SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Final report for the Bethel (Alaska) Wind Construction project. Under this project, Alaska Village Electric Cooperative, Inc. (AVEC) constructed and commissioned one new 900 kW-capacity wind turbine at a site in Bethel about 3.3 miles NE of the diesel-fired prime power plant. The wind generator’s output will augment the prime source generation provided by the diesel-powered generators.
‘Cedar Creek’ (Reg. no. CV-290, PI 700113) switchgrass (Panicum virgatum L.) was selected for increased winter survivorship for three cycles, using surviving plants from ‘Kanlow’. The first two cycles were conducted at multiple locations in Wisconsin, and the third cycle was conducted at the Cedar Creek Ecosystem Science Reserve, East Bethel, MN. All seed production and increases were conducted by either Illinois State University or the University of Illinois. Field evaluations of the third-cycle population were conducted at five locations in Wisconsin between 2017 and 2021, located within USDA hardiness zones 3–5. Field experiments were planted in both 2016 and 2017. Averaged over the five locations and all trial years, Cedar Creek had 91% ground cover, compared with 96% for Cave-in-Rock, 95% for Shawnee, and 91% for Liberty. Biomass yield of Cedar Creek averaged 12.17 Mg ha –1 , which was 20% higher than Liberty, 30% higher than Cave-in-Rock, 31% higher than Shawnee, and 520% higher than Kanlow. Cedar Creek is a high-biomass lowland-type of switchgrass and is the first lowland-type adapted to USDA hardiness zones 3–5. Cedar Creek was released to the public by USDA-ARS in 2021.
From February through September 2017, Cultural Resource Analysts, Inc. personnel completed a historic architectural resource survey of the Oak Ridge National Laboratory in Roane and Anderson Counties, Tennessee. The survey was completed at the request of UT-Battelle, LLC, the private not-for-profit company that manages and operates Oak Ridge National Laboratory for the U.S. Department of Energy. The purpose of the survey was to assist the Department of Energy in complying with the National Historic Preservation Act of 1966, as amended, by providing updated recommendations regarding the National Register of Historic Places eligibility of historic architectural resources at Oak Ridge National Laboratory. The survey included the entirety of Oak Ridge National Laboratory’s main campus that occupies approximately 1,100 acres in Bethel and Melton Valleys and on Chestnut Ridge. Based on Facilities Information Management System data and guidance provided by UT-Battelle, LLC, preservation and modernization staff, the survey team developed a list of resources for inclusion in the survey. The list included all substantial buildings constructed in or before 1980 in order to provide sufficient coverage of buildings that will turn 50 years of age within the next decade. Only those buildings with recorded area over 100 sq ft were included in the survey. Additionally, the UT-Battelle team identified 15 buildings for more intensive survey because such buildings are central to Oak Ridge National Laboratory’s future mission needs and are expected to undergo renovations in the foreseeable future. These building were subject to both exterior and interior documentation with particular focus on identifying character-defining features, and thus were subject to more detailed analysis than the other resources included in the survey. The findings of this historic resource survey build on the conclusions of the 1994 survey by DuVall & Associates, Inc., as well as the survey updates completed by Thomason and Associates in 2004 and 2015 in support of the Oak Ridge National Laboratory Historic Preservation Plan. Within 12 distinct areas of Oak Ridge National Laboratory, as well as outlying areas, the survey recorded 195 buildings and structures constructed in or before 1980. In consideration of the role and significance of each area and each individual resource within the context of Oak Ridge National Laboratory, and in light of their current integrity and condition, each recorded resource was evaluated to determine if it is eligible for listing in the National Register of Historic Places.
