Search NASA⌕ Search

SEARCH · Search NASA

Results for “Bale”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Moisture Content of Baled Forest and Urban Woody Biomass during Long-term Open Storage

Abstract. This article describes how the moisture content of baled woody biomass varied during long-term open-air storage under conditions in the Pacific Northwest region of the United States. Large rectangular bales of forest and urban biomass were produced beginning in August 2015 and periodically until June 2016. Weights were measured approximately monthly until the entire lot of bales was ground into fuel in December 2016. Because it was impractical to non-destructively obtain moisture content samples during the study, final moisture content was measured from the ground material. Estimated temporal moisture contents were back-calculated from the final dry weight and moisture content of bales. All bales dried considerably during the spring and summer months, achieving a minimum moisture content in the early fall of 15 to 29% (wb). Minimum early fall moisture content had no correlation with the initial moisture content at time of baling. The ending moisture content in December 2016 ranged from 44% to 57% (wb), with a mean moisture content of 53% (wb). Ending moisture content had no correlation with initial moisture content at the time of baling, but appeared to be related to the amount of fine versus coarse woody material in the bales. Bales of forest and urban woody biomass proved to be structurally stable during long-term storage to enable handling and final transport to a centralized grinding location. Keywords: Density, Logging, Baling, Bioenergy, Biofuel, Bundling, Forest operations, Forestry, MC, Seasonality, Transport, Woody biomass.

Agriculture↗

Techno-Economic Impact of Diesel Fuel, Labor, and Interest Rates on Bulk-Format and Round Bale Logistics Expenses for Switchgrass

Highlights System-wide sensitivity of bulk-format and round bale logistics responded to different degrees of expense inputs. Biomass size-reduction expenses for bulk-format were consistently less than round-bale chopping. Stack/reclaim operations with high-density-capacity equipment for bulk-format were the highest expenses. Clean-sheet design of stacker/reclaimer and self-compacting bulk trailer may significantly reduce expenses. Abstract . Deterministic cost analyses were conducted for a harvest, storage, preprocessing, and supply system providing 371,870 dry Mg (dMg) year-1 of milled switchgrass (SG) to a biorefinery from 21,929 ha of production fields within 72 km of the biorefinery. Varied input costs of diesel fuel, labor, and interest rate were input into a highly detailed cost analysis for bulk-format and baseline round bale logistics. These operational input factors, potentially reflecting an evolving economic climate or paradigm shift, were examined to provide insight into the cost to deliver preprocessed biomass feedstock for centralized commercial-scale conversions. Total annual costs per dry unit of SG were determined for all combinations of diesel fuel prices of $0.53 L-1, $0.92 L-1, and $1.32 L-1; total labor costs of $20.00 h-1, $28.85 h-1, and $40.00 h-1 singly and uniformly applied across all labor inputs; and three representative interest rates of 6%, 8%, and 12%. Increases in total cost most depended on increases in diesel fuel cost, followed by labor rate, and finally interest rate. Increases in fuel costs from $0.53 L-1 to $1.32 L-1 yielded a total cost increase of about $11.56 dMg-1 and $13.36 dMg-1 for bulk-format and round bale logistics, respectively, for all combinations of labor and interest rates. The overall increase in labor rate ($20.00 h-1 to $40.85 h-1) resulted in increased total costs of about $10.32 dMg-1 for bulk-format logistics and $9.94 dMg-1 for round bale logistics for all fuel and interest rates. The overall increase in interest rate (6% to 12%) resulted in increased total costs of about $6.72 dMg-1 for bulk-format logistics and $4.21 dMg-1 for round bale logistics for all fuel and labor rates. Increases in total costs for combined increases in fuel cost, labor rate, and interest rate were $28.60 dMg-1 and $27.48 dMg-1, yielding maximum total costs of $87.87 dMg-1 and $86.53 dMg-1 for bulk-format and round bale logistics, respectively. Costs were determined for existing equipment systems, including novel use of waste compaction and ejector semi-trailers. The highest potential for cost reductions may require clean-sheet equipment designs specifically tailored for SG, such as forage harvesters that direct-cut standing SG, mobilized stacker-reclaimer technology to not inhibit stack-area footprint, self-compacting ejector trailer technology, and bale grinding technology incorporating controlled mass feeding and shear failure elements. Keywords: Bales, Bioenergy, Bulk-format, Densification, Field chop, Logistics, Transportation

