Search NASA⌕ Search

SEARCH · Search NASA

Results for “CASTING MOLDS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Hot-Tearing Assessment of Multicomponent Nongrain-Refined Al-Cu Alloys for Permanent Mold Castings Based on Load Measurements in a Constrained Mold

The hot-tearing resistance of multicomponent Al-Cu alloys during permanent mold casting was investigated using a constrained permanent mold in which the load and temperature were measured. The nominal Cu composition was varied from 5 to 8 wt pct. Casting experiments were conducted without adding any grain-refining inoculants. The following variables, which were obtained from the measured load data during casting, were considered to assess the hot-tearing resistance of the Al-Cu multicomponent alloys: “V”-like signature in the load rate variation, load at solidus point, and load rate average over the freezing range. In addition, a hot-tearing criterion based on the variation of the fraction of solid in the late stages of solidification was used. It was found that all criteria considered can accurately predict the alloys with the lowest and highest hot-tear resistance, respectively. It was found that the rate of measured load during casting could be used to indicate substantial hot tearing. However, the load rate variation could not be used to detect when small hot tears were present. Among all the criteria considered, the load at the solidus point shows an excellent agreement with experimentally observed hot-tearing resistance for all but one alloy. The poorly resistant hot-tearing alloys exhibited mainly coarse columnar grains while the most hot-tearing resistant alloys exhibited a much more refined grain microstructure. This is the first study in which good hot-tear resistance is demonstrated for multicomponent Al-Cu alloys with nominal Cu content greater than 7 wt pct.

36 MATERIALS SCIENCE↗

Heat Transfer Coefficient at Cast-Mold Interface During Centrifugal Casting: Calculation of Air Gap

During centrifugal casting, the thermal resistance at the cast-mold interface represents a main blockage mechanism for heat transfer. In addition to the refractory coating, an air gap begins to form due to the shrinkage of the casting and the mold expansion, under the continuous influence of strong centrifugal forces. Here, the heat transfer coefficient at the cast-mold interface h has been determined from calculations of the air gap thickness d{sub a} based on a plane stress model taking into account thermoelastic stresses, centrifugal forces, plastic deformations, and a temperature-dependent Young’s modulus. The numerical approach proposed here is rather novel and tries to offer an alternative to the empirical formulas usually used in numerical simulations for a description of a time-dependent heat transfer coefficient h. Several numerical tests were performed for different coating thicknesses d{sub C}, rotation rates Ω, and temperatures of solidus T{sub sol}. Results demonstrated that the scenario at the interface is unique for each set of parameters, hindering the possibility of employing empirical formulas without a preceding experiment being performed. Initial values of h are simply equivalent to the ratio of the coating thermal conductivity and its thickness (~ 1000 Wm{sup −2} K{sup −1}). Later, when the air gap is formed, h drops exponentially to values at least one order of magnitude smaller (~ 100 Wm{sup −2} K{sup −1}).

36 MATERIALS SCIENCE↗

Light Metals Permanent Mold Casting

Current vehicles use mostly ferrous components for structural applications. It is possible to reduce the weight of the vehicle by substituting these parts with those made from light metals such as aluminum and magnesium. Many alloys and manufacturing processes can be used to produce these light metal components and casting is known to be most economical. One of the high integrity casting processes is permanent mold casting which is the focus of this research report. Many aluminum alloy castings used in automotive applications are produced by the sand casting process. Also, aluminum-silicon (Al-Si) alloys are the most widely used alloy systems for automotive applications. It is possible that by using high strength aluminum alloys based on an aluminum-copper (Al-Cu) system and permanent mold casting, the performance of these components can be enhanced significantly. This will also help to further reduce the weight. However, many technological obstacles need to be overcome before using these alloys in automotive applications in an economical way. There is very limited information in the open literature on gravity and low-pressure permanent mold casting of high strength aluminum alloys. This report summarizes the results and issues encountered during the casting trials of high strength aluminum alloy 206.0 (Al-Cu alloy) and moderate strength alloy 535.0 (Al-Mg alloy). Five engineering components were cast by gravity tilt-pour or low pressure permanent mold casting processes at CanmetMATERIALS (CMAT) and two production foundries. The results of the casting trials show that high integrity engineering components can be produced successfully from both alloys if specific processing parameters are used. It was shown that a combination of melt processing and mold temperature is necessary for the elimination of hot tears in both alloys.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Permanent Mold Casting of JIS-AC4C Aluminum Alloy Using a Low-Temperature Mold

Permanent mold casting using mold temperatures below 200 deg. C was conducted to obtain a high-strength, thin-walled casting. Al-7.36 mass% Si -0.18 Cu- 0.27Mg-0.34Fe alloy JIS-AC4C was cast using a bottom pouring cast plan. The product had a rectangular tube shape (70 mm W x 68 mm D x 180 mm H) with wall thicknesses of 1, 3 and 5 mm. The effect of heat insulation at the melt path was compared when using a sand runner insert and when using a steel runner insert as well as a powder mold release agent. Fine microstructures were observed in the casting. The smaller the thickness, the higher the hardness with smaller secondary dendrite arm spacing (SDAS). However, the hardness and the SDAS were unaffected by the mold temperature. It was proposed that the avoidance of the formation of primary {alpha} dendrite at the melt path generates a higher strength casting with adequate mold filling.

