Search NASA⌕ Search

SEARCH · Search NASA

Results for “Bench Experiment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Bench scale experiments for the remediation of Hanford Waste Treatment Plant low activity waste melter off-gas condensate

The Low Activity Waste (LAW) vitrification facility at the Hanford Waste Treatment and Immobilization Plant (WTP) will generate an aqueous condensate recycle stream (LAW Off-Gas Condensate) from the off-gas system. The plan for disposition of this stream during baseline operations is to send it to the WTP Pretreatment Facility, where it will be blended with LAW, concentrated by evaporation and recycled to the LAW vitrification facility again. The primary reason to recycle this stream is so that the semi-volatile 99Tc isotope eventually becomes incorporated into the glass. This stream also contains non-radioactive salt components that are problematic in the melter, so diversion of this stream to another process would eliminate recycling of these salts and would enable simplified operation of the LAW melter and the Pretreatment Facilities. This diversion from recycling this stream within WTP would have the effect of decreasing the LAW vitrification mission duration and quantity of glass waste. The concept being tested here involves removing the 99 Tc so that the decontaminated aqueous stream, with the problematic salts, can be disposed elsewhere.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Actinide Recovery Experiments with Bench-Scale Liquid Cadmium Cathode in Fission Product-Laden Molten Salt

This article summarizes the observations and analytical results from a series of bench- scale liquid cadmium cathode experiments that recovered transuranic elements together with uranium from a molten electrolyte laden with real fission products. Variable parameters such as the ratio of Pu3+/U3+ in the electrolyte, liquid cadmium cathode voltage, and feed materials were tested in the LCC experiments. Actinide recovery efficiency and Pu/U ratio in the liquid cadmium cathode product under variable conditions are reported in the article. Separation factors for actinides and rare earth elements in the salt/cadmium system are also presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Bench Measurement of the Energy Loss of a Stored Beam to a Cavity

A rather simple electronic bench experiment is proposed for obtaining a measure of the impulse energy loss of a stored particle bunch to an rf cavity or other vacuum-chamber structure--the so-called "cavity radiation". The proposed method is analyzed in some detail.

43 PARTICLE ACCELERATORS↗

R&D of a high-performance DIRC detector for a future electron-ion collider

An Electron-Ion Collider (EIC) is proposed as the next big scientific facility to be built in the United States, costing over $1 billion in design and construction. Each detector concept for the electron/ion beam interaction point is integrated into a large solenoidal magnet. The necessity for excellent hadronic particle identification (pion/kaon/proton) in the barrel region of the solenoid has pushed research and development (R&D) towards a new, high-performance Detection of Internally Reflected Cherenkov light (DIRC) detector design. The passage of a high energy charged particle through a fused silica bar of the DIRC generates optical Cherenkov radiation. A large fraction of this light propagates by total internal reflection to the end of the bar, where the photon trajectories expand in a large volume before reaching a highly segmented photo-detector array. The spatial and temporal distribution of the Cherenkov light at the photo-detector array allows one to reconstruct the angle of emission of the light relative to the incident charged particle track. In order to reach the desired performance of 3sigma pi/K separation at 6 GeV/c particle momentum a new 3-layer spherical lens focusing optic with a lanthanum crown glass central layer was designed to have a nearly at focal plane. In order to validate the EIC DIRC simulation package, a synergistic test beam campaign was carried out in 2015 at the CERN PS with the PANDA Barrel DIRC group using a prototype DIRC detector. Along with the analysis of the CERN test beam data, measurements of the focal plane of the 3-layer lens were performed using a custom-built laser setup at Old Dominion University. Radiation hardness of the lanthanum crown glass was tested using a 160 keV X-ray source and a monochromator at the Catholic University of America. Results of these test-bench experiments and the analysis of the 2015 CERN test beam data are presented here.

