Search NASA⌕ Search

SEARCH · Search NASA

Results for “CARBON DIOXIDE LASERS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Laser-Induced Plasma as a Method for the Metallic Materials Hardness Estimation: An Alternative Approach

The application of an alternative laser-induced breakdown spectroscopy (LIBS) method based on transversely excited atmospheric (TEA) CO2 laser was investigated for the first time for estimating the hardness of metallic materials. The human eye-safe (TEA) CO2 laser, operating at 10.6 µm, was used for plasma generation. The LIBS spectra were recorded by employing a cost-effective CCD camera for the time-integrated and spatial resolved measurements. The cast iron and aluminum alloys samples with different hardness have been tested. The ratio between the magnesium ionic and neutral lines in LIBS spectra was applied for estimating the material hardness. In addition, the hardness of all samples included in this study was determined using the conventional method for material hardness determination, i.e. Vickers hardness test. The linear dependence of magnesium lines intensity ratio on the sample’s hardness was obtained for both kinds of materials. Profilometric measurements were used to verify that the newly-introduced method is almost nondestructive for the investigated metals. The results obtained in the present work confirmed the potential of using this original LIBS system not only for the fast elemental analysis but also for the direct estimation of the hardness of metals and alloys. © 2020, Springer Science+Business Media, LLC, part of Springer Nature.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Laser‐Sintered Silver Metallization for Silicon Heterojunction Photovoltaic Cells

Herein, a novel metallization technique is reported for crystalline silicon heterojunction (SHJ) solar cells in which silver (Ag) fingers are printed on the SHJ substrates by dispensing Ag nanoparticle‐based inks through a needle and then sintered with a continuous‐wave carbon dioxide (CO 2 ) laser. The impact of the Ag ink viscosity on the line quality and the line resistance is investigated on three Ag inks with different viscosities. Increasing ink viscosity yields higher Ag contact heights, larger aspect ratios, and lower line resistance values. The Ag line height increases from less than a micrometer to ≈18.62 ± 3.48 μm with the increasing viscosity. Photoluminescence imaging shows that the low‐resistance Ag metal contacts obtained do not result in any passivation damage of the SHJ substrate. This is because the wavelength of light emitted from the CO 2 laser (i.e., 10.6 μm) leads to optical absorption in the Ag, but this light is effectively transparent to the transparent conductive oxide film, amorphous silicon films, and crystalline silicon substrate. Bulk resistivity values as low as 6.5 μΩ cm are obtained for the laser‐sintered Ag contact and printed using the Ag ink with the highest viscosity in this work.

Mousumi, Jannatul Ferdous↗
DOE OSTI2021

MiniCarb: a passive, occultation-viewing, 6U CubeSat for observations of CO 2 , CH 4 , and H 2 O

In this report we present the final design, environmental testing, and launch history of MiniCarb, a 6U CubeSat developed through a partnership between NASA Goddard Space Flight Center and Lawrence Livermore National Laboratory. MiniCarb’s science payload, developed at Goddard, was an occultation-viewing, passive laser heterodyne radiometer for observing methane, carbon dioxide, and water vapor in Earth’s atmosphere at ~1.6 µm s -1 . MiniCarb’s satellite, developed at Livermore, implemented their CubeSat Next Generation Bus plug-and-play architecture to produce a modular platform that could be tailored to a range of science payloads. Following the launch on 5 December 2019, MiniCarb traveled to the International Space Station and was set into orbit on 1 February 2020 via Northrop Grumman’s Cygnus capsule which deployed MiniCarb with tipoff rotation of about 20° s (significantly higher than the typical rate of 3° s -1 from prior CubeSats), from which the attitude control system was unable to recover resulting in a loss of power. In spite of this early failure, MiniCarb had many successes including rigorous environmental testing, successful deployment of its solar panels, and a successful test of the radio and communication through the Iridium network. This prior work and enticing cost (approximately $\$2$ M for the satellite and $\$$250 K for the payload) makes MiniCarb an ideal candidate for a low-cost and rapid rebuild as a single orbiter or constellation to globally observe key greenhouse gases.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Cost of Using Laser Powder Bed Fusion to Fabricate a Molten Salt-to-Supercritial Carbon Dioxide Heat Exchanger for Concentrating Solar Power