This plan describes the systematic approach for: inspecting the physical condition of monitoring wells at Y-12, determining maintenance needs that extend the life of a well, and identifying those wells that no longer meet acceptable monitoring well design or well construction standards and require plugging and abandonment. The inspection and maintenance of groundwater monitoring wells is one of the primary management strategies of the Y-12 Groundwater Protection Program (GWPP) Management Plan, that is, the “proactive stewardship of the extensive monitoring well network at Y-12" (Consolidated Nuclear Security, L.L.C. [CNS], 2018). Effective stewardship, and a program of routine inspections of the physical condition of each monitoring well, ensures that representative water-quality samples and hydrologic data are obtained from the well network and protects the subsurface environment. In accordance with the Y-12 GWPP Monitoring Optimization Plan (MOP) for Groundwater Monitoring Wells at the Y-12 National Security Complex, Oak Ridge, Tennessee (CNS, 2017), the status designation (active or inactive) for each well determines the scope and extent of well inspections and maintenance activities. This plan, in conjunction with the above document, formalizes the GWPP approach to focus available resources on monitoring wells which provide the most useful data, and for that reason the GWPP inspects and performs maintenance on the wells sampled by the GWPP. This plan applies to groundwater monitoring wells installed at Y-12 and the related waste management facilities located within the three hydrogeologic regimes: (1) the Bear Creek Hydrogeologic Regime (Bear Creek Regime), (2) the Upper East Fork Poplar Creek Hydrogeologic Regime (East Fork Regime), and (3) the Chestnut Ridge Hydrogeologic Regime (Chestnut Ridge Regime). The Bear Creek Regime encompasses the section of Bear Creek Valley (BCV) immediately west of Y-12. The East Fork Regime encompasses most of the Y-12 process, operations, and support facilities in BCV west of Scarboro Road. The Chestnut Ridge Regime is directly south of Y-12 and encompasses a section of Chestnut Ridge that is bounded to the west by a surface drainage feature (Dunaway Branch, located immediately west of Industrial Landfill II) and by Scarboro Road to the east. The GWPP maintains an extensive database of geographic and construction details and related information for the monitoring wells in each hydrogeologic regime in the Updated Subsurface Database for Bear Creek Valley, Chestnut Ridge, and Parts of Bethel Valley on the U.S. DOE Oak Ridge Reservation (CNS, 2019). A detailed description of the hydrogeologic framework at Y-12 can be found in the GWPP Management Plan (CNS, 2018).
The Calista Energy Management Assistance Initiative (CEMAI) provided technical assistance and capacity building for 56 Tribal communities in the Calista Region of Alaska as an effort to reduce costs, improve operational efficiency, enhance human capacity, and job opportunities. CEMAI catalyzed and guided numerous efforts into a consolidated and effective initiative that brought rural energy best practices, economies of scale, operational efficiencies, human capacity, and economic development to the forefront. Calista Corporation (Calista) is one of thirteen Alaska Native Regional Corporations created under the Alaska Native Claims Settlement Act of 1971 (ANCSA) in the settlement of aboriginal land claims. Calista was incorporated in Alaska on June 12, 1972. The Calista Region covers Alaska’s Bethel and Kusilvak (formerly Wade Hampton) Census areas and includes 56 communities. Calista partnered with Nuvista Light and Electric Cooperative (Nuvista) on the Department of Energy, Office of Indian Energy (DOE-OIE), CEMAI project. Nuvista is a non-profit that seeks to reduce energy costs and provide renewable sources of energy to the people of western Alaska. It is founded and led by a non-profit, Tribe, Native Corporations (including Calista), energy organizations, and Alaska Native stakeholders in the Yukon-Kuskokwim Delta (YK-D) Region; covering the same service boundaries and communities served by Calista. This partnership allowed Calista to direct the project work with local energy experts to respond to community needs. In this arrangement, Calista added credibility and regional accountability while Nuvista added energy-specific expertise and skill set in project management. The delivery of the CEMAI Workplan included short-term or on-demand responses to specific technical assistance requests from communities in addition to longer-term strategically directed activities such as workshops, coordinated training, and capacity development efforts across the region. CEMAI’s Workplan aimed to enhance communities’ readiness for establishing renewable energy projects and implementing energy efficiency initiatives. The CEMAI objectives included: (1) Identifying common operational needs and improvement opportunities for entities with an energy interest or responsibility. (2) Providing access to multi-level expertise to address existing challenges. (3) Developing specialized training programs to build local capacity and community readiness. (4) Nurturing the creation of regional support networks. (5) Increasing access to regional, state, and federal energy initiatives, funding, and expertise. (6) Improving technical skills, provide livable wages, and job opportunities.
