up to 300,000 h. ASME BPVC III-5 s intent to extend these factors to an exposure duration of 500,000 h, the lack of available historic information to support the existing factors, and the recent development of a physics-based prediction model for ASME BPVC application are prime motivation for this study. This work describes results of the conventional time-temperature Hollomon–Jaffe parameter, strength reduction ratio prediction method using an updated, extensive Grade 91 unaged and related aged material strength database. The method, previously used by Oak Ridge National Laboratory in its evaluation of Grade 91 and likely used in development of the existing BPVC III-5 reduction factors, provides strength reduction ratio predictions useful for general component fitness-for-service assessments and for computing BPVC III-5 reduction factors as defined. Specific reduction factors to 500,000 h at 650 °C applicable to ASME BPVC III-5 are computed from the strength reduction ratios.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Initial Assessment of Erosion/Abrasion Issues Related to Gas-Cooled Reactors

The US Department of Energy’s Oak Ridge National Laboratory (ORNL) is investigating the graphite erosion concern detailed in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC), Section III, Division 5, “High Temperature Reactors.” The special consideration in Subsection HH, Subpart A (HHA)-3143, “Abrasion and Erosion,” was described in ASME BPVC Section III, Division 5, which was accepted with exception/limitation in a US Nuclear Regulatory Commission (NRC) Technical Review. This report describes ORNL’s FY 2023 comprehensive research of erosion-related reports and publications to further study the proposed gas flow velocity limitation to the erosion effect in graphite structure in the ASME BPVC. This report also proposes that a nondimensional fluid parameter, the Reynolds number, might be a better alternative than gas flow velocity for comparing erosion effects caused by carbonaceous dust in fast-flowing helium coolant in gas-cooled reactors (GCRs).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Graphite Licensing (ASME) and Testing (ASTM) Technical Assistance

DOE ART Graphite R&D program is currently involved in developing the structural code for licensing the new High Temperature Reactor (HTR) designs through the ASME Boiler Pressure Vessel Code (BPVC). The basic structural design code for graphite core components has been written, approved, and within the BPVC since 2012. However, several areas within the graphite code remain to be improved, specifically the addition of material property changes resulting from environmental degradation (neutron flux and oxidation). The incorporation of this data, which can significantly affect the graphite components and alter the structural integrity of the core during operation, is proving to be an important activity. How this data will be incorporated within the code and how it will be used for license applications will be critical to a number of HTR applicants in the future. These modifications to the code must take into account the unique irradiation and oxidation response of the wide spectrum of available nuclear graphite grades currently under consideration for HTR applications. Additionally, the ASME BPVC requires material property testing within the expected operational conditions of the HTR core including neutron radiation flux, elevated temperatures, and after chronic/acute oxidation of the graphite components. Currently, no standardized graphite testing methods are approved for these environmental conditions. New American Society for Testing and Materials (ASTM) standardized tests for elevated temperature testing, small sample testing, and testing after oxidation must be developed to support the requirements within the ASME code.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Machining of Alloy 709 Creep-fatigue Specimens from G. O. Carlson Heat

Alloy 709 has been selected as the next candidate material for Section III, Division 5 qualification in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC) for elevated-temperature nuclear construction. The qualification data package requires an assortment of information and material data including tensile, creep, and creep-fatigue performance at elevated temperatures from different material heats. The goal of the project is to generate a dataset to support qualification of Alloy 709 material for ASME BPVC design code. Working towards the project goal, Idaho National Laboratory needs to conduct a series of tests on three different heats to support the A709 code case development. At present, there is a gap in the data package for one of the heats: Heat number 58776 manufactured by G.O. Carlson. To address this data gap, Argonne National Laboratory transmitted five plates of A709 heat 58776 manufactured by G.O. Carlson to Idaho National Laboratory. These plates were solution annealed at 1150°C and heat treated at 775°C for 10 hours. The objective of this specification is to procure a series of creep-fatigue specimens to support the qualification data package. The creep-fatigue specimen design captures the cyclic material performance at elevated temperature. The material performance data generated from specimens machined herein will support the ASME BPVC code case development and establish design limits, and design life curves for Alloy 709 material.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

FY25 status report on the addition of candidate materials in Class B Code Case

This report provides the time-dependent allowable stress calculation strategy leveraging the limited creep rupture tests data generated to support the allowable stress for 100,000 hours in American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC), Section II, Part D. A variable confidence index procedure to extrapolate material properties to support 500,000 hours design life is discussed. Time-dependent allowable stresses for Class B component design and analysis are presented for Grade 1 and Grade 2 of Alloy 625. The presented data extrapolation and allowable stress calculation method will support new material addition using limited creep rupture data in the new ASME Boiler and BPVC, Section III, Division 5, Class B rules.