Advances in manufacturing technologies and materials are crucial to the commercial deployment of energy technologies. We present the case of concentrating solar power (CSP) with molten salt (MS) thermal storage, where low-cost, high-efficiency heat exchangers (HXs) are needed to achieve cost competitiveness. Here, the materials required to tolerate the extreme operating conditions in CSP systems make it difficult or infeasible to produce them using conventional manufacturing processes. Although it is technically possible to produce HXs with adequate performance using additive manufacturing, specifically laser powder bed fusion (LPBF), here we assess whether doing so is cost-effective. We describe a process-based cost model (PBCM) to estimate the cost of fabricating a MS-to-supercritical carbon dioxide HX using LPBF. The PBCM is designed to identify modifications to designs, process choices, and manufacturing innovations that have the greatest effect on manufacturing cost. Our PBCM identified HX design and LPBF process modifications that reduced projected HX cost from $\$750$ per kilo-Watt thermal (kW-th) ($\$8$ /cm 3 ) to $\$350$ /kW-th ($\$6/$ cm 3 ) using currently available LPBF technology, and down to $\$220$ /kW-th ($\$4$ /cm 3 ) with improvements in LPBF technology that are likely to be achieved in the near term. The PBCM also informed a redesign of the HX design that reduced projected costs to $\$140$ –160/kW-th ($\$3$ /cm 3 ).

36 MATERIALS SCIENCE↗
DOE OSTI2021

Laser-induced fluorescence thermometry of supercritical CO 2 flows inside a micro-channel

This work demonstrates a thermometric technique using laser-induced fluorescence (LIF) in supercritical carbon dioxide flows in a micro-channel. Rhodamine 6G was used as a temperature-sensitive fluorescent dye. The flow conditions were at a pressure of 7.9 MPa and temperature in the range of 23°–90°C. 2D spatial distributions and time-resolved temperature profiles were obtained at this high pressure. Measured LIF signals showed close relations to the temperatures obtained from resistance temperature detectors.

Park, Suhyeon↗
DOE OSTI2020

KCMP Minnesota Tall Tower Carbon Dioxide Data 2007-2019

This data set contains carbon dioxide concentration values and supporting metadata information measured at a tall tower (KCMP radio station, 244 meters) site near St. Paul, Minnesota, USA. The data package includes a text file containing hourly continuous carbon dioxide concentration measurements from 2007 to 2019, including raw, de-spiked, and gap filled data. Carbon dioxide concentrations were measured at approximately 100 meters using tunable diode laser spectroscopy. The instrumentation was maintained at the base of the tall tower in a temperature-controlled building. This data was collected to track and improve the understanding of carbon dioxide levels over a twelve year period for the region.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

In-situ synthesis of oxides by reactive process atmospheres during L-PBF of stainless steel

Traditionally, reactive gases such as oxygen (O 2 ) and carbon dioxide (CO 2 ) have been avoided during laser powder bed fusion (L-PBF) of metals and alloys based on the notion that it may lead to defect formation and poor properties. Here, in this work, we show that instead, these gases can be used to form sub-μm-sized oxide particles in-situ during the L-PBF process in an Fe-Cr-Al-Ti stainless steel and lead to improved room temperature and high-temperature mechanical properties. We manufactured cube samples using pure Ar and various reactive gas atmospheres, namely an O 2 /Argon (Ar) mixture containing 0.2 % O 2 and CO 2 /Ar mixtures containing up to 100 % CO 2 . Co-axial measurements of infrared radiation emitted from the melt pool showed correlation to the presence of O 2 or CO 2 in the gas mixture. Builds produced under CO 2 -containing atmosphere contained complex oxides with an average diameter of ~40 nm, an Al-rich core and a Ti-rich shell. Due to the high cooling rates typical to L-PBF, agglomeration of oxides and slag formation on the surface of the samples could almost be entirely avoided. Compression tests at temperatures up to 800 °C showed that the samples produced in 100 % CO 2 have about 20 % higher yield stress compared to samples produced in Ar. The paper concludes with a discussion of the formation mechanism of the observed oxides. Our results show that in-situ reactions during additive manufacturing processes are a promising pathway to the synthesis of particle-reinforced alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Photodissociation and Infrared Spectroscopy of U + (CO 2 ) n , UO + (CO 2 ) n , and UO 2+ (CO 2 ) n Cation-Molecular Complexes