This Phased Construction Completion Report (PCCR) documents completion of demolition, waste disposition, and slab stabilization activities of Building 2523 (Decontamination Laundry) for the Oak Ridge National Laboratory (ORNL). The Decontamination Laundry is located directly north of the intersection of White Oak Avenue and the 2519 Access Road. This demolition scope included the removal of the above-grade structures and facility components associated with Building 2523. This scope included the removal of Building 2523 (and all remaining contents inside), Trailer 2523A (and all remaining contents inside), an above-grade wastewater tank, and a wooden access porch connecting Buildings 2523 and Trailer 2523A. On the north side of Building 2523, above-grade portions of selected remaining foundations/stairs were removed from former Building 2517 to make room to stage waste containers. Building 2621 is west of the Laundry Building and Buildings 2547 and 2649 are to the east, while Building 2525 is to the north. Building 2523 is located within Bethel Valley Exposure Unit (EU) 3. The total area of the EU is approximately 39 acres. The area within EU 3 is bounded by First Street on the west, Central Avenue on the north, Third Street on the east and south. The slab of Building 2523 has been stabilized with a cap of flowable fill concrete and asphalt to contain residual radiological contamination and to provide surface suitable for vehicle parking. No below-grade demolition actions were performed during this task.
A synthetic aperture imaging L-band radar flown aboard the NASA CV-990 remotely sensed a number of ice-covered lakes about 48 km northwest of Bethel, Alaska. The image obtained is a high resolution, two-dimensional representation of the surface backscatter cross section, and large differences in backscatter returns are observed: homogeneous low returns, homogeneous high returns and/or low returns near lake borders, and high returns from central areas. It is suggested that a low return indicates that the lake is frozen completely to the bottom, while a high return indicates the presence of fresh water between the ice cover and the lake bed.
A meteorological overview of the Arctic Boundary Layer Expedition (ABLE 3A) flight series is presented. Synoptic analyses of mid-tropospheric circulation patterns are combined with isentropic back trajectory calculations to describe the long-range (400-3000 km) atmospheric transport mechanisms and pathways of air masses to the Arctic and sub-Arctic regions of North America during July and August 1988. Siberia and the northern Pacific Ocean were found to be the two most likely source areas for 3-day transport to the study areas in Alaska. Transport to the Barrow region was frequently influenced by polar vortices and associated short-wave troughs over the Arctic Ocean, while the Bethel area was most often affected by lows migrating across the Bering Sea and the Gulf of Alaska, as well as ridges of high pressure which built into interior Alaska. July 1988 was warmer and dryer than normal over much of Alaska. As a result, the 1988 Alaska fire season was one of the most active of the past decade. Airborne lidar measurements verified the presence of biomass burning plumes on many flights, often trapped in thin subsidence layer temperature inversions. Several cases of stratosphere/troposphere exchange were noted, based upon potential vorticity analyses and aircraft lidar data, especially in the Barrow region and during transit flights to and from Alaska.
This paper reports CH4 flux to the atmosphere from a variety of tundra environments near Bethel, Alaska during the summer months of 1988. Emissions from wet meadow tundra averaged 144 +/- 31 mg/sq m/d and ranged from 15.6 to 426 mg/sq m/d varying with soil moisture and temperature. Flux from the drier upland tundra was about two orders of magnitude lower and averaged 2.3 +/- 1.1 mg/sq m/d. Tundra lakes emit CH4 from the open water surface as well as from fringing aquatic vegetation; the presence of vegetation significantly enhanced flux over open water rates. Calculated diffusive fluxes from open water varied with lake size, the large lakes emitting 3.8 mg/sq m/d and small lakes emitting an average of 77 mg/sq m/d. An updated estimate of global emissions from tundra indicates an annual fluxes of approximately 11 +/- 3 Tg CH4.
CO2 exchange rates were measured at selected tundra sites near Bethel, Alaska using portable, climate-controlled, instrumented enclosures. The empirically modeled exchange rate for a representative area of vegetated tundra was 1.2 +/- 1.2 g/sq m/d, compared to a tower-measured exchange over the same time period of 1.1 +.0- 1.2 g/sq m/d. Net exchange in response to varying light levels was compared to wet meadow and dry upland tundra, and to the net exchange measured by the micrometeoroidal tower technique. The multispectral reflectance properties of the sites were measured and related to exchange rates in order to provide a quantitative foundation for the use of satellite remote sensing to monitor biosphere/atmosphere CO2 exchange in the tundra biome.