43 PARTICLE ACCELERATORS↗

Impacts of Biofuel Blending on MCCI Ignition Delay with Review of Methods for Defining Cycle-by-Cycle Ignition Points from Noisy Cylinder Pressure Data

Conventional diesel combustion, also known as Mixing-Controlled Compression Ignition (MCCI), is expected to be the primary power source for medium- and heavy-duty vehicles for decades to come. Displacing petroleum-based ultra-low-sulfur diesel (ULSD) as much as possible with low-net-carbon biofuels will become necessary to help mitigate effects on climate change. Neat biofuels may have difficulty meeting current diesel fuel standards but blends of 30% biofuel in ULSD show potential as ‘drop-in’ fuels. These blends must not make significant changes to the combustion phasing of the MCCI process if they are to be used interchangeably with neat ULSD. An important aspect of MCCI phasing is the ignition delay (ID), i.e. the time between the start of fuel injection and the initial premixed autoignition that initiates the MCCI process. Bench experiments can evaluate the expected ignition delay of a fuel via cetane number (CN) or alternative methods such as the indicated cetane number (ICN); however, neither CN nor ICN correlate perfectly with the ignition delay measured in actual engine experiments. Furthermore, there is no standardized methodology on how to quantify MCCI ignition delay from engine cylinder pressure measurements, creating difficulties in cross-study comparison. In this study, several engine ignition delay calculation methods are evaluated for robustness in deriving ignition delay on both a cycle-averaged and cycle-to-cycle basis. Eight biofuel blends with varying ICN, oxygen concentration and other fuel properties were used to study the different methods. This yields a thorough analysis of how certain biofuel blends affect ignition delay and the entire MCCI process, as well as a thorough evaluation of the differences between the ID calculation methods. Many of these methods are equally valid, but the choice of method has a significant impact on the resulting ID, which must be carefully considered when evaluating results across multiple studies.

47 OTHER INSTRUMENTATION↗

Impacts of Biofuel Blending on MCCI Ignition Delay with Review of Methods for Defining Cycle-by-Cycle Ignition Points from Noisy Cylinder Pressure Data: Preprint

Conventional diesel combustion, also known as Mixing-Controlled Compression Ignition (MCCI), is expected to be the primary power source for medium- and heavy-duty vehicles for decades to come. Displacing petroleum-based ultra-low-sulfur diesel (ULSD) as much as possible with low-net-carbon biofuels will become necessary to help mitigate effects on climate change. Neat biofuels may have difficulty meeting current diesel fuel standards but blends of 30% biofuel in ULSD show potential as ‘drop-in’ fuels. These blends must not make significant changes to the combustion phasing of the MCCI process if they are to be used interchangeably with neat ULSD. An important aspect of MCCI phasing is the ignition delay (ID), i.e. the time between the start of fuel injection and the initial premixed autoignition that initiates the MCCI process. Bench experiments can evaluate the expected ignition delay of a fuel via cetane number (CN) or alternative methods such as the indicated cetane number (ICN); however, neither CN nor ICN correlate perfectly with the ignition delay measured in actual engine experiments. Furthermore, there is no standardized methodology on how to quantify MCCI ignition delay from engine cylinder pressure measurements, creating difficulties in cross-study comparison. In this study, several engine ignition delay calculation methods are evaluated for robustness in deriving ignition delay on both a cycle-averaged and cycle-to-cycle basis. Eight biofuel blends with varying ICN, oxygen concentration and other fuel properties were used to study the different methods. This yields a thorough analysis of how certain biofuel blends affect ignition delay and the entire MCCI process, as well as a thorough evaluation of the differences between the ID calculation methods. Many of these methods are equally valid, but the choice of method has a significant impact on the resulting ID, which must be carefully considered when evaluating results across multiple studies.

47 OTHER INSTRUMENTATION↗

An Inorganic Microsphere Composite for the Selective Removal of 137 Cesium from Acidic Nuclear Waste Solutions 2: Bench-Scale Column Experiments, Modeling, and Preliminary Process Design

