Search NASA⌕ Search

SEARCH · Search NASA

Results for “Bond Strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Proceedings of the First Annual Symposium for Nondestructive Evaluation of Bond Strength

Quantitative adhesive bond strength measurement has been an issue for over thirty years. Utilization of nonlinear ultrasonic nondestructive evaluation methods has shown more effectiveness than linear methods on adhesive bond analysis, resulting in an increased sensitivity to changes in bondline conditions. Correlation to changes in higher order material properties due to microstructural changes using nonlinear ultrasonics has been shown and could relate to bond strength. Nonlinear ultrasonic energy is an order of magnitude more sensitive than linear ultrasound to these material parameter changes and to acoustic velocity changes caused by the acoustoelastic effect when a bond is prestressed. This increased sensitivity will assist in getting closer to quantitative measurement of adhesive bond strength. Signal correlations between non-linear ultrasonic measurements and initialization of bond failures have been successfully measured. This paper reviews nonlinear bond strength research efforts presented by university and industry experts at the First Annual Symposium for Nondestructive Evaluation of Bond Strength organized by the NDE Sciences Branch at NASA Langley in November 1997.

Roberts, Mark J.↗
NASA NTRS1976

On a model of calculating bond strength

Diffusion bonding is a fabricating process to join the fibers and a matrix together forming a composite. The efficiency of the bonding process depends on temperature, time, and pressure. Based on a simplified pair potential model, an expression for the bond-energy at the fiber-matrix interface is formulated in terms of the above-mentioned three parameters. From this expression and the mean atomic distance, the bond-strength between the fibers and the matrix can be calculated.

Yue, A. S.↗
DOE OSTI2022

Correlation between Interface Microstructure and Bond Strength of Al6061/Al6061 HIP-Bonded Plates for Fuel Cladding Application

The effects of hot isostatic pressing (HIP) processing parameters on microstructure and bond strength of Al6061/Al6061 plate interfaces were systemically investigated at the micro- and nanoscale. The HIP bonding of the two aluminum plates was performed at four temperatures: 350°C, 400°C, 450°C, and 560°C. The results reveal the formation of micron scaled Mg 2 Si precipitate and uniform nano scaled Mg 2 Al 2 O 5 oxide at the interface. The formation of Mg 2 Al 2 O 5 is closely associated with the fast bulk diffusion of Mg from the Al matrix to the amorphous Al 2 O 3 /Al interface and subsequent reaction between Mg and Al 2 O 3 . Finally, the highest and lowest bond strengths were observed in samples HIP bonded at 450°C and 350°C, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tailoring the Selective Oxidation of Hydroxyl-Containing Compounds via Precisely Tuning the Hydrogen-Bond Strength of Catalyst H-Bond Acceptors

The unique performance of the enzyme is mainly achieved via weak interactions between the “outer coordination sphere” and the substrate. Inspired by this process, we developed 3D encapsulated-structure catalysts with hydrogen-bond engineering on the shell, which mimics the “outer coordination sphere” of an enzyme. Various hydrogen bond acceptors (C=O, S=O, and N–O groups) are imparted in the shell. Concentration-dependent 1H NMR, inverse-phase gas Chromatography (IGC) measurements, and DFT calculations underscore that the hydrogen bond strength between the acceptor groups and alcohol follows the order of C=O < S=O < N–O. The hydroxyl compound oxidation rate vs the hydrogen bond strength follows a volcano behavior, reminiscent of Sabatier’s principle. The performance variation among catalysts is attributed to the adsorption strength of the substrate. The proposed bioinspired design principle expands the scope of encapsulated catalysts, enabling fine regulation of catalytic activity through precise microenvironment control via weak interactions with substrates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2000