36 MATERIALS SCIENCE↗

Characterization of fold defects in AZ91D and AE42 magnesium alloy permanent mold castings

Casting premium-quality magnesium alloy components for aerospace and automotive applications poses unique challenges. Magnesium alloys are known to freeze rapidly prior to filling a casting cavity, resulting in misruns and cold shuts. In addition, melt oxidation, solute segregation and turbulent metal flow during casting contribute to the formation of fold defects. In this research, formation of fold defects in AZ91D and AE42 magnesium alloys cast via the permanent mold casting process was investigated. Computer simulations of the casting process predicted the development of a turbulent metal flow in a critical casting region with abrupt geometrical transitions. SEM and light optical microscopy examinations revealed the presence of folds in this region for both alloys. However, each alloy exhibited a unique mechanism responsible for fold formation. In the AZ91D alloy, melt oxidation and velocity gradients in the critical casting region prevented fusion of merging metal front streams. In the AE42 alloy, limited solubility of rare-earth intermetallic compounds in the {alpha}-Mg phase resulted in segregation of Al{sub 2}RE particles at the leading edge of a metal front and created microstructural inhomogeneity across the fold.

36 MATERIALS SCIENCE↗

Large Eddy Simulations of Electromagnetic Braking Effects on Argon Bubble Transport and Capture in a Steel Continuous Casting Mold

In continuous casting of steel, argon gas is often injected to prevent clogging of the nozzle, but the bubbles affect the flow pattern, and may become entrapped to form defects in the final product. Further, an electromagnetic field is frequently applied to induce a braking effect on the flow field and modify the inclusion transport. In this study, a previously validated GPU-based in-house code CUFLOW is used to investigate the effect of electromagnetic braking on turbulent flow, bubble transport, and capture. Well-resolved large eddy simulations are combined with two-way coupled Lagrangian computations of the bubbles. The drag coefficient on the bubbles is modified to account for the effects of the magnetic field. The distribution of the argon bubbles, capture, and escape rates, are presented and compared with and without the magnetic field. The bubble capture patterns are also compared with results of a previous RANS model as well as with plant measurements.

36 MATERIALS SCIENCE↗

Effects of Simultaneous Static and Traveling Magnetic Fields on the Molten Steel Flow in a Continuous Casting Mold

The drawback of steel fluid flow phenomena for a continuous casting mold under an electromagnetic stirrer with a traveling magnetic field is the resulting severe meniscus fluctuations due to the high-velocity and excessive downward flow in the casting direction. This can result in slab surface defects due to mold flux or inclusion entrainment. To inhibit these defects in the as-cast steel products, the implementation of braking forces using static magnetic fields in combination with a traveling magnetic field was studied in the current study. The numerical results of the fluid flow in the mold under a combined traveling and static magnetic field operation show not only 50 pct lower downward flow speed, but also more enhanced rotational flow to improve washing effects. The numerical results were validated in commercial-scale operations. The results suggest the optimized range of the ratio between the traveling and static magnetic flux densities is 65 to 75 pct to ensure steel quality improvements; this range maintains a balance between the fluid forces from the jet flow and the magnetic forces in the mold.

36 MATERIALS SCIENCE↗

Scale-Adaptive Simulation of Transient Two-Phase Flow in Continuous-Casting Mold

Scale-adaptive simulation (SAS) of the transient gas–liquid two-phase flow in a laboratory-scale continuous-casting mold is presented. The main objective is to investigate the applicability of the scale-adaptive unsteady Reynolds-averaged Navier–Stokes turbulent model (URANS SAS) for predicting the transient multiscale turbulent structures in a two-phase flow. Good quantitative agreements with the experimental data and the large eddy simulation (LES) results are obtained both for the time-averaged velocity field and for the transient turbulent characteristics. The introduction of the von Karman length-scale into the turbulence-scale equation allows the SAS model to dynamically adjust to the resolved turbulent structures. The LES-like pulsating behavior of the air gas and the large-scale liquid eddy magnitudes in the unsteady regions of flow field are captured by the SAS model. The classical − 5/3 law of power spectrum density (PSD) of the axial velocity is kept properly for the single-phase turbulent flow. For two-phase flow, the decay of PSD is too steep at the high-frequency region; the predicted PSD obtained with SAS is damped stronger than that estimated by LES. The SAS model offers an attractive alternative to the existing LES approach or to the other hybrid RANS/LES models for strongly unsteady flows.