Laser vaporization of uranium in a pulsed supersonic expansion of carbon dioxide is used to produce complexes of the form U + (CO 2 ) n , UO + (CO 2 ) n , and UO 2+ (CO 2 ) n . These ions are selected in a reflectron time-offlight mass spectrometer and studied with visible laser photodissociation and tunable infrared laser photodissociation spectroscopy in the region of the CO 2 antisymmetric stretch. The dissociation patterns and spectroscopy of these ions indicate that CO 2 ligands are intact molecules. Although reaction products that form oxide-carbonyl or oxalate species are predicted to be stable, there is no direct evidence in the frequency range studied for the formation of these species. There is no clear indication for the coordination numbers for singly charged uranium and its oxide complexes with CO 2 . However, there is strong support in the vibrational patterns for an eight-coordinate complex of the doubly charged UO 2+ species, i.e., UO 2+ (CO 2 ) 8 .

Cluster chemistry↗
DOE OSTI2021

Additively Manufactured Compliant Hybrid Gas Thrust Bearing for Supercritical Carbon Dioxide Turbomachinery: Design and Proof of Concept Testing

The following paper presents a new type of gas lubricated thrust bearing that utilizes additive manufacturing or also known as direct metal laser melting (DMLM) to fabricate the bearing. The motivation for the new bearing concept is derived from the need for highly efficient supercritical carbon dioxide (sCO2) turbomachinery in the mega-watt power range. The paper provides a review of existing gas thrust-bearing technology, outlines the need for the new DMLM concept, and discusses proof-of-concept testing results. The new concept combines hydrostatic pressurization with individual tilting pads that are flexibly mounted using hermetic squeeze film dampers (HSFD) in the bearing-pad support. This paper describes the thrust-bearing concept and discusses the final design approach. Proof-of-concept testing in air for a 6.8 in. (173 mm) outer diameter thrust gas bearing was performed; with thrust loading, up to 1500 lbs (6.67 kN) and a thrust runner speed of 10krpm (91 m/s tip speed). The experiments were performed with a bent shaft resulting in thrust runner axial vibration magnitudes of 2.9 mils (74 μm) p-p and dynamic thrust loads of 270 lbs (1.2 kN) p-p. In addition, force deflection characteristics and stiffness coefficients of the bearing system are presented for an inlet hydrostatic pressure of 380 psi (2.62 MPa). Results at 10 krpm show that the pad support architecture was able to sustain high levels of dynamic misalignment equaling 6 times the nominal film clearance while demonstrating a unit load-carrying capacity of 55 psi (0.34 Mpa). Gas-film force deflection tests portrayed nonlinear behavior like a hardening spring, while the bearing pad support stiffness was measured to be linear and independent of gas film thickness.

Engineering↗
DOE OSTI2025

An alternative method of changing the pulse duration in a stretcher-compressor pair by changing the gas pressure in the compressor

The relatively narrow bandwidth of neodymium glass requires a much larger stretch ratio of chirped-pulse amplification (CPA) systems. This factor, together with a large incident angle on the gratings, makes glass CPA systems extremely sensitive to the refractive index of the medium in the stretcher-compressor. High sensitivity of the stretcher-compressor pair for hybrid optical parametric chirped-pulse amplification and an Nd:glass laser to the refractive index was demonstrated in air, vacuum, and carbon dioxide, and a pulse duration close to the transform limit was reached. An alternative way to change the pulse duration was proposed. The pulse duration from the best compression of 500 fs to 30 ps was smoothly varied by changing the air pressure from 10 -6 Torr to 1 atm in the compressor and up to 52 ps in carbon dioxide, while the stretcher and compressor remained untouched. Finally, excellent agreement of the measured pulse duration with theoretical calculations was demonstrated.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