Nondestructive Determination of Bond Strength

Although many nondestructive techniques have been applied to detect disbonds in adhesive joints, no absolutely reliable nondestructive method has been developed to detect poor adhesion and evaluate the strength of bonded joints prior to the present work which used nonlinear ultrasonic methods to investigate adhesive bond cure conditions. Previously, a variety of linear and nonlinear ultrasonic methods with water coupling had been used to study aluminum-adhesive-aluminum laminates, prepared under different adhesive curing conditions, for possible bond strength determination. Therefore, in the course of this research effort, a variety of finite-amplitude experimental methods which could possibly differentiate various cure conditions were investigated, including normal and oblique incidence approaches based on nonlinear harmonic generation as well as several non-collinear two-wave interaction approaches. Test samples were mechanically scanned in various ways with respect to the focus of a transmitting transducer operated at several variable excitation frequencies and excitation levels. Even when powerful sample-related resonances were exploited by means of a frequency scanning approach, it was very difficult to isolate the nonlinear characteristics of adhesive bonds. However, a multi-frequency multi-power approach was quite successful and reliable. Ultrasonic tone burst signals at increasing power levels, over a wide frequency range, were transmitted through each bond specimen to determine its excitation dependent nonlinear harmonic resonance behavior. Relative amplitude changes were observed particularly in the higher harmonic spectral data and analyzed using a local displacement and strain analysis in the linear approximation. Two analysis approaches of the excitation-dependent data at specific resonances were found to be quite promising. One of these approaches may represent a very robust algorithm for classifying an adhesive bond as being properly cured or not. Another approach, in addition to differentiation between various cure conditions, may even provide information with respect to the bond strength. Several technical papers were published during the course of this research and a summary is presented in the Ph.D. dissertation of Tobias P. Berndt, a graduate student financially supported by this NASA Grant.

Source record↗
NASA NTRSDate not supplied

Measurement System Analysis of a Novel Phase-Based Ultrasonic NDE Technique for Bond Strength Measurement

Fiber reinforced polymer parts have shown tremendous benefits in aerospace structural applications, but their qualification and certification for use in safety critical areas are currently hindered by the lack of a capable non-destructive evaluation (NDE) method or technique for the inspection of these adhesively bonded parts. Conventional NDE methods and techniques typically detect gross bond defects in a qualitative (Pass/Fail) manner. These techniques struggle to detect weak or kissing bonds. Also, there are no widely adopted NDE methods or techniques for measuring interfacial bond strength or detecting kissing bonds. Bond strength is currently ensured by process control and semi-destructive testing. Results from recent research from other authors, including but not limited to mechanical testing, have shown an excellent correlation between interfacial stiffness of an adhesively bonded joint and the adhesive bond strength of that joint. In this paper, a measurement system analysis (MSA) of a novel phase-based ultrasonic NDE Technique, developed at NASA Langley Research Center, is presented for bond strength measurement to assess at an increased level the measurement process and identify components of variation in that measurement process.

Ultrasound↗
NASA NTRS1999

Proceedings of the Second Annual Symposium for Nondestructive Evaluation of Bond Strength

Ultrasonics, microwaves, optically stimulated electron emission (OSEE), and computational chemistry approaches have shown relevance to bond strength determination. Nonlinear ultrasonic nondestructive evaluation methods, however, have shown the most effectiveness over other methods on adhesive bond analysis. Correlation to changes in higher order material properties due to microstructural changes using nonlinear ultrasonics has been shown related to bond strength. Nonlinear ultrasonic energy is an order of magnitude more sensitive than linear ultrasound to these material parameter changes and to acoustic velocity changes caused by the acoustoelastic effect when a bond is prestressed. Signal correlations between non-linear ultrasonic measurements and initialization of bond failures have been measured. This paper reviews bond strength research efforts presented by university and industry experts at the Second Annual Symposium for Nondestructive Evaluation of Bond Strength organized by the NDE Sciences Branch at NASA Langley in November 1998.