A new inorganic ion exchange composite for removing radioactive cesium from acidic waste streams has been developed. The new material consists of ammonium molybdophosphate, (NH4)3P(Mo3O10)4?3H2O (AMP), synthesized within hollow aluminosilicate microspheres (AMP-C), which are produced as a by-product from coal combustion. The selective cesium exchange capacity of this inorganic composite was evaluated in bench-scale column tests using simulated sodium bearing waste solution as a surrogate for the acidic tank waste currently stored at the Idaho National Laboratory (INL). Total cesium loading on the columns at saturation agreed very well with equilibrium values predicted from isotherm experiments performed previously. A numerical algorithm for solving the governing partial differential equations (PDE) for cesium uptake was developed using the intraparticle mass transfer coefficient obtained from previous batch kinetic experiments. Solutions to the governing equations were generated to obtain the cesium concentration at the column effluent as a function of throughput volume using the same conditions as those used for the actual column experiments. The numerical solutions of the PDE fit the column break through data quite well for all the experimental conditions in the study. The model should therefore provide a reliable prediction of column performance at larger scales.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

TMIST-2 Transport Test

In anticipation of the TMIST-2 experiment in the Advanced Test Reactor, there was a need to determine if the tritium that is expected to be observed at the outlet of the experiment would be seen or if it may be lost on its way from the experiment in the core to the measurement station. To assist in resolving that issue, a bench-scale experiment was conducted in the Idaho National Laboratory’s Safety and Tritium Applied Research (STAR) facility using deuterium and a mass spectrometer in lieu of tritium with ion chambers, bubblers, and scintillation counting. The experiment replicated the concentration of the hydrogen isotope, the flow rates anticipated, and the residence times. It was found that there was initial uptake on tubing walls, presumably due to oxidation of the hydrogen isotopes to water and adsorption or isotopic exchange, but that saturates relatively quickly, and once saturated, the concentration of deuterium at the outlet of the tubing system was essentially the same as it was at the experiment inlet under the conditions modeled in the experiment.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Rainfall-driven Flooding Capability Development Report

Globally, floods are among the most frequent and costly natural disasters, both socially and economically. Many of these floods result from excess rainfall collecting in streams and rivers, then overtopping banks and flowing overland into urban environments, damaging critical infrastructure. In Fiscal Year 2012, the National Infrastructure Simulation and Analysis Center’s (NISAC) goal was to enhance its existing flood modeling and simulation capability to be able to estimate flooding from rainfall-runoff events. To accomplish this task, NISAC modified the existing flood modeling code-base using commodity high-performance computing hardware, making it more suitable for regional rainfall events. NISAC also implemented new modules within the existing flood code to account for hydrologic processes, such as spatially variable rainfall and infiltration. Analysts subjected the new hydrologic model to a verification and validation process, wherein analysts evaluated the model using a bench-scale experiment and watershed scale rainfall-runoff events. The bench-scale experiment indicated that the new hydrologic model is mass and momentum conserving and can adequately simulate runoff for depths of inches of water. The watershed scale simulations indicated that the hydrologic model is a good predictor of the discharge hydrograph when compared to observations if the input parameters, such as roughness and hydraulic conductivity, are adequately calibrated. The intended use of the hydrologic model is to estimate flood potential during extreme rainfall events. The accuracy of the predictions is largely dependent on the availability of accurate spatial data for soil and roughness parameters. In addition, each simulation should be accompanied with a calibration exercise, which requires historical rainfall and river discharge observations.

13 HYDRO ENERGY↗

Rare Earth Elements (REEs) Measurement in Coal and Rock Mineral Matrices

Although critical minerals including rare earth elements (REEs) can be analyzed in laboratory by some established and reliable laboratory based analytical techniques, their in-situ measurements in the field have always been challenging. For identification of REE-rich sites and REEs distribution measurement, portable field applicable technologies are paramount. As Laser-induced breakdown spectroscopy (LIBS) has enormous potential for field measurement, it has been explored for REEs measurements by many research groups. However, most of the studies are still dealing with simulated samples with traditional bench top experiments. In real world, REEs are available in various types of natural complex matrices in low content depending on the geographical locations. Considering this, LIBS has been evaluated for REE measurement in two different complex coal and rock mineral matrices representing some natural REE-rich sites. In addition, multiple samples collected from some natural sites in Wyoming, USA were experimented by using NETL’s bench top as well as miniaturized prototype setups for REE measurements.

