Search NASA⌕ Search

SEARCH · Search NASA

Results for “BRONZE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Upper limit for magnetoresistance in silicon bronze and phosphor bronze wire

The electrical resistivity of silicon bronze and phosphor bronze was measured in magnetic fields from 0 to 14 T and at temperatures between 2 and 300 K. At any fixed temperature, the change in resistivity to 14 T was less than a few parts in 100,000. Thus, these bronzes are excellent for use in high magnetic fields where constant resistance is required. Welding leads to the sample was found to be superior to soldering. The soldered contacts were subject to spurious resistivity changes that resulted from superconducting transitions in the solder.

Feldman, R.↗
DOE OSTI2021

Rapid Nb 3 Sn film growth by sputtering Nb on hot bronze

Nb deposited by magnetron sputtering onto hot Cu-15 wt.%Sn bronze substrates at temperatures above 700 °C achieved Nb 3 Sn film growth at a rate of 33 nm min -1 , which was an order of magnitude faster than that achieved for deposition of Nb on bronze at low temperature followed by in situ post reaction at the same high temperatures. Tin content in the Nb 3 Sn films made on hot bronze was ~26.3%, which is significantly higher than ~24.5% obtained by post-reaction as well as for typical bulk reactions between Nb and α -bronze. The Nb 3 Sn lattice parameter was consistent with measured tin content and predicted elastic strain for both routes. Critical temperatures of 14 K–16 K, instead of 18 K, were consistent with elastic strain due to coefficient of thermal expansion mismatch between the Nb 3 Sn and bronze substrate and, for the hot-bronze samples, stress related to the growth mechanism. Films were fully coalesced and had surface roughness values <20 nm over a 100 μ m 2 scan. Grain structure of the Nb 3 Sn films produced by Nb sputtering on hot bronze resembles zone 2 in the Thornton structure-zone diagram, in contrast to the equiaxed grain structure reminiscent of microstructure observed in reacted Nb 3 Sn wires exhibited by the post-reaction route.

Physics↗
DOE OSTI2024

Solution-Phase Synthesis of Platinum-Decorated Hydrogen Tungsten Bronzes for Hydrogen Atom Transfer from Oxides to Molecules

Hydrogen bronzes can be used as hydrogen donors for the broad class of reactions involving proton-coupled electron transfer (PCET). Here, in this work, we describe a method to prepare platinum-decorated hydrogen tungsten bronzes, Pt@H x WO 3 · n H 2 O with n = 0, 1, and 2, by reacting the pristine oxides at modest temperatures with a mild reducing agent, H 3 PO 2 , and H 2 PtCl 6 in an aqueous solution. We explored the tunability and kinetics of this reaction and compared it with that of archetypal gas–solid hydrogen spillover. We demonstrate that the identity of the noble metal affects the extent of bronze reduction. This suggests that the mechanism proceeds via the adsorption of a hydrogen-atom species on the noble metal. Finally, we explored the ability of the Pt-decorated hydrogen tungsten bronzes to hydrogenate a model H + /e – acceptor, 2,2,6,6-tetramethyl-1-piperidinyloxyl (TEMPO). The bronze phases return to their fully oxidized states along with the subsequent reduction of TEMPO to TEMPOH. Overall, this work demonstrates a solution-phase method to obtain hydrogen bronzes, which can then be used to perform hydrogen transfer reactions, providing a pathway for the use of extended transition metal oxides as stoichiometric reagents for broad classes of hydrogenation reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1974

Preparation and evaluation of thin-film sodium tungsten bronzes

Thin films of sodium tungsten bronze (NaxWO3) were investigated as reversible sodium ion electrodes for solid electrolytes. The films were made by electron beam evaporation of the three phases, W metal, Na2WO4, and WO3, followed by sintering. The substrates were sodium beta alumina disks and glass slides. X-ray diffraction analyses of the films showed that sintering in dry nitrogen with prior exposure to air lead to mixed phases. Sintering in vacuum with no air exposure produced tetragonal I bronze with a nominal composition of Na0.31WO3, single phase within the limits of X-ray diffraction detectability. The films were uniform and adherent on sodium beta alumina substrates. The ac and dc conductivities of the beta alumina were measured with the sodium tungsten bronze films as electrodes. These experiments indicated that the tetragonal I bronze electrodes were not completely reversible. This may have resulted from sodium ion blocking within the bronze film or at the bronze beta alumina interface. Methods for attempting to make more completely reversible electrodes are suggested.