Roberts, Mark J.↗
DOE OSTI2025

Experimental Evaluation of Interfacial Bonding Strength Between 304 Stainless Steel Substrate and Electrodeposited Nickel Coating Using Mesoscale Mechanical Testing Methods

Electrodeposition is a commonly used method for depositing a metal layer on a metallic substrate, to provide a decorative finish or for functional purposes including wear and corrosion resistance. The interfacial bonding strength is a critical factor in determining the quality of electrodeposition, as it ensures the adhesion of the deposited layer to the substrate. Despite its importance, there has not previously been a suitable mechanical testing method to quantitatively characterize the bonding strength between the electrodeposited layers and the substrate, due to the high strength of the materials and to restrictions imposed by the geometry (due to the small thickness of the plating layer) to manufacture tensile bars. In this study, we introduce a novel mesoscale mechanical testing method to overcome these limitations. This technique was applied to assess the bonding strength between a 304 stainless steel (SS) substrate and electrodeposited nickel with three different plating formulae (nickel sulfamate, Watts bath, and hard nickel). The thickness of the pure nickel coatings achieved for each of the three electrolyte solutions was approximately 1 mm on each side of the substrate. Mesoscale tensile bars of 1 mm length were manufactured by a femtosecond laser, with the material interface at the center of the gauge section, and then tensile-tested with digital image correlation. Further, the results proved that the electrodeposition technique is able to produce a very high bonding strength that is close to the yield strength of both the substrate material and the electrodeposited nickel layer. Additionally, in the case of the Watts bath formula, the interfacial bonding strength between the SS 304 and electrodeposited nickel can exceed that of the nickel layer. This method is expected to be useful for quantifying the interfacial bonding strength in numerous applications.

36 MATERIALS SCIENCE↗
NASA NTRS2010

An Experimental Investigation of Silicone-to-Metal Bond Strength in Composite Space Docking System Seals

The National Aeronautics and Space Administration (NASA) is currently developing a new universal docking mechanism for future space exploration missions called the Low Impact Docking System (LIDS). A candidate LIDS main interface seal design is a composite assembly of silicone elastomer seals vacuum molded into grooves in an electroless nickel plated aluminum retainer. The strength of the silicone-tometal bond is a critical consideration for the new system, especially due to the presence of small areas of disbond created during the molding process. In the work presented herein, seal-to-retainer bonds of subscale seal specimens with different sizes of intentional disbond were destructively tensile tested. Nominal specimens without intentional disbonds were also tested. Tension was applied either uniformly on the entire seal circumference or locally in one short circumferential length. Bond failure due to uniform tension produced a wide scatter of observable failure modes and measured load-displacement behaviors. Although the preferable failure mode for the seal-to-retainer bond is cohesive failure of the elastomer material, the dominant observed failure mode under the uniform loading condition was found to be the less desirable adhesive failure of the bond in question. The uniform tension case results did not show a correlation between disbond size and bond strength. Localized tension was found to produce failure either as immediate tearing of the elastomer material outside the bond region or as complete peel-out of the seal in one piece. The obtained results represent a valuable benchmark for comparison in the future between adhesion loads under various separation conditions and composite seal bond strength.

Gaier, James R.↗
NASA NTRS1986

Nondestructive evaluation of adhesive bond strength using the stress wave factor technique

Acousto-ultrasonic nondestructive evaluation has been conducted to evaluate the adhesive bond strength between rubber and steel plates using the stress wave factor (SWF) measurement technique. Specimens with different bond strength were manufactured and tested using the SWF technique. Two approaches were used to define the SWF. One approach defines the SWF as the signal energy and the other approach defines the SWF as the square root of the zero moment of the frequency spectrum of the received signal. The strength of the rubber-steel adhesive joint was then evaluated using the destructive peel strength test method. It was observed that in both approaches higher values of the SWF measurements correspond to higher values of the peel strength test data. Therefore, these results show that the stress wave factor technique has the potential of being used in quality assurance of the adhesive bond strength between rubber and steel substrates.

Dos Reis, Henrique L. M.↗
NASA NTRS1990

Measurement of the intrinsic bond strength of brittle thin films on flexible substrates

The brittle cracking and subsequent debonding of nickel films deposited on polymer substrates subjected to uniaxial strain is investigated. Stress analyses for a film/substrate system are performed. Based on the analysis, the interfacial bond strength between brittle thin films and flexible substrates can be evaluated in terms of the tensile strength of the coating and the length of the largest segment that first debonds. Experiments were performed on Ni films with different thicknesses evaporated on polyethylene terephthalate substrates and the intrinsic bond strength was evaluated. The interfacial bond strengths were shown to be relatively independent of the film thickness for the range studied.