Bhatt, Chet R.↗

Effects of carbon treating on piperazine oxidation in pilot plant testing of PZAS™

From February to June 2019, a pilot plant campaign was run for 2100 h at the National Carbon Capture Center (NCCC) using moderately degraded 5 m PZ with simulated flue gas equivalent to a 0.64 MW natural gas combined cycle. Piperazine with the Advanced Stripper™ (PZAS™) and a baghouse were used, and N 2 sparging was applied at the bottom of the absorber. A carbon bed was activated and showed beneficial effects in removing degradation products and reducing the oxidation rate. The cumulative NH 3 production was 180 mmol/k, indicating a PZ oxidation rate of 0.07 mmol/kg/h (0.3 kg PZ/tonne of CO 2 ). The total formate before turning on the carbon bed was 41 mmol/kg, and the total Fe was 0.1 mmol/kg. Carbon treating reduced NH3 production from 0.1 mmol/kg/h to 0.056 mmol/kg/h after 400 h of operation, reduced the UV-Vis absorbance of the samples at 320 nm, and caused a decrease of dissolved Cr. Bench-scale experiments were performed using the NCCC solvent and the same type of carbon. In bench-scale experiments, the UV-Vis absorbance and the concentration of Fe, Mn, and Cr all decreased. Finally, a linear equilibrium relationship was observed between the UV-Vis absorbance and the carbon loading.

03 NATURAL GAS↗

Modeling of Gas-Liquid Flow Through An Interconnected Channel Matrix

The motion of a less viscous, non-wetting gas into a liquid-saturated porous medium is known as drainage. Drainage is an important process in environmental applications, such as enhanced oil recovery and geologic CO2 sequestration. Understanding what conditions will increase the volume of gas that can saturate an initially water-saturated porous medium is of importance for predictions of the total CO2 volume that can be sequestered in known geologic formations. To further the understanding of how drainage flow properties are related to different injection flow-rates, a porous medium consisting of interconnected channels and pores was manufactured to perform bench-top experiments of drainage. Additionally, a finite-volume model of this interconnected channel matrix was constructed. Numerical simulations of constant-rate injection into the model porous medium are first shown to compare favorably to the bench-top experiments. The fluid and injection properties of the drainage process were then varied to evaluate the flow conditions which would maximize the volume of gas trapped within the porous medium. In particular, CO2 displacing brine within the porous medium was modeled, with representative subsurface temperatures and fluid properties. It was shown with these fluid conditions a higher final saturation of the invading less-viscous CO2 was obtained, as compared to air into water experiments at similar injection rates.

10 SYNTHETIC FUELS↗

Development of Membrane Distillation Technology Utilizing Waste Heat for Treatment of High Salinity Wastewaters

Membrane distillation (MD) can serve as a cost effective method to treat high salinity wastewaters, especially if waste heat is utilized for its operation. The goal of this work is to study the feasibility of employing MD technology for the treatment of high salinity wastewaters which are generated as a result of natural gas production and active reservoir management for CO 2 sequestration. This study also aimed at quantifying the availability of waste heat which could be used as the primary source of thermal energy to drive the MD process. Bench scale studies were carried out with several commercially available membranes using both synthetic and actual high salinity wastewaters. The membranes tested with real wastewater samples exhibited excellent rejection of dissolved ions, including naturally occurring radioactive material (NORM). Long term bench scale experiments with real produced water from the Marcellus shale play revealed that iron oxide could precipitate on the feed side of direct contact MD (DCMD) module but had a negligible effect on the performance of the system. Based on the bench scale experiments, an ASPEN Plus simulation, which incorporated a mathematical model with fundamental heat and mass transfer equations, was developed and used to evaluate the process energy requirements. Despite low operating temperature and pressure for MD, it had a large thermal energy requirement for operation, which could make this technology expensive compared to reverse osmosis (RO) and forward osmosis (FO). However, it is important to note that RO and FO have limited applicability for high salinity shale gas wastewater. Moreover, MD could be integrated with renewable energy sources such as wind or solar energy or industrial waste heat sources to offset the thermal energy requirements and enhance the economics of wastewater treatment. Natural gas compressor stations (NG CS) have been proposed in this study as the source of waste heat based on the estimate of quantity and quality of available waste heat in the exhaust streams of gas turbine and internal combustion compressor engines. Using the actual installed capacity and location of compressor stations in the U.S., this analysis revealed that an average of 610 TJ/day of thermal energy is available at existing NG CS and that this source of waste heat is of high quality with temperatures above 645 K. A systems-level integration of MD with waste heat from NG CS revealed that approximately 56% of available waste heat at NG CS in Pennsylvania is sufficient to concentrate (from 10% to 30% salinity) all wastewater associated with shale gas extraction. Techno-economic assessment (TEA) accounting for capital as well as operating and maintenance costs with and without waste heat integration was conducted for a hypothetical 0.5 million gallons per day (MGD) DCMD plant using experimental and modeling results from this study. TEA revealed that the total cost of shale gas wastewater treatment using MD is $5.7/m 3 feed for the base case scenario in which the thermal energy requirements are met by external steam, however, the total cost can be reduced to $0.74/m 3 feed when integrated with free waste heat from NG CS. Sensitivity analysis revealed that thermal energy cost and feed TDS are the most important factors in total cost of high salinity wastewater treatment using DCMD.