An Experimental Investigation of Supercritical Methane Injection Characteristics in a CO2 Environment

Abstract Clean energy generation is gaining significant attention from industries, academia, and governments across the globe. The Allam cycle is one such technology that has been under focus due to its efficiency, environmental friendliness, and economics. This is a direct-fired cycle operating at supercritical conditions using carbon dioxide as a working fluid. Fuel or oxidizer jet mixing with CO2 is a vital phenomenon that governs combustion efficiency, and it is not well understood for the Allam cycle conditions. This paper experimentally investigated the jet characteristics of a methane jet injected into a subcritical to supercritical carbon dioxide environment. A wide range of injection pressures and temperatures were targeted between subcritical to supercritical conditions. Unlike previous studies, the current work focused on injecting lower-density (methane) jets into higher-density (carbon dioxide) environments. Schlieren imaging and methane absorption measurements were simultaneously performed with a CMOS high-speed camera and a 3.39 μm infrared laser. Specifically, we looked at the classical injection parameter of jet spreading angle, which was classically established to be mainly a density ratio function. Here, the jet cone angle was obtained from the postprocessed schlieren imaging. The jet cone angle is a critical characteristic parameter that describes the entrainment rate in a jet; thus, it is a crucial parameter in understanding the nature of the jet. The laser measurements were only used as an additional check to confirm the entry time of methane into the chamber filled with carbon dioxide. Notably, this paper makes a detailed comparison between the jet cone angles of jets with a density ratio. The result showed that the classical correlations, such as Abramovich's theory applied to submerged turbulent gas jets developed for low-density ratio jets, were unsuitable for higher-density ratio jets. It was also observed that the divergence angles were dependent not only on density ratio but also on other parameters such as pressure ratios and reduced pressures.

Engineering↗
DOE OSTI2024

Additively Manufactured Molten Salt to Supercritical Carbon Dioxide Heat Exchanger

Design, fabrication, and experimental characterization of the performance of a molten salt (MS)-to-supercritical carbon dioxide (sCO 2 ) heat exchanger (HE) for concentrating solar power (CSP) applications using laser powder bed fusion (LPBF) additive manufacturing (AM) of nickel-based superalloys is presented in this report. The hypothesis is that such additively manufactured HEs will result in a monolithic, compact, low-pressure drop HE that is durable under cyclic operation at high temperature and high pressure in a corrosive salt environment. Two nickel-based superalloys were considered in the project- Haynes 230 (H230) and Haynes 282 (H282). Process windows for LPBF AM were established to provide dense low porosity parts for both alloys. Creep tests results on heat treated AM H230 and H282 samples showed that the AM fabricated specimens were as robust as the wrought specimens and showed no deficit in creep strength at high temperatures. Haynes 282 was down selected for the HE fabrication based on better dimensional tolerance, better corrosion resistance to chloride salt, and higher creep strength.

14 SOLAR ENERGY↗
DOE OSTI2025

Enhanced Carbon Dioxide Uptake in Drilled Hollow Core Fibers for Raman Spectroscopy

Fiber-based Raman spectroscopy enhances the Raman signal by maximizing the overlap of the optical field and the gas species. However, filling the hollow-core fiber (HCF) with gas requires time that is dependent on the fiber core diameter, fiber length, and pressure of the gas. At ambient pressure, the fiber gas uptake is driven by diffusion into the fiber ends, severely limiting the response time of the system. By laser drilling access holes to the core along the length of the fiber, the uptake time of the gas is reduced, improving the system response time. In this work, we study the carbon dioxide (CO 2 ) sensor dynamics based on Raman signal intensity generated in HCFs. The signal intensity versus gas concentration is characterized by controlling the CO 2 concentration in the surrounding environment of the fiber. Next, we characterize the gas uptake time in HCFs as a function of fiber length. Finally, we optimize the access hole configuration along the fiber, demonstrating reduced sensor uptake time by a factor of three.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Effect of CO{sub 2}-laser power density on the absorption coefficient of polycrystalline CVD diamonds