Agriculture↗

Impact of Collection Equipment on Ash Variability of Baled Corn Stover Biomass for Bioenergy

Cost-effective conversion of agricultural residues for renewable energy hinges not only on the material’s quality but also the biorefinery’s ability to reliably measure quality specifications. The ash content of biomass is one such specification, influencing pretreatment and disposal costs for the conversion facility and the overall value of a delivered lot of biomass. The biomass harvest process represents a primary pathway for accumulation of soil-derived ash within baled material. In this work, the influence of five collection techniques on the total ash content and variability of ash content within baled corn stover in southwest Kansas is discussed. The equipment tested included a mower for cutting the corn stover stubble, a basket rake, wheel rake, or shred flail to gather the stover, and a mixed or uniform in-feed baler for final collection. The results showed mean ash content to range from 11.5 to 28.2 % depending on operational choice. Resulting impacts on feedstock costs for a biochemical conversion process range from $5.38 to $22.30 Mg-1 based on the loss of convertible dry matter and ash disposal costs. Collection techniques that minimized soil contact (shred flail or nonmowed stubble) were shown to prevent excessive ash contamination, whereas more aggressive techniques (mowing and use of a wheel rake) caused greater soil disturbance and entrainment within the final baled material. Material sampling and testing were shown to become more difficult as within-bale ash variability increased, creating uncertainty around feedstock quality and the associated costs of ash mitigation.

09 BIOMASS FUELS↗

Fluctuant storage temperature increased the heterogeneous distributions of pH and fermentation products in large round bale silage

Abstract In practical of silage production, variations in the fermentation parameters of silage might be attributable to changes in weather data, especially for ambient temperature. The objective of this study was to investigate how the changed temperature of outside weather condition affects distributions of pH and fermentation products in large round bale silage. The bale silages (1.22 m × 1.25 m ø; density, about 168.9 kg dry matter [DM]/m 3 ) were produced by BR6090 Combi from New Holland Agriculture, wrapped with six layers of stretch film, stored at ambient temperature (2–20°C) and constant temperature (10°C; 15°C; 25°C) for 3, 9, 15, 45 and 90 days. Compared with other silages, silage stored at 25°C had higher ( p < 0.05) lactic acid content, lower ( p < 0.05) pH, butyric acid content and ammonia‐nitrogen (N) ratio of total N. Fluctuant storage temperature limited lactic acid fermentation process with delayed pH decline and continuous butyric production and crude protein (CP) degradation. The differences of pH, lactic acid, propionic acid and ammonia‐N were considerably less evident in the centre of silages stored at different temperatures, and they increased towards the boundaries. The data shows that fluctuant storage temperature had undesirable effect on the fermentation quality of silage, especially for the external part of silo; relatively high and stable storage temperature for initial stage of ensiling process was necessary, but did not promote a positive response to the homogeneous distributions of pH and fermentation products in large round bale silage.

Li, Ping↗

Anatomical Fraction segmentation in the biomass bales

The U.S. Department of Energy Bioenergy Technologies Office (BETO) is committed to the development of sustainable, nationwide, commercial biofuel production to displace petroleum-derived fuels, increase domestic energy production, and encourage the creation of a domestic bioenergy and bioproducts industry. Operating a commercial-scale bioenergy operation requires significant technological advancements for determining biomass feedstock quality during the preprocessing stage. Usage of non-food feedstocks- e.g., corn-stover, pine residue, and forest residue - at the biorefineries reduces strain on the food supply chain. But the non-food feedstock heterogeneity- physical size, shape, and chemical composition-poses a significant challenge during milling, conveyance, feeding, and biofuel conversion processes. 3D X-Ray imaging (CT) is capable of distinguishing material features by detecting density and compositional differences. But the inherent complexity introduced during harvesting and bailing makes the reconstruction and interpretation of baled biomass materials from x-ray data time consuming, laborious, and expensive. Feedstocks are low-density materials that produce small contrast differences in the x-ray images. This paper focuses on using the shape and texture properties, using 3D image processing techniques like 3D skeletonization, directional statistics to characterize and extract volumetric content of the different tissue samples in the biomass bales.

