Search NASA⌕ Search

SEARCH · Search NASA

Results for “Bonded magnets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Traction Motor Design Trade-Offs with Additively Manufactured Anisotropic Bonded Magnets

Extrusion based big area additive manufacturing (BAAM) has been previously demonstrated for the fabrication of dense anisotropic bonded magnets. This paper reports on design trade-offs when such magnets are employed in a motor designed for electric vehicle applications. An external rotor fractional slot permanent magnet synchronous machine designed with sintered dysprosium free magnets rated for 100kW peak and 50kW continuous power is used as the baseline. The impact of using the bonded BAAM magnets on the motor and inverter volumes, motor loss and cooling systems as well as demagnetization margins is evaluated. It is found that although the motor power density reduces due to the lower energy product of the BAAM magnets, there are other system level benefits including reductions in the cooling system requirement, lower inverter rating and volume, decrease in short circuit current and improved demagnetization marains.

additive manufacturing↗
DOE OSTI2021

Alignment of magnetic particles in anisotropic Nd–Fe–B bonded magnets

High-performance anisotropic bonded magnets need a high volumetric filling fraction of magnetic powder in a polymer binder and good alignment while possessing adequate mechanical properties. The correlation between the degree of alignment (DOA) and the volumetric filling fraction of magnetic powder, the type of binder and the processing parameters have been studied using Nd–Fe–B anisotropic bonded magnets. Here, thermomagnetic analysis and differential scanning calorimetry results show that the magnetic powder can be well aligned in a bonded magnet under an external magnetic field at a temperature higher than the binders' melting point by 20–60 K, depending on the type of magnetic powder and binder. The DOA results mainly from the interplay between the Zeeman energy (E app ) and the inter-particle static energy (E stat ) in bonded magnets at the chosen alignment temperature and the magnetic fields. A good alignment can be achieved by an alignment magnetic field which is about twice its coercivity in an anisotropic Nd–Fe–B bonded magnet, which is confirmed by our experimental and modeling results.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Challenges in Postprocessing of Hybrid Manufacturing of Magnet Polymer Composites to Enhance the Energy Product of NdFeB Bonded Magnets

Bonded permanent magnets need to process magnetic filler particles and binder together which is a form of hybrid or composite manufacturing that needs to simultaneously process multimaterials. Polymer bonding of the permanent magnets decreases the energy product of the bonded magnets which varies with square of loading fraction of magnetic materials. However, due to high viscosity of bonding polymer prohibits loading higher than 80 volume % of magnetic materials in most efficient loading process such as compression molding. To further increase the loading of magnetic fraction in the bonded permanent magnets, it is expected to be beneficial to introduce a fraction of nonreacting thermally sacrificial polymer along with permanent bonding polymer in the least permissible of about 20 volume % of the polymer. This process of first adding the sacrificial polymer for higher processability for composites and later removing it via post processing such as heat treatment provides a simple example of inclusion of both the additive and the subtractive stages of hybrid manufacturing. These hybrid composite magnets can be heat treated to remove the sacrificial polymer to further increase the density and energy product which might require to implement hot isostatic pressing for compaction. Although the identification of such ideal polymer requires an extensive polymer chemistry research, we have compression molded several permanent bonding polymers such as nylon, polycarbonate (PC) and polyphenyl sulfide (PPS) and potential sacrificial polymer such as polyoxymethylene (POM), polystyrene (PS), and Acrylonitrile Butadiene Styrene (ABS) and heat treated to remove the sacrificial polymers. It is discovered that oxygen free low temperature pyrolizable polymers could be the potential candidates for increasing the magnet particles loading for achieving high energy products.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Bi-modal particle size distribution for high energy product hybrid Nd–Fe–B—Sm–Fe–N bonded magnets