Kautz, H. E.↗
NASA NTRS2009

Thermal and Electrical Conductivity Measurements of CDA 510 Phosphor Bronze

Many cryogenic systems use electrical cables containing phosphor bronze wire. While phosphor bronze's electrical and thermal conductivity values have been published, there is significant variation among different phosphor bronze formulations. The James Webb Space Telescope (JWST) will use several phosphor bronze wire harnesses containing a specific formulation (CDA 510, annealed temper). The heat conducted into the JWST instrument stage is dominated by these harnesses, and approximately half of the harness conductance is due to the phosphor bronze wires. Since the JWST radiators are expected to just keep the instruments at their operating temperature with limited cooling margin, it is important to know the thermal conductivity of the actual alloy being used. We describe an experiment which measured the electrical and thermal conductivity of this material between 4 and 295 Kelvin.

Tuttle, James E.↗
DOE OSTI2023

Structure and Electrochemical Properties of Bronze Phase Materials Containing Two Transition Metals

Bronze phase transition-metal oxides have recently attracted attention as high-rate lithium-ion battery anode materials. Their crystal structures are distinguished by large tunnels and an open framework, facilitating lithium-ion diffusion and high-rate charge–discharge properties. The presence of two transition metals also offers a route to achieve high energy density from multielectron redox. In this paper, we report the chemistry, structure, and electrochemical properties of two different bronze phase compositions having the same stoichiometry: W 3 Nb 2 O 14 and Mo 3 Nb 2 O 14 . These materials provide insight into how the transition metals affect the electrochemical behavior and structural stability of bronze phase materials. Mo 3 Nb 2 O 14 exhibits greater than 1 electron redox per transition metal leading to lithium capacities above 200 mAh g –1 at C/2 but is unable to maintain this high capacity at high rates due to incomplete Mo redox reactions. In contrast, W 3 Nb 2 O14 exhibits reversible redox reactions and retains its open structure on cycling. This study highlights the potential of bronze phase materials containing two transition metals to exhibit fast charging properties with a high energy density.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Operando pair distribution function analysis of nanocrystalline functional materials: the case of TiO 2 -bronze nanocrystals in Li-ion battery electrodes

Structural modelling of operando pair distribution function (PDF) data of complex functional materials can be highly challenging. To aid the understanding of complex operando PDF data, this article demonstrates a toolbox for PDF analysis. The tools include denoising using principal component analysis together with the structureMining , similarityMapping and nmfMapping apps available through the online service `PDF in the cloud' ( PDFitc , https://pdfitc.org/). The toolbox is used for both ex situ and operando PDF data for 3 nm TiO 2 -bronze nanocrystals, which function as the active electrode material in a Li-ion battery. The tools enable structural modelling of the ex situ and operando PDF data, revealing two pristine TiO 2 phases (bronze and anatase) and two lithiated Li x TiO 2 phases (lithiated versions of bronze and anatase), and the phase evolution during galvanostatic cycling is characterized.

Chemistry↗
NASA NTRS1979

Properties and performance of fine-filament bronze-process Nb3Sn conductors

Fine-filament bronze-process Nb3Sn superconductors were fabricated to fulfill stringent requirements on critical current under tension in a one-inch bend diameter, current density, stability, and conductor losses. A large fraction of niobium filaments was incorporated in a bronze matrix, and a cable containing 4453 2-micron diameter filaments in each of six strands provided a current density of 85,000 A/sq cm at 10 to the -11th ohm-cm, 10 T, and 4.2 K. The next step was to incorporate copper stabilizer in a conductor with 20,538 filaments. These conductors, fabricated so that bend strains of about 1% would be experienced by the filaments in the one-inch bend, stably carried currents in the 200-500 A range. A quench current of 540 A in a 5-cm bend corresponds to 158,000 A/sq cm in the bronze and filament area, believed to be the highest critical current density reported for multifilamentary Nb3Sn.

Walker, M. S.↗
DOE OSTI2025

On the Structural Origin of Fast Li-Ion Cycling in Tetragonal Bronze-Type Nb 8 W 9 O 47

Bronze and bronze-derived, mixed metal oxides are materials of growing interest for lithium-ion battery anodes due to their high-rate capabilities and the potential for high energy densities via multielectron redox. We report on the synthesis and electrochemical properties of the tetragonal tungsten bronzetype phase Nb 8 W 9 O 47 and our investigation into the structural evolution of this phase upon lithium (de)intercalation, with particular attention to how it relates to the fast-cycling capabilities. Electrochemical cycling shows Nb 8 W 9 O 47 can achieve greater than one Li + per transition metal at rates of C/2 or slower and maintains a capacity equivalent to 0.65 Li + per transition metal at a rate of 20C. Sequential Rietveld analysis of operando X-ray diffraction data reveals anisotropic changes to the unit cell parameters during discharge, accompanied by an off-centering of the transition metals within their octahedral environments. While higher capacities can be accessed below 1.2 V, cells discharged to 1.0 V exhibit a significant expansion of the unit cell volume and reduced Coulombic efficiencies. This report suggests that rigid crystal structures incapable of undergoing polyhedral rotational deformations can instead exploit displacive distortions of the transition metal redox center to enable fast Li-ion cycling with minimal atomic rearrangements.