09 BIOMASS FUELS↗

Bale Truck, Biomass Transport, Construction

Combined construction/assembly process that includes material requirements for construction of a bale truck (tractor-trailer combination) for switchgrass or corn stover biomass transport, and apportions those materials to 1 kg of cargo. To access the model referenced in the report, please visit https://www.netl.doe.gov/energy-analysis/details?id=31B6CABF-E2A7-4CFD-B3BA-B39DC98EDC42.

09 BIOMASS FUELS↗

Predicting Field Efficiency of Round-Baling Operations in High-Yielding Biomass Crops

Model simulations for bioenergy harvest planning need to utilize equipment-capacity relationships for equipment operating under the high-yield conditions typical of a biomass crop. These performance assumptions have a direct bearing on the estimates of machine capacity, the number of machines required, and, therefore, the cost to fulfill the biorefinery plant demands for a given harvest window. Typically, two major issues in these models have been poorly understood: the available time required to complete the harvest operation (often called probability of workdays) and the capacity of the harvest equipment as impacted by yield. Simulations use annual yield estimates, which incorporate weather events, to demonstrate year-to-year effects. Some simulations also incorporate potential yield increases from genetically modified energy crops. There are limited field performance data for most current forage equipment used for harvesting high-yield biomass crops. Analysis shows that the impact of wrap/eject time for round balers resulted in a 50% reduction in achieved throughput capacity (Mg/h). After the maximum throughput is reached, the cost of the round bale operation (3.23 USD/Mg) is double that of the large-square baler (1.63 USD/Mg). The round baler achieved throughput capacity is 50% less (32.7 Mg/h compared to 71.0 Mg/h) than the large-square baler.

09 BIOMASS FUELS↗

Practical Considerations of Moisture in Baled Biomass Feedstocks

Agricultural residues make up a large portion of the immediately available biomass feedstock for renewable energy markets. Current collection and storage methods rely on existing feed and forage practices designed to preserve nutrients and properties of digestibility. Low-cost collection and storage practices that preserve carbohydrates across a range of inbound moisture contents are needed to assure the economic and technical success of the emerging biomass industry. This study examines the movement of moisture in storage and identifies patterns of migration resulting from several on-farm storage systems and their impacts on moisture measurement and dry matter recovery. Baled corn stover and energy sorghum were stored outdoors in uncovered, tarp-covered, or wrapped stacks and sampled periodically to measure moisture and dry matter losses. Interpolation between discrete sampling locations in the stack improved bulk moisture content estimates and showed clear patterns of accumulation and re-deposition. Atmospheric exposure, orientation, and contact with barriers (i.e., soil, tarp, and wrap surfaces) were found to cause the greatest amount of moisture heterogeneity within stacks. Although the bulk moisture content of many stacks remained in the range suitable for aerobic stability, regions of high moisture were sufficient to support microbial activity, thus support dry matter loss. Stack configuration, orientation, and coverage methods are discussed relative to impact on moisture management and dry matter preservation. Additionally, sample collection and data analysis are discussed relative to assessment at the biorefinery as it pertains to stability in storage, queuing, and moisture carried into processing.

09 BIOMASS FUELS↗

Bale Truck, Transport

This process includes all inputs for the raw material transportation for 1 kg of delivered switchgrass. To access the model referenced in the report, please visit https://www.netl.doe.gov/energy-analysis/details?id=BE99B6B0-FE9E-4C00-AA92-BFDF417BF5AD

09 BIOMASS FUELS↗

Biomass Feedstock National User Facility--Improving Bale Deconstruction and Material Flow

The project aims to reduce feedstock variability using a quality-by-design approach beginning when the biomass is introduced to the process and will continue through the size reduction process, which will yield the results of fine generation reduction, contaminant removal, control of the physical and chemical critical material attributes in the process, and management of the flowability.