In this work, we have demonstrated high energy product bonded magnet by leveraging the variation in sizes between Nd-Fe-B and Sm-Fe-N, as well as their hard magnetic properties. The hybrid anisotropic bonded magnets contain 70 vol% of magnet powder (Dy-free Nd-Fe-B and Sm-Fe-N) and 30 vol% of nylon. The objective of the work was to create bi-modal and bi-compositional bonded magnets in which the fine (3μm) particles of Sm-Fe-N would be used to fill the voids between the bigger Nd-Fe-B (105μm) particles, thus improve packing density. The magnetic hysteresis loop did not show significant signs of decoupled interactions between the magnetic phases. It was also found that the performance of the bonded magnet was most enhanced at 1:4 ratio of Nd-Fe-B and Sm-Fe-N. At that ratio, maximum density of 5 g/cm 3 and the highest (BH) max value of 18.5 MGOe were obtained, although the intrinsic coercivity decreased, relative to the trend seen for other ratios. This work advances the opportunity to expand the use of Sm-Fe-N in bonded magnet applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Thermal stability of anisotropic bonded magnets prepared by additive manufacturing

Abstract In this research, anisotropic NdFeB + SmFeN hybrid and NdFeB bonded magnets are additively printed in a polyphenylene sulfide (PPS) polymer binder. Printed NdFeB + SmFeN PPS bonded magnets displayed excellent magnetic properties ( B r [remanence] = 6.9 kG [0.69 T], H cj [coercivity] = 8.3 kOe [660 kA/m], and BH max [energy product] = 9.9 MGOe [79 kJ/m 3 ]) with superior corrosion resistance and thermal stability. The anisotropic NdFeB bonded magnet shows a high coercivity of 14.6 kOe (1162 kA/m) with a BH max of 8.7 MGOe (69 kJ/m 3 ). The coercivity and remanence temperature coefficients for NdFeB + SmFeN hybrid bonded magnets are −0.10%/K and −0.46%/K, and for NdFeB bonded magnets are −0.14%/K and −0.53%/K in the range of 300–400 K, indicating that the hybrid bonded magnets are thermally stable. The average flux aging loss for hybrid magnets was also determined to be very stable over 2000 h at 448 K (175°C) in air with 2.04% compared to that of NdFeB magnets with 3.62%.

thermal stability↗
DOE OSTI2026

Correlation of coercivity, microstructure, and surface defects in HDDR-processed Nd-Fe-B powders for bonded magnet applications

Hydrogenation-Disproportionation-Desorption-Recombination (HDDR) is an effective method for producing high coercivity, anisotropic powder from either fresh Nd-Fe-B alloy or recycled Nd-Fe-B magnets for use in bonded magnets. We investigated the impact of surface defects on the coercivity of HDDR-processed Nd-Fe-B using scanning electron microscopy (SEM), magnetic measurements, and micromagnetic simulations. We observed that coercivity decreases as particle size reduces, with SEM revealing surface defects and the detachment of Nd 2 Fe 14 B grains and Nd-rich phases from the particle surface. Micromagnetic simulations indicate that demagnetization initiates at the particle surface, where these defects are most concentrated, leading to reduced coercivity. The reduction in squareness of demagnetization curve, knee point field and coercivity for smaller HDDR particles is attributed to an increased specific surface area, which exhibits reduced nucleation field and weak domain wall pinning field during magnetization reversal. By addressing the role of surface defects in coercivity degradation, this study provides insights for improving both new powder production and recycling strategies, ultimately leading to enhanced performance of bonded magnets and contributing to more sustainable practices in the rare earth supply chain. One potential strategy to enhance the performance of HDDR Nd-Fe-B materials involves reducing the fraction of fine particles ($<$35 µm) and promoting the formation of grain boundary phases on particle surfaces.