03 NATURAL GAS↗

Bench-scale Kinetics Study of Mercury Reactions in FGD Liquors

This document is the final report for Cooperative Agreement DE-FC26-04NT42314, 'Kinetics Study of Mercury Reactions in FGD Liquors'. The project was co-funded by the U.S. DOE National Energy Technology Laboratory and EPRI. The objective of the project has been to determine the mechanisms and kinetics of the aqueous reactions of mercury absorbed by wet flue gas desulfurization (FGD) systems, and develop a kinetics model to predict mercury reactions in wet FGD systems. The model may be used to determine optimum wet FGD design and operating conditions to maximize mercury capture in wet FGD systems. Initially, a series of bench-top, liquid-phase reactor tests were conducted and mercury species concentrations were measured by UV/visible light spectroscopy to determine reactant and byproduct concentrations over time. Other measurement methods, such as atomic absorption, were used to measure concentrations of vapor-phase elemental mercury, that cannot be measured by UV/visible light spectroscopy. Next, a series of bench-scale wet FGD simulation tests were conducted. Because of the significant effects of sulfite concentration on mercury re-emission rates, new methods were developed for operating and controlling the bench-scale FGD experiments. Approximately 140 bench-scale wet FGD tests were conducted and several unusual and pertinent effects of process chemistry on mercury re-emissions were identified and characterized. These data have been used to develop an empirically adjusted, theoretically based kinetics model to predict mercury species reactions in wet FGD systems. The model has been verified in tests conducted with the bench-scale wet FGD system, where both gas-phase and liquid-phase mercury concentrations were measured to determine if the model accurately predicts the tendency for mercury re-emissions. This report presents and discusses results from the initial laboratory kinetics measurements, the bench-scale wet FGD tests, and the kinetics modeling efforts.

01 COAL, LIGNITE, AND PEAT↗

Final Technical Report: Plasma Arc Gasification Based Rare Earth Element Recovery from Coal Fly Ash

Southern Research, as the primary awardee, with sub-awardees ArcSec Technologies, LLC (ArcSec) and Reaction Engineering International (REI) have investigated a plasma arc based thermal process intended to concentrate rare earth elements (REE) from coal fly ash. Successful demonstration of the technology would contribute to the effort for realizing a competitive, domestic REE value chain thereby reducing U.S. dependence on foreign supply, maintaining national security interests, and creating opportunities for economic growth. The originally proposed concept included two technology options – 1) a smelting process and 2) a smelting plus vaporization and condensation process. For both options, coal fly ash would be smelted in a plasma arc heated furnace under reducing conditions to separate ash into molten slag and reduced metal (primarily iron) phases. During smelting, it was expected that the REE would also be reduced to metals and partition mostly to the iron phase. During the first year of work, sample coal ash feedstocks were acquired and characterized, feasibility of the smelting process was evaluated in bench-scale experiments, and the vaporization/condensation process was investigated through equilibrium and CFD modeling studies. From the feedstock characterization, REE content for the coal ash samples obtained was measured to be in the range of 302 – 1219 ppm with average at 537 ppm. Though it was successfully demonstrated that ash could be separated into slag and metal phases, the bench-scale experiments were only marginally successful at collecting REE in the metal phase. Producing REE concentrates near the DOE goal of 2%, however, has not been achieved. From the modeling studies, the vaporization/condensation process was predicted to be effective for separating individual REE and producing enriched metal fractions with total REE content higher than 2%, provided the smelting process performed as intended. Supplemental smelting experiments and thermodynamic modeling studies, conducted during the second year of work, indicated a number of technical modifications that could lead to producing higher REE concentrates from coal ash. The strategy shifted to reducing as much of the ash oxides to metals as possible, leaving the REE more concentrated in the remaining slag. Results from later experiments based on the modified approach showed improvements in REE recovery and concentration levels in smelted products. SEM-EDS analyses on product specimens showed agglomerations of reduced metal REE crystals at much larger length-scales as compared to REE content in raw ash.