36 MATERIALS SCIENCE↗

Development of Metal Casting Molds By Sol-Gel Technology Using Planetary Resources

Metals extracted from planetary soils will eventually need to be casted and shaped in-situ to produce useful products. In response to this challenge, we propose to develop and demonstrate the manufacturing of a specific product using Lunar and Martian soil simulants, i.e. a mold for the casting of metal and alloy parts, which will be an indispensable tool for the survival of outposts on the Moon and Mars. Drawing from our combined knowledge of sol-gel and metal casting technologies, we set out to demonstrate the extraordinary potential of mesoporous materials such as aerogels to serve as efficient casting molds as well as fulfilling numerous other needs of an autonomous planetary outpost.

Sibille, L.↗

Characterization of Roughness, Porosity and Thermal Resistances of Continuous Casting Mold Slag Layers Devitrified and Crystallized in Laboratory

This paper presents an experimental investigation about the variation, with temperature, of surface roughness, porosity, degree of crystallization and microstructure, occurring in solid layers of a commercial mold powder slag used for casting medium carbon steel thin slabs. Characterization is done with samples devitrified and crystallized at 698 K, 823 K, 898 K and 973 K (425 °C, 550 °C, 625 °C and 700 °C) for 10,800 seconds, in the furnace of a high-temperature confocal laser scanning microscope. As well as, with slag disks devitrified non-isothermally in a heat flow apparatus based on the application of Fourier's law in steady state conditions, where the high temperature surface is maintained at selected values, between 927 K and 1241 K (654 °C and 968 °C). Surface roughness and porosity determinations are performed by image analysis of confocal laser scanning and scanning electron micrographs, respectively. For the time considered and temperatures ≥ 823 K (550 °C) the slag crystallizes completely, and variations of roughness and porosity with temperature are associated with changes in size and packing of the primary crystalline-phase grains. Crystallization induced porosity is significant and causes slag layer expansion. Hence crystallization does not lead to gap formation with a neighboring surface (e.g., mold wall) by shrinkage. Instead, surface separation arises from development of roughness, and measurements with the heat flow apparatus confirm that interfacial thermal resistance between a slag layer and a metallic wall can be estimated from the sum of the means of maximum peak to valley height of their surfaces. Furthermore, the results establish that slag layers roughness and porosity increase with temperature and reveal effective thermal conductivities in the range of ~ 0.3 to ~ 0.5 W/m K. Low effective thermal conductivities must be a consequence of porous bands, whose porosity depends on temperature and reaches values as high as ~ 0.20 and ~ 0.50.

36 MATERIALS SCIENCE↗

A Physical Model to Study the Effects of Nozzle Design on Dispersed Two-Phase Flows in a Slab Mold Casting Ultra-Low-Carbon Steels

The effects of nozzle design on dispersed, two-phase flows of the steel-argon system in a slab mold are studied using a water-air model with particle image velocimetry and ultrasound probe velocimetry techniques. Three nozzle designs were tested with the same bore size and different port geometries, including square (S), special bottom design with square ports (U), and circular (C). The meniscus velocities of the liquid increase two- or threefold in two-phase flows regarding one-phase flows using low flow rates of the gas phase. This effect is due to the dragging effects on bubbles by the liquid jets forming two-way coupled flows. Liquid velocities (primary phase) along the narrow face of the mold also are higher for two-phase flows. Flows using nozzle U are less dependent on the effects of the secondary phase (air). The smallest bubble sizes are obtained using nozzle U, which confirms that bubble breakup is dependent on the strain rates of the fluid and dissipation of kinetic energy in the nozzle bottom and port edges. Through dimensionless analysis, it was found that the bubble sizes are inversely proportional to the dissipation rate of the turbulent kinetic energy, ε{sup 0.4}. A simple expression involving ε, surface tension, and density of metal is derived to scale up bubble sizes in water to bubble sizes in steel with different degrees of deoxidation. The validity of water-air models to study steel-argon flows is discussed. Prior works related with experiments to model argon bubbling in steel slab molds under nonwetting conditions are critically reviewed.