Guo, Q.↗
NASA NTRS2012

Carbon Nanotube Bonding Strength Enhancement Using Metal "Wicking" Process

Carbon nanotubes grown from a surface typically have poor bonding strength at the interface. A process has been developed for adding a metal coat to the surface of carbon nano tubes (CNTs) through a wicking process, which could lead to an enhanced bonding strength at the interface. This process involves merging CNTs with indium as a bump-bonding enhancement. Classical capillary theory would not normally allow materials that do not wet carbon or graphite to be drawn into the spacings by capillary action because the contact angle is greater than 90 degrees. However, capillary action can be induced through JPL's ability to fabricate oriented CNT bundles to desired spacings, and through the use of deposition techniques and temperature to control the size and mobility of the liquid metal streams and associated reservoirs. A reflow and plasma cleaning process has also been developed and demonstrated to remove indium oxide, and to obtain smooth coatings on the CNT bundles.

Lamb, James L.↗
DOE OSTI2025

Evaluating the bond strength and fracture mechanisms of cold-sprayed zinc coating on AZ91 magnesium substrate via a combined experimental and computational approach

Magnesium (Mg) alloys are ideal candidates for automotive applications due to their high strength to weight ratio, castability, recyclability etc., however, they lack corrosion and oxidation resistance. Solid-state deposition techniques, such as cold spray, have been demonstrated to enhance their corrosion resistance as it relies on the severe plastic deformation of powder particles upon impact with the substrate to form a metallurgical bond with the substrate and within the coating. At cold sprayed interfaces, a heterogeneous microstructure is formed that includes some porosity, oxides and intermetallics which can significantly affect coating performance. Thus, establishing a direct correlation between the interface microstructure and its properties can aid in designing optimal cold spray parameters. In this study, we investigated the microstructure and mechanical properties of a zinc (Zn) coating deposited on a high pressure die cast (HPDC) AZ91 Mg substrate via high resolution scanning transmission electron microscopy, in situ micro-tensile testing, and finite element method (FEM) modeling. Micro-tensile pillars fabricated using the plasma focused ion beam (PFIB) successfully isolates the coating-substrate interface within the gauge length. The average bond strength of Zn-Mg interface was determined to be ∼140 MPa with failure occurring partially at the interface and mostly into the coatings. A detailed microstructural characterization revealed evidence of a strong metallurgical bonding at the Zn-Mg interface and formation of the C14 MgZn 2 laves phase interlayer resulting in a mixed mode of fracture during the micro-tensile experiments. FEM modeling reveals the stress distribution along the interfaces and suggests that a MgZn 2 layer thickness between 200–400 nm is optimum to increase the bond strength and minimize the triaxiality. Such a site-specific interfacial analysis with correlative computational modeling provides crucial insight into the overall performance of cold spray interfaces.

Bond strength↗
NASA NTRS1988

Fibre-matrix bond strength studies of glass, ceramic, and metal matrix composites

An indentation test technique for compressively loading the ends of individual fibers to produce debonding has been applied to metal, glass, and glass-ceramic matrix composites; bond strength values at debond initiation are calculated using a finite-element model. Results are correlated with composite longitudinal and interlaminar shear behavior for carbon and Nicalon fiber-reinforced glasses and glass-ceramics including the effects of matrix modifications, processing conditions, and high-temperature oxidation embrittlement. The data indicate that significant bonding to improve off-axis and shear properties can be tolerated before the longitudinal behavior becomes brittle. Residual stress and other mechanical bonding effects are important, but improved analyses and multiaxial interfacial failure criteria are needed to adequately interpret bond strength data in terms of composite performance.

Grande, D. H.↗
NASA NTRS1990

Intrinsic bond strength of metal films on polymer substrates

A semiquantitative method for the measurement of the intrinsic bond strength between elastic substrates and elastic films that fail by brittle fracture is described. Measurements on a polyethylene terephthalate (PET)-Ni couple were used to verify the essential features of the analysis. It was found that the interfacial shear strength of Ni on PET doubled after ion etching.

Wheeler, Donald R.↗