Part D↗
DOE OSTI2025

Alloy 625 Qualification Pathway for ASME Section III Division 5 Class A construction

The American Society of Mechanical Engineers Boiler and Pressure Vessel Code Section III Division 5 provides construction and inspection rules to ensure the safety of nuclear components operating at elevated temperatures, defined as those operating above 700°F (370°C) or 800°F (425°C), depending on the material type. At present, there are six materials approved for Class A (high safety significance) component construction under ASME BPVC Section III Division 5. Out of these six materials, five materials are steels or iron-based alloys and one material, Alloy 617, is a nickel alloy. Nickel alloys are stronger than steels; however, Alloy 617 consists of 10-15% cobalt, and activation is a concern under irradiation. Therefore, there is a need to qualify new nickel alloy with lower cobalt content. Alloy 625 is one candidate which has similar mechanical properties at elevated temperature compared to Alloy 617 and has a maximum of 1% cobalt. Although Alloy 625 material properties have been developed in the past to support allowable stress development under ASME Section II, new test results would be needed to qualify this material for elevated temperature component construction under ASME Section III Division 5. The purpose of this report is to describe a path towards developing a Nuclear Code Case to qualify Alloy 625 (UNS N06625; Grade 1 and Grade 2) for elevated temperature nuclear use in accordance with the ASME BPVC rules. This report reviews the existing database on Alloy 625, presents proposed test campaign, and discusses potential paths for accelerating the accelerated material qualification process.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

ASME Code Development: Design Rules

ASME Code Development: Design Rules, ASME BPVC, and ASME BPVC HHA-3000, Design Task Group Papers, Presentations, and Memorandums, and records.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

ASME Design Code Rule Changes for Nuclear Graphite

The American Society of Mechanical Engineers Boiler Pressure and Vessel Code (ASME BPVC) Section III, Division 5, Article HHA-3000 outlines graphite core component and graphite core assembly design guidelines. Graphite core components are defined as ?components manufactured from graphite that are installed to form a graphite core assembly within the reactor pressure vessel of a high temperature, graphite moderated fission reactor.? (p. 413) Graphites? inherent defect distributions do not allow for deterministic material reliability. Rather, graphite has variable strength distributions which change by grade. Article HHA-3000 outlines two semi-probabilistic methods, the full and simplified assessments, which set design load limit targets for each of three component structural reliability classes. The Design Task Group was officially recognized as a specialized task group within ASME November of 2023, though we?ve been collaborating since 2022. The purpose of the Design Task Group is to correct, clarify, and make HHA-3000 function as intended. The Design Task Group will sunset once we?ve achieved our objectives. The Design Task Group was specifically told to not write new Code. While there may be more precise and more accurate methods to determine reliability targets, the current methods are conservative, relatively simple to implement, and have thus far been considered satisfactory for setting design reliability targets. Much of the ground-work to write proposal files and background documents for records to make the changes needed to achieve our objective have been completed. The Design Task Group has documented much of their work through papers, presentations, and memorandums. Three memorandums in which INL team members had substantial contributions are found in the Appendices: FEA Modeling for the Baseline Program, Evaluating the Effects on Margin of Updating the Threshold and Shape Parameters in the Full Assessment, and Interpretations of the Full and Simplified Assessments in ASME BPVC. Most of the on-going work to achieve the Design Task Group?s objective will be addressing comments on existing records and moving records through the balloting process. The Design Task Group met bi-weekly mostly through the end of FY2023. Since February 2024, the Design Task Group has mostly been completed with solving and documenting the technical issues associated with the assessments. Unless new tasks are identified, the remaining work of the Design Task Group will be political and editorial.

97 MATHEMATICS AND COMPUTING↗