36 MATERIALS SCIENCE↗

Stress and Friction Distribution around Slab Corner in Continuous Casting Mold with Different Corner Structures

The non-uniform friction and thermal stress in the mold are important as causes of the transverse cracks around strand corner. To analyze the stress distribution features around strand corner, a three-dimensional thermo-elastoplastic finite-element mold model with different corner structures (right-angle, big-chamfer, multi-chamfer, and fillet) was established. The temperature field in the mold was indirectly coupled through a three-dimensional fluid flow and heat transfer model. In addition, the non-uniform mold friction stress loaded on the strand surface was calculated through a friction model. The results show that the stress distribution on the shell is similar to the temperature distribution. The stress concentration appears in the strand corner and the lower part of wide face. The friction stress enhances the corner stress around the edge of the air-gap. For chamfered molds, the stress around the corner between the wide face and chamfer face is larger than that between the narrow face and chamfer face. Around the corner region, both the stress peak and the area of the large stress zone of the right-angle strand are the largest, while those of big-chamfered, multi-chamfered, and fillet strands decrease in that order. The stress peak position of the chamfered strands is closer to the mold exit than that of the right-angle strand. Compared with the use of the right-angle mold, the application of chamfered molds is able to reduce the stress concentration around the strand corner.

36 MATERIALS SCIENCE↗

Numerical Simulation of the Effects of Horizontal and Vertical EMBr on Jet Flow and Mold Level Fluctuation in Continuous Casting

In this article, a new type of electromagnetic braking (EMBr), named vertical EMBr (V-EMBr) was introduced in the continuous casting process. In order to investigate its capability and applicability, the impacts of horizontal and vertical EMBrs on the flow pattern in a continuous casting mold were simulated by means of an implemented Reynolds-averaged Navier–Stokes (RANS) SST k–ω turbulence model. The characteristics of electromagnetic field and flow field inside a 1450 mm × 230 mm mold with Ruler-EMBr and V-EMBr have been compared. The numerical simulation results indicate that the static magnetic field generated by Ruler-EMBr can cover the main part of the discharging jet flow, which has a better control of the flow pattern in lower part of the mold. The static magnetic field generated by V-EMBr can cover both the vicinity of the mold narrow faces and the impingement region of the jet flow, which can effectively control the liquid steel flow in the upper recirculation zone. The parametric study also shows that the large vortices beneath the jet flow can be almost completely eliminated at an optimized magnetic flux density with Ruler-EMBr. In addition, the surface velocity and steel/slag interface fluctuation can be suppressed with the application of V-EMBr to acceptable values even with a wide variation of SEN port angles. It is estimated that to reach the same level of braking effect on the upper recirculation flow, a magnetic flux density of 0.1 T is sufficient for V-EMBr, while 0.2 T is needed for Ruler-EMBr. Based on the results, a second-generation V-EMBr has been developed, which combines both of the merits of Ruler-EMBr and V-EMBr.

36 MATERIALS SCIENCE↗

Water soluble barrier coatings for washout tooling for a composite layup

A washout tooling for a composite layup is provided. The washout tooling comprises a casting mold having an exterior surface. The casting mold comprises a particulate material and a water-soluble binder. The casting mold is adapted to break down in the presence of an aqueous solution. The washout tooling further comprises a water-soluble coating layer overlying the exterior surface. The water-soluble coating layer is adapted to break down in the presence of an aqueous solution. The washout tooling further comprises a curable composite layer overlying the water-soluble coating layer. The water-soluble coating layer minimizes contact between the particulate material and the curable composite layer.

Saito, Tomonori↗

New methods and materials for molding and casting ice formations

This study was designed to find improved materials and techniques for molding and casting natural or simulated ice shapes that could replace the wax and plaster method. By utilizing modern molding and casting materials and techniques, a new methodology was developed that provides excellent reproduction, low-temperature capability, and reasonable turnaround time. The resulting casts are accurate and tough.

Reehorst, Andrew L.↗

Integrated Approach to Density-Based Spatial Clustering of Applications with Noise and Dynamic Time Warping for Breakout Prediction in Slab Continuous Casting

Mold breakout is a catastrophic accident that has serious impacts on smooth production, slab quality, and caster equipment. Accurate identification and prediction of an impending breakout are always top priorities in continuous casting operations. In view of crucial common features of mold copper plate temperatures during a breakout, such as time lag and space inversion, the concepts of density-based spatial clustering of applications with noise and dynamic time warping are introduced, and an integrated novel method for breakout prediction is developed. Through extracting and fusing the representative singularity and approximation of temperature variation, the typical temporal and spatial temperature characteristics during breakout can be distinguished and predicted accurately. Compared with traditional methods of logical judgment and artificial neural network, the method based on clustering does not need to modify forecast thresholds or parameters artificially, which overcomes the limitation of model dependence on human beings, and demonstrates excellent adaptability and robustness for online abnormality prevention.

36 MATERIALS SCIENCE↗