09 BIOMASS FUELS↗

Barriers to Developing Sustainable Supply of Lignocellulosic Feedstock for Production of Biofuels

Thirteen unique storage conditions of baled corn stover biomass were studied to examine the impact of bale type, baling technique, and storage practice on moisture control and product degradation over time. Square bales were found to outperform round bales in terms of moisture regulation and physical stability across all treatment types and at all sampling times. Within square bales, the control of moisture content in short term storage (3 months) is comparable between tarped and untarped stacks. In long term storage (9 months), bale wrapping outperforms both tarped and open stacks. In terms of overall moisture control, stack tarping allows moisture to leave initially wet bales, but allows dry bales to gain large amounts of moisture over time. Initial moisture content was found to drive self-heating and depend heavily on storage practice. While differences in dry matter loss over time are unclear, bale stability was lowest in the untarped stack, moderate in tarped stacks, and greatest in wrapped stacks. Overall, bale storage has been shown to be a dynamic system which requires special judgment to be made depending on the state of inbound material and the desired storage duration.

Feedstock↗

Low-Moisture Switchgrass Bulk-Format Logistics Costs Based on Engineering Data

Abstract. Logistics costs that spanned harvest, transport, storage, preprocessing, and year-round delivery of 371,870 dMg year -1 of milled, low-moisture switchgrass (SG) to a local biorefinery were determined for bulk-format versus round-bale systems. Separate spreadsheet analyses were conducted for three diesel fuel prices ($0.53 L -1 , $0.92 L -1 , and $1.32 L -1 ) because of the wide range of fuel prices during the project. A detailed analysis scenario identified a common harvest period, equipment annual use, other equipment uses, and protected SG storage on gravel pad, along with equipment performances based on previously published tests primarily for commercially available equipment. The bulk-format system used a depot equipped with stacker/reclaimer technology for storage, whereas the round-bale system used field-side bale stacks for storage, with both systems assuming 6% losses, primarily attributed to storage. Results indicated total costs for bulk-format versus round-bale systems of $54.63 per dry Mg (dMg -1 ), $60.41 dMg -1 , and $66.21 dMg -1 versus $54.59 dMg -1 , $62.10 dMg -1 , and $67.93 dMg -1 corresponding with diesel fuel costs of $0.53 L -1 , $0.92 L -1 , and $1.32 L -1 , respectively. The most significant bulk-format system total cost of $22.79 dMg -1 was associated with a stacker/reclaimer, conveyance, and dust collection at the depot, which was 42% of total costs at a diesel fuel cost of $0.53 L -1 . For the round-bale system, bale chopping total costs was highest and represented an average of 27% of total costs, with costs ranging from $14.63 dMg -1 to $19.08 dMg -1 for diesel fuel input costs ranging from $0.53 L -1 to $1.32 L -1 , respectively. For comparison, the forage harvester provided harvesting and chopping in the bulk-format system at total costs ranging from $6.47 dMg -1 to $8.80 dMg -1 across the same range of diesel fuel input cost. The forage harvester provided an economic advantage in size reduction compared to tub grinding. Truck hauling for both the bulk-format and round-bale systems represented significant expenses at all selected fuel costs. In addition, the multiple times that round bales were handled represented accumulating costs that were sensitive to diesel fuel costs. Keywords: Bales, Bioenergy, Bulk format, Densification, Field chop, Logistics, Transportation.