The effect of 1-s irradiation of an uncooled polycrystalline CVD diamond plate by a focused cw CO{sub 2} laser beam with a power density of 300 – 800 kW cm{sup −2} is investigated. The absorption coefficient of the sample at a power density of 800 kW cm{sup −2} is found to be 0.035 cm{sup −1} larger as compared with that at 300 kW cm{sup −2}, which is related to the temperature dependence of its phonon-induced absorption with a change in temperature from 44 to 100 °C. It is shown that polycrystalline diamond, in contrast to other optical materials, does not exhibit nonlinear (avalanche-like) rise in absorption at high CO{sub 2}-laser power densities, at least up to 800 kW cm{sup −2}. (paper)

36 MATERIALS SCIENCE↗
DOE OSTI2021

Additively Manufactured Compliant Hybrid Gas Thrust Bearing for Supercritical Carbon Dioxide Turbomachinery: Experimental Evaluation and Fluid–Structure Model Predictions

This paper presents rotating test results and advances an analytical predictive fluid–structure model for a new type of gas-lubricated thrust bearing fabricated using direct metal laser melting. The bearing concept in this study is a compliant hybrid gas thrust bearing that uses external pressurization to increase load carrying capacity, where the testing campaign in this study was only focused on steady-state static performance. The need for the bearing concept comes from enabling highly efficient supercritical carbon dioxide (sCO2) turbomachinery by replacing oil-lubricated bearings with process gas lubrication. Leveraging the process gas of the turbomachine for bearing lubrication results in lowered bearing power loss, simplified mechanical design, and allows for novel oil-free hermetic drivetrains resulting in an efficient emission-free system. The new concept utilizes hydrostatic pressurization on individual tilting pads flexibly mounted with hermetic squeeze film dampers (HSFDs). This paper focuses on rotating tests of a 173 mm outer diameter gas thrust bearing in air up to 10 krpm and hydrostatic inlet pressures to 365 psi (2.52 MPa). The influence of thrust runner speed and bearing inlet pressure on force deflection characteristics and load carrying capability of the gas film were experimentally evaluated. This work also advances a predictive fluid–structure thrust bearing model using an isothermal ideal-gas-based compressible Reynolds flow equation directly coupled to a lumped stiffness element possessing axial and rotational degrees-of-freedom. The rotating testing demonstrated load capability of 1816 lbs (8.1 kN), which equates to a thrust bearing unit load of 67 psi (0.46 MPa). Gas film force–deflection curves reveal a nonlinear relationship between thrust load and film clearance. Comparison of film thickness values with the predictive model show good agreement under high load and inlet pressure, however deviate as load and pressure decrease. Load capability was shown to increase with increasing hydrostatic inlet pressure, while the increase in thrust runner speed revealed a small decrease in load capacity.

Engineering↗
DOE OSTI2025

A formaldehyde and nitrogen dioxide toxics monitor for environmental justice

DOE’s Integrated Field Laboratories (IFLs) require a vast array of measurements to measure urban air quality. Nitrogen dioxide (NO2) and formaldehyde (HCHO) are ubiquitous pollutants with numerous sources, most notably vehicle exhaust. High-spatial density measurements are critical to understanding how certain neighborhoods are more adversely impacted by pollutants. This report describes the results of a Phase I SBIR project to develop and demonstrate a rapid, affordable, low-power monitor to provide high spatial resolution mobile measurements of formaldehyde and nitrogen dioxide at street-level, where people live and walk. The spatial density will be achieved via rapid measurements on a mobile platform. This sensor will quantify spatial disparities in cities of the toxics, HCHO and NO2, as well as carbon monoxide and carbon dioxide for better source identification. These species are detected in the mid infrared by laser absorption spectroscopy, and fiberoptics are used. Tasks accomplished include identification and testing of the appropriate spectroscopic regions; coupling of laser light into a fiberoptic system; development of software to control miniature electronics to scan and control two lasers simultaneously; coupling of the mid infrared fiber into a multipass cell for enhanced pathlength and sensitivity; characterization of sources of instrument noise; and design work for a Phase II prototype.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