Liu, Xubo B. [Ames Laboratory (AMES), Ames, IA (Un↗
DOE OSTI2024

Recycling of additively printed anisotropic Nd-Fe-B bonded magnets

A high potential cost-effective and environmentally friendly method has been applied for recycling anisotropic Nd-Fe-B bonded magnets. Waste additively printed Hydrogenation-Disproportionation-Desorption-Recombination (HDDR) Nd-Fe-B anisotropic bonded magnet was pulverized into composite powder containing Nd-Fe-B particles and nylon binder through cryomilling at a liquid nitrogen temperature (~77 K) under Ar inert atmosphere. Then, the cryomilled composite powder was warm compacted into a bonded magnet. Further, the magnetic particles were aligned during post-compaction annealing under a magnetic field of 30 kOe. The recycled bonded magnets have a higher density (3% enhancement), but slightly inferior magnetic properties compared to the original magnets, i.e., the magnetic remanence, coercivity and maximum energy product are reduced by 2%, 3% and 8%, respectively. The scanning electron microscopy revealed that some HDDR Nd-Fe-B powder crumbled into fine particles during cryomilling. Powder X-ray diffraction showed a small amount of Nd-oxide impurity in the cryomilled powder. The slightly deteriorated magnetic properties are ascribed to the oxidation of Nd-Fe-B particles due to formation of fresh fracture surface during cryomilling. The approach enables the direct reuse of end-of-life bonded magnets in an economical and environmentally friendly way.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Additive manufacturing of highly dense anisotropic Nd–Fe–B bonded magnets

Extrusion based big area additive manufacturing process is utilized for fabrication of dense anisotropic bonded magnets. High loading fraction (≥70 vol%) of magnequench anisotropic Nd–Fe–B powder in nylon is used for preparing anisotropic bonded magnets. A higher energy product of ~143.2 kJ/m 3 is obtained for the post printed magnetic field aligned at 1 Tesla. These findings make an important step towards the fabrication of gap magnets with energy product between ferrite and Nd–Fe–B sintered magnets. Finally, printed bonded magnets exhibited better thermal stability, mechanical properties and superior magnetic properties compared to commercial injection molded magnets.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In-situ magnetic alignment model for additive manufacturing of anisotropic bonded magnets

In this work, we report a mathematical framework which predicts the degree of alignment (DoA) in an in-situ aligned additively manufactured 3D printed bonded magnets. A multiphysics model is developed which couples the harmonious interactions of magnetic particles in a viscous flowing polymer under the presence of an external magnetic field. The hydrodynamic fluid-particle interaction is paired with the magnetophoretic force to predict the particle trajectory and distribution during extrusion through a 3D printer nozzle. Succeeding the force balance, a magnetohydrodynamic torque equilibrium analysis is performed to predict the net-orientation of the magnetic particles as a function of the applied field strength, viscous forces, and particle-to-particle interactions (P2P). Experimental validation of the DoA predictions is performed using 65 vol% Nd-Fe-B+Sm-Fe-N in Nylon12 (DoA exp = 0.620 and DoA theory = 0.686) and 15 vol% Sm-Co in PLA (DoA exp = 0.830 and DoA theory = 0.863). A parametric analysis is performed to analyze the effect of operating and design parameters like alignment field strength, magnetic loading fraction, extrusion load, and particle size. The model predicts a competing behavior between particle-fluid and particle-particle interactions under the presence of an applied field. Lastly, the model provides a framework to efficiently predict the DoA in tandem with a functionalized-magnetic 3D printer and allows the user to adjust the operating parameters according to the desired DoA.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Coercivity of (Fe 0.7 Co 0.3 ) 2 B Nanowire and Its Bonded Magnet

(Fe 0.7 Co 0.3 ) 2 B are potential permanent magnets material due to its large saturation magnetization and high Curie temperature. However, it has moderate magnetocrystalline anisotropy (MCA) and low coercivity. One way to improve its coercivity is to combine the contributions from magnetocrystalline- and magnetic-shape anisotropy by preparing (Fe 0.7 Co 0.3 ) 2 B nanowires. We study the effects of size, morphology, and surface defects on the hard magnetic properties of nanowires using micromagnetic simulation. The hard magnetic properties of (Fe 0.7 Co 0.3 ) 2 B nanowire-bonded magnets are estimated, including the role of inter-wire magnetostatic interaction. By considering the existence of local reductions in MCA energy of up to 30% on the surface layer of nanowires, the anisotropic bonded magnet with a 65% vol. of (Fe 0.7 Co 0.3 ) 2 B nanowires would have typical remanence, B r = 7.6–8.4 kG, coercivity, H ci = 9.6–9.9 kOe, and maximum energy product, (BH) m = 14–17.8 MGOe. Developing effective technology for synthesizing nanowires and fabricating corresponding bonded magnets is promising for manufacturing practical magnets based on the magnetic phase with a relatively low or moderate MCA, such as (Fe 0.7 Co 0.3 ) 2 B.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Compression molding of anisotropic NdFeB bonded magnets in a polycarbonate matrix