25 ENERGY STORAGE↗
DOE OSTI2020

Probing Mg Intercalation in the Tetragonal Tungsten Bronze Framework V 4 Nb 18 O 55

While commercial Li-ion batteries offer the highest energy densities of current rechargeable battery technologies, their energy storage limit has almost been achieved. Therefore, there is considerable interest in Mg batteries, which could offer increased energy densities in comparison to Li-ion batteries if a high-voltage electrode material, such as a transition-metal oxide, can be developed. However, there are currently very few oxide materials which have demonstrated reversible and efficient Mg 2+ insertion and extraction at high voltages; this is thought to be due to poor Mg 2+ diffusion kinetics within the oxide structural framework. Here, in this paper, the authors provide conclusive evidence of electrochemical insertion of Mg 2+ into the tetragonal tungsten bronze V 4 Nb 18 O 55 , with a maximum reversible electrochemical capacity of 75 mA h g –1 , which corresponds to a magnesiated composition of Mg 4 V 4 Nb 18 O 55 . Experimental electrochemical magnesiation/demagnesiation revealed a large voltage hysteresis with charge/discharge (1.12 V vs Mg/Mg 2+ ); when magnesiation is limited to a composition of Mg 2 V 4 Nb 18 O 55 , this hysteresis can be reduced to only 0.5 V. Hybrid-exchange density functional theory (DFT) calculations suggest that a limited number of Mg sites are accessible via low-energy diffusion pathways, but that larger kinetic barriers need to be overcome to access the entire structure. The reversible Mg 2+ intercalation involved concurrent V and Nb redox activity and changes in crystal structure, as confirmed by an array of complementary methods, including powder X-ray diffraction, X-ray absorption spectroscopy, and energy-dispersive X-ray spectroscopy. Consequently, it can be concluded that the tetragonal tungsten bronzes show promise as intercalation electrode materials for Mg batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1973

Influence of various surface pretreatments on adherence of sputtered molybdenum disulfide to silver, gold, copper, and bronze

Solid film lubricants of radio frequency sputtered molybdenum disulfide (MoS2) were applied to silver, gold, copper, and bronze surfaces that had various pretreatments (mechanical polishing, sputter etching, oxidation, and sulfurization). Optical and electron transmission micrographs and electron diffraction patterns were used to interpret the film formation characteristics and to evaluate the sputtering conditions in regard to the film and substrate compatibility. Sputtered MoS2 films flaked and peeled on silver, copper, and bronze surfaces except when the surfaces had been specially oxidized. The flaking and peeling was a result of sulfide compound formation and the corresponding grain growth of the sulfide film. Sputtered MoS2 films showed no peeling and flaking on gold surfaces regardless of surface pretreatment.

Spalvins, T.↗
DOE OSTI2020

Sn 0.24 WO 3 hexagonal tungsten bronze prepared via the metal chloride route

In this work, we report the synthesis of Sn 0.24 WO 3 single crystals via an alternative, less well-known, solid-state synthetic approach that involves the use of tin chloride as a starting material. The compound adopts an unusual variant of the hexagonal tungsten bronze structure in space group P6/mmm (a = 7.4264(7) Å and c = 3.7843(4) Å) with a previously unreported distribution of Sn cations, disordered over two distinct sites in the tunnels. Sn 0.24 WO 3 shows no signs of superconductivity down to 170 mK and exhibits weakly-metallic conducting behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Water-Pillared Sodium Vanadium Bronze Nanowires for Enhanced Rechargeable Magnesium Ion Storage

Owing to the advantages of high safety, low cost, high theoretical volumetric capacities, and environmental friendliness, magnesium-ion batteries (MIBs) have more feasibility for large-scale energy storage compared to lithium-ion batteries. However, lack of suitable cathode materials due to sluggish kinetics of magnesium ion is one of the biggest challenges. Herein, water-pillared sodium vanadium bronze nanowires (Na 2 V 6 O 16 ·1.63H 2 O) are reported as cathode material for MIBs, which display high performance in magnesium storage. The hydrated sodium ions provide excellent structural stability. The charge shielding effect of lattice water enables fast Mg 2+ diffusion. It exhibits high specific capacity of 175 mAh g -1 , long cycle life (450 cycles), and high coulombic efficiency (≈100%). At high current density of 200 mA g -1 , the capacity retention is up to 71% even after 450 cycles (compared to the highest capacity), demonstrating excellent long-term cycling performance. The nature of charge storage kinetics is explored. Furthermore, a highly reversible structure change during the electrochemical process is proved by comprehensive electrochemical analysis. The remarkable electrochemical performance makes Na 2 V 6 O 16 ·1.63H 2 O a promising cathode material for low-cost and safe MIBs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The hydrogen-containing bronzes H 0.23 WO 3 and H 0.10 ReO 3 synthesized via a polymer route