Agriculture↗

1.2.1.1 Harvest, Collection and Storage Quarter 3 Milestone Report

Single pass baling of corn stover is required in order to meet targets for the herbaceous biomass 2017 logistics design case. Single-pass pass stover harvest is based on the grain harvest and generally results in stover with a moisture content of 30-50% wet basis (w.b). Aerobic storage of corn stover with high moisture results in high levels of dry matter loss (DML), up to 25%. Anaerobic storage (ensiling) reduces DML to less than 5%, but additional costs are associated with handling and transporting the extra moisture in the biomass. This milestone provides a best-estimate of costs for using high moisture feedstock within the conventional baled logistics system. The costs of three (3) anaerobic storage systems that reduce dry matter losses (bale wrap, silage tube, and silage drive over pile) are detailed in this milestone and compared to both a conventional dry-baled corn stover case and a high moisture bale case, both stored aerobically. The total logistics cost (harvest, collection, storage, and transportation) of the scenarios are as follows: the conventional multi-pass dry bale case and the single-pass high moisture case stored aerobically were nearly equivalent at $61.15 and $61.24/DMT. The single-pass bale wrap case was the lowest at $57.63/DMT. The bulk anaerobic cases were the most expensive at $84.33 for the silage tube case and $75.97 for the drive over pile, which reflect the additional expense of transporting high-moisture bulk material; however, a reduction in preprocessing costs may occur because these feedstocks are size reduced in the field. In summary, the costs estimates presented in this milestone report can be used to determine if anaerobic storage of high-moisture corn stover is an economical option for dry matter preservation.

09 BIOMASS FUELS↗

Corn Stover Availability for Biomass Conversion: Situation Analysis

As biorefining conversion technologies become commercial, feedstock availability, supply system logistics, and biomass material attributes are emerging as major barriers to the availability of corn stover for biorefining. While systems do exist to supply corn stover as feedstock to biorefining facilities, stover material attributes affecting physical deconstruction, such as densification and post-harvest material stability, challenge the cost-effectiveness of present-day feedstock logistics systems. In addition, the material characteristics of corn stover create barriers with any supply system design in terms of equipment capacity/efficiency, dry matter loss, and capital use efficiency. However, this study of a large, square-bale corn stover feedstock supply system concludes that (1) where other agronomic factors are not limiting, corn stover can be accessed and supplied to a biorefinery using existing bale-based technologies, (2) technologies and new supply system designs are necessary to overcome biomass bulk density and moisture material property challenges, and (3) major opportunities to improve conventional-bale biomass feedstock supply systems include improvements in equipment efficiency and capacity and reducing biomass losses in harvesting and collection and storage. Finally, the backbone of an effective stover supply system design is the optimization of intended and minimization of unintended material property changes as the corn stover passes through the individual supply system processes from the field to the biorefinery conversion processes.

09 BIOMASS FUELS↗

Evaluation of mixed #3–7 plastic waste from material recovery facilities (MRFs) in the United States

Plastic recycling rates are still low in the United States (U.S.), with less than 10% of municipal solid waste (MSW) plastic being recycled. Most unrecycled plastics are identified by Resin Identification Codes (RIC) from #3–7, which are commonly destined for landfill or waste-to-energy facilities (WTE). Therefore, the composition and quality of outbound bales containing #3–7 plastics were assessed to understand the potential to increase recycling rates. Three bales were sourced from three different Material Recovery Facilities (MRFs) located in the United States. Each bale was manually sorted and characterized for quality and performance via multiple plastic characterization techniques. Considerable differences in bale composition were observed between MRFs, which correlated with the technology used by each MRF in the sorting process. The differences were substantial in the residual levels of poly(ethylene terephthalate) (PET) and high-density polyethylene (HDPE), which are highly desired for mechanical recycling processes and not expected in #3–7 plastics bales. Traditional recycling processes including washing, extrusion, and injection molding of the sorted material were employed prior to the physical, thermal, and molecular characterization. Despite differences in bale composition by plastic type, some polymer properties were similar across MRFs. Here, this research suggests that landfill-diverted mixed plastic waste can be utilized in the mechanical recycling of currently unrecycled materials, as processes can be designed to work with consistent polymer properties. It also highlights the need to upgrade the sorting systems to prevent waste feedstocks, which can be recycled with current technologies, from contaminating other plastic streams or reach landfills.

36 MATERIALS SCIENCE↗