Ozone (O3) and aerosol distributions were remotely measured from an aircraft using a differential absorption lidar (DIAL) system as part of the 1988 NASA Global Tropospheric Experiment - Arctic Boundary Layer Experiment (ABLE-3A). The airborne DIAL system made simultaneous measurements of O3 and aerosols from the surface to above the tropopause. These measurements were made in a broad range of atmospheric conditions over the tundra, ice, and ocean regions near Barrow and Bethel, Alaska, during July and August 1988. The tropospheric composition over the Arctic was found to be strongly influenced by stratospheric intrusions. Regions of low aerosol scattering and enhanced O3 mixing ratios were usually correlated with descending air from the upper troposphere or lower stratosphere. Several cases of enhanced O3 were observed during ABLE-3A in conjunction with enhanced aerosol layers in the free troposphere resulting from biomass burning. As was found in the Amazon, the products of biomass burning can significantly alter O3 concentrations in the troposphere. This paper describes the NASA airborne DIAL system and discusses the large-scale variations of O3 and aerosols observed with the airborne DIAL system during ABLE-3A.
The report provides a compendium of NASA aircraft data that are available from NASA's Global Tropospheric Experiment's (GTE) Arctic Boundary Layer Experiments (ABLE) conducted in July and August of 1988 (ABLE-3A) and 1990 (ABLE-3B). ABLE-3A flight experiments were based at Barrow and Bethel, Alaska, and included survey/transit flights to Thule, Greenland. ABLE-3B flight experiments were based at North Bay (Ontario) and Goose Bay, Canada, and included flights northward to Frobisher Bay, Canada. The primary purposes of the experiments were (1) the measurement of the flux of various trace gases from high-arctic ecosystems, (2) the elucidation of factors important to the production and destruction of ozone, and (3) the documentation of source and chemical signature of air common to and transported into the regions. The report provides a representation, in the form of selected data plots, of aircraft data that are available in archived format via NASA Langley's Distributed Active Archive Center. The archived data bases include data for other species measured on the aircraft as well as numerous supporting data, including meteorological observations/products, results from surface studies, satellite observations, and sondes releases.
At the request of the Alaska Air Carriers Association, researchers from the NASA Aviation Safety Reporting System, at NASA Ames Research Center, conducted a study on aspects of safety in Alaskan Part 135 air taxi operations. An interview form on human factors safety issues was created by a representative team from the FAA-Alaska, NTSB-Alaska, NASAASRS, and representatives of the Alaska Air Carriers Association which was subsequently used in the interviews of pilots and managers. Because of the climate and operational differences, the study was broken into two geographical areas, the southern coastal areas and the northern portion of the state. This presentation addresses the northern area, specifically: Bethel, Fairbanks, Nome, Kotzebue, and Barrow. The interview questions dealt with many of the potential pressures on pilots and managers associated with the daily air taxi operations in Alaska. The impact of the environmental factors such as the lack of available communication, navigation and weather information systems was evaluated. The results of this study will be used by government and industry working in Alaska. These findings will contribute important information on specific Alaska safety issues for eventual incorporation into training materials and policies that will help to assure the safe conduct of air taxi flights in Alaska.
Coastal communities in Alaska are frequently subjected to storm surges that erode shorelines and riverbanks, which increases flood risks around critical village infrastructure. Coastal erosion in western Alaska may be occurring currently at rates as high as 15 m per year, but the region has not been mapped in enough detail to accurately assess recent shoreline and inland riverbank erosion rates. To update the mapping of changes in all of SWAlaska’s coastal margins, Landsat 8 satellite imagery was analyzed to detect trends in the normalized difference water index collected from 2013 to 2023. The normalized difference water index values range from -1 to 1, with negative values indicating majority land that includes soil and live vegetation cover and positive values indicating majority water coverage. Results showed marked coastal shoreline erosion at Chagvan Bay, Hagemeister Island, and Nanvak Bay over the past decade. Additional locations of recent bank erosion were detected on the Kuskokwim River, from its upriver mouth past the city of Bethel. Riverbank erosion was also detected in northern Nushagak Bay, and extensive surface-wetting trends around wetlands and riverbanks were detected near the village of Togiak. Moreover, many villages on the west coast of Alaska and in the Kuskokwim River Delta have recently documented climate change case studies highlighting bank erosion, indicating that a variety of related ecological disturbances are ongoing across the region.