Anisotropic bonded Nd 2 Fe 14 B (NdFeB) magnets in a polycarbonate (PC) binder matrix are fabricated using a compression molding process. The weight fractions (w.f.) of NdFeB in PC on the batch mixer are 20, 50, 75, 85 and 95% compared to the twin screw extruder with 20, 50 and 75% respectively. The density of the 95% batch mixed magnets fabricated was 5.34 g/cm 3 and the magnetic properties are, intrinsic coercivity H ci = 942.99 kA/m, remanence B r = 0.86 T, and energy product (BH) max = 120.96 kJ/m 3 . Furthermore, the measured tensile properties are in the range of 27-59 MPa, comparable to that of polyamide (PA), polyphenylene sulfide (PPS) bonded magnets and demonstrating potential for bonded magnet applications. Scanning electron microscopy showed that the onset of failure occurs in the magnetic particle- matrix interface. This study demonstrates that compression additive molding technique can be used to fabricate high performance NdFeB polycarbonate composite magnets with improved mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Material extrusion with integrated compression molding of NdFeB/SmFeN nylon bonded magnets using small- and large-scale pellet-based 3D-printers

High-density bonded rare-earth magnets are manufactured using pellet-fed additive manufacturing (AM)/material extrusion and an integrated additive manufacturing-compression molding (AM-CM) process. Neodymium iron boron – samarium iron nitride in polyamide 12 (NdFeB-SmFeN/PA12) of 93 % weight fraction (65 % volume fraction) are used for the study. The mechanical properties (tensile strength and modulus), magnetic properties (maximum energy density, coercivity, remanence) are reported. Manufacturing parameters such as layer height, barrel temperatures, screw speed and gantry feed rate are optimized to obtain the highest possible density of the magnets using a small-scale desktop material extrusion printer. Large scale integrated additive manufacturing-compression molding (AM-CM) is then utilized to increase the density of the magnets by reducing porosity defects common in the material extrusion process. The density of as-printed magnets was 5.2 g/cm 3 with a BH max value of 124.14 kJ/m 3 , tensile strength of 20 MPa and a modulus of 2 GPa. AM-CM increased the density of the compound by 5.5 % (5.49 g/cm 3 ). The reduction in porosity was confirmed using X-ray tomography (XCT). Improvement in mechanical strength of the material was also observed, with an increase in tensile strength of 25 % (25.09 MPa) and increase in tensile modulus of 275 % (5.49 GPa). Scanning electron microscopy showed increased particle-matrix adhesion with the integrated AM-CM process.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Indirect additive manufacturing process for fabricating bonded soft magnets

A bonded soft magnet object comprising bonded soft magnetic particles of an iron-containing alloy having a soft magnet characteristic, wherein the bonded soft magnetic particles have a particle size of at least 200 nm and up to 100 microns. Also described herein is a method for producing the bonded soft magnet by indirect additive manufacturing (IAM), such as by: (i) producing a soft magnet preform by bonding soft magnetic particles with an organic binder, wherein the magnetic particles have an iron-containing alloy composition with a soft magnet characteristic, and wherein the particles of the soft magnet material have a particle size of at least 200 nm and up to 100 microns; (ii) subjecting the preform to an elevated temperature sufficient to remove the organic binder to produce a binder-free preform; and (iii) sintering the binder-free preform at a further elevated temperature to produce the bonded soft magnet.

Paranthaman, Mariappan Parans↗