We report the synthesis of two hydrogen-containing perovskite-type bronzes H 0.23 WO 3 and H 0.10 ReO 3 utilizing an unconventional solid-state synthetic approach, involving the use of the polymer Poly(vinylidene fluoride) (CH 2 CF 2 ) n. Powder neutron diffraction at ambient temperature shows that H 0.23 WO 3 crystallizes in a tetragonal symmetry distortion of the simple perovskite structure (space group P4/nmm), with lattice parameters a = 5.2279(2) Å, and c =3.8763(1) Å. H 0.10 ReO 3 , in contrast, crystallizes in a monoclinic distortion of a simple cubic perovskite (space group P2/m), with lattice parameters a = 5.3125(1) Å, b = 5.3155(3) Å, c = 3.7045(3) Å, and γ = 90.43(1)°. Both H 0.23 WO 3 and H 0.10 ReO 3 exhibit intrinsically diamagnetic behavior, with low temperature paramagnetic upturns and no signs of bulk superconductivity down to 0.35 K.

36 MATERIALS SCIENCE↗
DOE OSTI2026

The incommensurate modulation of tetragonal tungsten bronze quantified by high resolution 4D STEM

Many members of the tetragonal tungsten bronze (TTB) family of oxides display an incommensurate periodic lattice distortion, the nature of which has been the subject of some controversy. Here we present a study of this structural modulation in the relaxor ferroelectric Ba 5 SmSn 3 Nb 7 O 30 (BSSN) by quantitative scanning transmission electron microscopy (STEM). Additionally, we characterize the modulation in BSSN by employing a fast, pixelated direct electron detector to perform high resolution phase contrast STEM imaging of the crystalline lattice. By quantitatively analyzing the images, we visualize the atomic structural correlations present in the material on both the cation and anion sublattices. This analysis reveals the incommensurate structure to have an octahedral tilting pattern and cooperative A2 site cation displacements, analogous to an Ama2 commensurate cell. Finally, we show that the modulation is composed of a structural motif with a period of 3 x $d_{1\bar{1}0}$ and modified by discommensurations, likely arise from frustrated octahedral tilting in the odd-valued periodicity.

Differential phase contrast↗
DOE OSTI2021

Investigations Towards Ultra-Low Cost Nb 3 Sn SRF Fabrication via Melt Casted Bronze Route Processing

Here, a novel approach to fabricating Nb 3 Sn SRF cavities and other RF components using an ultra-low-cost melt casting fabrication process has been investigated. This simple, low cost melt casting technique has the potential to be used to fabricate nearly any superconducting Nb3Sn structure using either the Bronze Route (BR), Internal Tin (IT), External Tin (ET) processes as well as normal conducting pure copper (Cu) cavities. Most of the heat treated samples that were examined using SEM/EDX seemed to show a reasonable correlation of T c onset and transition width (ΔT c ) of the ingots initial/starting Sn content to the desired stoichiometric Nb 3 Sn phase, where the lower starting Sn content coupons resulted in lower T c 's with broader transition widths and the higher starting Sn coupons resulted in higher T c 's with narrower ΔT c ’s. The best samples had T c onsets ~17-18 K and ΔT c 's < 2 K. Two samples were further tested for RF surface resistance (R s ) and Quality Factor (Q) at JLAB. Here, these RF measurements were performed at 7.4 GHz using a calorimetric technique and showed two transitions, one at ~ 8 K and another at ~ 14 K; values of R s were at least two orders of magnitude higher than similar high quality Nb 3 Sn films directly deposited substrates by JLAB and with another superconducting transition close to the superconducting transition temperature of niobium. Substantial improvements in the processing variables ranging from higher quality of the initial ingots with higher Sn content, to better electropolishing and reaction heat treatment regimens will be necessary to realize improved RF performance metrics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Protonated Tungsten Bronze (H x WO 3 ) Acts as an Easily Regenerable Reagent for PCET Reactions

In this study, protonated tungsten bronze powder (H x WO 3 ) was synthesized by a microwave heating technique from tungsten(VI) chloride in benzyl alcohol. This material facilitates a proton-coupled electron transfer (PCET) reaction with 2,2,6,6-tetramethyl-1-piperidinyloxyl (TEMPO) in toluene, an aprotic solvent, to form TEMPOH, evidenced by UV–vis analysis of the organic product and X-ray photoelectron spectroscopy (XPS) analysis showing the oxidation of W 5+ to W 6+ in the remaining powder. Then, under illumination in an acidic aqueous solution, the oxidized WO 3 powder reacts photochromically to regenerate H x WO 3 . The regenerated H x WO 3 reagent remains active for further PCET reactions.

Granular materials↗