This work introduces automated machine learning workflows that address critical bottlenecks in surrogate model development for Ion Cyclotron Range of Frequencies (ICRF) heating applications. The automated framework includes data analysis tools that transform raw datasets into actionable insights in seconds, replacing weeks of manual exploratory effort and ensuring consistent, reproducible dataset characterization. By integrating advanced hyperparameter optimization (HPO) methods including Bayesian optimization via BoTorch and Tree-structured Parzen Estimators (TPE), the framework significantly reduces model development time from weeks to hours, decreasing computational cost and required expertise, while enabling high-accuracy surrogate models. Compared to traditional hyperparameter scanning (HPS) techniques such as methodical, randomized, and grid searches, HPO methods achieve superior convergence and predictive performance, even when compared to already well-tuned reference models. On NSTX High Harmonic Fast Wave (HHFW) heating datasets, both Random Forest Regressor (RFR) and neural network surrogates demonstrate improved accuracy, achieving R 2 values beyond 0.97 and 0.98, respectively. The results show that while HPO gains are modest for robust architectures like RFR, they become essential for more sensitive models such as neural networks, highlighting the trade-offs across optimization strategies. Through automated workflows that eliminate manual hyperparameter tuning and require minimal ML expertise, this work enables widespread adoption of high-fidelity surrogate models across the fusion community for real-time plasma control, uncertainty quantification, rapid experimental scenario development, and integrated system optimization.
Assembly of biomolecules at solid-water interfaces requires molecules to traverse complex orientation-dependent energy landscapes through processes that are poorly understood, largely due to the dearth of in-situ single molecule measurements and statistical analyses of the rotational dynamics that define directional selection. Emerging capabilities in high-speed atomic force microscopy and machine learning have allowed us to directly determine the orientational energy landscape and observe and quantify the rotational dynamics for protein nanorods on the surface of muscovite mica under a variety of conditions. Comparisons with kinetic Monte Carlo simulations show that the transition rates between adjacent orientation-specific energetic minima can largely be understood through traditional models of in-plane Brownian rotation across a biased energy landscape, with resulting transition rates that are exponential in the energy-barriers between states. However, transitions between more distant angular states are decoupled from barrier height, with jump-size distributions showing a power-law decay that is characteristic of a non-classical Levy-flight random walk, indicating that large jumps are enabled by alternative modes of motion via activated states. The findings provide new insights into the dynamics of biomolecules at solid-liquid interfaces that lead to self-assembly, epitaxial matching and other orientationally anisotropic outcomes and define a general procedure for exploring such dynamics with implications for hybrid biomolecular-inorganic materials design.
The term "in situ processing" has evolved over the last decade to mean both a specific strategy for visualizing and analyzing data and an umbrella term for a processing paradigm. The resulting confusion makes it difficult for visualization and analysis scientists to communicate with each other and with their stakeholders. To address this problem, a group of over 50 experts convened with the goal of standardizing terminology. This paper summarizes their findings and proposes a new terminology for describing in situ systems. An important finding from this group was that in situ systems are best described via multiple, distinct axes: integration type, proximity, access, division of execution, operation controls, and output type. This paper discusses these axes, evaluates existing systems within the axes, and explores how currently used terms relate to the axes.
Studies of lake ice phenology have historically relied on limited in situ data. Relatively few observations exist for ice out and fewer still for ice in, both of which are necessary to determine the temporal extent of ice cover. Satellite data provide an opportunity to better document patterns of ice phenology across landscapes and relate them to the climatological drivers behind changing ice phenology. We developed a model, the Cumulative Sum Method (CSM), that uses daytime and nighttime surface temperature observations from the Moderate Resolution Imaging Spectroradiometer (MODIS) sensor on board the Earth-observing Aqua satellite to approximate ice in (the onset of ice cover) and ice out from training datasets of 13 and 58 Maine lakes, respectively, during the 2002/2003 through 2017/2018 ice seasons. Ice in was signaled by reaching a threshold of cumulative negative degrees following the first day of the season below 0°C. Ice out was signaled by reaching a threshold of cumulative positive degrees following the first day of the year above 0°C. The comparison of observed and remotely sensed ice-in dates showed relative agreement with a correlation coefficient of 0.71 and a mean absolute error (MAE) of 9.8 days. Ice-out approximations had a correlation coefficient of 0.67 and an MAE of 8.8 days. Lakes smaller in surface area and nearer the Atlantic coast had the greatest error in approximation. Application of the CSM to 20 additional lakes in Maine produced a comparable ice-out MAE of 8.9 days. Ice-out model performance was weaker for the warmest years; there was a larger MAE of 12.0 days when the model was applied to the years 2019–2023 for the original 58 lakes. The development of this model, which utilizes daily satellite data, demonstrates the promise of remote sensing for quantifying ice phenology over short, temporal scales, and wider geographic regions than can be observed in situ, and allows exploration of the influence of surface temperature patterns on the process and timing of ice in and ice out.