01 COAL, LIGNITE, AND PEAT↗

Biostimulated uranium immobilization within aquifers – from bench scale to field experiments

In situ bioremediation of uranium-contaminated aquifers through microbially catalyzed reduction of mobile U(VI) species can only be successful if the U(IV) products are immobilized over long time-scales. Although uraninite is known for its low solubility and has been produced in nano-particulate form by several species of metal- and sulfate-reducing bacteria in laboratory studies, little is known about the stability of biogenic U(IV) in the subsurface. Using an up-scaling approach, we investigated the chemical and environmental stability of biogenic UO₂ nano-solids. Our results show that diffusive limitations due to aquifer porosity and microstructure may retard uraninite corrosion. Corrosion was also retarded by adsorption or incorporation of manganese. On the other hand, U(VI) bioreduction in field sediments generated U(IV) that was more labile than biogenic UO₂.

bioremediation↗

Coalbed Methane Procduced Water Treatment Using Gas Hydrate Formation at the Wellhead

Water associated with coalbed methane (CBM) production is a significant and costly process waste stream, and economic treatment and/or disposal of this water is often the key to successful and profitable CBM development. In the past decade, advances have been made in the treatment of CBM produced water. However, produced water generally must be transported in some fashion to a centralized treatment and/or disposal facility. The cost of transporting this water, whether through the development of a water distribution system or by truck, is often greater than the cost of treatment or disposal. To address this economic issue, BC Technologies (BCT), in collaboration with Oak Ridge National Laboratory (ORNL) and International Petroleum Environmental Consortium (IPEC), proposed developing a mechanical unit that could be used to treat CBM produced water by forming gas hydrates at the wellhead. This process involves creating a gas hydrate, washing it and then disassociating hydrate into water and gas molecules. The application of this technology results in three process streams: purified water, brine, and gas. The purified water can be discharged or reused for a variety of beneficial purposes and the smaller brine can be disposed of using conventional strategies. The overall objectives of this research are to develop a new treatment method for produced water where it could be purified directly at the wellhead, to determine the effectiveness of hydrate formation for the treatment of produced water with proof of concept laboratory experiments, to design a prototype-scale injector and test it in the laboratory under realistic wellhead conditions, and to demonstrate the technology under field conditions. By treating the water on-site, producers could substantially reduce their surface handling costs and economically remove impurities to a quality that would support beneficial use. Batch bench-scale experiments of the hydrate formation process and research conducted at ORNL confirmed the feasibility of the process. However, researchers at BCT were unable to develop equipment suitable for continuous operation and demonstration of the process in the field was not attempted. The significant achievements of the research area: Bench-scale batch results using carbon dioxide indicate >40% of the feed water to the hydrate formation reactor was converted to hydrate in a single pass; The batch results also indicate >23% of the feed water to the hydrate formation reactor (>50% of the hydrate formed) was converted to purified water of a quality suitable for discharge; Continuous discharge and collection of hydrates was achieved at atmospheric pressure. Continuous hydrate formation and collection at atmospheric conditions was the most significant achievement and preliminary economics indicate that if the unit could be made operable, it is potentially economic. However, the inability to continuously separate the hydrate melt fraction left the concept not ready for field demonstration and the project was terminated after Phase Two research.

01 COAL, LIGNITE, AND PEAT↗